DV280FBM-NB0 Product Specification. Rev. 0

Size: px

Start display at page:

Download "DV280FBM-NB0 Product Specification. Rev. 0"

Dayna Preston
5 years ago
Views:

1 PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF BOE DT AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE DT AND MUST BE RETURNED TO BOE DT UPON ITS REQUEST TITLE: DV28FBM-NB Product Specification Rev. Approved by Date BEIJING BOE DISPLAY TECHNOLOGY PRODUCT GROUP TFT LCD REV. B ISSUE DATE of 28 B2-82-O (/3) A4(2 X 297)

2 TFT LCD O REVISION HISTORY REV. ECN NO. DESCRIPTION OF CHANGES DATE PREPARED - Initial Release Song yongzhi B2-82-O (2/3) DV28FBM-NB Product Specification 2 of 28 A4(2 X 297)

3 TFT LCD O Contents No ITEM Page REVISIONS HISTORY 2 CONTENTS 3 GENERAL DESCRIPTION 4. Introduction.2 Features.3 Applications.4 General Specification 2 ABSOLUTE MAXIMUM RATINGS 6 3 ELECTRICAL SPECIFICATIONS 7 3. TFT LCD Open Cell 4 INTERFACE CONNECTION 9 4. Open Cell Input Signal & Power 4.2 LVDS Interface 5 SIGNAL TIMING SPECIFICATIONS 2 5. Timing Parameters 5.2 Signal Timing Waveform 5.3 Input Signals, Basic Display Colors & Cray Scale Of Colors 5.4 Power Sequence 6 OPTICAL SPECIFICATIONS 6 7 MECHANICAL CHARACTERISTICS 8 8 RELIABLITY 9 9 PRODUCT SERIAL NUMBER 2 PACKING INFORMATION 2 HANDING & CAUTIONS 23 2 APPENDIX 24 B2-82-O (3/3) DV28FBM-NB Product Specification 3 of 28 A4(2 X 297)

4 TFT LCD O GENERAL DESCRIPTION. Introduction DV28FBM-NB is a color active matrix TFT LCD Module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This Module has a28inch diagonally measured active area with HD resolutions (366 horizontal by 256 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 6.7M colors. The TFT-LCD panel used for this Module is adapted for a low reflection and higher color type. RGB(Mini-LVDS) VDD Source Driver Circuit +2.V LVDS 5pairs CN LVDS_SEL (3pin) # 9 BIST_ # 27 Timing Controller [LVDS Rx & Mini-LVDS Tx integrated] Power Circuit Block Gate Driver Circuit G G256 S S366 TFT - LCD Panel (366 RGB 256 pixels).2 Features LVDS interface with pixel / clock High-speed response Low color shift image quality 8-bit color depth, display 6.7M colors High luminance and contrast ratio, low reflection and wide viewing angle DE (Data Enable) only mode ADS technology is applied for high display quality RoHS compliant B2-82-O (3/3) DV28FBM-NB Product Specification 4 of 28 A4(2 X 297)

5 TFT LCD O Application TFT-LCD Display for traffic and financial industry Display Terminals for diversified information High Definition Monitor (HD) AV application Products.4 General Specification < Table. General Specifications > Parameter Specification Unit Remark Active area mm Number of pixels 366 X 256 pixels Pixel pitch um Pixel arrangement RGB vertical Strip Display colors 6.7M(8bits-true) colors Display mode ADS Outline Dimension 73.2(H) 65.4(V).8(D) mm Mech Weight TBD Kg Power Consumption 26 Watt Surface Treatment Haze 25% B2-82-O (3/3) DV28FBM-NB Product Specification 5 of 28 A4(2 X 297)

2. ABSOLUTE MAXIMUM RATINGS PRODUCT GROUP REV ISSUE DATE TFT LCD O 24.6.26 The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit.

