PRIMERGY RX600 S6. System configurator and order-information guide September PRIMERGY Server. Contents

Transcription

1 PRIMERGY RX600 S6 System configurator and order-information guide September 2014 Contents Instructions Configuration diagram Configurator 0 0 System software 1 I Basic unit 2 II Processor 3 III Memory 4 IV USB devices / optical devices 5 V Hard disk drives / SSD s 6 VI Tape Devices 7 VII Internal SAS RAID Controller 8 VIII External SCSI / SAS controller 9 IX Fibre Channel controller 10 X Communication / Network / CNA / IB 11 XI irmc S2 advanced pack / TPM 12 XII Optional PSU / Power Cord Change report PRIMERGY Server

2 PRIMERGY RX600 S6 Status Instructions This document contains basic product and configuration information that will enable you to configure your system via PC-/System-Architect Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system. You can configure your individual PRIMERGY server in order to adjust your specific requirements. The System configurator is divided into several chapters that are identical to the current price list and PC-/System-Architect. Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through the configurator by following the lines from the top to the bottom. Section III Memory, example There are X memory slots which can be equipped with XXX MB It is permissible to make up to X passes through the memory upgrade options X times S26361-XXX-XXX Memory XXX MB S26361-XXX-XXX Memory XXX MB max. X times per system max. X times per system In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x Please note that there are information symbols which indicate necessary information. Further information in the internet see: (internet) (extranet) Prices and availability see price list and PC-/System-Architect. Subject to change and errors excepted. Fujitsu PRIMERGY Server 2 of 18

3 REAR VIEW RAID Controller PCIe Slot 1 PCIe Slot 2 PCIe Slot 3 PCIe Slot 4 PCIe Slot 5 PCIe Slot 6 PCIe Slot 7 PCIe Slot 8 PCIe Slot 9 PCIe Slot 10 FRONT VIEW Slot for internal RAID Contr. PCIe 2.0 x8, 3/4 lenght, hot-plug, open end PCIe 2.0 x8, 3/4 lenght, hot-plug, open end PCIe 1.0 x4, 1/2 lenght PCIe 1.0 x4, 1/2 lenght PCIe 2.0 x16, 3/4 lenght PCIe 2.0 x8, 3/4 lenght, open end PCIe 2.0 x8, 3/4 lenght, open end PCIe 2.0 x4, 3/4 lenght PCIe 1.0 x4, 1/2 lenght PCIe 1.0 x4, 1/2 lenght MAIN BOARD Memory Board 1 ( 8 DIMM slots) Memory Board 2 ( 8 DIMM slots) Memory Board 3 ( 8 DIMM slots) Memory Board 4 ( 8 DIMM slots) Memory Board 5 ( 8 DIMM slots) Memory Board 6 ( 8 DIMM slots) Memory Board 7 ( 8 DIMM slots) Memory Board 8 ( 8 DIMM slots) Configuration diagram PRIMERGY RX600 S6 Basic Unit ( I ) Memory ( III ) System configurator and order-information guide PRIMERGY RX600 S6 Status Processor ( II ) Xeon CPU 1 Xeon CPU 2 Xeon CPU 3 Xeon CPU 4 Extension slots: external SCSI / RAID controller ( VIII ), Fiber Channel ( IX ), Communication/Network ( X ) Slot USB devices / optical devices (IV) Local View LCD Display 5.25"x 0.5" bay for CD/DVD Operating Panel Video USB USB USB Tape drives ( VI ) 5.25"x 1.6" Tape Drive UFM Hard disk drives ( V ) 2.5" SAS 2.5" SAS 2.5" SAS 2.5" SAS 2.5" SAS 2.5" SAS 2.5" SAS 2.5" SAS Servic e LAN Ethern et Ethern et Ethern et Ethern et Video COM USB USB Hot Plug Redundant Power Supply (XII) 4. PSU 3. PSU 2. PSU 1. PSU Key: Included in basic unit Option Fujitsu PRIMERGY Server 3 of 18

4 Start PRIMERGY RX600 S6 PRIMERGY RX600 S6 Status Section I Basic unit PRIMERGY RX600 S6 Systemboard with - Intel 7500 chipset with serial QPI links (Quick Path Interconnect) Rack unit 4U with - 10 PCI-Express Slots - 2 hot-plug power supplys (additional PSU as option) 2x PCIe 1.0 x4 (2x half length) - 2 memory boards (up to 6 additional boards optional) 3x PCIe 2.0 x4 (1x half length, 2x 3/4 length) - LCD-Display for LocalView (Service Display) 4x PCIe 2.0 x8 (4x 3/4 length; 2x hot plug) - 1 bay (0,5" height) for optical disc drives 1x PCIe 2.0 x16 (1x 3/4 length) - 1x 5.25" bays FH (1,6" high) for accessible drives - 4x socket for Xeon E7-28xx /-48xx processor - 8 bays for 2.5" SAS/SATA HDD`s - SATA controller on-board (for ODD) -w/o Power cord for rackmounting (ICE 320 C14->C13 plug) - irmc S2 (integrated Remote Management Controller) - no Rack- mounting kit included with graphics controller and 10/100Mbit Service LAN-port - 2x Dual-Port GBit LAN Controller on-board (4 ports, WOL-capable) Base unit Standard with - SAS RAID controller as option - 8x Fan (redundant) S26361-K1402-V400 - ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates Interfaces: Front side - 3x USB 2.0-1x VGA (15 pin) Rear Side - 2x USB 2.0-1x VGA (15 pin) - 1x RS-232-C (serial, 9 pin) - 4x on board LAN RJ45, 1x Service LAN RJ45 Internal - 1x internal USB Interfaces for backup device - 1x internal port for ussd Module (Embedded vsphere ESXi 4.0) S26361-F2735-E111 No Rackmount-Kit option Only for loose deliveries No mounting in Racks possible S26361-F2735-E285 Rack Mount Kit F2-C S7 LV telescopic rails, full extraction, toolless mounting for RMK and CMA consisting of - 1 pair of drop-in rails with CMA Adapter - lenth variable (559mm- max. 860mm for RX600) 1x per system Rack Mount Kit F2-C S7 LV length variable (559mm- 860mm) S26361-F4530-E13 S26361-F4530-E10 for loose delivery Bracket 3U in asymmetrical racks Mounting of RMK in symmetrical racks with CMA adapter S26361-F2735-E71 Cable management (no support brackets needed) S26361-F2735-E82 Rack Cable Management Arm CMA 2U S26361-F2735-L285 without CMA adapter S26361-F2735-L286 lateral f. PRIMECENTER Racks for 2U Server in racks S26361-F2735-L7 - for asymmetrical FJ racks - for symmetrical racks Sideways cable management arm or PRIMECENTER racks M1 or 3rd party racks for mounting in asymmetrical FJ racks. not for 3rd party racks Fujitsu racks Has to be mounted above the RMK. 1x per system 1x per system PRIMECENTER M1 Racks SNP:SY-F1647E301-P Installation ex works for one server or subsystem. Hereby the rack will be delivered completely pre-mounted and all wired connections are tested. PCR M1 16U, 24U, 42U: Systems and components will be delivered installed in the rack To be ordered only together with a PRIMECENTER M1 rack S26361-K827-Vxxx refer PCR M1 rack configurator max. 1x per System S26361-F2735-L82 Cable management arm 2U for asymmetrical and symetrical racks S26361-F2201-L20 Cable arm for asymmetrical and symetrical racks Has to be mounted above the RMK. S26361-F2735-L31 For mounting in asymmetrical PC racks: Support bracket 3U S26361-F2735-L31 has to be ordered for loose delivery "Rack-mounting ex factory" This service is to be ordered once per installable server/storage subsystem, in order to get the server/storage subsystem mounted into the racks. In case of the 46U PCR S2 this service has to be ordered, to get the mounting kits and the cables installed. A Fujitsu PRIMERGY Server 4 of 18

