PRIMERGY BX922 S2. System configurator and order-information guide August PRIMERGY Server. Contents

Transcription

1 PRIMERGY BX922 S2 System configurator and order-information guide August 2012 Contents Instructions Configuration diagram Configurator # X BX922 S2 Dual Socket 10 # XI Processor 11 # XII Memory 12 # XIII Storage 13 # XIV irmc S2, Graphics 14 # XV Mezzanine Cards 15 # PRIMERGY Server

2 Instructions This document contains basic product and configuration information that will enable you to configure your system via System-Architect. Only the tool "System-Arcitect" will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system. Please pay attention to the naming conventions: BX900 S1 System unit 1nd generation BX922 S2 Dual Server Blade S2 You can configure your individual PRIMERGY server in order to adjust your specific requirements. The System configurator is divided into several chapters that are identical to the current price list and PC-/ System-Architect. Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through the configurator by following the lines from the top to the bottom. Section IV Memory, example There are 3 free memory banks available. The memory banks can be populated with 512MB, 1GB, 2GB and 4GB DDR Memory. The maximum total amount of memory is 12GB. It is possible to select memory upgrade options up to 3 times. ECC with memory scrubbing-function and hot-spare memorybank is standard on the PRIMERGY BX600 S2 Server Blades. X times S26361-XXX-XXX Memory XXX MB S26361-XXX-XXX Memory XXX MB max. X times per system max. X times per system In one chapter you can only select as many components (here 3x) as the arrow indicates. 3x Please note that there are information symbols which indicate necessary information. For further information see: (internet) (extranet) Prices and availability see price list and PC-/ System-Architect Subject to change and errors excepted Fujitsu Technology Solutions x86 PRIMERGY Server 2 of 15

3 Configuration diagram Dual Server Blade BX922 S2 Mezzanine slot 1 CPU1 Row 1 (3 DIMMS) FC Mezz. card SATA SSD 1 GbE Mezz. card Intel CPU IB Mezz. card Row 2 (3 DIMMS) or unpopulated SATA SSD Mezzanine slot 2 FC Mezz. card CPU2 Row 1 (3 DIMMS) 1 GbE Mezz. card IB Mezz. card Intel CPU or Disk drives Row 2 (3 DIMMS) unpopulated UFM Processor Memory Mezzanine slot UFM Key: Included in basic unit Option The population order for the CPU is: CPU1 first, then CPU2 The population order for the DIMMs: for each CPU, the DIMM row 1 (DIMMS 1A 1B 1C) (DIMMS 1D 1E 1F) first, then row 2 (DIMMs 2A, 2B, 2C) (DIMMs 2D, 2E, 2F) Fujitsu Technology Solutions x86 PRIMERGY Server 3 of 15

4 UDIMM 1.35V 1333Mhz UDIMM 1.5V 1333Mhz RDIMM 1333Mhz RDIMM 1.5V 1333Mhz System configurator and order-information guide Memory Configuration PRIMERGY BX922 S2 The first CPU offers 6 Slots for DDR3 Memory Modules organised in 2 Banks and 3 Channels. If you need more than 6 Slots you have to configure the 2nd CPU. The second CPU offers 6 Slots for DDR3 Memory Modules organised in 2 Banks and 3 Channels. Depending on the amount of memory configured you can decide between 3 basic modes of operation (see explanation below). There are 2 different kinds of DDR3 Memory Modules available: UDIMM and RDIMM. UDIMM and RDIMM offer different functionality. Mode Configuration UDIMM RDIMM Application chip kill support any n.a. yes detect multi-bit errors Independant Channel Mode 1, 2 or 3 Modules per Bank x x offers max. flexibility, upgradeability, capacity use UDIMM modules for lowest cost Mirrored Channel Mode 2 identical Modules / Bank **) x offers maximum security Performance Mode *) 3 identical Modules / Bank **) x offers maximum performance and capacity *) = Performance Mode and Spare mode use different BIOS settings. **) = technically possible but no Order Numbers available, use at your own risk x = order codes available Memory-Speed: Max. DDR3 memory speed depends on the memory configuration on one memory channel and the speed of the CPU One DIMM per channel = max. 1333MHz, two DIMMs per channel = max. 1333MHz for 1.5V / max for 1.35V memory, three DIMMs per channel = max. 800MHz (if applicable, depending on the system). system The memory channel with the lowest speed defines the speed of all CPU channels in the system DIMM Type DIMM Slots DIMMs populated Memory Speed Ranks per DIMM per Channel per Channel max (CPU dependent) LV / 1.35V 2 / , 1066, 1333 SR / DR 2 / , 1066 QR 2 / 3 2 / , 1066, Mix of SR + DR Mix of QR + SR / DR Mix of SR + DR 2 / / / / / , 1066, 1333 SR / DR 800, 1066 QR* 800, 1066 Mix of SR + DR 800, 1066, 1333 SR / DR Mix of QR* + SR / DR Mix of SR + DR ** 2 / , 1066, 1333 Mix of SR + DR LV / 2 / , 1066, 1333 SR / DR 2 / , 1066 Mix of SR + DR * no memory modules released for this configuration ** lost LV-mode, memory will switch to 1,5V Vcc automatically Fujitsu Technology Solutions x86 PRIMERGY Server 4 of 15

