Instruction Manual scancontrol 27x0

Transcription

1 Instruction Manual

2 Laser scanner MICRO-EPSILON MESSTECHNIK GmbH & Co. KG Königbacher Strasse Ortenburg / Germany Tel. +49 () 8542 / 168- Fax +49 () 8542 / info@micro-epsilon.de Certified acc. to DIN EN ISO 91: 28

3 Contents 1. Safety Symbols Used Warnings CE Compliance Proper Use Proper Environment Laser Safety Laser Class 2M Laser Class 3B Functioning Principle, Technical Data Brief Description Measurement Principle System Setup Special Performance Features Advantages of the Used Sensor Array (Difference to Conventional Line Scanners) Further Features Technical Data LED Indicators Delivery Standard Equipment Storage Mounting Attachment and Mounting of the Sensor Connections Power Supply RS422, Synchronization, Switching Signals Ethernet Connection External Laser Switching Installation Instructions Recommended Connector and Cable Types Mounting the Connectors Getting Ready for Operation, Commissioning... 41

4 6. Operation of the Sensor with a PC Displays Operating and Demonstration Programs Installation and Requirements Requirements Installation Instructions for Operating Measuring Field Selection Calibration Automatic Exposure Time Regulation Error Influences Reflection Factor of the Target Surface Color Differences Temperature Influences External Light Mechanical Vibrations Surface Roughness Shadowing Effects Cleaning scancontrol Output Unit scancontrol Output Unit - Components Connect the Supply Voltage Commissioning scancontrol Output Unit Specification of the Components Output Unit Basic (Ethernet) Supported Modules OU-DigitalOut/8-Channel/DC24 V/.5 A/High-side Switching/8 Actuators OU-AnalogOut/4-Channel/-1 V Warranty Service, Repair Decommissioning, Disposal Error Codes... 63

5 Appendix A 1 Accessories A 1.1 Recommended Accessories A 1.2 Optional Accessories... 66

6

7 Safety 1. Safety Knowledge of the operating instructions is a prerequisite for equipment operation. 1.1 Symbols Used The following symbols are used in the instruction manual: Indicates a hazardous situation which, if not avoided, may result in minor or moderate injury. Indicates a situation which, if not avoided, may lead to property damage. i Measure 1.2 Warnings Indicates a user action. Indicates a user tip. Indicates a hardware or a button/menu in the software Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Avoid unnecessary laser radiation to be exposed to the human body - Switch off the sensor for cleaning and maintenance. - Switch off the sensor for system maintenance and repair if the sensor is integrated into a system. The power supply and the display-/output device must be connected in accordance with the safety regulations for electrical equipment > Danger of injury > Damage to or destruction of the sensor Avoid shock and vibration to the sensor. > > Damage to or destruction of the sensor The power supply may not exceed the specified limits > Damage to or destruction of the sensor Page 7

8 Safety Avoid continuous exposure to dust and spray on the sensor by appropriate methods such as blowing or using a protective housing. > Damage to or destruction of the sensor Do not touch the protective windows of the optics with the fingers. Wipe off any fingerprints immediately with pure alcohol and a clean cotton cloth with no streaks. Protect the cable against damage. > > Failure of the measuring device Switch off the sensor always first before you connect or disconnect devices. 1.3 CE Compliance The following applies to the sensor: EU directive 214/3/EU EU directive 211/65/EU, RoHS category 9 Products which carry the CE mark satisfy the requirements of the quoted EU directives and the European standards (EN) listed therein. The EC declaration of conformity is kept available according to EC regulation, article 1 by the authorities responsible at MICRO-EPSILON MESSTECHNIK GmbH & Co. KG Königbacher Straße Ortenburg / Germany The sensor is designed for use in industry and satisfies the requirements. Page 8

9 Safety 1.4 Proper Use The sensor is designed for use in industrial and laboratory areas. It is used for Profile measurement Length measurement Quality monitoring and inspection of dimensions The system may only be operated within the limits specified in the technical data, see Chap The system should only be used in such a way that in case of malfunction or failure personnel or machinery are not endangered. Additional precautions for safety and damage prevention must be taken for safety-related applications. 1.5 Proper Environment Protection class sensor: IP 65 (applies only when connected output connectors respectively protective caps) Operating temperature: to +5 C (+32 to +122 F) Humidity: 5-95% (non condensing) Ambient pressure: atmospheric pressure Vibration: according to DIN EN (sine shaped) Mechanical shock: according to DIN EN (continuous shock) The protection class does not apply for the optical sections during operation as their soiling / contamination results in adversely affecting or failure of the function. Only use screened cables or original cables from the range of accessories for the connection to a power supply and for the outputs. Note also the assembly and installation instructions, see Chap. 5. The IP 65 protection class is a specification which is limited to the protection with respect to dust and water. Oil, steam and emulsion penetration are not included in this protection class and must be tested separately. Page 9

10 Laser Safety 2. Laser Safety The sensors operate with a semiconductor laser having a wavelength of 66 nm (visible/red). The laser operation is indicated visually by the LED on the sensor. When operating the sensors, the relevant regulations according to EN (IEC 6825, Part 1 of and the applicable accident prevention regulations must be followed. The housing of the optical sensors must only be opened by authorized persons, see Chap. 8. For repair and service, the sensors should always be returned to the manufacturer. 2.1 Laser Class 2M Hazard to the eye via laser radiation! Consciously close the eyes or turn away if the laser radiation impinges on the eye. sensors with a maximum laser power up to 1 mw, see Chap. 3.2, are classified in Laser Class 2M (IIM). Accordingly, the following applies: With laser equipment of the Class 2M, the eye is not put in danger during random, short-term exposure to the laser radiation, i.e. exposure duration up to.25 s. A direct glimpse into the beam can be dangerous if the eye-closure reflex is deliberately suppressed, e.g. during adjustment. Direct viewing into the beam with optical aids, e.g. a magnifying glass, is dangerous. Laser equipment of the Class 2M can be employed without further protective measures, when deliberate viewing into the laser beam or into a beam reflected by mirrors is not longer than.25 s. Since generally the presence of the eye-closure reflex should not be assumed, one should close the eyes or immediately turn away if the laser radiation impinges on the eye. The following information labels are fitted to the sensor housing (front and rear side): Laser radiation Do not stare into the beam or expose users of telescope optics Class 2M Laser Product IEC : P 1 mw; E 65W/m²; =66 nm Laser label class 2M IEC Only for USA The laser labels for Germany are already printed on. The labels for the EU area and the USA are enclosed and must be fitted by the user for the region applicable in each case before the equipment is put into operation. Page 1

