2000~6000W Front End Power System RKP-1U Rack System

Transcription

1 000~6000W Front End Power System RKP-U Rack System SELECTI GUIDE Rack: RKP-U I C Whole System: RKP-6KU I C - Output voltage C: With RCP-CMU- C: With RCP-CMU- -: Without RCP-CMU- -: Without RCP-CMU- I: AC Inlet (IEC30-C0) I: AC Inlet T: Terminal block T: Terminal SPECIFICATI - Rack System MODEL OUTPUT INPUT FUNCTI ENVIRMENT SAFETY & EMC (Note 4) OTHERS NOTE MODULE RACK OUTPUT VOLTAGE MAX. OUTPUT CURRENT MAX. OUTPUT POWER Note W VOLTAGE RANGE RKP-6KU - RKP-6KU -4 RKP-6KU -48 RCP-000- RCP RCP RKP-UI or RKP-UT V 300A Note.5 90 ~ 64VAC 7 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz AC CURRENT (Typ.)FOR EACH UNIT 3A/5VAC 7A/30VAC 6A/5VAC A/30VAC 6A/5VAC A/30VAC LEAKAGE CURRENT <3.5mA / 30VAC AUXILIARY POWER 0.3A, 0.8A REMOTE /OFF CTROL By electrical signal or dry contact :short OFF:open REMOTE SENSE DC OK SIGNAL AC FAIL SIGNAL OUTPUT VOLTAGE TRIM OVER TEMP WARNING FAN FAIL SIGNAL WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATI SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATI RESISTANCE EMC EMISSI EMC IMMUNITY The isolated TTL signal out, refer to function manual The isolated TTL signal out, refer to function manual -40 ~ +70 (Refer to "Derating Curve") 0 ~ 90% RH non-condensing -40 ~ +85, 0 ~ 95% RH 0.03%/ (0 ~ 50 ) 40A 5760W 0 ~ 500Hz, G 0min./cycle, 60min. each along X, Y, Z axes UL60950-, TUV EN approved I/P-O/P:3KVAC I/P-FG:.5KVAC O/P-FG:0.7KVDC DIMENSI Rack 483.6*350.8*44(L*W*H) PACKING.5Kg; pcs/.5kg/.67cuft 48V 6A 6048W Compensate voltage drop on the load wiring up to 0.5V. "Local Sense"should be connected in order to get the correct output voltage if the "Remote Sense"is not used Adjustment of output voltage, possible between 90 ~ 0% of rated output Logic " High" for over temperature warning, refer to function manual, isolated signal 4V The isolated TTL signal out, refer to function manual I/P-O/P, I/P-FG, O/P-FG:00M Ohms / 500VDC / 5 / 70% RH Compliance to EN550 (CISPR) Conduction Class B, Radiation Class A ; EN ,-3 Compliance to EN ,3,4,5,6,8,, EN (EN5008-), heavy industry level, criteria A File Name:RKP-U RACK SYSTEM-SPEC

2 000~6000W Front End Power System RKP-U Rack System Mechanical Specification (Rack System) Case No. 959A Unit:mm Fig RKP-UT C B - + A CN500 JK Fig FG FG FG N N N L L L C B - + A CN500 JK RKP-UI Mounting Bracket IEC30-C0 IEC30-C0 IEC30-C M5 L=6mm SVR SVR SVR 3-M5 L=6mm Air flow direction Module C Module B Module A DC OK DC OK DC OK File Name:RKP-U RACK SYSTEM-SPEC