5 UDIMM 1333 MHz 1.5V UDIMM 1333 MHz LV / 1.35V RDIMM 1333 MHz 1.5V RDIMM 1333 MHz LV / 1.35V RDIMM 1066 MHz (QR) 1.5V System configurator and order-information guide Used CPU Max. Memory-Bus speed depending on DIMMs / channel if following memory speed is used for specific CPU`s Populated Dimms / Channel Dual-Core CPU with max. 800MHz DDR3 speed (4.8GT/s) Xeon E5503 2C/2.00GHz/2M/4,80GT/s (80W) Quad-Core CPU`s with max. 800MHz DDR3 speed (4.8GT/s) Xeon E5506 4C/2.13GHz/4M/4,8GT/s (80W) Xeon E5507 4C/2.26GHz/4M/4,8GT/s (80W) Turbo Quad-Core CPU`s with max. 1066MHz DDR3 speed (5.86GT/s) Xeon E5620 4C/2.40GHz/12M/5,86GT/s (80W) Xeon E5630 4C/2.53GHz/12M/5,86GT/s (80W) Xeon E5640 4C/2.66GHz/12M/5,86GT/s (80W) Turbo Six-Core CPU`s with max. 1333MHz DDR3 speed (6.4GT/s) Xeon X5650 6C/2.66GHz/12M/6,40GT/s (95W) Xeon X5660 6C/2.80GHz/12M/6,40GT/s (95W) Xeon X5670 6C/2.93GHz/12M/6,40GT/s (95W) Xeon X5680 6C/3.33GHz/12M/6,40GT/s (130W) Frequency Optimized Turbo Quad-Core CPU`s with max. 1333MHz DDR3 speed (6.4GT/s) Xeon X5667 4C/3.06GHz/12M/6,40GT/s (95W) Xeon X5677 4C/3.46GHz/12M/6,40GT/s (130W) Low Voltage Quad-Core CPU with max. 800MHz DDR3 speed (4.8GT/s) Xeon L5609 4C/1.60GHz/12M/4.80GT/s (40W) Low Voltage Turbo Quad-Core CPU with max. 1066MHz DDR3 speed (5.86GT/s) Xeon L5630 4C/2.13GHz/12M/5,86GT/s (40W) Xeon L5640 6C/2.40GHz/12M/5.86GT/s (60W) SR - Single Rank - 1Rx4 DR - Dual Rank - 2Rx4 QR - Quad Rank - 4Rx4 1DPC = 1 DIMM per Channel 2DPC = 2 DIMM per Channel 3DPC = 3 DIMM per Channel not supported special release Configuration hints: - The memory sockets on the systemboard offer a color coding: Bank I black sockets Bank II blue sockets - A so called Bank consits of 1 memory module on every Channel available on one CPU (examples see below) Bank I on CPU 1 up to 3 memory modules connected to Channel A, B and C on the first CPU Bank II on CPU 1 up to 3 memory modules connected to Channel A, B and C on the first CPU Bank I on CPU 2 up to 3 memory modules connected to Channel D, E and F on the second CPU - See below (next page) for a detailed descriptions of the memory configuration supported. Fujitsu Technology Solutions x86 PRIMERGY Server 5 of 15