5 A PRIMERGY RX600 S6 Status Section II Processor Two CPU must be configured as minimum, as maximum 4 CPU s are possible. Later upgrading to a 3 or 4 processor system is also possible, but may require adding of PSU modules. Extension CPUs must be identical to the already installed CPU s. Following CPU s can be configured max. 4x per system As minimum two CPU s must be configured Quad-Socket CPU`s - 1x Intel Xeon processor E / E series incl. passive heat sink occupies socket for one CPU Xeon E C/12T 1.86GHz 18MB 4.80GT/s 95W S26361-F3999-E480 2x - 4x Xeon E C/16T 2.00GHz 18MB 5.86GT/s 105W S26361-F3999-E482 Xeon E C/16T 2.13GHz 24MB 6.40GT/s 105W S26361-F3999-E483 Xeon E C/20T 2.00GHz 24MB 6.40GT/s 130W S26361-F3999-E485 Xeon E C/20T 2.26GHz 24MB 6.40GT/s 130W S26361-F3999-E486 extended lead time Xeon E C/20T 2.40GHz 30MB 6.40GT/s 130W S26361-F3999-E487 extended lead time Xeon E C/8T 2.67GHz 24MB 6.40GT/s 130W S26361-F3999-E837 Following CPU s can only be configured 2x per system Two CPU s must be configured Dual socket CPUs - 1x Intel Xeon processor E series 2x incl. passive heat sink occupies socket for one CPU Xeon E C/12T 1.73GHz 18MB 4.80GT/s 105W S26361-F3999-E280 Xeon E C/20T 2.00GHz 24MB 6.40GT/s 130W S26361-F3999-E285 extended lead time RX600 S6 Architecture Memory Board 4 Memory: max. 64 DIMM Slots DDR3 LV RDIMM Memory Board 2 8x 2.5 SAS HDD SAS Riser ibbu SATA USB (3x front, ODD/ 2x rear, 1x int.) HDD IO Riser Managem. LAN Port 10/100 LAN RJ45 Memory Board 3 Memory Board 1 SAS Ctr. LSI MB RAID Key (2GB/s) ICH10 (0.5GB/s) irmc S2 (Pilot II) USB serial PORT 32MB shared Video Mem. VGA front/ rear CPU #2 Intel QuickPath Interconnect CPU #4 Xeon Xeon 75xx E7-x800 (Nehalem-EX) Xeon Xeon 75xx E7-x800 (Nehalem-EX) Xeon Xeon 75xx E7-x800 (Nehalem-EX) Xeon E7-x800 CPU #1 CPU #3 IOH #1 (Intel 7500) IOH #2 (Intel 7500) (1GB/s) (1GB/s) TPM (2GB/s) (8GB/s) 3/4 length (8GB/s) GBit Dual GB RJ45 LAN Intel GBit (Kawela) LAN RJ45 GBit Dual GB RJ45 LAN Intel GBit (Kawela) RJ45 RMII LAN 1/2 length PCIe Gen 1 x4 Slot 10 PCIe Gen2 x8 Slot 1 PCIe Gen2 x8 Slot 2 Memory Board 7 Memory Board 8 BoB Memory Board 5 Memory Board 6 (4GB/s) (4GB/s) (16GB/s) (8GB/s) (8GB/s) (4GB/s) (2GB/s) 1/2 length 3/4 length Hot-Plug Slots 1/2 length PCIe Gen2 x4 PCIe Gen2 x4 PCIe Gen2 x16 PCIe Gen2 x8 PCIe Gen2 x8 PCIe Gen2 x4 PCIe Gen1 x4 Slot 3 Slot 4 Slot 5 Slot 6 Slot 7 Slot 8 Slot 9 INTERNAL USE ONLY 7 Copyright 2011 FUJITSU TECHNOLOGY SOLUTIONS B Fujitsu PRIMERGY Server 5 of 18

