JOYSTICK CONTROLLER USER'S MANUAL MANUAL NUMBER

Transcription

1 JOYSTICK CONTROLLER JAD-832 USER'S MANUAL MANUAL NUMBER Ultrak, Inc Coonpath Road NW Carroll, OH (740) (800) FAX (740)

2 Revision A - Corrected page 3-18 Revision B - Deleted SmartScan Programmer, added COE-08A/16A, updated DIA-01 drawing, added CRX-800 auxiliary control function, updated FUN>FUN>3 and FUN>FUN>4 commands for error log Revision C - corrected procedure for camera/monitor selection, added more definition to operation. Revision D - updated DIA-01/X to CE version, added commands to enable/disable camera ID display and Sector ID title. Revision E - discontinued camera power option Issue 2 - November 1996 reformatted Issue 2, Rev. A October 1999 updated installation drawings , , , , BY ULTRAK, INC. ALL RIGHTS RESERVED PRINTED IN THE UNITED STATES OF AMERICA ULTRAK, INCORPORATED P.O. BOX 200 LANCASTER, OHIO (740) ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MEANS WITHOUT WRITTEN PERMISSION FROM ULTRAK, INCORPORATED. THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL RESPECTS. HOWEVER, ULTRAK, INCORPORATED CANNOT ASSUME RESPONSIBILITY FOR ANY CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION CONTAINED HEREIN IS SUBJECT TO CHANGE. REVISIONS TO THIS PUBLICATION OR NEW EDITIONS OF IT MAY BE ISSUED TO INCORPORATE SUCH CHANGES.

3 IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5. Cleaning - Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. See cleaning procedures under Maintenance. 6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Water and Moisture - Do not use this unit near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, near a swimming pool, in an unprotected outdoor installation, or any area which is classified as a wet location. 8. Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit may fall, causing serious injury to a person and serious damage to the unit. Use only with a stand, tripod, bracket, or mount recommended by the manufacturer, or sold with the product. Any mounting of the unit should follow the manufacturer s instructions, and should use a mounting accessory recommended by the manufacturer. A cart should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the cart to overturn. 9. Ventilation - Openings in the enclosure, if any, are provided for ventilation and to ensure reliable operation of the unit and to protect it from overheating. These openings must not be blocked or covered. This unit should not be placed in a built-in installation unless proper ventilation is provided or the manufacturer s instructions have been adhered to. 10. Power Sources - This unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply you plan to use consult your dealer or local power company. For units intended to operate from battery power, or other sources, refer to the operating instructions. 11. Grounding or Polarization - This unit may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Alternately, this unit may be equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 12. Power-Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the equipment.

4 13. Power Lines - An outdoor system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outdoor system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. U.S.A. models only - refer to the National Electrical Code Article 820 regarding installation of CATV systems. 14. Overloading - Do not overload outlets and extension cords as this can result in a risk of fire or electric shock. 15. Object and Liquid Entry - Never push objects of any kind into this unit through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the unit. 16. Servicing - Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 17. Damage Requiring Service - Unplug the unit from the outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation. e. If the unit has been dropped or the cabinet has been damaged. f. When the unit exhibits a distinct change in performance - this indicates a need for service. 18. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 19. Safety Check - Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition. 20. Coax Grounding - If an outside cable system is connected to the unit, be sure the cable system is grounded. U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No , provides information with respect to proper grounding of the mount and supporting structure, grounding of the coax to a discharge unit, size of grounding conductors, location of discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. 21. Lightning - For added protection of this unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the unit due to lightning and power-line surges.

5 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK, DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This label may appear on the bottom of the unit due to space limitations. The lightning flash with an arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance (servicing) instructions in the literature accompanying the equipment Vac, 50 Hz power cords, input and output, must comply with the latest versions of IEC Publication 227 or IEC Publication 245. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

6 HANDLING ELECTROSTATIC-SENSITIVE DEVICES ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES WARNING ELECTROSTATIC SENSITIVE DEVICE. USE PROPER CMOS/MOSFET HANDLING PRECAUTIONS TO AVOID ELECTROSTATIC DISCHARGE. NOTE: Grounded wrist straps must be worn and proper ESD safety precautions observed when handling the electrostatic-sensitive printed circuit boards.