11 Laser Safety Lasers of Class 2M are not subject to notification and a laser protection officer is not required. Mark the laser area recognizable and everlasting. If both information labels are hidden in the installed state, the user must ensure that additional labels are fitted at the point of installation. i scancontrol Laser radiation Do not stare into the beam or expose users of telescope optics Class 2M Laser Product IEC : P 1 mw; E 65W/m²; =66 nm Laser spot Fig. 1 True reproduction of the sensor with its actual location of the warning label Injury to the eye or the skin via laser radiation! Consciously close the eyes or turn away if the laser radiation impinges on the eye or the skin. Page 11

12 Laser Safety 2.2 Laser Class 3B sensors with a maximum laser power up to 2 mw, see Chap. 3.2, are classified in Laser Class 3B (IIIB). i Sensors of laser class 3B (IIIB) need an external key switch to switch off the laser, see Chap Accordingly, the following applies: The available laser radiation is hazardous for the eyes and usually for the skin also. Looking directly into the laser beam is hazardous for the eyes. Also reflections on shining or mirroring surfaces can be hazardous to the eye. Hazards to the skin through the available laser radiation are given by class 3B (IIIB) laser equipment if the values of the maximum permissible exposure are exceeded. If the sensor is on the laser output can be reduced to 1 mw with the software. Reducing the laser output to 1 mw is not possible. Reducing the laser output from 2 mw to 1 mw with a software affects not the laser class! The following information label should be fitted to the sensor housing (front and rear side): i Warning - Laser radiation Avoid exposure to beam Class 3B Laser Product IEC : P 5mW ; =66nm IEC label Only for USA The laser labels for Germany are already printed on. The labels for the EU area and the USA are enclosed and must be fitted by the user for the region applicable in each case before the equipment is put into operation. If both information labels are hidden in the installed state, the user must ensure that additional labels are fitted at the point of installation. Page 12

13 Laser Safety Beam attenuator When using lasers of 3B class appropriate protective glasses are necessarily! > Injury of the eyes and the skin by laser radiation. Fig. 2 scancontrol beam attenuator masks aperture Fig. 3 scancontrol beam attenuator in measuring position Laser products certified as Class 3B products (EN ) require a beam attenuator, see Fig. 2, see Fig. 3, other then the key-operated control. The beam attenuator prevents access to all laser and collateral radiation. To open or close the aperture please follow the steps below: Unscrew the knurled screw, Change the attenuator position and tighten the knurled screw. The laser aperture must be open during measurement. Page 13

14 Laser Safety scancontrol Warning - Laser radiation Avoid exposure to beam Class 3B Laser Product IEC : P 5mW ; =66nm Laser spot Fig. 4 True reproduction of the sensor with its actual location of the warning label The user is responsible that the accident prevention regulations are observed. Class 3B (IIIB) laser sensors are notifiable and a laser protection officer is required either. Mark the laser area recognizable and everlasting. During operation the laser area has to be restricted and marked. Observe the instructions described, see Chap Page 14

15 Functioning Principle, Technical Data 3. Functioning Principle, Technical Data 3.1 Brief Description Measurement Principle The sensor operates according to the principle of optical triangulation (light intersection method): A laser line is projected onto the target surface via a linear optical system. The diffusely reflected light from the laser line is replicated on a sensor array by a high quality optical system and evaluated in two dimensions. The laser line triangulation corresponds in principle to the triangulation of a laser point. In addition, during the measurement a row of lines are simultaneously illuminated by the laser line. Apart from the distance information (Z-axis), the exact position of each point on the laser line (X-axis) is also acquired and output by the system System Setup The measuring system is a compact sensor with an integrated controller. All necessary integral parts are combined in one housing Special Performance Features scancontrol features speed and compact design with simultaneously high measurement accuracy. A special line-scanning optical system ensures uniform exposure of the measuring field. The sensor array is arranged in the sensor head according to the Scheimpflug condition which facilitates uniform image focusing over the whole depth of the measurement range (Z-axis). scancontrol works even without a PC in conjunction with saved configurations. The sensor runs the profile measurement internally and calculates default measured values such as angle or edge position. The measured values can be processed directly in a PLC via the digital inputs /outputs in connection with the scancontrol Output Unit. Furthermore, a determination of internal limit value with subsequent output of the evaluation results (good / bad) is possible via the switching outputs. This series with integrated profile evaluation is named scancontrol 271. Page 15

16 Functioning Principle, Technical Data Receiver Light source Target Fig. 5 Basic design X-Axis Z-Axis Measuring field Advantages of the Used Sensor Array (Difference to Conventional Line Scanners) A global shutter (high speed shutter) for the whole profile enables a high profile accuracy for fast applications. The array enables the simultaneous exposure and reading of the previous image. Thus the exposure time is longer at the same profile frequency. With it also dark objects can be measured with a high rate Further Features The sensors are available in two versions: Connectors on the front or on the rear side. External synchronization and triggering. Serial interface (RS422) for communication with PLCs or PCs. The automatic control of the exposure time enables consistent measurement results with changing surfaces. This function can be switched off on request. Ethernet 1/1 Mbit as fast standard connection to the PC. Page 16

17 Functioning Principle, Technical Data 3.2 Technical Data Model LLT27x-25 LLT27x-5 LLT27x-1 Measuring range z-axis 25 mm 5 mm 1 mm Start of measuring range 9 mm 175 mm 35 mm End of measuring range 115 mm 225 mm 45 mm Start of extended measuring range approx 85 mm 16 mm 3 mm End of extended measuring range approx. 125 mm 26 mm 6 mm Line length midrange, x-axis 25 mm 5 mm 1 mm Linearity 1 ±.2 % FSO (3 s) Resolution x-axis Profile frequency Light source 64 points/profile 27 / Hz Hz Semiconductor laser 66 nm (red) Aperture angle laser line 2 Laser power Standard 1 mw (laser class 2M), reduced 2-3 mw Integrated laser switch-off Cable length Optional Optional 2 mw (laser class 3B) 2, reduced 1 mw Safety interlock, hardware switch-off Ethernet: Up to 5 m without restrictions Protection class (DIN EN 6529 ) IP 64 Page 17

18 Functioning Principle, Technical Data Model LLT27x-25 LLT27x-5 LLT27x-1 Operating temperature Storage temperature Vibration Shock Output/Input State display Supply C to +5 C (+32 F to +122 F) -2 C to 7 C (-4 F to +158 F) 2 g / Hz (acc. to DIN EN , 1 cycles per axis) 15 g / 6 ms (acc. to DIN EN , 1 cycles each axis) Ethernet, laser off (optional), 1x RS422 programmable (interface or synchronization or encoder input) 1x laser, 1x power/error/status VDC, 5 ma Weight sensor appr. 7 g appr. 8 g appr. 85 g Galvanic isolation Only at RS422 and Ethernet, no isolation of 24V-supply, internal circuit If isolation necessary, external 24V-DC-DC-converter required FSO = Full scale output 1) Based on a MICRO-EPSILON Optronic standard target with metallic finished surfaces. 2) Sensors need an external key switch to switch off the laser to be classified in Laser Class 3B (IIIB), see Chap Page 18