6 Channel A Channel B Channel C Channel D Channel E Channel F Channel A Channel B Channel C Channel D Channel E Channel F Channel A Channel B Channel C Channel D Channel E Channel F 1. Independent Channel Mode System configurator and order-information guide required required if 2nd CPU is configured Bank I Data Data Data Data Data Data optional, same type in Bank per CPU (black sockets) Bank II Data Data Data Data Data Data optional, any type (blue sockets) 1st XEON CPU (Dual-or Quad Core) not used Independent Channel Mode allows all channels to be populated in any order Can run with differently rated DIMMs and use the settings of the slowest DIMM installed in the system Independent Channel Mode is supported using UDIMM or RDIMM memory modules 2. Mirrored Channel Mode 2nd XEON CPU (Dual-or Quad Core) required required if 2nd CPU is configured Bank I Data Mirror Data Mirror optional, same type in Bank per CPU (black sockets) Bank II Data Mirror Data Mirror optional, any type (blue sockets) 1st XEON CPU (Dual-or Quad Core) not used Mirrored Channel Mode requires identical modules on channel A and B (1st CPU) or channel D and E (2nd CPU) 50% of the capacity is used for the mirror => the available memory for applications is only half of the installed memory channel C (1st CPU) or channel F (2nd CPU) are not usable in Mirrored Channel Mode Mirrored Channel Mode is supported using RDIMM memory modules 3. Performance Channel Mode 2nd XEON CPU (Dual-or Quad Core) required required if 2nd CPU is configured Bank I Data Data Data Data Data Data optional, same type in Bank per CPU (black sockets) Bank II Data Data Data Data Data Data optional, any type (blue sockets) 1st XEON CPU (Dual-or Quad Core) 2nd XEON CPU (Dual-or Quad Core) not used Performance Channel Mode requires identical modules on all channels of each Bank per CPU Performance Channel Mode is supported using RDIMM memory modules Fujitsu Technology Solutions x86 PRIMERGY Server 6 of 15

7 D Section X Dual Socket Server Blade BX922 S2 Server Blade with: - Dual INTEL Nehalem/Westmere Processor Support as Dual-Core / Quad-Core / Six-Core - The base units with INTEL Processor - 12 DIMM sockets, organized in 2 row (6 DIMM) for each CPU - 2x Intel Kawela dual channel Gbit Ethernet LAN controller on-board (=4x 10/100/1000 Mbit/s) - 2 bays for 2.5" SATA SSD disks (non hot-plug) optional - irmc2 on-board - Special connector for Y-cable (4x USB, 1 x serial 1x VGA). The BX922 S2 Server Blade can be installed max. 18x in the BX900 S1 System Unit S26361-K1247-V200 PY BX922 S2 Dual Server Blade up to 2x 2.5" SSD drives. Dual Server Blade Base Unit without CPU and without memory modules! PY BX922 S2 Dual Server Blade For CPU and Memory configuration see below Max. 18x per BX900 System Unit. S26361-F4478-L1 PY BX900 Y-Cable frontside for KVM connection to Server Blade 4x USB, 1x VGA, 1x seriell S26361-F3552-E1 TPM Module Trusted Platform Module on motherboard PY TPM Module Be aware of import restrictions! Max. 1x per Server Blade. If installation is done locally, make sure you have USB stick available for driver installation. Following USB Components are available 1) USB DVD SM / Blu-Ray as soon as available External SuperMulti Drive External Blu-Ray Drive S26341-F103-L126 S26341-F103-L127 2) USB Keyboard: KBPC PX ECO Green IT, professional keyboard S26381-K341-E1xx / L1xx 3) USB Mouse: S26381-K430-L100 Laser Moue USB/PS2 Combo 4) USB Sticks: MyUSBS A910 8GB, MLC Flash MyUSBS A910 16GB, MLC Flash S26391-F6048-L208 S26391-F6048-L216 S26361-F2749-E1 S26361-F2749-E2 Service for Server Blade installation in the System Unit. Server Blade individually packed / delivered. Hereby the BX900 S1 will be delivered completely The Server Blade is not built in a BX900 S1, configured and tested with Server Blades integrated. it is separately tested and delivered. This order number must be in the same order as the System Unit itself. Contains ServerStart CD min. 1x per System Unit; max. 18x per System Unit; max. 1x per Server Blade max. 1x per Server Blade E Fujitsu Technology Solutions x86 PRIMERGY Server 7 of 15

