Installation and Operation

Transcription

1 Installation and Operation Joystick System Controller WDS-3510CT

2 CONTENTS Contents General Information Function Description Scope of Delivery.. 3 Safety Precautions Connection and Configuration System Overview....5 Connecting the Keyboard... 7 Power Supply...8 RS485 Interface...8 Operation Key Assignment.. 9 Joystick Control General Operation Protocol/Baud Selection Exhibit Troubleshooting.. 12 Technical Specifications Dimension

3 GENERAL INFORMATION General Information Function Description This external keypad controller is used for the controlling, monitoring and programming of RS485 system products. Due to its compact size, it can be integrated everywhere harmoniously. With this keypad controller, you can control single components as well as complex CCTV systems. Clients within the RS485 BUS are selected via the numeric keypad. Contact with the corresponding client is confirmed by an acoustic signal and additionally in the keypad s info display. Messages such as target address, type of receiver and e.g. camera movements are also shown in the display. If you are using a matrix switcher, this is selected as central unit. Connected pan/tilt heads or high speed dome cameras are automatically enabled for control by the offset function integrated into the matrix switcher. It is not necessary to additionally address them directly. This keypad controller comes with a robust joystick with integrated zoom function (effected by turning the joystick). This makes it be possible to control connected pan/tilt head camera stations respectively high speed dome cameras reliably and easily. Just one hand is required for tracking an object with the connected camera unit. A potential separation with an optic-coupler (potential separator) allows trouble-free data communication on the RS485 control line. Scope of Delivery Remote control unit 3 m connection cable Power adapter 230/110 VAC to 12 VDC Junction box Operation manual 3

4 GENERAL INFORMATION Safety Precautions 1. Read these instructions carefully before connecting the components in order to avoid malfunctions and damages caused by improper installation or use. 2. Installation may only be carried out by authorized personnel according to the local safety regulations. 3. Only operate the device with the included power supply adapter and the stated operating voltage. 4. Never use the camera for other purposes except that designated. 5. Repairs and adjustments at the device may only be carried out by authorized personnel. 6. Remove the device from power supply if you do not use it for an extended period of time. 7. Immediately disconnect the device from power supply if any liquid or solid matter should get into the housing and have it checked by your authorized dealer before re-using. 8. Follow the warning notes attached to the device. 9. Only use the device in dry, dust-free and non hazardous locations. 10. Only use the device indoors. 11. In order to avoid internal heat accumulation in the device: - do not expose the device to direct sunlight. - keep sufficient distance to direct heat sources. 4

5 DVR CONNECTION AND CONFIGURATION Connection and Configuration System Overview A. Standard Connect Monitor Junction Box Dome (Indoor) CCD Matrix Switcher Controller Pan/Tilt Head Dome (Outdoor) DVR RS-485 SIGNAL FLOW VIDEO SIGNAL FLOW The following devices can be controlled with this keypad controller: - Telemetry receiver for pan/tilt head - Telemetry receiver for pan/tilt head with pre-set positions - High speed pan/tilt head - High speed dome for indoor use - High speed dome for outdoor use - Video matrix switcher (operation via RS485/232C) - Digital video recorder for High speed domes (operation via RS485) - The Controller manages directness the High speed domes 5

6 DVR CONNECTION AND CONFIGURATION B. Control via DVR Connect Junction Box Monitor Dome (Indoor) CCD Matrix Switcher Controller Dome (Outdoor) DVR RS-485 SIGNAL FLOW VIDEO SIGNAL FLOW The following devices can be controlled with this keypad controller: - Telemetry receiver for pan/tilt head - Telemetry receiver for pan/tilt head with pre-set positions - High speed pan/tilt head - High speed dome for indoor use - High speed dome for outdoor use - Video matrix switcher (operation via RS485/232C) - Digital video recorder for High speed domes (operation via RS485/232C) - The Controller uses DVR and indirectness it manages the High speed domes 6

7 CONNECTION AND CONFIGURATION Connecting the Keyboard CL 1 CL 2 CL(n-l) CL n A B CL = Client The clients are connected in a parallel way to the RS485 line (conductors A and B). Up to 32 clients with a max. connection length of 6 m can be connected to the main line. A 120Ω 120Ω B Start 1200m End The RS485 line can have a length of up to 1200 m. A transmission line with 120 Ohm has to be connected to the start and to the end of it in order to avoid signal reflections. The terminating resistor for the RS485 can be connected to each client with a jumper. 7