6 Inter Socket Mirroring Intra Socket Mirroring 4-way interleving 2-way interleving Spare Mode BOB BOB BOB BOB Mbox 1 Mbox 2 Mbox 1 Mbox 2 BOB BOB BOB BOB BOB BOB BOB BOB Mbox 1 Mbox 2 Mbox 1 Mbox 2 BOB BOB BOB BOB BOB BOB BOB BOB Mbox 1 Mbox 2 Mbox 1 Mbox 2 BOB BOB BOB BOB BOB BOB BOB BOB Mbox 1 Mbox 2 Mbox 1 Mbox 2 BOB BOB Mbox 1 BOB BOB Mbox 2 BOB BOB BOB BOB Mbox 1 Mbox 2 System configurator and order-information guide B PRIMERGY RX600 S6 Status Section III Memory Memory configuration modes There are four different configuration modes: Independend mode (no special order code) Spare mode (S26361-F4003-E1) Interleaving mode (S26361-F4003-E2) Mirroring mode (S26361-F4003-E3) -Spare mode (S26361-F4003-E1) In spare mode, one pair of DIMMs will be spare for the other pairs. The spare DIMMs must have the same capacity or higher than the other DIMMs. DIMM sparing only relates to BOBs. There is no sparing over memory boards or CPUs. Spare Mode requires at least 2 identical set of DIMM s (with 4 Modules each). -Interleaving Mode (S26361-F4003-E2) In Interleaving mode the cache lines will be distributed over different memory boards for better performance. All DIMMS must be identical (same capacity and technology)! Three types of interleaving are available: 2-way interleaving (also called "Intra Socket Interleaving") The data are distributed over the memory controller of each CPU. This type is possible with 2, 3 or 4 CPUs and at least 2 memory boards on two CPU. Each CPU requires 1, 2, 3 or 4 set of DIMM s (with 4 Modules each). 4-way interleaving mode (also called "Inter Socket Interleaving") The data are distributed over the memory controller of two CPUs. This type is possible with 2 or 4 CPUs and 2 memory boards per CPU. Each CPU requires 1, 2 or 4 set of DIMM s (with 4 Modules each). 8-way interleaving mode (also called "Inter Socket Interleaving") The data are distributed over the memory controller of four CPUs. This type is only possible with 4 CPUs and 8 memory boards and requires 4, 8, 12 or 16 set of DIMMs (with 4 Modules each). According to the amount of installed Memory Boards and DIMMs system will be set automatically to highest possible Interleaving Mode. -Mirroring mode (S26361-F4003-E3) In mirroring mode, all data are copied within the main memory. Therefore only 50 % of the total memory is available for the operating system. Mirroring mode requires 2 memory boards per CPU. All DIMMS must be identical (same capacity and technology)! CPU Memory board Slot #1 1 Slot #3 3 CPU Memory board Memory DIMMs Board Slot #1 1 Slot #2 Slot #3 3 Slot #4 CPU Memory board Memory DIMMs Board Slot #1 1 Slot #2 Slot #3 3 Slot #4 CPU Memory board Board Slot #1 1 Slot #2 Slot #3 3 Slot #4 Memory DIMMs Memory DIMMs Spare DIMMs Spare DIMMs Data are distributed over Mboxes of each CPU Data are distributed over Mboxes of each CPU Data are distribute d over Mboxes of two CPU Mirroring from MBox to MBox on same CPU Mirroring from MBox to MBox on same CPU Two types of mirroring modes are available: Intrasocket Mirroring Memory will be mirrored from one memory controller to the other memory controller within the same CPU. Intrasocket Mirroring is possible for all CPU configurations (2, 3 or 4). Intersocket Mirroring Memory will be mirrored from one memory controller to an memory controller on another CPU (home agent to mirror agent). Intersocket mirroring is only possible with 4 CPUs (not with 2 or 3 CPUs). 1 3 CPU Memory board Board Memory DIMMs 2B 2A 2D 2C 2B 2A 2D 2C 2B 2A 2D 2C 2B 2A 2D 2C Slot Home #1 Agent Slot Mirror #2 Agent Slot Home #3 Agent Slot Mirror #4 Agent 1B 1A 1D 1C 1B 1A 1D 1C 1B 1A 1D 1C 1B 1A 1D 1C Mirroring from MBox to MBox on other CPU C Fujitsu PRIMERGY Server 6 of 18

7 C PRIMERGY RX600 S6 Status Max. Capacity / Features The system can be equipped with up to 64 DIMMs (distributed on 8 memory boards) Each DIMM slot can optionally be equipped with 4GB, 8GB, 16GB or 32GB DDR3 LV DIMM modules, so the maximal memory size is 2048 GB with 32GB modules. ECC with SDDC (Chipkill) is standard for RX600 S6. Max. Memory Speed depends on CPU QPI Speed, but is limited to 1066 MHz. S26361-F4003-E1 S26361-F4003-E2 S26361-F4003-E3 Spare Mode Installation Interleaving Mode Installation Mirrored Mode Installation BIOS setup for Spare mode BIOS setup for Interleaving mode BIOS setup for Mirrored mode Preinstallation ex factory Preinstallation ex factory Preinstallation ex factory on special release as long as available as soon as available S26361-F4523-E642 S26361-F4523-E643 S26361-F4523-E644 S26361-F4523-E645 S26361-F4523-E646 S26361-F4523-E647 Memory 16GB Memory 32GB Memory 32GB Memory 64GB Memory 128GB Memory 64GB LV RDIMM (single rank) LV RDIMM (dual rank) LV RDIMM (quad rank) LV RDIMM (quad rank) LV RDIMM (quad rank) LV RDIMM (dual rank) consisting of consisting of consisting of consisting of consisting of consisting of 4x 4GB modules 4x 8GB modules 4x 8GB modules 4x 16GB modules 4x 32GB modules 4x 16GB modules (4Gb) occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots max. 16x per system max. 16x per system max. 16x per system max. 16x per system max. 16x per system max. 16x per system on special release as long as available as soon available S26361-F4523-E642 S26361-F4523-E643 S26361-F4523-E644 S26361-F4523-E645 S26361-F4523-E646 S26361-F4523-E647 Memory 16GB Memory 32GB Memory 32GB Memory 64GB Memory 128GB Memory 64GB up to 3x LV RDIMM (single rank) LV RDIMM (dual rank) LV RDIMM (quad rank) LV RDIMM (quad rank) LV RDIMM (quad rank) LV RDIMM (dual rank) memory consisting of consisting of consisting of consisting of consisting of consisting of upgrades 4x 4GB modules 4x 8GB modules 4x 8GB modules 4x 16GB modules 4x 32GB modules 4x 16GB modules (4Gb) in base unit occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots max. 16x per system max. 16x per system max. 16x per system max. 16x per system max. 16x per system max. 16x per system Per CPU max. 2 Memory Boards can be installed S26361-F3990-E600 - with 2 CPU = max. 4 Memory boards Memory Board RX600 S6 (two included in the Base unit) for 8 DIMM modules - with 3 CPU = max. 6 Memory boards up to 6 max. 6x per system - with 4 CPU = max. 8 Memory boards additional memory boards on special release as long as available as soon as availabale with S26361-F4523-E642 S26361-F4523-E643 S26361-F4523-E644 S26361-F4523-E645 S26361-F4523-E646 S26361-F4523-E647 up to 12x Memory 16GB Memory 32GB Memory 32GB Memory 64GB Memory 128GB Memory 64GB memory LV RDIMM (single rank) LV RDIMM (dual rank) LV RDIMM (quad rank) LV RDIMM (quad rank) LV RDIMM (quad rank) LV RDIMM (dual rank) upgrades consisting of consisting of consisting of consisting of consisting of consisting of 4x 4GB modules 4x 8GB modules 4x 8GB modules 4x 16GB modules 4x 32GB modules 4x 16GB modules (4Gb) occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots max. 16x per system max. 16x per system max. 16x per system max. 16x per system max. 16x per system max. 16x per system D Fujitsu PRIMERGY Server 7 of 18