3 000~6000W Front End Power System RKP-U Rack System CN500 Pin No. Assignment Connector Pin No. Assignment(CN500) : D-Type Right Angle 5 positions Pin No. Assignment Pin No. Assignment Pin No. Assignment Pin No. Assignment Pin No. Assignment /OFF-A 6 FAN FAIL-A T-ALARM-B 6 /OFF-C FAN FAIL-C AC-OK-A 7 /OFF-B FAN FAIL-B 7 AC-OK-C 3 DC-OK-A 8 AC-OK-B 3 +5V-AUX 8 DC-OK-C 3 -S 4 5 PV-A T-ALARM-A 9 0 DC-OK-B PV-B 4 5 -AUX GND-AUX 9 0 PV-C T-ALARM-C 4 5 JK Pin No. Assignment Connector Pin No. Assignment(CN ) : RJ45 8 positions Pin No. Assignment Pin No. Assignment Pin No. Assignment DA 4 CTROL 7 SCL DB 5 NC 8 GND-AUX 3 6 SDA CN500 IN/OUT Connector pins function description Pin No. Function,7,6,8,7 3,9,8 4,0,9 5,,0 6,, /OFF AC-OK DC-OK PV T-ALARM FAN FAIL +5V-AUX -AUX GND-AUX 3 -S 4 5 Each unit can separately turn the output on and off by electrical signal or dry contact between /OFF A,B,C(pin,7,6) and +5V-AUX(pin 5). Short:, Open:OFF. (Note.) Low : When the input voltage is 87Vrms. High : when the input voltage in 75Vrms. (Note.) High : When the Vout 80 5%. Low : When Vout 80 5%. (Note.) Connection for output voltage trimming. The voltage can be trimmed within its defined range. (Note.) High : When the internal temperature (TSW or TSW open) exceeds the limit of temperature alarm. Low : When the internal temperature (TSW or TSW short) under the limit temperature. (Note.) High : When the internal fan fail. Low : When the internal fan is normal. (Note.) Auxiliary voltage output, 4.5 ~ 5.5V, referenced to GND- AUX (pin 5). The maximum load current is 0.3A. This output has the built-in "Oring diodes" and is not controlled by the remote /OFF control. Auxiliary voltage output, 0.8 ~ 3.V, referenced to GND- AUX (pin 5). The maximum load current is 0.8A. This output has the built-in "Oring diodes" and is not controlled by the remote /OFF control. Auxiliary voltage output GND. The signal return is isolated from the output terminals ( & ). Positive sensing. The signal should be connected to the positive terminal of the load. The and -S leads should be twisted in pair to minimize noise pick-up effect. The maximum line drop compensation is 0.5V. Negative sensing. The -S signal should be connected to the negative terminal of the load. The -S and leads should be twisted in pair to minimize noise pick-up effect. The maximum line drop compensation is 0.5V. Positive output voltage. For local sense use only, can't be connected directly to the load. Negative output voltage. For local sense use only, can't be connected directly to the load. JK IN/OUT Connector pins function description Pin No., Function DA,DB CTROL NC SDA SCL GND-AUX Differential digital signal for parallel control. (Note.) Negative output voltage. For parallel control, can't be connected directly to the load. Remote /OFF control pin used in the PMBus interface. (Note.) Not use. Serial Data used in the PMBus interface. (Note.) Serial Clock used in the PMBus interface. (Note.) Auxiliary voltage output GND. The signal return is isolated from the output terminals ( & ). Note.: Non-isolated signal, referenced to the output terminals (). Note.: Isolated signal, referenced to GND-AUX. File Name:RKP-U RACK SYSTEM-SPEC

4 File Name:RKP-U RACK SYSTEM-SPEC ~6000W Front End Power System RKP-U Rack System Function Manual. Remote /OFF Control The PSU can be turned /OFF together or separately by using the "Remote /OFF" function. RKP-U /OFF A /OFF B /OFF C 7 /OFF A 7 6 /OFF B 6 /OFF C RKP-U Between /OFF and +5V-AUX SW Open Output OFF +5V-AUX V-AUX SW Short. Voltage Drop Compensation. Remote Sense The remote sense compensates voltage drop on the load wiring up to 0.5V. RKP-U -S 3 LOAD Sense lines should be twisted in pairs. Local Sense Notice : The,-S have to be connected to the, terminals locally in order to get the correct output voltage if the remote sensing is not used. RKP-U -S Output Voltage TRIM ()Connecting an external DC source between PV(4,0,9) and (5) on CN500 that is shown in Fig. 3.. ()Adjustment of output voltage is possible between 90~0%(Typ.) of the rated output which is shown in Fig. 3.. Reducing output current is required when the output voltage is trimmed up. 4,0,9 PV 0~5V 5 Fig. 3. Add on 0~5V external voltage OUTPUT VOLTAGE(%) Vout V OUTPUT CURRENT (%) V EXTERNAL VOLTAGE(DC) OUTPUT VOLTAGE (%) Fig. 3. Output voltage trimming 4. Front Panel Indicators & Corresponding Signal at Function Pins Function AC-OK AC-NG DC-OK DC-NG T-OK T-ALARM LED GREEN When input voltage 87V RED When input voltage 75V GREEN When output voltage 80% 5% of Vo rated. RED When output voltage 80% 5% of Vo rated. GREEN RED When the internal temperature (TSW & TSW short) is within safe limit When the internal temperature (TSW or TSW open) exceeds the limit of temperature alarm *Signal between function pin and "GND-AUX". * Signal 0~0.5V 4.5 ~ 5.5V 0~0.5V 4.5 ~ 5.5V 0~0.5V 4.5 ~ 5.5V PSU Output OFF OFF