19 Functioning Principle, Technical Data 3.4 LED Indicators laser on state LED laser on LED state : two-color LED (red / green) green: laser on green: measurement green flashing: data transmission red flashing: error code, see Chap. 11. Note: The state LED flashes green; long during active data transmission and short for controller accesses. Page 19

20 Delivery 4. Delivery 4.1 Standard Equipment 1 Sensor LLT27x 1 Assembly Instructions 1 Sensor inspection log 1 Bag of accessories, containing: 1 ODU male cable connector 6-pin (RS422), S31BQC-P6MFG-6, 2 Protective caps for ODU socket (6 or 8-pin), PC27-4.5; Power cable 4.5 m long; 2-core, shielded, with mounted ODU round connector and free cable ends PC27(2)-4.5; Power cable 4.5 m long for external laser switching; 6-core, shielded, with mounted ODU round connector and free cable ends for the sensor options and Data carrier (CD-ROM) with scancontrol Software CD (only scancontrol 27 and 275), demonstration programs and documents from MICRO-EPSILON Messtechnik. 1 Data carrier (CD-ROM) with scancontrol Configuration Tools (only scancontrol 271) Check the delivery for completeness and shipping damage immediately after unpacking. In case of damage or missing parts, please contact the manufacturer or supplier. You will find recommended and optional accessories in Appendix, see Chap. A 1.1, see Chap. A Storage Storage temperature: -2 to +7 C (-4 to +158 F) Humidity: 5-95 % (non-condensing) Page 2

21 Mounting 5. Mounting 5.1 Attachment and Mounting of the Sensor The sensor can be mounted in two different ways: 1. with 3 threaded holes M4 on the front side or 2. with 3 threaded holes M4 on the side surfaces. All threaded holes are 5 mm deep blind holes. Refer to the dimension drawings for the mounting dimensions. Pay attention to careful handling during mounting and operation. > Damage to or destruction of the sensor Pay attention to the depth of the blind holes during selection of the fixing screws > > Damage to the thread due to screws resting on it. The laser beam should strike the target surface at right angles. Otherwise, inaccurate measurements cannot be ruled out. Direct fastening Screw depth Screw Torque min approx. 5.5 mm M4 x ISO 4762-A2 2 Nm (µ =.12) Fig. 6 Mounting conditions The bearing surfaces surrounding the fastening holes (through-holes) are slightly raised. Mount the sensor only to the existing mounting holes / threaded holes on a flat surface. Clamps of any kind are not permitted. Do not exceed torques. > > Inaccurate, erroneous measuring values Page 21

22 Mounting A 5.6± C optically effective: max. ø1 optically effective: max. ø ø ø5.5 4x thread M4 for protection shield mounting; not for mounting the sensor R B Three mounting holes M4x5 on each layer A, B, C ø8 R Fig. 7 Dimensional drawing LLT27xx-25, dimensions in mm, not to scale Every three mounting holes M4x5 on three levels A, B, C Page 22

23 Mounting M4 5 deep Ø8 A C Fig. 8 Dimensional drawing LLT27xx-25, connectors on the rear side, dimensions in mm, not to scale Every three mounting holes M4x5 on three levels A, B, C 2.5 B Page 23

24 Mounting sensor field of view extended measuring range Standard measuring range 115 Extended measuring range extended measuring range laser line 2 Fig. 9 Measuring field assignment LLT27xx-25, dimensions in mm, not to scale Page 24

25 8ø Mounting C optically effective: max. ø A optically effective: max. ø ø ± ø5.5 4x thread M4 for protection shield mounting; not for mounting the sensor B 3 34 Three mounting holes M4x5 on each layer A, B, C R R Fig. 1 Dimensional drawing LLT27xx-5, dimensions in mm, not to scale Every three mounting holes M4x5 on three levels A, B, C Page 25

26 Mounting 22.5 (.88) 45 (1.77) 69 (2.71) 73 (2.87) 43 (1.69) 21 (.83) 68 (2.68) ø8 (.31) 12 (.47) 21 (.83) 5.5 (.22) 77 (3.3) 13 (5.12) 93.3 (3.67) 142 (5.59) 64.9 (2.55) 15 (4.13) 5 (.19) 13 (.51) 18 (.71) (.79) R2 63 (2.48) 73 (2.87) (.39) R1 1 (.39) 55 (2.16) 6 (2.36) 73 (2.87) (4.9) A 69 (2.72) 63.5 (2.5) C optical effect: max. ø1 (.39) optical effect: max. ø18 (.71) 34 (1.34) 3 (1.18) 34.5 (1.36) 69 (2.72) 68 (2.68) 5.5 (.22) ø5.5 (.22) 4x M4 thread for mounting shield; closed by plugs (not to attach the sensor can be used) B 3 (1.18) 34 (1.34) Three mounting holes M4x5 at the three levels A, B, C Fig. 11 Dimensional drawing LLT27xx-5, connectors on the rear side, dimensions in mm, not to scale Every three mounting holes M4x5 on three levels A, B, C Page 26

27 Mounting Standard measuring range Extended measuring range 34.5 laser line 2 extended measuring range extended measuring range sensor field of view 21 Fig. 12 Measuring field assignment LLT27xx-5, dimensions in mm, not to scale 26 Every three mounting holes M4x5 on three levels A, B, C Page 27

28 Mounting C optically effective: max. ø1 optically effective: max. ø A ø ±1 12 ø R R x thread M4 for protection shield mounting; not for mounting the sensor B 3 34 Three mounting holes M4x5 on each layer A, B, C ø8 Fig. 13 Dimensional drawing LLT27xx-1, dimensions in mm, not to scale Every three mounting holes M4x5 on three levels A, B, C Page 28

29 Mounting Ø8 M4 5 deep A C Fig. 14 Dimensional drawing LLT27xx-1, connectors on the rear side, dimensions in mm, not to scale Every three mounting holes M4x5 on three levels A, B, C B Page 29

30 Mounting laser line 2 extended measuring range extended measuring range sensor field of view Standard measuring range Extended measuring range Fig. 15 Measuring field assignment LLT27xx-1, dimensions in mm, not to scale Page 3

31 Mounting 5.2 Connections laser on state 1394/ethernet 1394/ethernet RS VDC 24 VDC RS422 LLT27x, rear side Fig. 16 Output sockets arrangement LLT27x, top side The sensors are available in two versions: Sockets on the top side or on the rear side. Page 31