8 D PRIMERGY RX600 S6 Status Section IV USB devices / optical devices / UFM Setup RX600 S6 by SV Installation Manager is supported with following configurations: built in CD/DVD or USB CD/DVD, no Floppy disk drive: UNC Network share reachable If installation is done locally, make sure you have USB stick available for driver installation. One UFM (USB Flash Module) can be configured The UFM is bundeld with VMWare offering: VMware vsphere Embedded UFM Device S26361-F2341-E431 S26361-F3269-E2 S26361-F3641-E2 DVD-RW supermulti slim SATA Blu-ray Triple Writer slim SATA all formats, DUAL/DL, DVD-RAM 6x BD-RW, 8x DVD, 24x CD 1x only W2K, W3K and Linux BD DL and all CD/DVD formats 0.5 x 5.25", black bezel 0.5 x 5.25" E Fujitsu PRIMERGY Server 8 of 18

9 E PRIMERGY RX600 S6 Status Section V Hard disk drives SAS 6Gb/s 2.5" with hot plug/hot replace tray 300GB 10000rpm,<4,5ms, 16MB Cache S26361-F4482-E130 configuration of 450GB 10000rpm,<4,5ms, 16MB Cache S26361-F4482-E145 SAS-HDDs/SSDs requires 600GB 10000rpm,<4,5ms, 16MB Cache S26361-F4482-E160 SAS RAID controller 900GB 10000rpm,<4,5ms, 32MB Cache S26361-F4482-E190 1,2TB 10000rpm,<4,5ms, 64MB Cache S26361-F5247-E112 as soon as available 146GB 15krpm,<4,5ms, 32MB Cache 300GB 15krpm,<4,5ms, 32MB Cache 500GB 7.2krpm,<9,5ms, 64MB Cache 1TB 7.2krpm,<9,5ms, 64MB Cache max. 8x per system S26361-F4482-E514 S26361-F4482-E530 S26361-F5228-E500 S26361-F5228-E100 Solid State Disk, Mainstream Endurance* SSD SATA 6Gb/s 2.5" with hot plug/hot replace tray 100GB, Mainstream Performance S26361-F5303-E100 as soon as available 200GB, Mainstream Performance S26361-F5303-E200 as soon as available 400GB, Mainstream Performance S26361-F5303-E400 as soon as available 800GB, Mainstream Performance S26361-F5303-E800 as soon as available SSD SAS 12Gb/s 2.5" with hot plug/hot replace tray as soon as available 200GB, Enterprise Performance S26361-F5297-E200 Interface SAS12Gb/s and SAS 6Gb/s. 400GB, Enterprise Performance S26361-F5297-E400 SAS 12Gb/s support is not released 800GB, Enterprise Performance S26361-F5297-E TB, Enterprise Performance S26361-F5297-E160 *) SSD Mainstream Endurance max. 8x per system 10DWPD over 5y SSD SATA 2.5" MLC as long as stock as long as stock max. 8x S26361-F5225-E100 S26361-F5225-E200 S26361-F5225-E400 SSD 100GB SSD 200GB SSD 400GB Solid State Disk Solid State Disk Solid State Disk SATA 6Gb/s SATA 6Gb/s SATA 6Gb/s hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray max. 8x per system max. 8x per system max. 8x per system SSD SAS 2.5" SLC S26361-F4541-E100 SSD SAS 100GB, SLC Solid State Disk SAS 6Gb/s Enterprise Perfomance hot plug/hot replace tray max. 8x per system as long as stock as long as stock S26361-F4541-E400 SSD SAS 400GB, SLC Solid State Disk SAS 6Gb/s Enterprise Perfomance hot plug/hot replace tray max. 8x per system SSD SAS 2.5" MLC as long as sock as long as stock S26361-F4581-E100 S26361-F4581-E200 S26361-F4581-E400 SSD SAS 100GB, MLC SSD SAS 200GB, MLC SSD SAS 400GB, MLC Solid State Disk Solid State Disk Solid State Disk SAS 6Gb/s SAS 6Gb/s SAS 6Gb/s hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray max. 8x per system max. 8x per system max. 8x per system S26361-F4522-E351 S26361-F4522-E781 S26361-F4522-E121 PCIe-SSD 365GB MLC PCIe-SSD 785GB MLC PCIe-SSD 1.2TB MLC iodrive2 365GB iodrive2 785GB iodrive2 1.2TB max. 4x PCIe 2.0 PCIe 2.0 PCIe nm Lithography 25nm Lithography 25nm Lithography PCIe x4, Low Profile PCIe x4, Low Profile PCIe x4, Low Profile max. 4x per system max. 4x per system max. 4x per system loose delivery: S26361-F4522-L351/L781/L121 F Fujitsu PRIMERGY Server 9 of 18

