AI port High Speed Asynchronous Line Card Installation Guide

Size: px

Start display at page:

Download "AI port High Speed Asynchronous Line Card Installation Guide"

Cecil Carr
5 years ago
Views:

AI232 32-port High Speed Asynchronous Line Card Installation Guide

2 Copyright 2008 by Kentrox, Inc. All Rights Reserved. The material discussed in this publication is the proprietary property of Kentrox, Inc. Kentrox retains all rights to reproduction and distribution of this publication. Kentrox is a registered trademark of Kentrox, Inc. Applied Innovation, Applied Innovation Inc., the AI logo, and other names are the intellectual property of Kentrox. All other product names are trademarks or registered trademarks of their respective owners. Information published here is current as of this document s date of publication, but is subject to change without notice. You may verify product information by contacting our headquarters in Oregon. Kentrox is an Equal Opportunity/Affirmative Action employer. Kentrox, Inc Innovation Dr. Dublin, Ohio USA Toll Free: (800) International: +1 (614) Fax: +1 (614) NW Tanasbourne Dr. Hillsboro, Oregon USA Toll Free: (800) Direct: (503)

3 AI port High Speed Asynchronous Line Card Installation Guide This installation guide explains how to install an AI port high speed asynchronous line card. Guide to this document Cautions and Warnings Customer Assistance Introduction Model DP232-19/23 Distribution Panel Model DP232-RJ45 Distribution Panel 1

4 Cautions and Warnings Cautions and Warnings Grounding and Electrical Safety Installation CAUTION: AI equipment and its peripherals contain electrostatic sensitive components. Proper handling, shipping, and storage precautions must be exercised: You must remove and install cards in a static-free environment. Wear an antistatic wrist strap that is plugged into the AI equipment so you are grounded at the same point as the equipment. Do not remove cards from their antistatic plastic bags until you are ready to install them into the chassis. Immediately after you remove a card from the chassis, you must insert it into its antistatic bag. When the cards are not in use, keep them in their antistatic plastic bags. Do not ship or store cards near strong electrostatic, electromagnetic, or radioactive fields. CAUTION: For AI equipment to operate safely and correctly, there must be a safety ground strap between the equipment ground bolts and the office ground. Environment CAUTION: In the event that AI232 has been subjected to adverse environmental conditions, a service inspection of AI232 should be made to ensure safe operation. FCC The Federal Communications Commission has set limits for emitted radio interference, and AI232 is constructed with this electromagnetic interference (EMI) limitation in mind. AI232 is classified under FCC regulations as a Class A device, that is, a device for use in commercial environments and not in residential areas. This device has been tested and shown to comply with the following FCC rule: Part 15 Subpart J. Operation of this equipment in a residential area may cause interference to radio and TV reception, requiring the user to take whatever steps are necessary to correct the interference. 2

5 Customer Assistance Information is available from the FCC describing possible corrective actions. To maintain low EMI levels, we suggest that you use only metal connectors and shielded cable grounded to the frame. Specifications are subject to change without notice. Customer Assistance Kentrox offers technical support 24 hours a day, seven days a week. Before you contact Kentrox for assistance, please have the following information available: The type of hardware and software you are using The error number and exact wording of any messages that appeared on your screen What happened and what you were doing when the problem occurred How you tried to solve the problem Web Site Support Support is available 24 hours a day using our Web site at: Support support is available 24 hours a day. When you use support, please be sure to include the details of your problem within the . To contact Technical Support, send to: techsupport@aiinet.com Phone Support Phone support is available. When you call Kentrox for support, please be sure you are at your computer and have the details of your problem available. To contact Technical Support, call (866) Kentrox Product Documentation To order documentation, please contact your sales representative at (800) or +1 (614) You can also access and view the most current versions of Kentrox product documentation on our Web site at: 3

6 Introduction Introduction Distribution panels provide the physical interface for the AI232 network interface card. The distribution panels are available in two models providing these interfaces: Model DP232-19/23: 16 DB-25/EIA-232-E interfaces Model DP232-RJ45: 32 RJ-45/EIA-232-E signals Model DP232-19/23 Distribution Panel This distribution panel provides 16 DB-25/EIA-232-E interfaces for the AI232. Two distribution panels are required to access all 32 ports on the AI232. The distribution panel is available in two sizes for 19-inch or 23-inch rack installations. Figure 1 shows the distribution panel and Table 1 lists the specifications. Figure 1: DP232-19/23 Distribution Panel Connect to Network Elements (16 ports) Connect to the AI232 PORT 1/17 PORT 5/21 PORT 9/25 PORT 13/29 PORT 2/18 PORT 6/22 PORT 10/26 PORT 14/30 PORT 3/19 PORTS PORT 7/23 DP232 PORT 11/27 PORTS PORT 15/ APPLIED INNOVATION INC PORT 4/20 PORT 8/24 COPYRIGHT 1999 PORT 12/28 PORT 16/32 Table 1: Specifications for DP232-19/23 Description Mounting I/O Ports Weight (approximately) Size Specification DP232-19: mounts to a 19-inch rack DP232-23: mounts to a 23-inch rack 16 DB-25/EIA-232-E interfaces 2.5 lb (1.12 kg) Height: 4 in. (10.16 cm) Width: 19 in. (48.26 cm)/23 in. (58.42 cm) Depth: 1.12 in. (2.84 cm) 4