6 2. ABSOLUTE MAXIMUM RATINGS PRODUCT GROUP REV ISSUE DATE TFT LCD O The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. LCD Open Cell Electrical Specifications > [VSS=GND=V] Parameter Symbol Min. Max. Unit Remark Power Supply Voltage VDD VSS V Ta = 25 Operating Temperature T OP +5 T SUR +6 Storage Temperature T ST Operating Ambient Humidity Hop 8 %RH Storage Humidity Hst 8 %RH Note Note : Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 max. and no condensation of water. B2-82-O (3/3) DV28FBM-NB Product Specification 6 of 28 A4(2 X 297)

TFT LCD O 24.6.26 3. ELECTRICAL SPECIFICATIONS 3. TFT LCD Open Cell < Table 3.

2 V Unit Power Supply Ripple Voltage VRP 3 mv LVDS Interface CMOS Interface Power Supply Current IDD - 3 55 ma Power Consumption PDD 3.6 6.

7 TFT LCD O ELECTRICAL SPECIFICATIONS 3. TFT LCD Open Cell < Table 3. LCD Open Cell Electrical Specifications > [Ta =25± 2 ] Parameter Symbol Values Min Typ Max Power Supply Input Voltage VDD V Unit Power Supply Ripple Voltage VRP 3 mv LVDS Interface CMOS Interface Power Supply Current IDD ma Power Consumption PDD W Remark Note Rush current IRUSH A Note 2 Differential Input High Threshold Voltage Differential Input Low Threshold Voltage VRTH + +3 mv VRTL -3 - mv Common Input Voltage VLVC..2.4 V Input High Threshold Voltage Input Low Threshold Voltage VIH V VIL -.6 V Note : The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VDD=2.V, Frame rate f V =6Hz and Clock frequency = 75.4MHz. Test Pattern of power supply current a) Typ : Mosaic 8 x 6 Pattern(L/L255) b) Max : Skip H2V Sub Dot Pattern(L/L255) Note 2 : The duration of rush current is about 2ms and rising time of Power Input is ms(min) B2-82-O (3/3) DV28FBM-NB Product Specification 7 of 28 A4(2 X 297)

8 TFT LCD O LED Converter < Table 4. LED Converter Electrical Specifications > [Ta =25± 2 ] Parameter Symbol Condition Values Min. Typ. Max. Input Voltage VBL V Unit Note Input Current IBL V DIM =3.3V A Note Rush current IRUSH VBL= 24V A Power Consumption PBL Typical Luminance Watt B/L on/off control V ON/OFF BL ON = High V BL OFF =Low -.8 V PWM Frequency F PWM Hz PWM Level High Level V Low Level -..5 V PWM Duty D PWM - % Note 2 Life Time 3k - - Hrs Note 3 Note :The specified current and power consumption are under the typical supply Input voltage, 24V. It is total power consumption. Note 2 : High-duty = On/(On+Off) * On Off Note 3 : The life time of LED, 3,Hrs, is determined as the time at which luminance of the LED is 5% compared to that of initial value at the typical LED current on condition of continuous operating at 25 2 C. B2-82-O (3/3) DV28FBM-NB Product Specification 8 of 28 A4(2 X 297)

4. INTERFACE CONNECTION PRODUCT GROUP REV ISSUE DATE TFT LCD O 24.6.26 4. Module Input Signal & Power - Connector : IS-L3B-C23(Manufactured by UJU) or Equivalent. < Table 5.