8 E System configurator and order-information guide Section XI Processor There are 2 processor sockets available. The first socket is always equipped with the first CPU which can be selected via configurator It is also possible to upgrade a dual-processor system later on with a second CPU Two processors with different clock frequencies are not possible A multi-processor operating system is required for a dual-processor system. Note: Max. DDR3 Bus Speed depends on: - max. DDR3 Bus Speed from the CPU and - max. DDR3 Memory Speed and Max. two CPU`s can be selected per basic unit One of following CPU s must to be selected as first CPU for an orderable basic unit Optional second CPU has to be the same type like the first CPU Dual-Core CPU with max. DDR3 Bus Speed 800MHz - 1x 64-bit Intel Xeon DP (4MB shared TLC = Second Level Cache ) occupies socket for one CPU Xeon E5503 2C/2.00GHz/2M/4,80GT/s (80W) S26361-F4423-E200 Quad-Core CPU`s with max. DDR3 Bus Speed 800MHz - 1x 64-bit Intel Xeon DP (4MB shared TLC = Second Level Cache ) occupies socket for one CPU Xeon E5506 4C/2.13GHz/4M/4,8GT/s (80W) S26361-F3972-E213 Xeon E5507 4C/2.26GHz/4M/4,8GT/s (80W) S26361-F4423-E226 Quad-Core CPU`s with max. DDR3 Bus Speed 1066MHz - 1x 64-bit Intel Xeon DP (4/8MB shared TLC = Second Level Cache ) occupies socket for one CPU Xeon E5603 4C/1.60GHz/4M/4,80GT/s (80W) S26361-F4507-E160 Xeon E5606 4C/2.13GHz/8M/4,80GT/s (80W) S26361-F4507-E213 Xeon E5607 4C/2.26GHz/8M/4,80GT/s (80W) S26361-F4507-E226 on special release Turbo Quad-Core CPU`s with max. DDR3 Bus Speed 1066MHz - 1x 64-bit Intel Xeon DP (12MB shared TLC = Second Level Cache ) 1-2x occupies socket for one CPU Xeon E5620 4C/2.40GHz/12M/5,86GT/s (80W) S26361-F4425-E240 Xeon E5630 4C/2.53GHz/12M/5,86GT/s (80W) S26361-F4425-E253 Xeon E5640 4C/2.66GHz/12M/5,86GT/s (80W) S26361-F4425-E266 Turbo Quad-/Six-Core CPU`s with max. DDR3 Bus Speed 1333MHz - 1x 64-bit Intel Xeon DP (12MB shared TLC = Second Level Cache ) occupies socket for one CPU Xeon E5645 6C/2.40GHz/12M/5,86GT/s (80W) S26361-F4508-E240 Xeon E5649 6C/2.53GHz/12M/5,86GT/s (80W) S26361-F4508-E253 Xeon X5650 6C/2.66GHz/12M/6,40GT/s (95W) S26361-F4427-E266 Xeon X5660 6C/2.80GHz/12M/6,40GT/s (95W) S26361-F4427-E280 Xeon X5670 6C/2.93GHz/12M/6,40GT/s (95W) S26361-F4427-E293 Xeon X5675 6C/3.06GHz/12M/6,40GT/s (95W) S26361-F4509-E306 Xeon X5667 4C/3.06GHz/12M/6,40GT/s (95W) S26361-F4433-E306 on special release Low Voltage Quad-Core CPU with max. 800MHz DDR3 speed ( 4.8GT/s) - 1x 64-bit Intel Xeon DP (12MB shared TLC = Second Level Cache ) with passive heat sink, occupies socket for one CPU Xeon L5609 4C/1.86GHz/12M/4.80GT/s (40W) S26361-F4429-E186 Low Voltage Turbo Quad-Core CPU`s with max. DDR3 Bus Speed 1066MHz - 1x 64-bit Intel Xeon DP (12MB shared TLC = Second Level Cache ) occupies socket for one CPU Xeon L5630 4C/2.13GHz/12M/5,86GT/s (40W) S26361-F4429-E213 Xeon L5640 6C/2.26GHz/12M/5.86GT/s (60W) S26361-F4431-E226 For 130W CPUs a different CPU Heatsinks are required for CPU1 and CPU2 For the first CPU use one of the following CPUs Turbo Quad-/Six Core CPU`s with max. DDR3 Bus Speed 1333MHz 130W - 1x 64-bit Intel Xeon DP (12MB shared TLC = Second Level Cache ) occupies socket for one CPU Xeon X5647 4C/2.93GHz/12M/5,86GT/s (130W) S26361-F4512-E293 Xeon X5677 4C/3.46GHz/12M/6,40GT/s (130W) S26361-F4441-E346 on special release Xeon X5687 4C/3.60GHz/12M/6,40GT/s (130W) Xeon X5680 6C/3.33GHz/12M/6,40GT/s (130W) Xeon X5690 6C/3.46GHz/12M/6,40GT/s (130W) S26361-F4512-E360 S26361-F4440-E333 S26361-F4512-E346 For 130W CPUs different CPU Heatsinks are required for CPU1 and CPU2 For the second CPU use one of the following order numbers Turbo Quad-/Six Core CPU`s with max. DDR3 Bus Speed 1333MHz 130W - 1x 64-bit Intel Xeon DP (12MB shared TLC = Second Level Cache ) occupies socket for one CPU Xeon X5647 4C/2.93GHz/12M/5,86GT/s (130W) S26361-F4513-E293 Xeon X5677 4C/3.46GHz/12M/6,40GT/s (130W) S26361-F4443-E346 on special release Xeon X5687 4C/3.60GHz/12M/6,40GT/s (130W) Xeon X5680 6C/3.33GHz/12M/6,40GT/s (130W) Xeon X5690 6C/3.46GHz/12M/6,40GT/s (130W) S26361-F4513-E360 S26361-F4442-E333 S26361-F4513-E346 F Fujitsu Technology Solutions x86 PRIMERGY Server 8 of 15