10 F PRIMERGY RX600 S6 Status Section VI Tapes devices A) RDX USB3.0 Drive (connected to USB3.0 adapter card or internal USB2.0 port) USB 3.0 adapter S26361-F3749-E1 USB3.0 PCIe x1 adapter card Sunrich U-720 PCIe x1 1 port intern, 1 port extern USB 3.0 A jacks The adapter is also available as optional (loose) delivery with FH and LP bracket included S26361-F3749-L501 S26361-F3750-E4 RDX Drive USB " internal 100MB/s, USB 3.0 Connector: USB 3.0 "B" with USB cable without RDX cartridges 1.6 * 5.25", black bezel S26361-F3750-E324 RDX " 1x 100MB/s, USB 3.0 Connector: USB 3.0 "B" with USB3.0 cable with 320GB RDX cartridge RDX cartridges must be ordered separately RDX 320GB = S26361-F3857-L320 RDX 500GB = S26361-F3857-L500 RDX 1TB = S26361-F3857-L600 10x RDX320 = S26361-F3857-L329 additional RDX cartridges can be ordered RDX 320GB = S26361-F3857-L320 RDX 500GB = S26361-F3857-L500 RDX 1TB = S26361-F3857-L600 10x RDX320 = S26361-F3857-L329 The bundle is also available as optional (loose) delivery S26361-F3750-L324 with USB3.0 cable for adapter card. The USB3.0 Adapter card or the USB2.0 cable set 1.6 * 5.25", black bezel S26361-F3750-L20 must be ordered with the drive! additional RDX cartridges can be ordered S26361-F3750-E504 RDX " 100MB/s, USB 3.0 Connector: USB 3.0 "B" RDX 320GB = S26361-F3857-L320 RDX 500GB = S26361-F3857-L500 RDX 1TB = S26361-F3857-L600 10x RDX320 = S26361-F3857-L329 with USB3.0 cable The bundle is also available as optional (loose) delivery with 500GB RDX cartridge S26361-F3750-L504 with USB3.0 cable for adapter card. 1.6 * 5.25", black bezel The USB3.0 Adapter card or the USB2.0 cable set S26361-F3750-L20 must be ordered with the drive! S26361-F3750-E604 RDX " 100MB/s, USB 3.0 Connector: USB 3.0 "B" additional RDX cartridges can be ordered RDX 320GB = S26361-F3857-L320 RDX 500GB = S26361-F3857-L500 RDX 1TB = S26361-F3857-L600 10x RDX320 = S26361-F3857-L329 with USB3.0 cable with 1TB RDX cartridge The bundle is also available as optional (loose) delivery 1.6 * 5.25", black bezel S26361-F3750-L604 with USB3.0 cable for adapter card. The USB3.0 Adapter card or the USB2.0 cable set S26361-F3750-L20 must be ordered with the drive! B) DDS USB Drive (connectet to internal USB port) S26361-F3324-E4 S26361-F3325-E4 Tape drive DDS Gen5 USB 5.25" Tape drive DDS Gen6 USB 5.25" 36GB, 3MB/s, USB GB, 6MB/s, USB 2.0 Connector: USB "B" Connector: USB "B" with USB cable incl. description (Ger/US) with USB cable incl. description (Ger/US) data and cleaning cartridge data and cleaning cartridge 1.6 * 5.25", black bezel 1.6 * 5.25", black bezel C) LTO SAS Drive (connected with PCIe SAS controller) S26361-F3257-E4 4 port SAS RAID Controller LSI MegaRAID SAS 1064 no Cache, no BBU RAID 0, 1 & 1E SAS 3Gb/sec 4 internal ports PCIe x4, 160mm as soon as available S26361-F3561-E4 S26361-F3626-E2 S26361-F3627-E1 S26361-F3787-E1 Tape drive LTO3HH Ultrium SAS Tape drive LTO4HH Ultrium SAS Tape drive LTO5HH Ultrium SAS Tape drive LTO6HH Ultrium SAS 400GB, 60MB/s, SAS 3Gb 800GB, 120MB/s, SAS 6Gb 1500GB, 140MB/s, SAS 6Gb 2500GB, 160MB/s, SAS 6Gb Connector: mini-sas Connector: SATA Connector: mini-sas Connector: mini-sas incl. SAS cable incl. SAS cable incl. SAS cable incl. SAS cable incl. description (Ger/US) incl. description (Ger/US) incl. description (Ger/US) incl. cleaning cartridge data and cleaning cartridge data and cleaning cartridge data and cleaning cartridge without data cartridge 1.6 * 5.25", black bezel 1.6 * 5.25", black bezel 1.6 * 5.25", black bezel 1.6 * 5.25" G Fujitsu PRIMERGY Server 10 of 18

11 G PRIMERGY RX600 S6 Status Section VII internal SAS RAID 0/1 and RAID5 Controller for HDD s as long as available S26361-F3554-E8 S26361-F3669-E2 S26361-F3669-E3 RAID Ctrl SAS 6G 8port internal RAID Ctrl SAS 6G 8port internal RAID Ctrl SAS 6G 8port internal Based on chip LSI SAS 2008 RAID Controller must be ordered, Based on chip LSISAS2208 Based on chip LSISAS2208 LSI MegaRAID if at least one internal HDD is configured! LSI MegaRAID LSI MegaRAID no Cache, no BBU 1GB Cache with ECC 1GB Cache with ECC RAID 0, 1 & 1E RAID 0, 1, 10, 5, 50, 6, 60 RAID 0, 1, 10, 5, 50, 6, 60 Support for 3Gb/s and 6Gb/s optional FBU optional FBU SATA and SAS hard drives Support for 3Gb/s and 6Gb/s Support for 3Gb/s and 6Gb/s PCIe x4 SATA and SAS hard drives SATA and SAS hard drives Low-profile MD2 form factor PCIe x8 PCIe 3.0 x8 Low-profile MD2 form factor Low-profile MD2 form factor Loose delivery RAID Advanced Software Option S26361-F3669-L660 RAID Advanced Software Options License Activation Key for CacheCade 2.0 and FastPath for 1 Controller S26361-F3669-E660 RAID Advanced Software Options License Activation Key for CacheCade 2.0 and FastPath for 1 Controller 1x S26361-F3669-E100 S26361-F3554-E512 TFM Module for FBU option RAID Ctrl SAS 6G 8port internal (flash and FBU control logic) Based on chip LSI SAS 2108 max. 1x per Controller LSI MegaRAID 512MB Cache with ECC RAID 0, 1, 10, 5, 50, 6, 60 optional BBU S26361-F3669-E155 Flash Backup Unit Support for 3Gb/s and 6Gb/s Flash Backup Unit requires modified SATA and SAS hard drives with 55cm cable set system unit PCIe x4 max. 1x per Contr., 2x per System with serial number Low-profile MD2 form factor YLCE Lose delivery TFM/ FBU option S26361-F3257-E170 Cache Battery Backup Unit with 70cm cable set max. 1x per controller S26361-F3669-L100 TFM Module for FBU option (flash and FBU control logic) max. 1x per Controller BBU max. 2x per system possible for loose delivery please order S26361-F3257-L110 S26361-F3669-L110 Flash Backup Unit with 25, 55, 70 cable set max. 1x per Controller H Fujitsu PRIMERGY Server 11 of 18