9 4. INTERFACE CONNECTION PRODUCT GROUP REV ISSUE DATE TFT LCD O Module Input Signal & Power - Connector : IS-L3B-C23(Manufactured by UJU) or Equivalent. < Table 5. Open Cell Input Connector Pin Configuration > Pin No Symbol Description Pin No Symbol Description VDD Power Supply +2.V 6 RX+ LVDS Receiver Signal(+) 2 VDD Power Supply +2.V 7 GND Ground 3 VDD Power Supply +2.V 8 RX2- LVDS Receiver Signal(-) 4 VDD Power Supply +2.V 9 RX2+ LVDS Receiver Signal(+) 5 GND Ground 2 GND Ground 6 GND Ground 2 RCLK- LVDS Receiver Clock Signal(-) 7 GND Ground 22 RCLK+ LVDS Receiver Clock Signal(+) 8 GND Ground 23 GND Ground 9 LVDS_SEL L =JEIDA, H or NC= VESA 24 RX3- LVDS Receiver Signal(-) NC No Connection 25 RX3+ LVDS Receiver Signal(+) GND Ground 26 GND Ground 2 RX- LVDS Receiver Signal(-) 27 BIST L or NC=Free run mode, H = BIST mode 3 RX+ LVDS Receiver Signal(+) 28 NC No Connection 4 GND Ground 29 NC No Connection 5 RX- LVDS Receiver Signal(-) 3 GND Ground Notes :. NC(Not Connected) : This pins are only used for BOE internal operations. 2. Input Level of LVDS signal is based on the IEA 664 Standard. 3. LVDS_SEL : This pin is used for selecting LVDS signal data format. If this Pin : High (3.3V) or Open (NC) Normal NS LVDS format Otherwise : Low (GND) JEIDA LVDS format 4. BIST : This pin is used for selecting display pattern mode when input DE or input CLOCK quits toggling. If this Pin : Low (GND) or Open (NC) Free run mode(black Pattern) Otherwise : High( 3.3V) BIST mode(bist Pattern) Sequence : On = VDD LVDS Option, BIST Option Interface signal Off = Interface signal LVDS Option, BIST Option VDD Rear view of LCM IS-L3B-C23 (UJU) 3 BIST Pattern B2-82-O (3/3) DV28FBM-NB Product Specification 9 of 28 A4(2 X 297)

10 4.2 LVDS Interface PRODUCT GROUP REV ISSUE DATE TFT LCD O LVDS Receiver : Timing Controller (LVDS Rx merged) / LVDS Data : Pixel Data < Table 6. Open Cell Input Connector Pin Configuration > LVDS Pin Vesa Data format JEIDA Data format Remark TxIN/RxOUT Red [LSB] R2 TxIN/RxOUT Red R3 TxIN/RxOUT2 Red2 R4 TxOUT/RxIN TxIN/RxOUT3 Red3 R5 TxIN/RxOUT4 Red4 R6 TxIN/RxOUT6 Red5 R7 [MSB] TxIN/RxOUT7 Green [LSB] G2 TxIN/RxOUT8 Green G3 TxIN/RxOUT9 Green2 G4 TxIN/RxOUT2 Green3 G5 TxOUT/RxIN TxIN/RxOUT3 Green4 G6 TxIN/RxOUT4 Green5 G7 [MSB] TxIN/RxOUT5 Blue [LSB] B2 TxIN/RxOUT8 Blue B3 TxIN/RxOUT9 Blue2 B4 TxIN/RxOUT2 Blue3 B5 TxIN/RxOUT2 Blue4 B6 TxOUT/RxIN2 TxIN/RxOUT22 Blue5 B7 [MSB] TxIN/RxOUT24 HSYNC HSYNC TxIN/RxOUT25 VSYNC VSYNC TxIN/RxOUT26 DEN DEN TxIN/RxOUT27 Red6 R [LSB] TxIN/RxOUT5 Red7 [MSB] R TxIN/RxOUT Green6 G [LSB] TxOUT/RxIN3 TxIN/RxOUT Green7 [MSB] G TxIN/RxOUT6 Blue6 B [LSB] TxIN/RxOUT7 Blue7 [MSB] B TxIN/RxOUT23 Reserved Reserved B2-82-O (3/3) DV28FBM-NB Product Specification of 28 A4(2 X 297)