8 CONNECTION AND CONFIGURATION PACKING DETAIL DVR 1. CONTROLLER 2. JUNCTION BOX 3. MANUAL 4. AC ADAPTOR & POWER CORD 5. RJ45 CABLE (3m, 50cm) - Power supply Only operate the device with the power supply adapter (12VDC) included in the scope of delivery. Connect the power supply adapter to the keyboard s junction plug into the connector box. The correct power supply is signaled by the LCD display. - RS485 Interface Connect the RS485 interface with correct polarity (TRX+ and TRX-) to the junction box. 8

9 DVR OPERATION Operation This keypad controller can control all of RS485 devices. The corresponding key commands for controlling the individual devices are described in this chapter. Key Assignment Number Description

10 OPERATION Joystick Control Joystick Control Operation State Description 1 ZOOM WIDE PTZ PTZ Zoom TELE 2 ZOOM TELE PTZ PTZ Zoom WIDE 3 Menu setup Upper direction 4 Menu setup Lower direction 5 Menu setup Left direction 6 Menu setup Right direction 10

11 OPERATION General Operation Function LED Enter Clear Control Shift Select Camera Select DVR Select Monitor Pan/Tilt/Zoom Procedure LED shows the power on, shift lock or Tx/Rx status. Press ENT to select a number that has been entered. In Menu Mode, goes to previous menu with saving. Press ESC to cancel a number that has been entered. In Menu Mode, goes to previous menu without saving. If you move the joystick with CTRL key pressed, the slowest speed of pan, tilt or zoom is applied. Press SHIFT to allow the numeric keyboard to send left, right, up or down commands. If you move the joystick with this key pressed, the fastest speed of pan, tilt or zoom is applied. LCD display shows camera number in CAMERA mode. Enter camera number and press CAM to select. Enter DVR number and press DVR to select. Enter monitor number and press MON to select. Move the joystick until the camera reaches the desired position. To increase the speed of movement, move the joystick further from center. Twist the joystick clockwise to zoom in(tele), counterclockwise to zoom out(wide). TURBO speed: Move the joystick with SHIFT key pressed. Slowest speed: Move the joystick with CTRL key pressed. Lens Control (focus/iris) Presets Patterns Focus, iris - Press and hold the appropriate lens control key until the desired effect is seen. Program Position camera and then enter desired preset number (1-240) and hold down PRST for two seconds. Call Enter preset number (1-240) and press PRST to put camera in preset position. Clear Enter desired preset number (1-240) and press PRST with CTRL key pressed. Program Enter a pattern number (1-8) and hold down PTRN for two seconds. The monitor will indicate the programming function is active. Move the camera position as desired for the pattern. To save and exit the programming function, hold down PTRN for two seconds. Call (Run) Enter a pattern number and press PTRN. Move the joystick or call a preset to stop. Protocol/Baud rate Selection Enter a CAMERA address (1-999) and the press SETUP key.use numeric keys or joystick to select a protocol and/or baud rate. 11

12 EXHIBIT Exhibit Trouble shooting Please contact your authorized dealer with an exact failure description if none of the below mentioned remedy measures fixes your problem. Error Description No function Cause - Not plugged in - Connects plug of the keyboard controller not connected - Incorrectly switched 120 Ohm termination resistor No communication via RS485 interface System crash - Incorrectly assigned device address of the client - Fault in the client s power supply - Missing or incorrect cable - Incorrectly switched 120 Ohm termination resistor - If twisted pair line is not shielded, interference may occur - Moving loads are plugged incorrectly - Power supply of one (several) clients is defective 12

13 EXHIBIT Technical Specifications Application Joystick Display Housing Connection cord Operating voltage Consumption Addressing Output Operating temperature RS485 transmitter for selection and control of a maximum of 100 RS485 clients with an unlimited number of control commands Yes (pan/tilt move and zoom wide/ tele control) 16 characters x 2 line LCD Table desk housing 6 cores, 5m long, pre-assembled with Western plug 12V DC 1.4 W (7V DC) Adjustable via jumper or software RS485 interface / BUSTRONIC protocol -10 C up to + 55 C Air humidity < 90 % IP rating / class MTBF EMI / EMC / Safety Dimensions (W x H x D) Housing color Accessories (included) Weight IP40 / Class III 80,000 hours FCC / CE 342 x 165 x 96.8 mm ABS / Black operating instructions, Western socket About 690g 13

14 DIMENSION Dimension A. System Controller B. Junction Box