7 Model DP232-19/23 Distribution Panel Table 1: Specifications for DP232-19/23 (Continued) Description Pin Assignments Specification Pin 1 Pin 14 Pin 13 Pin 25 Pin Signal 2 TXD 3 RXD 4 RTS 5 CTS 6 DSR 7 Signal GND 8 DCD 20 DTR Cables CAB467: Connects one connector (8 ports) on the AI232 to the distribution panel. Each distribution panel requires two cables. CAB469: Connects network elements to the individual connectors on the distribution panel. 5

8 Model DP232-19/23 Distribution Panel Installation Procedure 1. Install the distribution panel(s) to the rack. Figure 2 shows a typical installation. 2. Attach cables from the AI232 to the distribution panel. Figure 2: Typical Installation Cable: CAB467 (4 places) PORT 1 PORT 2 DP232-19/23 PORT 5 PORT 9 PORT 6 PORT 10 PORT 13 PORT 14 PORT 3 PORTS 1-8 PORT 7 PORT 11 PORTS 9-16 PORT 15 PORT 4 PORT 8 PORT 12 PORT 16 PORT 1 PORT 5 PORT 9 PORT 13 PORT 2 PORT 6 PORT 10 PORT 14 PORT 3 PORTS 1-8 PORT 7 PORT 11 PORTS 9-16 PORT 15 PORT 4 PORT 8 PORT 12 PORT AI232 (AI180 Chassis) 6

9 Model DP232-RJ45 Distribution Panel Model DP232-RJ45 Distribution Panel This model provides 32 RJ-45/EIA-232-E signals for the AI232. Reversible mounting flanges allow installation to a 19-inch or 23-inch rack. Figure 3 shows the distribution panel and Table 2 lists the specifications. Figure 3: DP232-RJ45 Distribution Panel Connect to Network Elements Connect to the AI232 (32 ports) (4 places) PORTS 1-8 PORTS DP232-RJ45 PORTS PORTS Table 2: Specifications for DP232-RJ45 Description Specification Mounting Reversible mounting flanges allow installation to a 19- inch or 23-inch rack. I/O Ports Weight (approximately) Size 32 RJ-45 ports 4.8 lb (2.16 kg) Height: 2 in. (5.08 cm) Width: 16.9 in. (42.92 cm) without mounting flanges Depth: 3.5 in. (8.89 cm) Pin Assignments Pin 1 Pin 8 Pin Signal 1 RTS 2 DTR 3 TXD 4 DCD 5 RXD 6 GND 7 DSR 8 CTS 7

10 Model DP232-RJ45 Distribution Panel Table 2: Specifications for DP232-RJ45 (Continued) Description Specification Cables CAB467: Connects one connector (8 ports) on the AI232 to the distribution panel. The distribution panel requires four cables. CAB182: Connects network elements to the individual connectors on the distribution panel (straight through applications). Installation Procedure 1. Attach the mounting flanges and tie bar as shown in Figure 4. (Table 3 shows the part list.) Figure 4: DP232-RJ45 Distribution Panel PORTS 1-8 PORTS DP232-RJ45 PORTS PORTS Setting flanges for a 19-inch rack Install the mounting flanges in the desired location Setting flanges for a 23-inch rack Install the mounting flanges in the desired location Table 3: Parts List Item Description Part No. Quantity 1 Tie Bar Mounting Flange (left side)

11 Model DP232-RJ45 Distribution Panel Table 3: Parts List Item Description Part No. Quantity 3 Mounting Flange (right side) #6-32 Screw with lockwasher #12-24 Screw with lockwasher Install the distribution panel to the rack. Figure 5 shows a typical installation. Figure 5: Typical Installation Cable: CAB467 (4 places) DP232-RJ PORTS 1-8 PORTS DP232-RJ45 PORTS PORTS AI232 AI180 Chassis 9

12 10 Model DP232-RJ45 Distribution Panel

AI180I AIswitch Series 180 Integrated Chassis Installation Guide

AI180I AIswitch Series 180 Integrated Chassis Installation Guide Part Number QR-180I Rev 5 2008 by Kentrox, Inc. All rights reserved. Copyright 2008 by Kentrox, Inc. All Rights Reserved. The material discussed