11 TFT LCD O LED Converter Input Signal & Power - Connector : CI4MHRL-NH (Cvilux) or equivalent < Table 7. LED Converter Input Connector Pin Configuration > Pin No Symbol Description Remarks VBL Power Supply +24V 2 VBL Power Supply +24V 3 VBL Power Supply +24V 4 VBL Power Supply +24V 5 VBL Power Supply +24V 6 GND Ground and Current Return 7 GND Ground and Current Return 8 GND Ground and Current Return 9 GND Ground and Current Return GND Ground and Current Return DET Normal (Low) / Abnormal (Open Collector) Low : ~.8V 2 VBLON/OFF Backlight ON/OFF control On : 2.4V~5.V/Off :~.8V 3 NC No Connection 4 PDIM External PWM control signal Notice: While system is turned ON or OFF, the power sequences must follow as below descriptions: Turn ON sequence: VBL PWM signal BLON Turn OFF sequence: BLOFF PWM signal VBL B2-82-O (3/3) DV28FBM-NB Product Specification of 28 A4(2 X 297)

12 5. SIGNAL TIMING SPECIFICATION 5. Timing Parameters (DE only mode) PRODUCT GROUP REV ISSUE DATE TFT LCD O < Table 8. Timing Table > ITEM Symbol Min Typ Max Unit Note CLK Hsync Vsync Horizontal Active Display Term Vertical Active Display Term Period t CLK ns Frequency MHz Period t HP t CLK Frequency f H KHz Period t VP t HP Frequency f V Hz Valid t HV t CLK Total t HP t CLK Valid t VV t HP Total t VP t HP Notes: This product is DE only mode. The input of Hsync & Vsync signal does not have an effect on normal operation. B2-82-O (3/3) DV28FBM-NB Product Specification 2 of 28 A4(2 X 297)

13 5.2 Signal Timing Waveform PRODUCT GROUP REV ISSUE DATE TFT LCD O DCLK tclk.5 VDD Valid data First data Invalid data Pixel data Pixel data Invalid data Valid data Second data Invalid data Pixel data Pixel data Invalid data DE(Data Enable) HSync thp thv DE(Data Enable) tvp VSync tvv DE(Data Enable) B2-82-O (3/3) DV28FBM-NB Product Specification 3 of 28 A4(2 X 297)

14 A4(2 X 297) B2-82-O (3/3) PRODUCT GROUP REV ISSUE DATE TFT LCD O DV28FBM-NB Product Specification 4 of Input Signals, Basic Display Colors and Gray Scale of Colors Green Brighter Darker Black Gray Scale of Green Blue Brighter Darker Black Gray Scale of Blue White Yellow Magenta Red Cyan Green Blue Black Basic Colors Red Brighter Darker Black Gray Scale of Red Darker Brighter White B6 B5 B4 B3 B2 B B G5 G4 G3 G2 G G G6 R3 R4 R5 R6 R R2 R B7 G7 R7 Black Gray Scale of White Blue Data Green Data Red Data Color & Gray Scale Input Data Signal < Table 9. Input Signal and Display Color Table >

15 TFT LCD O Power Sequence Power Supply VDD 2V.9VDD.VDD V T T2 T3 T.9VDD T.VDD T2 Interface Signal ( Input Data ) Hi-Z Active Signal Hi-Z Power Supply VBL 24V.9VBL.VBL V T4 T7.9VBL.8VBL(typ) T9 Dimming Signal PDIM V T5 T6 Valid T8 BLU ON/OFF enable ( VON/OFF ) V < Table. Sequence Table > Parameter Values Min Typ Max Units T.5 - ms T2-5 ms T ms T ms T5 - - ms T6 - - ms T7 - - ms T8 - - ms T9 - - ms T ms T - 5 ms T2 - - s Notes: Back Light should be turned on after power for logic and interface signal are valid. B2-82-O (3/3) DV28FBM-NB Product Specification 5 of 28 A4(2 X 297)