12 G PRIMERGY RX600 S6 Status Section VIII external SCSI / SAS controller B. SAS controller for external backup drives max. 3x S26361-F3628-E1 SAS Controller 6Gb/s 8 port LSI SAS9200-8e PCIe 2.0 x4, ext: 8 port max. 2x per system C. SAS RAID controller for JBOD subsystems as soon as available as soon as available S26361-F3593-E3 S26361-F3713-E3 8 port SAS 6G RAID Controller RAID Ctrl SAS 6G 8port external LSI The RAID controller can be used only for the connection of LSI MegaRAID SAS e MegaRAID SAS9280-8e 6Gb/s external subsystems (FibreCAT SX40, Eternus JX40) 1GB Cache with ECC 512MB Cache with ECC RAID 0, 1, 5, 6, 10, 50 & 60 RAID 0, 1, 10, 5, 50, 6 & 60 Cables for the connection from the RAID Controllers without FBU without ibbu to the subsystem see configurator FibreCAT SX40 SAS 6Gb/sec SAS 6Gb/sec The usage of the internal SAS ports is not supported! 8 port external max. 2x 8 port external PCIe 3.0 x8, MD2 form factor PCIe x4, 167mm Lose delivery FBU option full height bracket full height bracket S26361-F3669-L110 max. 2x per system max. 2x per system Flash Backup Unit with 25, 55, 70 cable set max. 1x per Controller S26361-F3669-E125 S26361-F3257-E170 Flash Backup Unit Cache Battery Backup Unit BBU max. 2x per system possible with 25cm cable set with 70cm cable set for loose delivery please order max. 1x per Controller max. 1x per controller S26361-F3257-L110 Loose delivery RAID Advanced Software Option S26361-F3669-L661 RAID Advanced Software Options License Activation Key for CacheCade 2.0 and FastPath for 1 Controller S26361-F3669-E661 RAID Advanced Software Options License Activation Key for CacheCade 2.0 and FastPath for 1 Controller P Fujitsu PRIMERGY Server 12 of 18

13 P System configurator and order-information guide PRIMERGY RX600 S6 Status Section IX Fibre Channel S26361-F3631-E1 Qlogic S26361-F3631-E2 Emulex No mix of different vendors for FC or FCoE controllers. 8GBit/s FC Controller 8GBit/s FC Controller Qlogic Qlogic loose delivery: QLE2560, full height bracket QLE2562, full height bracket Single channel S26361-F3631-L1 1 channel 8GBit/sec FC Controller 2 channel 8GBit/sec FC Controller Dual Channel S26361-F3631-L2 LC Interface for 50µm Fiber LC Interface for 50µm Fiber with mounted LP bracket PCIe x8, 170mm PCIe x8, 170mm FH bracket is not included max. 6x per system max. x per system S26361-F3961-E1 S26361-F3961-E2 8GBit/s FC Controller 8GBit/s FC Controller Emulex Emulex loose delivery: LPe1250, full height bracket LPe12002, full height bracket Single channel S26361-F3961-L1 1 channel 8GBit/sec FC Controller 2 channel 8GBit/sec FC Controller Dual Channel S26361-F3961-L2 LC Interface for 50µm Fiber LC Interface for 50µm Fiber with mounted LP bracket PCIe x4, 170mm PCIe x4, 170mm FH bracket is not included max. 6x per system max. 6x per system as soon as available as soon as available S26361-F4994-E1 S26361-F4994-E2 16GBit/s FC Controller 16GBit/s FC Controller Emulex Emulex loose delivery: LPe16000, low profile bracket LPe16002, low profile bracket Single channel S26361-F4994-L501 1 channel 16GBit/sec FC Contr. 2 channel 16GBit/sec FC Contr. Dual Channel S26361-F4994-L502 LC Interface for 50µm Fiber LC Interface for 50µm Fiber contains LP and FH brackets. PCIe x8, 170mm PCIe x8, 170mm max. 8x per system max. 8x per system All controllers for the connection of external storage systems are delivered without cables. For the configuration of external cabling see the configurator for external storage systems. For Fibre Channel SAN also other componets like switches, SFPs and optical wires are orderable (for details see price liste) Q Fujitsu PRIMERGY Server 13 of 18

14 I PRIMERGY RX600 S6 Status Section X Communication / Network / CNA / IB on-board LAN Controller 2x Dual Gbit Ethernet Contr. on-board Intel NS (Kawela wo/ipsec) ext: 4x RJ45 connector, Cat 5 Teaming: Failover, Load Balancing The Intel LAN Controllers Pro 1000MT, 1000MF, 1000PT, 1000PF can be used with the on-board controller in Teaming Mode Two onboard LAN ports can likewise educate a team. 1Gbit/s Ethernet Adapter S26361-F4610-E2 S26361-F4610-E4 (I350-T2) (I350-T4) Gbit Ethernet Controller Dual 1000TX Gbit Ethernet Controller Quad 1000TX PLAN CP 2x1Gbit Cu Intel I350-T2 PLAN CP 4x1Gbit Cu Intel I350-T4 4x Intel Powerville based 2 port Server Ad. Intel Powerville based 4 port Server Ad. PCIe x4, Low Profile PCIe x4, Low Profile full height (FH) bracket full height (FH) bracket ext: for RJ45-plug, Cat 5 ext: for RJ45-plug, Cat 5 max. 4x per system max. 4x per system Loose delivery with FH and LP bracket: I350-T2 S26361-F4610-L502 I350-T4 S26361-F4610-L504 I1 Fujitsu PRIMERGY Server 14 of 18