32 Mounting Power Supply Connector 24 VDC, see Fig. 16 Range: VDC (rated value 24 VDC); maximum current 5 ma Cable shield is connected to connector case and should be connected using the protective earth connector PE of the main power supply. The power cable PC is recommended. Pin No. Assignment Standard Color PC27; old version in ( ) Options 52, 53, 54, 55 Color PC27(2) 1 24 V+ white (red) 24 V+ pink 2 Laser help n.c. LH+ gray n.c. 3 Laser on/off n.c. Laser off+ yellow 4 Laser on/off n.c. Laser off- green n.c. 5 Laser help n.c. LH- brown 6 GND brown (black or blue) 24 V GND white Fig. 17 Pin assignment 6-pole power connector, 24 VDC External Laser Switching, see Chap , too View on solder pin side, male cable connector, counting direction anticlockwise Page 32

33 Mounting RS422, Synchronization, Switching Signals Connector RS422, see Fig. 16. The RS422 port can be used with either of the following configurations. RS422: Programs can be loaded with a PC and measurement results transmitted via the RS422 interface. However, the lower data rate allows only lower measuring rates than Ethernet connection. Synchronization / triggering: The RS422 port is used for synchronization and triggering using switch signals. All switching signals are potential-separated. PIN No. Assignment RS422 General 9-pol. Sub-D 1 1 Rx+ Ch Rx- Ch GND1 5 3 Tx+ Ch2+ 9 View on solder pin side, male 4 Tx- Ch2-1 cable connector, counting direction anticlockwise 6 GND2 5 Fig. 18 Pin assignment 6-pole RS422 connector The PIN numbers refer to the unit. Micro-Epsilon recommends the use of the interface cable SC RS422 from the optional accessories. 1) Optional RS422 interface cable (SC27-4,5RS422) from Micro-Epsilon, compatible to the RS422 to USB converter. The pins 4, 6, 7 and 8 are not connected. All outputs or inputs are designed symmetrically and wired with 12 Ohm internal terminating resistors. The signals must be operated symmetrically. Page 33

34 Mounting Changeover Transmit / receive Changeover Transmit / receive Rx Tx Rx Tx Isolation Ch1+ 12 Ohm Ch1- GND1 Ch2+ 12 Ohm Ch2- GND2 Pin RS422 connector Fig. 19 RS422 internal circuitry (switching signals) All switching signals are built in the same way. The programming specifies the assignment as inputs or outputs. The switching circuits used have internal potential isolation. No potential isolation between 24 V supply ground and internal circuitry, see Fig. 19 (left side). A ground connection (GND1 and GND2) is assigned to each channel. The ground connections are connected with each other and must be connected with the ground connector of a synchronization/trigger source or a serial device. The channels Ch1 and Ch2 can be used for the following functions: Serial interface RS422 in duplex or simplex mode (Rx and Tx). Synchronization: Using the synchronization signals, several sensors can be synchronized with each other or individual profiles (scans) can be triggered. Page 34

35 Mounting Optional additional functions (trigger, encoder). External wiring must be performed according to the RS422 standard. Primarily use RS422 driver circuits or converters. Alternatively use devices with RS422 connectors, e.g. sensors, encoders or SPC s. Channel settings Interface function (operating mode) Function Ch1 Function Ch2 Serial communication (RS422) 1 RX TX External synchronization Sync In Sync Out Triggering Trigger IN Trigger OUT Synchronizing several sensors with each other: Connect the output Ch2+ (Pin 3) of sensor 1 with the correct polarity to the input Ch1+ (Pin 1) of sensor 2. Connect the output Ch2- (Pin 4) of sensor 1 with the correct polarity to the input Ch1- (Pin 2) of sensor 2. Also connect both the GND1 pins (Pin 5) of the sensors to each other. The cable connection must preferably be made using a shielded, twisted-wire cable whereby the cable shield is connected to the connector cases. The sensor 1 as master then synchronizes sensor 2. 1) Default settings Use a shielded cable; connect the shield to the connector case. Use a cable with twisted wires. Use the recommended interface cable RS422. Page 35

36 Mounting Ethernet Connection The Ethernet connection is the standard connection to the PC for all current scancontrol 27xx models. The sensor supports the transmission at 1 Mbit/s and 1 GBit/s. We recommend the Ethernet connection cable SC27-5/ET or another length included in the optional accessory, see Chap. A 1.2, for the Ethernet connection. For the power supply a corresponding voltage, see Chap. 3.2, has to be connected to the socket 24 VDC. Due to a high data rate, we recommend using a high-quality Ethernet PC plug-in card, for example Intel- Pro/1 PT. The sensors are to be preferably connected directly to the network connection or by means of a high-quality switch. As a hub would result in a massive data collision it cannot be used. The PC should have one or more network cards only for the sensors. The operation of the sensor via Ethernet does not require any driver installation. However, the network settings have to be done correctly: If more network cards are used, they have to belong to different networks, for example different Class-Csub networks, however they may not belong to the same Class-B sub network. The sensors are supported by an automatically, sensor-adapted IP address in the link-local-net ( x.x). No collision testing is effected. This is the standard setting, too. The sensor supports the DHCP protocol. This setting is activated by default and has priority over the retrieval in the link-local-net. A fixed IP address can be given. Various network settings can interfere the connection to the sensor (fo example Firewall or packet filter). We recommend using a packet size of 124 Bytes/packet (payload) which can be set in the demonstration program or the sensor SDK. Page 36

37 Mounting RJ45 connector 8-pin. connector The PIN numbers refer to the scan- PIN no. Color stranded PIN no. 1BaseT, 1BaseT CONTROL 27x unit. 1 hook-up wire white (orange) 5 1BaseTX Tx+ D1+ Micro-Epsilon recommends using the ethernet connection cable 2 orange 6 Tx- D1- SC27-5/ET from the optional accessories, see Chap. A white (green) 8 Rx+ D2+ 4 blue 1 D3+ 5 white (blue) 2 D3-6 green 7 Rx- D2-7 white (brown) 3 D4+ 8 brown 4 D View: pin side male cable connector View on solder pin side, ODU Page 37

38 Mounting External Laser Switching Series LLT27-x(2), LLT27-x(3), LLT27-x(4), LLT27-x(5), LLT27-x(52), LLT27-x(53), LLT27-x(54) and LLT27-x(55) sensors offer this function. Assignment options 2, 3, 4, 5, 52, 53, 54 and 55 PIN No. Color PC27(2) V+ pink LH+ grey 3 Laser off+ yellow Laser off- green View on solder pin side, male 5 LH- brown cable connector, counting 6 24V GND white direction anticlockwise Fig. 2 Pin assignment 6-pole power connector, 24 VDC i Sensors of laser class 3B (IIIB) need an external key switch to switch off the laser. Use a serial key switch inside the control circuit to switch off the laser. Type Type 2 TTL o. HTL Laser off: U OUT <.8 V Laser on: 2.8 V < U OUT < 31 V U OUT 3 Fig. 21 Options to power off the laser Type Type V + LH+ LLT27 PNP typ. 4mA 3 3 max. 31 V 4 4 NPN LH- 24V GND Power connector 24 VDC Page 38