7 TABLE OF CONTENTS Page SECTION 1. INTRODUCTON GENERAL SECTION 2. INSTALLATION AND INTERCONNECTIONS GENERAL HANDLING PROCEDURES INTERCONNECTING CABLING REQUIREMENTS INSTALLATION DRAWINGS SECTION 3. OPERATION GENERAL CONTROLS AND INDICATORS OPERATION Selecting the Control Camera and Control Monitor Video Switching JAD-832 Control Commands MONITOR SEQUENCES IN THE CATS VIDEO SWITCHER Programming Monitor Sequences Starting/Stopping Monitor Sequences SYSTEM SECURITY SECTION 4. MAINTENANCE PREVENTIVE MAINTENANCE TROUBLESHOOTING i

8 LIST OF FIGURES Page Figure 3-1. JAD-832 JOYSTICK CONTROLLER CONTROLS AND INDICATORS LIST OF DRAWINGS JAD-832 Joystick Control Unit Installation (D/N ) DIA-01 Control Interface Adapter Installation (D/N ) DIA-01/X (CE) Control Interface Adapter Installation (D/N ) Hand Control Interface Panel Installation (D/N ) Hand Controller Interface Panel Schematic (D/N ) COE-08A Active Output Expander Unit (D/N ) MUX-05 Multiplexer Installation (D/N ) LIST OF TABLES Table 3-1. CONTROL COMMANDS ii

9 SECTION 1. INTRODUCTON 1.1 GENERAL The JAD-832 Joystick Controller Unit consists of a joystick, switches, and keypad interface to provide remote control of the camera, lens, and pan/tilt functions for a FastScan /SmartScan system. The JAD-832 Joystick Controller can be used to control and program a CATS Series Video Switcher. This controller interfaces to various equipment types to enhance the capabilities of the FastScan/SmartScan system. These equipment types are the DIA-01 Control Interface Adapter, Hand Controller Interface Panel, MUX-05 Multiplexer, CATS Series Video Switchers, and COE-08A/16A Active Output Expander Unit. All of these units provide the communications interface for the JAD-832 Controller to control a FastScan/SmartScan system. Up to five JAD-832 Joystick Controllers can control a system simultaneously if a MUX-05 Multiplexer is installed. The MUX-05 Multiplexer receives all commands entered by operators at the JAD-832 Controllers. If control of the same camera is requested by more than one operator, the MUX-05 gives control of the camera to the operator requesting control last. If a CATS Video Switcher is also installed, the operators can simultaneously control the switcher. 1-1

10

11 SECTION 2. INSTALLATION AND INTERCONNECTIONS 2.1 GENERAL This section describes the handling procedures, interconnecting cabling requirements, and the installation set-up procedures for the JAD-832 Joystick Controller Unit. 2.2 HANDLING PROCEDURES Each container shipped by Diamond Electronics is labeled with the customer order number, the Diamond Electronics order number, and the items contained therein. In addition, each container has a carton number and the total number of cartons shipped in any given lot. On receipt and during unpacking, each item must be compared to the shipping documents accompanying each shipment to ensure that all items have been received. Notification must be supplied to Diamond Electronics and the delivering carrier immediately if any discrepancies have occurred. Most Diamond Electronics equipment is packaged with the protection of "foamedin-place" polyurethane dunnage. This packing medium provides a reusable container for any subsequent reshipment. The polyurethane molds itself around each object to provide an upper and lower enclosure. Care should be taken in unpacking to ensure that the wooden crating or the corrugated fiberboard container is not damaged. Only the strapping or the tape needed to open the top of a container should be cut. Staples may also be used in some containers. Care should be taken to avoid puncturing any container with unpacking tools such as nail pullers, knives, or shears. Each container and its plastic-covered polyurethane enclosures should be stored for reuse in the event that reshipment of any item becomes necessary. 2-1

12 No item should be removed from its shipping container for any prolonged period of time until it is ready for permanent installation. All handling of equipment outside of its protective packaging must be performed with utmost care. Any installation of equipment not accomplished by Diamond Electronics personnel must be accomplished in strict accordance with these procedures so as not to void any warranty provisions. 2.3 INTERCONNECTING CABLING REQUIREMENTS A coiled cable assembly (P/N ) is provided with the JAD-832 Joystick Controller Unit for connection to the various equipment types. CAUTION Do not use commercially available telephone-type cable to connect the Joystick Controller to any interface equipment or improper operation will result. Use only the lower impedance cable supplied with the unit to make connections. The JAD-832 Controller requires +5Vdc to operate. The DIA-01 Control Interface provides the +5Vdc required. If the JAD-832 Controller is plugged into the front panel controller connector on the CATS Video Switcher or the MUX-05 Multiplexer, a DIA-01 Control Interface is not required. If the JAD-832 Controller is connected to the rear panel COMM connector of the CATS Video Switcher or any of the rear panel DIN connectors on the MUX-05 Multiplexer, a DIA-01 Control Interface is required to power the JAD-832 Controller. 2-2