9 F Section XII Memory - There are 6 memory slots for max. 96GB registered (reg) DDR3 RAM per CPU available with 16GB RDIMMs or max. 12GB unbuffered (ub) DDR3 RAM per CPU available with 2GB UDIMMs => max. 192GB registered or 24GB unbuffered RAM for two CPU`s possible ( For explanation of following terms refer to section "Memory Configurations" - The memory area is divided into 3 channels per CPU with 2 slots per channel - Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2 Registered and unbuffered memory modules can be selected No mix of registered and unbuffered modules allowed. DDR and 1333MHz modules can be mixed, but run always with the slower speed. With two DIMMs per channel, 1.5V DIMMs operate with 1333Mhz, 1.35V with 1066MHz as max., dep. on CPU If 1.5V DIMMs and 1.35V (Low Voltage) DIMMs are mixed, DIMMs at appropriate CPU Channel will run at 1.5V SDDC (Chipkill) is supported only for registered memory modules. 1.) In the "Independent Channel Mode" is following configuration possible - Each slot can optionally be equipped either with registered x4 organized DDR3 modules: 2GB Single Rank (SR), 4GB and 8GB Dual Rank (DR), 16GB Quad Rank (QR) or with unbuffered x8 organized DDR3 modules: 1GB Single Rank (SR) and 2GB Dual Rank (DR) 2.) In the "Spare Channel Mode" is following configuration possible - Each memory bank can optionally be equipped with 3x2GB single rank, 3x4GB and 3x8GB DR or 3x 16GB QR DDR3 modules. Each slot of one bank has to be equipped with identical modules for spare channel mode In channel A and B of CPU 1 or channel D and E of CPU 2 are always the active memory modules, in channel C of CPU 1 and channel F of CPU 2 is always the spare module No special order codes with UDIMMs are offered for this mode 3.) In the "Mirrored Channel Mode" is following configuration possible - Each memory bank can optionally be equipped with 2x2GB single rank, 2x4GB and 2x8GB DR or 2x16GB QR DDR3 modules. In each memory bank channel A and B of CPU 1 or channel D and E of CPU 2 have to be equipped with identical modules for mirrored channel mode. Channel C of CPU 1 and channel F of CPU 2 is not equipped In channel B is always the mirrored memory of channel A of CPU 1 In channel E is always the mirrored memory of channel D of CPU 2 No special order codes with UDIMMs are offered for this mode - For each CPU minimum 1 memory module has to be configured in Independent Channel Mode ( => Additional memory extensions can still be configured up to five times per CPU ) or one bank has to be equipped with two modules (channel A+B for CPU 1 or D+E for CPU 2) in Mirrored Channel Mode ( => Additional memory extensions can still be configured up to one time per CPU ) or one bank has to be equipped with three modules (channel A+B+C for CPU 1 or D+E+F for CPU 2) in Spare Channel Mode or Performance Mode ( => Additional memory extensions can still be configured up to one time per CPU ) F1 Fujitsu Technology Solutions x86 PRIMERGY Server 9 of 15