39 Mounting If the voltages between pin 3 and pin 4 are <.8 V, the laser is off. The external laser switching is a hardware solution and has the highest priority. The laser can also be disabled by software. 5.3 Installation Instructions The operating voltage can be supplied via a separate power source. Power supply via the Ethernet connection (PoE) is not permitted. The operating voltage is protected against reverse polarity. The operating voltage for the measuring device should come from a 24 V power supply which is only used for measuring equipment and not simultaneously for drives, contactors or similar pulse interference sources. Only use shielded cables for all connection cables. Connector and cable must be matched to each other for hermetically sealed versions. Paired data cables with colored cores and copper shielding are recommended for self-made cables. Connect the cable shields to the potential equalization on the evaluation unit (switch cabinet, PC case, connector case) and avoid ground loops. Lay all connection cables in accordance with the generally applicable measuring technology regulations, i.e. for example not directly next to pulse-carrying lines, preferably in a separate cable duct. The minimum bending radii of the recommended cables for flexible laying must not be less, see Fig. 22. MICRO-EPSILON recommends the use of the optionally available power supply PS22, DIN rail mounting, input 23 VAC, output 24 VDC/2.5 A. Page 39

40 Mounting 5.4 Recommended Connector and Cable Types Female connector Connector characteristics Connector type 1 (see standard equipment) Cable diameter 2 Bending radius (min.) 24 VDC ODU MiniSnap, Series B, size 1, S31BAC-P6MFG-5 or 4.8 mm or 35 mm hermetically sealed version S31BAC-P6MFG mm (IP 68), 6-pole, coding A (3 ), solderable RS422 ODU MiniSnap, Series B, size 1, S31BQC-P6MFG mm 4 mm hermetically sealed version (IP 68), 6-pole, coding Q (12 ), solderable Ethernet ODU MiniSnap, Series B, size 1, hermetically sealed version (IP 68), 8-pole, coding J (9 ), solderable Connector mounted on the cable SC27-5/ET 7 mm 84 mm Fig. 22 Recommended connector and cable types 1) Manufacturer: ODU Steckverbindungssysteme GmbH & Co. KG, D Mühldorf/Inn, 2) Applies for recommended cable, see Chap. A 1.1. Using the plug connector characteristics, see Fig. 22, other connector types (angled connectors or cable parts) can also be ordered from the manufacturer. i Use connectors with chucks accordingly to the cable diameter. Page 4

41 Mounting 5.5 Mounting the Connectors Mount the cylindrical connectors according to the manufacturer s instructions. Further information you will find in the catalog of the manufacturer ( >> ODU MINI-SNAP >> Download >> MINI-SNAP Series LKB ). 5.6 Getting Ready for Operation, Commissioning Mount the sensor according to the installation instructions. Connect the sensor to the computer or the controller using the Ethernet cable. Connect the sensor to downstream display or monitoring units and to the power supply if necessary. The connectors for the operating voltage, switching signals and Ethernet are fitted with push-pull locking. Pull apart at the grip to release the connection. Connect the shield of the power supply cable to the PE protective earth conductor of the main power supply. Close plug-in connections not needed with the supplied protective caps for ODU sockets, see Chap Switch on the power supply. The sensor must only be connected to the peripheral equipment when disconnected from the power supply, i.e. only when the operating voltage is switched off. Page 41

42 Operation of the Sensor with a PC 6. Operation of the Sensor with a PC 6.1 Displays After getting ready for operation, switch on the external direct current power supply (24 VDC). The state LED indicates different error conditions by flashing. If several errors occur at the same time, it indicates two of them alternately. Therefore the LED can continue to flash for some time after the rectification of an error. If no flashing occurs for several seconds, no error has occurred. The sensor needs a running-in time of typically 2 minutes for high precision measurements. i 6.2 Operating and Demonstration Programs A CD-ROM is provided for the operation of the sensor: As well as the installation instructions mentioned above, the CD-ROM also contains various documentation and programs: The demonstration program DeveloperDemo.exe in the directory [CD]:\Program\Developer Demo is used for scanner parameterization and simple display of profile data. A screenshot of the standalone demonstration program can be seen, see Chap The directory [CD]:\Development\SDK contains a sensor-specific DLL and descriptions and examples for creating your own user programs with the C++ programming language. It can also be used with C, Delphi or other programming languages. The associated descriptions for the DLL in German and in English can be found in the same directory. scancontrol Configuration Tools is used to analyze typical measurement tasks for. scancontrol 3D-View visualizes three dimensional point data, which are recorded with. The measuring fields, see Chap , are partially used in the demonstration programs. Page 42

43 Operation of the Sensor with a PC 6.3 Installation and Requirements Requirements The following minimum system specification is necessary for the operation of the scancontrol software packages: Windows 7 (32 bit and 64 bit), Windows 8 or 8.1 (32 bit and 64 bit), Windows 1 (32 bit and 64 bit) 1-GHz or faster (32 bit and 64 bit) processor / 1 GB RAM Screen resolution: 124x Installation To be able to use the software the following steps must be followed: 1. Install the software according to the instructions on the CD. 2. Connect the scancontrol measuring system to the computer via Ethernet. In order to connect scancontrol via Ethernet to the PC, proceed as follows: Finish the installation of the scancontrol software packages completely. Connect scancontrol via the Ethernet interface to the PC and switch on the power supply. Please wait until the device is recognized by the PC. This may take a few seconds. The system is now ready to operate the scancontrol measurement system with the scancontrol software packages. i Connect scancontrol directly with the PC. Do not use hubs or switches. Page 43

44 Operation of the Sensor with a PC 6.4 Instructions for Operating Measuring Field Selection The optical design of the sensor satisfies the so-called Scheimpflug condition which ensures optimum mapping over the complete measuring range. In doing so, the measuring range is mapped on a rectangular matrix. The distortions resulting from this are shown, see Fig. 23. The usable measuring range is always trapezoidal. The assigned maximum x-values for the z-coordinates can be found, see Fig. 9, see Fig. 12, see Fig. 15. Please refer to the sensor acceptance report of your sensor. A slight range shifting of a measuring field is possible and depends on the sensor. The top edge corresponds to the start of the measuring range and the bottom edge to the end of the measuring range. The corners of the read image field are on a grid with grid spacing of 1/8 of the matrix. An image field change is only possible in this raster. The sensor matrix used in the supports the reading of a restricted measuring field. The following picture shows the predefined view areas and the associated measuring fields. Page 44