15 I1 PRIMERGY RX600 S6 Status Gbit/s Ethernet Adapter S26361-F3629-E2 S26361-F3752-E2 (D2755) (Intel X540-T2) 10 Gigabit Ethernet Contr. dual port SFP+ Eth Ctrl 2x10GBase-T Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+ Intel Twinville based 2 port Server Ad. Intel Niantic based dual port 10Gb NIC PCIe x4, Low Profile PCIe x8, Low Profile, Full Height Bracket Full Height (FH) bracket ext: 2x SFP+ cage ext: for RJ45-plug, Cat 6 max. 4x per system max. 2x per system S26361-F3986-E3 S26361-F3986-E4 V:TWX Connector-PY SFP+ Module MMF 10GbE LC SFP+ Module SMF 10GbE LC for all Twinax (FTS,BR,CI) SFP+ module for 10 Gbit SFP+ module for 10 Gbit max. 2x per controller 6x 2x Ethernet 50µm FO cabling Ethernet 9µm FO cabling ext:lc-sr-connector ext:lc-lr-connector max. 2x per controller max. 2x per controller The SFP+ modules are also available as loose delivery S26361-F3986-L3 S26361-F3986-L4 Instead SFP+ Modules, SFP+ twinax cables from the switch vendors may be used S26361-F3989-E600 *) S26361-F3873-E500 *) S26361-F4571-E500 *) *) in SA only SFP+ active twinax cable SFP+ active twinax cable SFP+ passive twinax cable shown in customized twinax cable for customized twinax cable for customized twinax cable for cabling view full rack setup ex factory full rack setup ex factory full rack setup ex factory cable length is selected by cable length is selected by cable length is selected by requirement in the factory requirement in the factory requirement in the factory Fujitsu branded cable Brocade branded cable Cisco branded cable max. 2x per controller max. 2x per controller max. 2x per controller 6x separate orderable 10Gb Ethernet cables S26361-F3989-L102 SFP+ active Twinax Cable Fujitsu 2m The controller D755 is delivered without SFP+ modules for optical S26361-F3989-L105 SFP+ active Twinax Cable Fujitsu 5m cables, these must be ordered separately. S26361-F3989-L110 SFP+ active Twinax Cable Fujitsu 10m Loose delivery options (FH and LP bracked included) S26361-F3873-L501 SFP+ active Twinax Cable Brocade 1m D2755 S26361-F3629-L502 S26361-F3873-L503 SFP+ active Twinax Cable Brocade 3m X540-T2 S26361-F3752-L502 S26361-F3873-L505 SFP+ active Twinax Cable Brocade 5m S26361-F4571-L101 S26361-F4571-L103 S26361-F4571-L105 S26361-F4571-L107 SFP+ passive Twinax Cable Cisco 1m SFP+ passive Twinax Cable Cisco 3m SFP+ passive Twinax Cable Cisco 5m SFP+ active Twinax Cable Cisco 7m while stocks last S26361-F4571-L110 SFP+ active Twinax Cable Cisco 10m S26361-F3592-E2 10GBit/s CNA Emulex OCe channel 10GBit/sec CNA SFP+ Cage PCIe x8, 170mm max. 6x per system S26361-F3592-E108 SFP+ Module MMF 10GbE LC SFP+ module for 10 Gbit V:TWX Connector-PY The SFP+ Module is also available as loose delivery Ethernet FO cabling for all Twinax (FTS,BR,CI) S26361-F3592-L108 ext:lc-connector max. 2x per controller Instead SFP+ Modules, SFP+ twinax cables from max. 2x per controller the switch vendors may be used 2x S26361-F3989-E600 *) S26361-F3873-E500 *) S26361-F4571-E500 *) *) in SA only SFP+ active twinax cable SFP+ active twinax cable SFP+ passive twinax cable shown in customized twinax cable for customized twinax cable for customized twinax cable for cabling view full rack setup ex factory full rack setup ex factory full rack setup ex factory cable length is selected by cable length is selected by cable length is selected by requirement in the factory requirement in the factory requirement in the factory Fujitsu branded cable Brocade branded cable Cisco branded cable max. 2x per controller max. 2x per controller max. 2x per controller I2 separate orderable 10Gb Ethernet cables S26361-F3989-L102 SFP+ aktives Twinax Kabel Fujitsu 2m S26361-F3989-L105 SFP+ aktives Twinax Kabel Fujitsu 5m S26361-F3989-L110 SFP+ aktives Twinax Kabel Fujitsu 10m S26361-F3873-L501 SFP+ aktives Twinax Kabel Brocade 1m S26361-F3873-L503 SFP+ aktives Twinax Kabel Brocade 3m S26361-F3873-L505 SFP+ aktives Twinax Kabel Brocade 5m S26361-F4571-L101 SFP+ passives Twinax Kabel Cisco 1m S26361-F4571-L103 SFP+ passives Twinax Kabel Cisco 3m S26361-F4571-L105 SFP+ passives Twinax Kabel Cisco 5m S26361-F4571-L107 SFP+ aktives Twinax Kabel Cisco 7m S26361-F4571-L110 SFP+ aktives Twinax Kabel Cisco 10m Fujitsu PRIMERGY Server 15 of 18

16 I2 PRIMERGY RX600 S6 Status G) Infiniband HCA's max. 4x S26361-F4475-E102 IB HCA 40Gb 1 port QDR IB HCA 1x 40Gb PCIe 2.0 (5,0GT/s) PCIe x8, low profile ext: 1x QSFP-connector max.4x per system Low Profile PCIe form factor with exchangeable Full Height (FH) or Low Profile (LP) bracket S26361-F3996-E500 only within a rack If additional length of copper cable or optical cable are needed, InfiniBand Cu Cable 40Gb configuration then they must be ordered from the cable vendor directly customized Copper cable are also available for loose delivery as QSFP, 1m and 3m S26361-F3996-L561, QSFP, 56Gb, 1m max. 1x per adapter S26361-F3996-L563, QSFP, 56Gb, 3m J Fujitsu PRIMERGY Server 16 of 18