10 F1 For a description of memory configurations refer to section "Memory Configurations" Minimum one memory module or memory order code per CPU = first memory Registered (reg) RDIMMs (1.5V) Note 1.) For "Independent Channel Mode" usage! Max. DDR3 memory speed depends on the memory configuration - One DDR3 RDIMM ECC memory module of one CPU memory channel and on the speed of the CPU itself. 2GB (1333MHz/SR) S26361-F4412-E513 The memory channel with the lowest speed defines the speed 4GB (1333MHz/DR) S26361-F4412-E514 of all CPU channels in the system, also for the channels of the 8GB (1333MHz/DR) S26361-F4412-E515 second CPU if configured. 16GB (1066MHz/QR) S26361-F4412-E516 One DIMM per channel = max. 1333MHz for 1.5V V memory Choose up to 6 order codes per CPU two DIMMs per channel = max. 1333MHz for 1.5V memory only 6x for each CPU Registered (reg) LV RDIMMs (1.35V) Note 2.) as soon as released with max. For "Independent Channel Mode" usage! LV Memory (1.35V) is only supported by 2 modules - One DDR3 LV RDIMM ECC memory module CPU Type *56xx per channel Note 3.) 4GB (1333MHz/DR) S26361-F4415-E514 Max. DDR3 memory speed 1333MHz is only 8GB (1333MHz/DR) S26361-F4415-E515 possible with CPU`s X56xx, providing 6.4GT/s QPI Note 4) Choose up to 6 order codes above per CPU Mix of Standard Voltage (1.5V) and Low Voltage (1.35V) Memory modules is supported but not recommended In mixed mode, all Memory modules will run at Standard Voltage (1.5V) Unbuffered (ub) UDIMMs cannot be mixed with registered (reg ) RDIMMs Memory speed in all configurations with UDIMMs is max. 1333MHz depending on the used CPU speed Unbuffered (ub) UDIMMs (1.5V) Unbuffered (ub) LV UDIMMs (1.35V) as soon as released For "Independent Channel Mode" usage! For "Independent Channel Mode" usage! 6x for each CPU - One DDR PC UB ECC mem. - One DDR3 LV 1333 PC UB ECC mem. with max. 2 modules 2GB (DR) S26361-F4413-E513 2GB (DR) S26361-F4416-E513 per channel No Chipkill No Chipkill Choose up to 6 order codes above per CPU Choose up to 6 order codes above per CPU F2 F3 Fujitsu Technology Solutions x86 PRIMERGY Server 10 of 15

11 F2 F3 S26361-F3284-E1 (only available with 56xx CPUs) Spare Channel Mode Installation With this order code a BIOS setup for spare mode is factory preinstalled The three identical memory modules of following order codes are always equipped in one memory bank to use the Spare Channel Mode In this mode only two modules are active the third module is the spare module S26361-F3284-E2 Performance Mode Installation With this order code BIOS setup is default for highest performance The three identical memory modules of following order codes are always equipped in one memory bank to run with highest performance In this mode all three modules are active and full capacity can be used Registered (reg) RDIMMs (1.5V) SP = for "Spare Channel and Performance Mode" usage! See Note 1.) - 4.) - Three DDR3 RDIMM ECC memory modules SP 6GB (3x 2GB 1333 MHz SR) S26361-F4412-E533 = 4GB usable memory for Spare Channel Mode = 6GB usable memory for Performance Mode SP 12GB (3x 4GB 1333 MHz DR) S26361-F4412-E534 = 8GB usable memory for Spare Channel Mode = 12GB usable memory for Performance Mode SP 24GB (3x 8GB 1333MHz DR) S26361-F4412-E535 = 16GB usable memory for Spare Channel Mode = 24GB usable memory for Performance Mode SP 48GB (3x 16GB 1066MHz QR) S26361-F4412-E536 = 32GB usable memory for Spare Channel Mode = 48GB usable memory for Performance Mode 2x for each CPU with max. 2 modules per channel Choose up to 2 order codes above per CPU. Registered (reg) LV RDIMMs (1.35V) SP = for "Spare Channel and Performance Mode" usage! See Note 1.) - 4.) - Three DDR3 LV RDIMM ECC memory modules SP 12GB (3x 4GB 1333 MHz DR) S26361-F4415-E534 as soon as released = 8GB usable memory for Spare Channel Mode = 12GB usable memory for Performance Mode SP 24GB (3x 8GB 1333MHz DR) S26361-F4415-E535 as soon as released = 16GB usable memory for Spare Channel Mode = 24GB usable memory for Performance Mode Choose up to 2 order codes above per CPU. G1 G2 Fujitsu Technology Solutions x86 PRIMERGY Server 11 of 15

