DPC-D245 2-wire door station

Transcription

1 DPC-D245 2-wire door station. User manual

2 O N Introduction The door station is designed with high resolution color CCD camera, it provides wide angle of for 2-wire intercom system. The high white LED for night view makes the door station working efficiently at night. The front panel is made of plexiglass or stainless steel with rainy cover for better protection against water. One or two touch sensor call button can be selected. The large name label with white backlight is covered by a fully secured and flameproof glass plate. Parts and Function 35.6 Camera Lens Night View LED Speaker Nameplate Call Button Microphone Rainy Cover Note:the door station support two call buttons to control two users. Terminal Description Doorstation Code DIP T/R+ T/R Lock Control Jumper Connection line BUS(Blue&Green) S2+(Red) PL(White) S1+(Yellow) S1-(Black) -2

3 Lock Control Jumper: To select the lock type. Door Station Code DIP: Total 4 door stations can be supported. T/R+,T/R-: USB-RS485 communication terminal. Main Connect Port: To connect the bus line and the electronic locks. BUS(Blue&Green): Connect to the bus line, non-polarity. PL(White): External lock power input, connect to the power positive(power +). S1+(Yellow): The first lock power(+) output. S2+(Red): The second lock power(+) output. S-(Black): Lock power(-) output. Door Station Mounting Mounting with rainy cover Mounting without rainy cover

4 O N 1 2 The location of the unit should keep away from snow,rain,and intensity light. Installation Steps: Installation height for door station usually is 145~160cm. 1. Use screws to fix the back panel and rainy cover(if mounting with rainy cover) to the wall after connect the cable correctly. 2. Attach the front panel to the back panel, then use the screw to fix it. Adjusting Camera Angle Use a screwdriver to loosen the screw and then adjust the angle of the camera,then fix the screw. System Wiring and Connections Basic one-to-one Connection AC~ PC6 Bus PL S1+ S2+ S

5 Multi Door Stations Connection 4# Camera 3# Camera 2# Camera 1# Camera ID=11 ID=01 ID=10 ID= s Bus PL S1+ S2+ S- Bus PL S1+ S2+ S- Bus PL S1+ S2+ S- Bus PL S1+ S2+ S- 85~260VAC AC~ DIP=on,off,off A B C D DBC-4S PC6 OFF Impedance switch Multi Monitors Connection Code=0, DIP-6=off Code=1, DIP-6=off Code=14, DIP-6=off Code=15, DIP-6=on AC~ PC6 ID=

6 A B C D A B C D DBC-4S DBC-4S With DBC-4 Wiring Mode Code=15, DIP-6=on Code=14, DIP-6=on Impedance switch OFF DIP=on,off,off Code=13, DIP-6=on Code=12, DIP-6=on Code=3, DIP-6=on Code=2, DIP-6=on Impedance switch OFF DIP=on,off,off Code=1, DIP-6=on Code=0, DIP-6=on AC~ PC6 ID=

7 Electric Lock Connection Door Lock Controlled with Internal Power Note: 1. Electronic lock of Power-on-to-unlock type should be used. 2. The door lock is limited to 12V, and holding current must be less than 250mA. 3. The door lock control is not timed from Exit Button(EB). 4. The Unlock Mode Parameter of Monitor must be set to 0 (by default). connect one lock connect two locks Connect one lock Connect two locks Jumper position in 2-3 Jumper position in 2-3 BUS PL S1+ S2+ S- BUS PL S1+ S2+ S- *EB 1 ST * EB LOCK LOCK 2 nd *EB 2 nd 1 ST LOCK Door Lock Controlled with Dry Contact Note: 1. The external power supply must be used according to the lock. 2. Setup the Unlock Mode of Monitor for different lock types. Power-on-to-unlock type:unlock Mode=0 (by default) Power-off-to-unlock type:unlock Mode=1-7