5 000~6000W Front End Power System RKP-U Rack System 5.PMBus communication interface 5. Interface specification RCP-000 support PMBus Rev.. with maximum 00kHz bus speed. 5. Device Address (A0~A4) MSB LSB 0 A4 A3 A A A0 The device address can be defined by using DIP switch and shows below. The DIP switch down position is logic "" and up position is logic "0". Module DIP switch position Module DIP switch position No No OFF 7 OFF OFF 8 OFF 3 OFF OFF 9 OFF OFF 4 OFF 0 OFF 5 OFF OFF OFF OFF 6 OFF OFF OFF OFF 7 OFF OFF OFF 3 OFF OFF OFF 8 OFF 4 OFF 9 OFF OFF 5 OFF OFF 0 OFF OFF 6 OFF OFF OFF OFF OFF 7 OFF OFF OFF OFF OFF 8 OFF OFF 3 OFF OFF OFF 9 OFF OFF OFF 4 OFF OFF OFF 30 OFF OFF OFF 5 OFF OFF OFF OFF 3 OFF OFF OFF OFF 5.3 Summary (ref. to PMBus Rev..) Code 0h OPERATI Name Transaction Type R/W Byte # of data Bytes Remote /OFF control 0h _OFF_CFIG Read Byte /OFF function configuration 9h 0h CAPABILITY VOUT_MODE Read Byte Capabilities of a PMBus device Define data format for output voltage h h 46h VOUT_COMMAND VOUT_TRIM IOUT_OC_FAULT_LIMIT R/W Word R/W Word Output voltage setting value Output voltage trimming value Output overcurrent setting value 47h IOUT_OC_FAULT_RESPSE Define protection and response when an output overcurrent fault occurred 79h STATUS_WORD Summary status reporting 7Ah STATUS_VOUT Output voltage status reporting 7Bh STATUS_IOUT Output current status reporting 7Ch STATUS_INPUT AC inpit voltage statusreporting 7Dh STATUS_TEMPERATURE Temperature status reporting File Name:RKP-U RACK SYSTEM-SPEC

6 000~6000W Front End Power System RKP-U Rack System Code 80h 8h 88h 8Bh 8Ch 90h 9h 98h 99h 9Ah 9Bh 9Ch 9Dh 9Eh Name STATUS_MFR_SPECIFIC STATUS_FANS READ_VIN READ_VOUT READ_IOUT READ_FAN_SPEED_ READ_FAN_SPEED_ PMBUS_REVISI MFR_ID MFR_MODEL MFR_REVISI MFR_LOCATI MFR_DATE MFR_SERIAL Transaction Type Block Read Block Read Block Read Block R/W Block R/W Block R/W # of data Bytes 8Dh READ_TEMPERATURE_ Manufacturer's name Manufacture specific status reporting Fan and status reporting AC input voltage reading value (format: Linear, N=-) Output voltage reading value Output current reading value (format: Linear, N= -3) Temperature reading value (format: Linear, N= -3) Fan speed reading value (format: Linear, N= 4) Fan speed reading value (format: Linear, N= 4) The compliant revision of the PMBus (default: h for Rev..) Manufacturer's model name Firmware revision Manufacturer's factory location Manufacture date. (format: YYMMDD) Product serial number File Name:RKP-U RACK SYSTEM-SPEC