12 G1 G2 S26361-F3284-E3 Mirrored Channel Mode Installation With this order code a BIOS setup for Mirrored Channel Mode is factory preinstalled The two identical memory modules of following order codes are always equipped in one memory bank to use the Mirrored Channel Mode In this mode only one module contains active data, the second modul contains the mirrored data Registered (reg) RDIMMs (1.5V) MM = for "Mirrored Channel Mode" usage! See Note 1.) - 4.) - Two DDR3 RDIMMs ECC memory modules MM 4GB (2x 2GB 1333MHz SR) S26361-F4412-E523 = 2GB usable for Mirrored Channel Mode MM 8GB (2x 4GB 1333MHz DR) S26361-F4412-E524 = 4GB usable for Mirrored Channel Mode MM 16GB (2x 8GB 1333MHz DR) S26361-F4412-E525 = 8GB usable for Mirrored Channel Mode MM 32GB (2x 16GB 1066MHz QR) S26361-F4412-E526 = 16GB usable for Mirrored Channel Mode Choose up to 2 order codes above per CPU. 2x for each CPU with max. 2 modules Registered (reg) LV RDIMMs (1.35V) per channel MM = for "Mirrored Channel Mode" usage! See Note 1.) - 4.) - Two DDR3 LV RDIMM ECC memory modules MM 8GB (2x 4GB 1333MHz DR) S26361-F4415-E524 as soon as released = 4GB usable for Mirrored Channel Mode MM 16GB (2x 8GB 1333MHz DR) S26361-F4415-E525 as soon as released = 8GB usable for Mirrored Channel Mode Choose up to 2 order codes above per CPU. H Fujitsu Technology Solutions x86 PRIMERGY Server 12 of 15

13 H Section XIII irmc S2, Graphics System configurator and order-information guide Graphic Controller is part of the onboard Management Controller irmc S2. Other graphics are not possible. The irmc S2 advanced pack is included in the system delivery. A corresponding license order is not necessary. Section XIV Storage Both hard disks are plugged in directly connected to the onboard controller. One UFM can be configured in addition to the Hard Disks Remark: UFM is part of the VMWare Embedded solution (S26361-F2341-E431) Remark: Currently VMWare RAID configuration are not supported 1x S26361-F4008-E1 Disk Drive mounting Kit supports up to 2 SSDs max. 1x per base unit SSD SATA 6Gb/s 2.5" with hot plug/hot replace tray 64GB SLC S26361-F4008-E64 1-2x 100GB MLC, Mainstream Perfomance S26361-F5123-E GB MLC, Mainstream Perfomance S26361-F5123-E GB MLC, Mainstream Perfomance S26361-F5123-E400 S26361-F3599-E160 S26361-F3599-E320 S26361-F3599-E x HD 160GB 5.4krpm 2.5" HD 320GB 5.4krpm 2.5" HD 500GB 5.4krpm 2.5" 5400rpm,<10,5ms, 8MB Cache 5400rpm,<10,5ms, 8MB Cache 5400rpm,<10,5ms, 8MB Cache ECO SATA ECO SATA ECO SATA non hot plug non hot plug non hot plug max. 2x per base unit max. 2x per base unit max. 2x per base unit S26361-F3625-E250 S26361-F3625-E500 S26361-F3625-E100 1 x HD 250GB 7.2krpm 2.5" HD 500GB 7.2krpm 2.5" HD 1000GB 7.2krpm 2.5" 7200rpm,<9,5ms, 32MB Cache 7200rpm,<9,5ms, 32MB Cache 7200rpm,<9,5ms, 32MB Cache BC SATA 3Gb/s BC SATA 3Gb/s BC SATA 3Gb/s non hot plug non hot plug non hot plug max. 1x per base unit max. 1x per base unit max. 1x per base unit I Both hard disks are plugged in directly connected to the onboard controller. One UFM can be configured in addition to the Hard Disks Remark: UFM is part of the VMWare Embedded solution (S26361-F2341-E431) Remark: Currently VMWare RAID configuration are not supported 1x S26361-F4008-E1 Disk Drive mounting Kit supports up to 2 SSDs max. 1x per base unit S26361-F4008-E32 S26361-F4008-E64 1-2x SSD 32GB SSD 64GB SATA 3Gb/s SATA 3Gb/s non hot plug non hot plug max. 2x per base unit max. 2x per base unit S26361-F3599-E160 S26361-F3599-E320 S26361-F3599-E x HD 160GB 5.4krpm 2.5" HD 320GB 5.4krpm 2.5" HD 500GB 5.4krpm 2.5" 5400rpm,<10,5ms, 8MB Cache 5400rpm,<10,5ms, 8MB Cache 5400rpm,<10,5ms, 8MB Cache ECO SATA ECO SATA ECO SATA non hot plug non hot plug non hot plug max. 2x per base unit max. 2x per base unit max. 2x per base unit S26361-F3625-E250 S26361-F3625-E500 S26361-F3625-E100 1 x HD 250GB 7.2krpm 2.5" HD 500GB 7.2krpm 2.5" HD 1000GB 7.2krpm 2.5" 7200rpm,<9,5ms, 32MB Cache 7200rpm,<9,5ms, 32MB Cache 7200rpm,<9,5ms, 32MB Cache BC SATA 3Gb/s BC SATA 3Gb/s BC SATA 3Gb/s non hot plug non hot plug non hot plug max. 1x per base unit max. 1x per base unit max. 1x per base unit I Fujitsu Technology Solutions x86 PRIMERGY Server 13 of 15