8 connect one lock Take off the Jumper connect two locks Take off the Jumper BUS PL S1+ S2+ S- BUS PL S1+ S2+ S- POWER SUPPLY LOCK POWER SUPPLY LOCK LOCK Unlock parameter setting(set on ) Manual Monitor Monitor Intercom Multimedia Memory Playback Album User Setup Close 09/30/2010 Thu.16:41 1. Touch item on main menu page. 2. Touch the screen anywhere and hold for 2s. Installation settings: [0010]#:Remove all remote control [0011]#:Add remote control [8000]#:Set as master unit 0 [8001]#:Set as slaver unit 1 [8002]#:Set as slaver unit 2 [8003]#:Set as slaver unit 3 [8004]#:Set as guard unit [8005]#:Set as not guard unit [8006]#:Panel on as slaver unit called [8007]#:Panel off as slaver unit called [8008]#:Date format:mm/dd/yyyy [8009]#:Date format:dd/mm/yyyy [8010]#:Set lock mode to 0 [8011]#:Set lock mode to 1 [8021]~[8029] #Set the lock time of 1~9s Multi language settings: --- Code Number:[----] Cancel Installer setup Home Caliber TouchScreen 4.A digital keypad and setting instructions will be shown. 3. Touch Installer setup item Note: 1.must connect correctly before setting. 2. he parameter will be saved in door station automatically,so you need only set on one. 3.the above diagram is fit for icon menu series s only, to text menu series s,please refer to the corresponding user manual. -8

9 DIP Switches Setting The DIP switch is designed to set the code for door station and, there are two states for each DIP switch, please refer to the sketch map. (1) = OFF(0) = Door station DIP setting Total 2 bits can be configured, bit-1 and bit-2 are used to assign ID code for door station.the switches can be modified either before or after installation. Indoor DIP setting There are 6 bits in total. The DIP switches are used to configure the user code for Monitors. Bit-6 is an video impedance match switch, which have to be set to if match the impedance, otherwise set to OFF. Bit state Setting Bit state Setting Not match Match the video impedance Bit-1~Bit-5 are used to set user code. If the door station with one call button, the user code should be set to 0~15. If the door station with two call buttons, the user code should be set to 0~31. Please refer to the following settings: -9

10 Bit state User code Bit state User code Bit state User code code=0 code=11 code=22 code=1 code=12 code=23 code=2 code=13 code=24 code=3 code=14 code=25 code=4 code=15 code=26 code=5 code=16 code=27 code=6 code=17 code=28 code=7 code=18 code=29 code=8 code=19 code=30 code=9 code=20 code=31 code=10 code=21 Note:Monitors response button A must set the user code from 0 to 15.and button B set the user code from 16 to 31. A B A -10

11 Cables Requirements The maximum distance of the wiring is limited in the DT system. Using different cables may also affect the maximum distance which the system can reach. The farest with two or four s DBC-4S B C AC~ PC6 When Monitor quantity < 20 Cable Usage A B C Twisted cable 2x0.75 mm Twisted cable 2x1 mm A When Monitor quantity > 20 Cable Usage A B C Twisted cable 2x1 mm Twisted cable 2x1.5 mm Note:If the has been specified the distance,refer to the parameter. -11-

12 Specification Power Supply : DC 24V (supplied by PC6); Power Consumption: Standby 60mA; Working status 200mA; Camera: 1/4 ACS 4T image sensor with DSP processor Lock Power supply: 12Vdc, 300mA(Internal Power); Working temperature: -10ºC ~ +45ºC Dimension: 188(H) 110(W) 34(D)mm Precautions Please clean the unit with soft cotton cloth, don't use the organic impregnant or chemical clean agent. If necessary, please use a little pure water or dilute soap water to clean the dust. The unit is weather resistant. However do not spray high pressure water on access control keypad directly. Excessive moisture may cause problems with the unit. You must use the right adaptor which is supplied by the manufacturer or approved by the manufacturer. Pay attention to the high voltage inside the products, please refer service only to a trained and qualified professional.