16 6. OPTICAL SPECIFICATIONS PRODUCT GROUP REV ISSUE DATE TFT LCD O The test of optical specifications shall be measured in a dark room (ambient luminance lux and temperature=25 2 ) with the equipment of Luminance meter system (Goniometer system and PR73) and test unit shall be located at an approximate distance 5cm from the LCD surface at a viewing angle of θ and Φ equal to. We refer to θ Ø= (=θ 3 ) as the 3 o clock direction (the right ), θ Ø=9 (= θ 2 ) as the 2 o clock direction ( upward ), θ Ø=8 (= θ 9 ) as the 9 o clock direction ( left ) and θ Ø=27 (= θ 6 ) as the 6 o clock direction ( bottom ). While scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 3 minutes warm-up period. VDD shall be 2.V +/-% at 25 C. Optimum viewing angle direction is 6 clock. Viewing Angle < Table. Optical Table > [VDD = 2.V, Frame rate = 2Hz, Ta =25± 2 ] Parameter Symbol Condition Min Typ Max Unit Remark 2D Contrast ratio Horizontal Vertical Θ 3 89 Deg. Θ 9 89 Deg. CR > Θ 2 89 Deg. Θ 6 89 Deg. CR W y.29 Θ = R x (Center) TBD. R y Normal TBD. Viewing G x TBD. Angle TBD. Note 2: Note 2 Luminance of White Y w 8 cd/m 2 Note3 White luminance uniformity ΔY 75 % Note4 Reproduction of color Color Gamut 68 % White Red Green Blue W x.28 G y B x B y TBD. TBD. Note5 Response Time G to G T g 6 8 ms Note 6 Gamma Scale Cell Transmittance 6.7 % B2-82-O (3/3) DV28FBM-NB Product Specification 6 of 28 A4(2 X 297)

TFT LCD O 24.6.26 Note :. Viewing angle is the angle at which the contrast ratio is greater than.

17 TFT LCD O Note :. Viewing angle is the angle at which the contrast ratio is greater than. The viewing are determined for the horizontal or 3, 9 o clock direction and the vertical or 6, 2 o clock direction with respect to the optical axis which is normal to the LCD surface. 2. Contrast measurements shall be made at viewing angle of = and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See Figure shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. CR = Luminance when displaying a white raster Luminance when displaying a black raster 3. Center Luminance of white is defined as the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in Figure 2 for a total of the measurements per display. 4. The White luminance uniformity on LCD surface is then expressed as : ΔY = ( Minimum Luminance of 5 points / Maximum Luminance of 5 points ) * (See Figure 2 shown in Appendix). 5. The color chromaticity coordinates specified in Table. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. 6. Response time Tg is the average time required for display transition by switching the input signal as below table and is based on Frame rate fv =6Hz to optimize. Each time in below table is defined as Figure 3 and shall be measured by switching the B2-82-O (3/3) DV28FBM-NB Product Specification 7 of 28 A4(2 X 297)

18 7. MECHANICAL CHARACTERISTICS 7. Dimensional Requirements PRODUCT GROUP REV ISSUE DATE TFT LCD O Figure 4(located in Appendix) shows mechanical outlines for the model DVB28FBM-NB Other parameters are shown in Table. < Table 2. Dimensional Parameters > Parameter Specification Unit Dimensional outline 73.2(H) 65.4(V).8(D) mm Weight TBD Kg Active area 697.7(H) 3.8(V) mm Pixel pitch um Number of pixels 366(H) 256(V) ( pixel = R + G + B dots) pixels Back-light Edge Type LED Backlight 7.2 Mounting See Figure 5 (Shown in Appendix) 7.3 Anti-Reflection and Polarizer Hardness The surface of the LCD has an Anti-Reflection coating to minimize reflection and a coating to reduce scratching. B2-82-O (3/3) DV28FBM-NB Product Specification 8 of 28 A4(2 X 297)

19 8. Reliability Test Condition PRODUCT GROUP REV ISSUE DATE TFT LCD O < Table 3. Reliability Test Condition > Item Test Condition High-Temp/STG Low-Temp/STG High-Temp/HMD High-Temp/OP Low-Temp/OP Ta = 6, 24 hrs Ta = -2, 24 hrs Ta = 5, 8%RH, 24hrs Ta = 5, 24hrs Ta =, 24hrs TST Ta = -2 6 (.5 hr), cycle Vibration Frequency:-3 Hz Gravity / AMP :. G rms Period : X, Y, Z 3 min Shock Gravity : 5G Pulse width : msec, Half Sine ± X, ± Y, ± Z Once for each direction ESD Air:± 5kV,5pF/33Ω,Point,time/Point Contact:± 8kV,5pF/33Ω,Point, time/point This test condition is based on BOE module. B2-82-O (3/3) DV28FBM-NB Product Specification 9 of 28 A4(2 X 297)