45 Operation of the Sensor with a PC Fig. 23 Supported measuring fields Page 45

46 Operation of the Sensor with a PC The measuring field can be restricted by omitting complete matrix areas in order to suppress interfering image ranges. No correlation of the measuring field size to the speed of the reading process can be made. The following measuring fields are used in the demonstration program, see Chap Name Index Large Standard 2 Small 7 Fig. 24 Measuring fields used Measuring field and measuring range must be clearly differentiated in practical use. The measuring field is related to the matrix and the measuring range is related to the measuring object (the object space). Both do not have to match on account of the optical mapping and the definitions. The measuring field Standard is larger than the measuring range Standard. The minimum dimensions can be found, see Fig. 9, see Fig. 12, see Fig. 15. i The sensors are distinguished by a laser line with 2 opening angle. the receiver has a smaller opening angle (view angle) than the laser line. centered measuring field (symmetrical to the center axis). the high resolution sensor image matrix has 64 x 48 pixels. The measuring field geometry is fixed. reference for the distance (Z-axis) is the lowest body edge of the sensor, see Fig. 9, see Fig. 12, see Fig. 15. Use of the DCAM standard 1.3, however with rededication of the parameters: camera parameter in triangulation parameters image in profile Further information for this can be found in the file OpManPartB.html on the CD-ROM. Standard digital video camera driver according to DCAM 1.3 from different manufacturers can be used. Page 46

47 Operation of the Sensor with a PC Calibration The calibration of the sensor is performed using the complete matrix and is independent from the selected measuring field. The trapeze form of the measuring field is produced from the projection onto the sensor matrix. The standard measuring range is framed in the center. A sensor acceptance report is enclosed for each sensor. Three diagrams for the linearity measurement which are briefly explained in the report are included in the sensor acceptance report. The key diagram in the sensor acceptance report is shown again below, see Fig. 25. Points with a deviation >.5 mm 8 9 Extended measuring range Distance z [mm] 1 11 Standard measuring range Midrange Position x [mm] Fig. 25 Linearity deviation of an LLT27-25 The black points show the places where the measurement error exceeds the linearity limit of.5 mm. The picture on the top left and bottom right in the acceptance report show sections through the picture, see Fig. 25 (blue lines). Page 47

48 Operation of the Sensor with a PC All measuring points in the center of the measuring range (vertical section where x=) and bottom right of the horizontal section, also in the (vertical) center of the measuring range (midrange) are shown on the top left of the acceptance report. The measurement error increases at both ends of the depth range and particularly in the remote corners. These areas should therefore be avoided for the measurement Automatic Exposure Time Regulation The automatic exposure time regulation facilitates the recording of the profile with optimum exposure time (shutter time). The available brightness information for each point of the profile is used for this. The shutter time preset by the user is used as the starting value for the automatic exposure time regulation. It should be selected so large that still valid measured values can be output at the darkest place of the profile. One of the supplied demonstration programs can be used for determining this. The automatic exposure time regulation can also be deactivated if required. If there is no object in the measuring range, the shutter time stored in the shutter register of the sensor will be used as exposure time. This value must also guarantee reliable recognition of the darkest measurement object. A previous test is recommended if the target is very dark or has very high contrast. The various demonstration programs are suitable for adjusting and testing the exposure time. In doing so, it is by all means sensible to work with several different exposure times and to observe the effect in the diagrams. The current exposure time can be calculated from the timestamps of the measured values. It is displayed as Shutter time, see Fig. 26. Page 48

49 Operation of the Sensor with a PC Shutter time preset by the user:.1 ms Automatic shutter time is active Result: Sensor operates with a shutter time of.16 ms Fig. 26 Screenshot of the developer demonstration program with automatic shutter Page 49

50 Operation of the Sensor with a PC 6.5 Error Influences Reflection Factor of the Target Surface The sensor basically evaluates the diffuse portion of the laser line reflections. Any statement about a minimum reflection factor is only possible with reservations. A preliminary examination is necessary for using the sensor on transparent or reflecting objects. The method of direct reflection on reflecting surfaces as it is successfully applied for the point triangulation cannot be used for the line triangulation on account of the fan-shaped form of the laser line (central projection). Here, the receiving lens would only be able to reach a narrow area near the center. As usually curved surfaces should also be measured for the profile measurement, this range will be further narrowed Color Differences Color differences of measurement objects have effects. However, these color differences are often also combined with different penetration depths of the laser light into the material. Different penetration depths in turn result in apparent changes of the line thickness. Therefore, color changes, combined with penetration depth changes, can result in inaccurate measurements. As the exposure parameters can only be changed as a whole for one profile, careful matching of the exposure to the target surface is recommended Temperature Influences A running-in time of at least 2 minutes during start-up is required in order to achieve a uniform temperature spread in the sensor. If measurements with accuracy in the μm range are made, the effect of temperature fluctuations on the mounting must also be observed by the user. Due to the damping effect of the thermal capacity of the sensor, fast temperature changes are only measured after a delay. Page 5

51 Operation of the Sensor with a PC External Light An interference filter in the sensor is present for suppression of external light. In general, the shielding of external light directly emitted on the target or reflected in the sensor must be ensured using protective covers or similar. Pay particular attention to unwanted reflections of the laser line outside the measuring object range (background, object holder or similar) which can be reflected back again into the view area of the receiver. Matt black surface coatings are recommended for all objects outside the measuring range (object holders, transport apparatus, grippers or similar) Mechanical Vibrations If high resolutions in the μm range should be achieved with the sensor, particular attention must be paid to stable or vibration-damped sensor and measuring object mounting Surface Roughness Surface roughness of 5 μm and more results in surface noises due to interference of the laser light. Direct reflections of the laser light to the receiver can also occur at the finest grooves (e.g. abrasion marks on the surface) particularly if these run in the line direction. This can result in inaccurate measured values. Prevention of this effect might be possible by adjusting several sensor settings e.g. exposure time, filter. Page 51

52 Operation of the Sensor with a PC Shadowing Effects Receiver: The laser line can disappear completely or partially behind steep edges. The receiver then does not see these areas. Laser line: The fan-shaped form of the laser line inevitably results in partial shadowing at vertical edges. In order to make these areas visible, only changing the sensor or object position helps. As a general rule, measuring objects with steep edges cannot be one hundred percent measured using laser triangulation. The missing areas can only be supplemented or interpolated using suitable software. Shadowing of the receiver Shadowing of the laser line Fig. 27 Shadowings Page 52

