Access control C485FX. Technical manual

Transcription

1 Access control C485FX Technical manual

2

3 Technical manual C485FX V1.3 p 3/16 Contents Contents... 3 Acknowledgement... 4 Information and recommendations... 5 Technical specifications... 6 Use of C485FX interface via US... 7 Declare C485FX in US mode in SENATORFX.NET... 8 Use of C485FX interface with a MOD-TCPIP module Declare C485FX in IP mode in SENATORFX.NET Use of C485FX interface via serial port Declare C485FX in Serial mode in SENATORFX.NET Check list Notes... 15

4 Technical manual C485FX V1.3 p 4/16 Acknowledgement Dear Client, You have just purchased C485FX communication interface created by EDEN INNOVATIS. The entire EDEN INNOVATIS team would like to thank you for your interest as well as your confidence in our security solution. We hope that you will be completely satisfied with the level of security it provides for your company s premises. Should you have any comments, please contact us via our web site at

5 Technical manual C485FX V1.3 p 5/16 Information and recommendations o In accordance with the European directive UTE C describing the directives 89/336 EEC and 92/31 EEC, C485FX complies with the following standards: NF EN for electromagnetic emissions and NF EN for electromagnetic susceptibility. o Wiring recommendations: the cables used to connect the drives, network and other devices must be installed according to the instructions describing Level 2 (protected environment) of the NF EN standard. o This product must be installed by a qualified contractor. Incorrect installation and use are liable to cause an electric shock or fire hazard. efore conducting the installation, read the technical manual and follow the product assembly recommendations. o After switching off the power supply, all the internal capacitors will discharge at a healthy level after 60 seconds under normal conditions. However, in the event of a fault, the charging may be maintained for a much longer time and suitable precautions must be taken before handling the product.

6 Technical manual C485FX V1.3 p 6/16 Technical specifications Maximum consumption... 12V (external power supply) Power supply voltage VDC Weight g lbs Housing dimensions x 80 x 32 mm (116 x 80 x 35 mm with IP module) x 2.8 x 1.38 in (4.61 x 2.8 x 1.12 in with IP module) Operating temperature C to +50 C F to +122 F Compatible US types... US 1.1 / US 2.0

7 Technical manual C485FX V1.3 p 7/16 Use of C485FX interface via US US (cable supplied) Note: If you use several US interfaces on the same PC, remember to configure the addressing switches. A RS485 bus Screen Power Switch Note: The power switch should therefore be positioned on Alim. US' (US power). Data sheet: A SYT recommended 1200m (2730 ft) Max Ø 0.6 mm (1/30 in) 2 pairs recommended A e sure to use the same pair for A and Characteristic: Sensitive connection Screen: Mandatory Maximum number of US interfaces per PC: 16 To reach 1200 m (2730 ft), you need to install a 120Ω resistor at each end of the network between points A and. Warning: The control units are connected in parallel. It is possible to go from one control to another or to several control units: in all cases, the total length must not exceed the recommended distance.

8 Technical manual C485FX V1.3 p 8/16 Declare C485FX in US mode in SENATORFX.NET Select Technique in the right, then click on Site configuration. Right click on Site Configuration, and select Create a network in the context menu for a new installation. For an existing network, right click on the network and select Modify in the context menu. In the window displayed, assign a name to the network, in the Name field. Select US in the Type field. Enter the address of your interface (as shown in next page). Validate by pressing OK.

9 Technical manual C485FX V1.3 p 9/16 1 st C485FX : Address 0 2 nd C485FX : Address 1 3 rd C485FX : Address 2 4 th C485FX : Address 3 5 th C485FX : Address 4 6 th C485FX : Address 5 7 th C485FX : Address 6 8 th C485FX : Address 7 9 th C485FX : Address 8 10 th C485FX : Address 9 11 th C485FX : Address th C485FX : Address th C485FX : Address th C485FX : Address th C485FX : Address th C485FX : Address 15

10 Technical manual C485FX V1.3 p 10/16 Use of C485FX interface with a MOD-TCPIP module Insert your module as follows MOD-TCPIP A RS485 bus Screen Power switch ( External PS ) 12V/700 ma Note: To use the C485FX interface with a MOD-TCPIP module, you must use an external 12 V / 700 ma power supply. The power switch should therefore be positioned on Alim. Externe (External power supply). (?) Data sheet: A SYT recommended 1200m (2730 ft) Max Ø 0.6 mm (1/30 in) 2 pairs recommended e sure to use the same pair for A and e sure to separate the supply from RS485 bus A Characteristic: Sensitive connection Screen: Mandatory To achieve 1200 m, you need to install a 120Ω resistor at each end of the network between points A and. Warning: The control units are connected in parallel. It is possible to go from one control to another or to several control units: in all cases, the total length must not exceed the recommended distance.

11 Technical manual C485FX V1.3 p 11/16 Declare C485FX in IP mode in SENATORFX.NET Select Technique in the right, then click on Site configuration. Right click on Site Configuration, and select Create a network in the context menu for a new installation. For an existing network, right click on the network and select Modify in the context menu. In the window displayed, assign a name to the network, in the Name field. Select Socket IP in the Type field. Enter the MOD-TCP/IP address in the Address field, or click on Search button to find it. You can use drag and drop from search window to Address field in network window to auto-write the address. Validate by pressing OK. The Search button will run Config IP software. It will automatically start a detection of all units available. At the end of the scan, select the line of your MOD-TCPIP and drag and drop it into the Address area of the previous window.

12 Technical manual C485FX V1.3 p 12/16 Use of C485FX interface via serial port Serial cable (not supplied) A RS485 bus Screen Power switch 12V/700 ma Note: To use the C485FX interface on a serial port, you must use a 12V / 700 ma external power source. The power switch should therefore be positioned on Alim. Externe (External power supply). (?) Data sheet: A SYT recommended 1200m (2730 ft) Max Ø 0.6 mm (1/30 in) 2 pairs recommended A Characteristic: Sensitive connection Screen: Mandatory To achieve 1200 m, you need to install a 120Ω resistor at each end of the network between points A and. Warning: The control units are connected in parallel. It is possible to go from one control to another or to several control units: in all cases, the total length must not exceed the recommended distance.

13 Technical manual C485FX V1.3 p 13/16 Declare C485FX in Serial mode in SENATORFX.NET Select Technique in the right, then click on Site configuration. Right click on Site Configuration, and select Create a network in the context menu for a new installation. For an existing network, right click on the network and select Modify in the context menu. In the window displayed, assign a name to the network, in the Name field. Select Serial in the Type field. Enter the interface address in the Address field. Validate by pressing OK.

14 Technical manual C485FX V1.3 p 14/16 Check list C485FX Serial number : US cable : Connector block check :

15 Technical manual C485FX V1.3 p 15/16 Notes Support Technique : hotline@eden-innovations.com

16 Technical manual C485FX V1.3 p 16/16 Zone Commerciale et Artisanale 670, route de erre EGUILLES France