20 9. PRODCUT SERIAL NUMBER PRODUCT GROUP REV ISSUE DATE TFT LCD O DV28FBM-NB X X X X X X X X X X X X X X X X X. Control Number 2. Rank / Grade 3. Line Classification 4. Year (2 :, 22 : 2, ) 5. Month (,2,3,, 9, X, Y, Z) 6. Internal Use 7. Serial Number B2-82-O (3/3) DV28FBM-NB Product Specification 2 of 28 A4(2 X 297)

21 . PACKING INFORMATION PRODUCT GROUP REV ISSUE DATE TFT LCD O BOE provides the standard shipping container for customers, unless customer specifies their packing information. The standard packing method and Barcode information are shown in below.. Packing Order B2-82-O (3/3) DV28FBM-NB Product Specification 2 of 28 A4(2 X 297)

TFT LCD O 24.6.26.2 Packing Note Box Dimension : 89mm(L) 53mm (W) 297.4mm (H) Package Quantity in one Box : 7pcs.

22 TFT LCD O Packing Note Box Dimension : 89mm(L) 53mm (W) 297.4mm (H) Package Quantity in one Box : 7pcs.3 Box Label Label Size : mm (L) 55 mm (W) Contents Model : DV28FBM-NB Q`ty : 7pcs Module in one box. Serial No. : Box Serial No. See next page for detail description. Date : Packing Date DV28FBM-NB 7 2X.X.XX XXXX Type Grade Year Month ITEM-CODE Serial_no Internal CODE RoHS Mark B2-82-O (3/3) DV28FBM-NB Product Specification 22 of 28 A4(2 X 297)

23 . HANDLING & CAUTIONS PRODUCT GROUP REV ISSUE DATE TFT LCD O () Cautions when taking out the module Pick the pouch only, when taking out module from a shipping package. (2) Cautions for handling the module As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. As the LCD panel and back - light element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care. (3) Cautions for the operation When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the LCD panel would be damaged. Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged. (4) Cautions for the atmosphere Dew drop atmosphere should be avoided. Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended. (5) Cautions for the module characteristics Do not apply fixed pattern data signal to the LCD module at product aging. Applying fixed pattern for a long time may cause image sticking. (6) Other cautions Do not disassemble and/or re-assemble LCD module. Do not re-adjust variable resistor or switch etc. When returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages. B2-82-O (3/3) DV28FBM-NB Product Specification 23 of 28 A4(2 X 297)

24 TFT LCD O APPENDIX < Figure. Measurement Set Up > PR73 (L = 5cm ) < Figure 2. White Luminance and Uniformity Measurement Locations > B2-82-O (3/3) DV28FBM-NB Product Specification 24 of 28 A4(2 X 297)

25 TFT LCD O < Figure 2. Response Time Testing > B2-82-O (3/3) DV28FBM-NB Product Specification 25 of 28 A4(2 X 297)

26 TFT LCD O < Figure 3. TFT-LCD Open Cell (Front View) > B2-82-O (3/3) DV28FBM-NB Product Specification 26 of 28 A4(2 X 297)

27 TFT LCD O < Figure 4. TFT-LCD Module Outline Dimensions (Front View) > B2-82-O (3/3) DV28FBM-NB Product Specification 27 of 28 A4(2 X 297)

28 TFT LCD O < Figure 5. TFT-LCD Module Outline Dimensions (Rear View) > B2-82-O (3/3) DV28FBM-NB Product Specification 28 of 28 A4(2 X 297)

TITLE : HT260WXC-200 Product Specification Rev. P1

TITLE : HT260WXC-200 Product Specification Rev. P1 PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF BOE HF AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HF AND MUST BE RETURNED TO BOE HF UPON ITS REQUEST. TFT-LCD. OF