53 Operation of the Sensor with a PC 6.6 Cleaning A periodically cleaning of the protective housings is recommended. Dry cleaning This requires a suitable optical antistatic brush or blow off the panels with dehumidified, clean and oil free compressed air. Wet cleaning Use a clean, soft, lint-free cloth or lens cleaning paper and pure alcohol (isopropanol) for cleaning the protective housing. Do not use commercial glass cleaner or other cleansing agents. Page 53

54 scancontrol Output Unit 7. scancontrol Output Unit The measurement system scancontrol 271 measures and evaluates profile data of a measurement target and supplies analog and digital control signals. scancontrol Output Unit outputs digital and analog signals, is based on the WAGO -I/O-System 75 uses Ethernet. Setup and operation of scancontrol Output Unit are exemplarily described below. 7.1 scancontrol Output Unit - Components Output Unit Basic consisting of Ethernet Fieldbus Coupler with System Supply (OU-Fieldbus Coupler/Ethernet) 24 VDC Power Supply Filter (OU-Filter module) and End Module (OU-Bus-termination module) Digital output module Analog output module X 1 X 2 8 ON 1 24V X3 V ON : WBM 255: DHCP ETHERNET LINK ACT 1 LINK ACT 2 MS NS I/O OU Fieldbus Coupler A B Ñ C D Status voltage supply - Power jumper contacts - System Data contacts System supply (OUT) 24 V V Supply via power jumper contacts 24V V OU-Filter module System supply (In) 24 V V Power jumper contacts Status DO 1 DO 7 DO 1 DO 3 DO 5 DO A1 A2 A3 A4 A5 A6 A7 A8 Status DO 2 DO 8 Data contacts DO 2 D 4 D 6 DO 8 Function Error AO 1 V AO 3 V A1 A2 Power jumper contacts Power jumper contacts Digital output module Analog output module 75-6 Bus termination A B M M A3 A4 M M C D AO 2 V AO 4 V Data contacts Fig. 28 Example configuration Ethernet with an analog output module and a digital output module A B C D Page 54

55 scancontrol Output Unit The components of a scancontrol Output Unit have to be mounted on a top hat rail (TS35) in the described order. Without using a top hat rail a robust installation cannot be guaranteed. Ensure that each module is locked securely on the top hat rail. The bus has to be terminated with the bus termination, see Fig. 28. Each module of scancontrol Output Unit is described, see Chap Further informations can be found in the data sheet and manual of the respective module in the supplied scancontrol Software CD. 7.2 Connect the Supply Voltage L1 L2 L3 N PE 8 ON 1 24V X3 V X 1 ON : WBM 255: DHCP ETHERNET LINK ACT 1 LINK ACT 2 MS NS I/O A B D + Ñ C OU-Filter module Digital output modules need a field supply of 5 VDC or 24 VDC depending on the module type. X V OU Fieldbus Coupler System supply V 23 V 24 V Field supply Fig. 29 Separated power units for system and field supply (Ethernet) Page 55

56 scancontrol Output Unit After mounting of the modules, the required wiring has to be installed: Connect the System supply (out) terminals of the OU-Filter module to the System supply (in) terminals of the OU-Fieldbus Coupler ( V and 24 V, see Fig. 29). i Connect the system supply (in) of the OU-Filter module to the power supply ( V and 24 V, see Fig. 29). Connect the field supply (in) of the OU-Filter module to the power supply ( V and 5 V/24 V, see Fig. 29). The system supply and field supply should be separated to ensure the bus operation and electrical isolation in case of a short-circuit of an actor. 7.3 Commissioning scancontrol Output Unit After having installed the required wiring of the modules of scancontrol Output Unit, you have to parameterize the measurement system according to your measurement task to get the desired signals at the digital and analog output ports. Connect the sensor to the PC using the supplied Ethernet cable. Alternatively, scancontrol Output Unit can be connected simultaneously to the PC and to the sensor. Parameterize the measurement system using scancontrol Configuration Tools and assign the desired signals to the digital and analog output ports. When the parameterization is finished, save the settings to a user mode of the sensor. scancontrol Configuration Tools > Menu > Parameters > Save parameters to scancontrol.. Refer to scancontrol Configuration Tools manual, Chapter Exit scancontrol Configuration Tools and disconnect scancontrol 271, PC and if necessary scancontrol Output Unit. Connect the scancontrol 271 to the Output Unit using the supplied Ethernet cable. The sensor and the output unit operate now as an independent measurement system and the digital and analog signals are output via the assigned ports. Page 56

57 scancontrol Output Unit 7.4 Specification of the Components Output Unit Basic (Ethernet) Micro-Epsilon order No Consists of OU-Fieldbus Coupler/Ethernet OU Filter module OU-Bus termination module Interfaces: 2x Ethernet to connect scancontrol 271 sensors. Indicators (state LED s, for detailed description refer to the manual of the Ethernet Fieldbus Coupler) The System Supply is already mounted to the Ethernet Fieldbus Coupler. Fig. 3 OU-Fieldbus Coupler/Ethernet with power supply module Page 57

58 scancontrol Output Unit System data Max. number of bus sharing unit Limited by Ethernet specification Max. length of fieldbus segment 1 m Baud rate 1/1 Mbit/s Technical data No. of I/O modules 64 with bus extension 25 Voltage supply DC 24 V (-25 % %) Max. input current 28 ma at 24 V Internal current consumption 45 ma at 5 V Total current for I/O modules 7 ma at 5 V Voltage drop at I max. < 1 V at 64 I/O modules Fig. 31 Technical data Fieldbus Coupler/Ethernet Supported Modules 8-Channel digital output module; DC 24 V;.5 A; high-side switching; 8 actors; short-circuit-proofed; Micro-Epsilon order no , see Chap ; power supply through power jumper contacts 8-Channel digital output module; DC 24 V;.5 A; low-side switching; 8 actors; short-circuit-proofed; Micro- Epsilon order no ; power supply through power jumper contacts 4-Channel analog output module; - 1 V; Micro-Epsilon order no , see Chap Channel analog output module; ±1 V; Micro-Epsilon order no Channel analog output module; 2 ma; Micro-Epsilon order no Channel analog output module; 4 2 ma; Micro-Epsilon order no Page 58

59 scancontrol Output Unit OU-DigitalOut/8-Channel/DC24 V/.5 A/High-side Switching/8 Actuators Fig Channel digital out module Micro-Epsilon order No The 8-channel digital output module DC 24 V.5 A is short-circuitproofed, high-side switching, for TS35, CAGE CLAMP -Connection (8 actuators) The field level is galvanically isolated to the system level The indicators (state LED s) additionally show the status of the digital output ports (IO/NIO), for detailed description refer to the manual of the 8-channel digital output module DC 24 V.5 A, 8 actuators, high-side switching For each digital port actuators can be directly wired via DO 1/2/3/4/5/6/7/8. scancontrol 271 supports eight digital outputs Number of outputs 8 Current consumption (internal) 25 ma Voltage via power jumper contacts DC 24 V (-25 % / + 3 %) Type of load resistive, inductive, lamps Switching rate max. 2 khz Output current.5 A short-circuit-proofed Energy dissipation W max. (unique switching off) Current consumption typ. (field side) Fig. 33 Technical data of the digital output module.9 J L = 2 W /I² max. max. 15 ma (per module) + load Page 59