17 J PRIMERGY RX600 S6 Status Section XI System Management Products (RemoteView) S26361-F1790-E241 irmc S2 advanced pack integrated remote management controller activation key for graphical console redirection and remote media redirection S26361-F3552-E1 TPM Module Trusted Platform Module on Motherboard Use according to import restrictions Be aware of import restrictions! Loose delivery for later integration possible for customer. S26361-F3552-L1 TPM Module add-on kit for later integration (loose delivery) Trusted Platform Module on Motherboard Use according to import restrictions Section XII Optional PSU / Power cords / Region kit In addition to the base configuration with two power supplies units (1+1 redundancy) max. two addition PSU s can be installed. Configurations with more than 2 CPU s or more than 2 memory boards requiring one additional PSU (2+1 redundancy). For configurations with more than 6 memory boards or if phase redundancy/dual power feed is requested two additional PSU s needed. (3+1 or 2+2 redundancy). For later upgrade the following kit is available: S26113-F561-E20 S26113-F561-L20 3nd / 4rd power supply module 3nd / 4rd power supply module 850W, hot plug 850W, hot plug for max. configuration for max. configuration w/o 1x power cord ICE320 C14->C13 w/o 1x power cord ICE320 C14->C13 max. 2x per system max. 2x per system S26361-F3301-E123 Certification for India For shipments to India mandatory! Hint: No country specific powercord configurable with Certification for India Power cord options (1x per PSU) max. 4 x T26139-Y1968-E100 Powercord for rack, 4m, grey, Power cord has to be ordered separately IEC 320 C14->C13 connector T26139-Y1742-E10 USA, Canada, 1.8m, grey T26139-Y3850-E10 Option "no powercord", for Countries without specific cable orderable like e.g. China S26361-F1452-E100 S26361-F1452-E110 S26361-F1452-E130 REGION KIT APAC/EMEA/India REGION KIT JP REGION KIT America For Shipments to Asia pacific, For Shipments to Japan regions For Shipments to America EMEA or India regions 1x per system 1x per system 1x per system End PRIMERGY RX600 S6 Fujitsu PRIMERGY Server 17 of 18

18 PRIMERGY RX600 S6 Status Change Report Date Order number Changes S26361-F2735-E82 defined as can -position to RMK S26361-F3301-E123 Added certification for India S26361-F3592-E2 phase out OCe10102 EOL D3035 S26361-F3739-xxx EOL D S26361-F3740-xxx EOL D S26361-F3242-xxx EOL Sheepshead Bay S26361-F3531-E2 deleted S26361-F3739-E201 phase out S26361-F3740-E201 phase out S26361-F3610-E202 EOL S26361-F5247-E112 New 1.2TB 2.5" SAS 10K HDD added S26361-F5303-* New SATA SSDs added S26361-F5297-* New SAS SSDs added Optional USB Comps no longer available S26361-F4610-E2 / -E4 added new 1Gb NICs from Intel S26361-F4482-E* HDD Cache updated S26361-F3787-E1 LTO6 added 8x as max. total number of FC controller removed S26361-F3669-E125 FBU option of S26361-F3713-E3 changed from -E170 to -E125 (25cm FBU cable) S26361-F3669-E3 RAID Ctrl SAS 6G 1GB (D3116C) added S26361-F3750-E324/504/E604 RDX & Cartridge bundles added S26361-F3669-E660/L660 RAID Advanced Software Options: Bypass for E660; L660 added S26361-F3669-E661/L661 RAID Advanced Software Options for RAID Ctrl SAS 6G 8port external added S26361-F3593-E1 Changed to S26361-F3593-E3 and set as soon as available S26361-F3271-E1 SAS Controller 3Gb/s 8 port is EOL => removed S26361-F3270-E1 SCSI U320 extern is EOL => removed S26361-F5228-E*** New 2.5" BC SAS 7.2K HDD F3749-E4 and F3750-E4 "as soon as available" removed S26361-F3857-E4 "as long as available" added S26361-F3669-E2 Oder number for 6G RAID Controller changed from -E3 to -E S26361-F5423-E647 Added 64 GB Memory S26361-F3749-Ex Added USB 3.0 Adapter S26361-F3750-Ex Added RDX Drive S26361-F3986-E4 New SFP+ Module SMF 10GbE LC S26361-F4541-E200 EOL: 200GB SSD SAS SLC /-L285 /-L286 added new Rackmount Kit with vario carrier mm, rails with and without CMA adapter S26361-F3739-E1 added new LAN Controller (D3035 / D3045) S26361-F2735-E285 Change to new RMK S26361-F3669-E3 Oder number for Cougar3 changed to -E S26361-F4523-E646 Add 128GB / 4x 32GB Memory Module S26361-F4581-Exxx Add SSD SAS MLC S26361-F3857-L160/L169 RDX Cartridge 160GB is EOL => removed S26361-F4522-xxx PCIe-SSD 781GB / 1,2TB MLC added S26361-F5225-E*00 New order for SATA SSD s S26361-F3669-E1 new int. SAS RAID Controller added S26361-F3713-E1 new ext. SAS RAID Controller added S26361-F3641-E2 new Blue-ray Triple Writer added S26361-F4482-E114 SAS HD 6G 144GB - no longer available S26361-F4541-Ex00 new SAS SSD with 100, 200, 400 GB added - as soon as available S26361-F3298-E64 64 GB SSD - no longer available Mixmatch between Emulex FC controllers and FCoE Controller now possible S26361-F3601-Exxx BC-SATA HDD removed S26361-F2735-E245 Cable Management Arm changed PSUs changed, Power cables added, Region Kit added S26361-F3986-E3 SFP modules for 10GbE adapter changed S26361-F4522-Exxx PCIe SSD added S26361-F4475-Ex02 max. Number of Infiniband HCA s increased to 4x each / 4 x total S26361-F3626-E2 order number LTO4 changed Blu-ray Triple Writer slim SATA and DVD-ROM slim SATA added LTO2 removed Update: RMK, Memory Order codes / 10Gb Controller CPU SKUs updated First draft Fujitsu PRIMERGY Server 18 of 18