14 I System configurator and order-information guide Section XV Mezzanine cards for Dual Socket Server Blade The Dual Server Blade supports the following optional mezzanine cards. A Fibre Channel Switch / Pass-Thru blade, an Ethernet LAN Switch / Pass-Thru blade, SAS Switch respectively an InfiniBand switch is required in the system unit for this functionality. SAS Mezz Cards require an SAS switch for each SAS link SAS Mezz Cards has to be installed in Mezz Card slot 2 on Server Blade 1x S26361-F4481-E1 S26361-F4480-E1 PY SAS RAID Mezz Card 6Gb PY SAS HBA Mezz Card 6Gb MegaRAID HBA SAS 2.0 SAS 2.0 pluggable on the main board pluggable on the main board PCIe Gen2 interface PCIe Gen2 interface 4x SAS links to midplane 4x SAS links to midplane 2x SAS links to internal HDD's max. 1x per Server Blade max. 1x per Server Blade S26361-F4481-E10 RAID Mezz ibbu Upgrade ibbu08 Li-Ion max. 1x per Mezz Card Requires an Ethernet LAN Requires a Fibre Channel Requires an InfiniBand Switch, IBP or Pass-Thru Switch for each channel. Switch for each Mezz Card. Blade for each channel. S26361-F3331-E1 S26361-F3874-E1 S26361-F3992-E2 PY Eth Mezz Card 1Gb 4 Port PY FC Mezz Card 8Gb 2 Port PY IB CX2 Mezz Card 40Gb 2 Port 2x Intel Zoar controller Emulex LPe12002 compatible Interface to midplane: 4x 10/100/1000 Mbit/s. pluggable on the main board, 2x 10Gb/s(SDR), 2x 20Gb/s(DDR) 1-2x pluggable on the main board, MC-FC82E 2x 40Gb/s(QDR) Four channel 1Gbit/s Dual channel 8Gbit/s each Dual channel 40Gbit/s each PCIe x4 Interface PCIe x8 interface PCIe x8 interface max. 2x per Server Blade max. 2x per Server Blade max. 2x per Server Blade S26361-F3997-E1 PY Eth Mezz Card 10Gb 2 Port Intel 82599EB LAN Controller 2x 10Gbit/s. pluggable on the main board, Dual channel 10Gbit/s PCIe x8 Interface iscsi mode (planned) max. 2x per Server Blade S26361-F3592-E502 PY CNA Mezz Card 10Gb 2 Port Emulex OCe10102 compatible 2x 10Gbit/s DCB/FCoE pluggable on the main board, Dual channel 10Gbit/s PCIe x8 Interface max. 2x per Server Blade R S T U V R: see separate BX900 System Unit configurator, sheet "1 GB Ethernet" S: see separate BX900 System Unit configurator, sheet "10 GB Ethernet" T: see separate BX900 System Unit configurator, sheet "Fibre Channel" U: see separate BX900 System Unit configurator, sheet "InfiniBand" V: see separate BX900 System Unit configurator, sheet "SAS" Fujitsu Technology Solutions x86 PRIMERGY Server 14 of 15

15 Change Report Date Order number Changes S26361-F5225-E*00 New order for SATA SSD s Added ECO SATA HDD 500 GB S26361-F3625-Exxx Added BC Sata HDDs S26361-F3592-E502 Added new CNA Mezz Card S26361-F4507-E160 Westmere-EP Refresh CPUs added Updated USB Section Added ECO SATA HDD S26361-F4478-L1 Added Frontside Kabel All Westmere CPUs are available First Release Fujitsu Technology Solutions x86 PRIMERGY Server 15 of 15