60 scancontrol Output Unit OU-AnalogOut/4-Channel/-1 V Micro-Epsilon order No channel analog output module DC -1 V Indicators (state LED s, for detailed description refer to the manual of the 4-channel Analog Output Module DC -1 V) The voltage range of the module is restricted to -1 V and can not be extended by changing the appropriate setting in scancontrol Configuration Tools. The output signal is output galvanically isolated to the system level. The resolution of this module is limited to 12 bit. scancontrol 271 supports four analog outputs Fig channel analog out module Number of outputs 4 Voltage supply via system voltage DC/DC Signal voltage... 1 V Load impedance > 5 kω Resolution 12 Bit Conversion time typ. 1 ms Output filter settle time typ. 1 µs Measurement error at 25 C <±.1 % of full scale output Temperature coefficient <±.1 %/ K of the full scale value Fig. 35 Technical data of the analog output module Page 6

61 Warranty 8. Warranty All components of the device have been checked and tested for perfect function in the factory. In the unlikely event that errors should occur despite our thorough quality control, this should be reported immediately to MICRO-EPSILON. The warranty period lasts 12 months following the day of shipment. Defective parts, except wear parts, will be repaired or replaced free of charge within this period if you return the device free of cost to MICRO-EPSILON. This warranty does not apply to damage resulting from abuse of the equipment and devices, from forceful handling or installation of the devices or from repair or modifications performed by third parties. No other claims, except as warranted, are accepted. The terms of the purchasing contract apply in full. MICRO-EPSILON will specifically not be responsible for eventual consequential damages. MICRO-EPSILON always strives to supply the customers with the finest and most advanced equipment. Development and refinement is therefore performed continuously and the right to design changes without prior notice is accordingly reserved. For translations in other languages, the data and statements in the German language operation manual are to be taken as authoritative. Page 61

62 Service, Repair 9. Service, Repair In the case of a defect on the : If possible, save the current sensor settings in a parameter set, see Configuration Tools, menu / parameters / Save parameters to scancontrol, in order to load the settings back again into the sensor after the repair. Please send us the effected parts for repair or exchange. In the case of faults the cause of which is not clearly identifiable, the whole measuring system must be sent back to: MICRO-EPSILON Optronic GmbH Lessingstraße Dresden - Langebrück / Germany Tel. +49 () 3521 / 729- Fax +49 () 3521 / mail to: optronic@micro-epsilon.de 1. Decommissioning, Disposal Disconnect all cables between the sensor and the following control or evaluation units. Incorrect disposal may cause harm to the environment. Dispose of the device, its components and accessories, as well as the packaging materials in compliance with the applicable country-specific waste treatment and disposal regulations of the region of use. Page 62

63 Error Codes 11. Error Codes LED error lights for long time, LED error lights briefly Flashing sequence Cause Remedy Notes.. 2x short..- 2x short, 1x long 3x short. 4x short 2x long. 2x long, 1x short.. 2x long, 2x short Group: Loading / saving configuration Mode not found Select different one only previously stored modes can be called up Write error flash Contact manufacturer, return should not occur in sensor normal operation Flash full none, contact manufacturer should not occur in normal operation Loading suppressed due to active data transmission Stop active data transmission Group: Data processing and transmission Data overflow in the sensor Data overflow during receipt of the data from the sensor Data overflow for serial port RS422 Select smaller measuring field, reduce profile frequency, select less complex measuring program Select smaller measuring field, reduce profile frequency, select less complex measuring program Reduce profile frequency, select less complex measuring program prevents PC software crashes; however, mode number will continue to be counted Data can be impaired; exposure time can be longer than expected Data can be impaired Data can be impaired Page 63

64 Error Codes Flashing sequence Cause Remedy Notes 2x long, 3x short.. 2x long, 5x short 2x long, 6x short - 3x long -. 3x long, 1x short -.. 3x long, 2x short x long, 3x short 4x long Group: Data processing and transmission Data overflow during Reduce profile frequency transmission of the data Error during calculation Reduce profile frequency, select faster calculation mode Error during transmission Reduce profile frequency Group: Output Unit scancontrol Output Unit not found Connected modules of scancontrol Output Unit are not supported Communication error (scancontrol Output Unit) Output overflow (scan- CONTROL Output Unit) Connect the sensor with the - scancontrol Output Unit Use the supported modules only, see Chap Reduce profile frequency Reduce profile frequency Group: Ethernet interface IP address conflict Check the Ethernet configuration of device and the host PC Choose another IP address for the device Data can be impaired Data can be impaired Data can be impaired - - If the problem persists, please contact the manufacturer The state LED flashes green; long during active data transmission and short for controller accesses. A controller access can cause various data overflows particularly if the measuring frequency is near its maximum. Page 64

65 Anhang Accessories Appendix A 1 A 1.1 Accessories Recommended Accessories PS22 Power supply PS22, power supply for DIN rail mounting, input 23 VAC, output 24 VDC/2.5 A SC27-X/ET Ethernet connection cable X m; optional lengths: X = 2 m, 5 m, 1 m, 15 m, 2 m. With mounted ODU round connector and 8-pin Ethernet cable connector RJ45. Version compatible for cable carriers also available. Page 65

66 Anhang Accessories A 1.2 Optional Accessories PC ~12 (.47) ~46 (1.81) Power supply cable, 4.5 m long SC27-4.5/RS422 SC27-.5/SYNC Connector/8-pin/ LLT27/Ethernet ~12 (.47) ~46 (1.81) RS422 interface cable, 4.5 m long; with mounted ODU round connector and 9-pin D-SUB cable socket, fits converter from RS422 to USB from MICRO-EPSILON. Synchronisation cable for two scancontrol 27 sensors Connector for Ethernet socket for scancontrol series 27xx Page 66

67 Anhang Accessories Connector/6-pin/ LLT27/power supply Connector for power supply socket for scancontrol series 27xx Connector/6-pin/ LLT27/RS422 Connector for RS422 socket for scancontrol series 27xx PS27 Power supply unit for scan- CONTROL 27 Suitcase scancon- TROL 26/27/29 MR 1-1 Transport suitcase for scan- CONTROL sensors, inclusive measuring stand Page 67