13 2.4 INSTALLATION DRAWINGS The following drawings may be used as a reference before performing a systemlevel installation. Title Page JAD-832 Joystick Control Unit Installation (D/N ) DIA-01 Control Interface Adapter Installation (D/N ) DIA-01/X (CE) Control Interface Adapter Installation (D/N ) Hand Control Interface Panel Installation (D/N ) Hand Controller Interface Panel Schematic (D/N ) COE-08A Active Output Expander Unit (D/N ) MUX-05 Multiplexer Installation (D/N )

14 2-4

15 2-5

16 2-6

17 2-7

18 2-8

19 2-9

20 2-10

21 SECTION 3. OPERATION 3.1 GENERAL This section contains information on the controls and indicators and the operation of the JAD-832 Joystick Controller. The procedures for programming monitor sequences in the CATS Video Switcher are also in this section. 3.2 CONTROLS AND INDICATORS Figure 3-1 shows the controls and indicators. A description of each follows the illustration. Figure 3-1. JAD-832 JOYSTICK CONTROLLER CONTROLS AND INDICATORS 3-1

22 1. JOYSTICK CONTROL Movement of the joystick up and down provides the tilting of the pan and tilt unit; movement of the joystick left and right provides the scanning (pan) of the pan and tilt unit; movement of the joystick at an angle provides both panning and tilting; and turning the joystick knob clockwise/counterclockwise provides the zoom functions. The joystick control is rate proportional; the farther the joystick is moved, the faster the function is performed. 2. FOCUS SWITCH This switch, when pushed up, provides far focusing; when pushed down, it provides near focusing. 3. IRIS SWITCH This switch is only functional when the MIO-100 Auto/Manual Iris option is installed in the FastScan or SmartScan assembly. Upon power-up of the system, this switch is disabled. The iris function is set to automatic. To enable the switch, you must select manual iris (FUN>9>ENT). Once enabled, pushing the switch up, opens the camera lens iris; pushing the switch down, closes the camera lens iris. 3-2

23 4. SLIDE SWITCHES CAUTION These switches are for Diamond Electronics internal use only. They are not intended for customer use. Operation of these switches will release the spring return action of the joystick causing continuous panning and/or tilting action and will void all warranties. The vertical switch, when pushed up, releases the spring return action of the joystick operation controlling the panning. The horizontal switch, when pushed to the left, releases the spring return action of the joystick operation controlling the tilting. 5. DISPLAY The display shows the camera number the controller is currently controlling and the monitor number the camera is called to. The display also shows each keystroke as it is entered. Any input errors may be corrected by pressing the CLR key and reprogramming. The display blinks at various data entry points to indicate more data is required to complete a command. 3-3

24 6. KEYPAD The keypad is used to perform the following functions for the FastScan and SmartScan assemblies. - Initialize (reset) the JAD-832 Controller - Enable/disable data transmission to FastScan/SmartScan Domes - Control camera and monitor selection - Automatic/manual iris control (optional) - Video switching - Program Monitor Sequencing (if Video Switcher is installed) - Auxiliary Control (RCO-4 CATS Video Switcher Relay Option or Addressable Contact Output Device) The following functions apply to SmartScan units only: - Manual Control - Find Home - PreShot Callup - PreShot Listing - Run VectorScan - VectorScan Listing - Enable/Disable Camera ID Display - Enable/Disable coordinate and error log displays Note: A SmartScan unit cannot be programmed using a JAD-832 Controller. A JPD Series Controller and a KBD-100 Keyboard are required for programming SmartScan units. 3-4

25 3.3 OPERATION Operation can begin when power is applied to all components in the system. Upon power-up, the JAD-832 Controller displays the control camera and the control monitor. Camera one is the control camera and monitor one is the control monitor. All operator control data (pan, tilt, zoom, focus, iris, PreShots, VectorScans, etc.) is sent to camera address one Selecting the Control Camera and Control Monitor The control camera and monitor can be changed. A video switcher is required to switch cameras to monitors. There are two commands to change the camera and monitor combination currently controlled by the JAD-832 Controller. The commands are in bold typeface. Each keystroke is separated by the greater than symbol (>). a. Change Control Camera To change the control camera (but not the control monitor), enter the following command sequence. Camera #> ENT 3-5

26 The selected camera is switched to the displayed control monitor. The operator has manual control of the selected camera. In a system with multiple controllers, the controller to request control of a camera last, gets control. For example, the user wants to control camera 5 instead of the one currently controlled. 5> ENT b. Change the Control Monitor and Control Camera To change the control monitor and the control camera, enter the following command sequence. 0> Monitor #> ENT> Camera #> ENT For example, the user wants camera 3 to be the new control camera, and wants monitor 2 to be the new control monitor. 0> 2> ENT> 3> ENT 3-6

27 3.3.2 Video Switching Cameras can be switched to monitors without changing the control camera and control monitor. Perform the following command sequence to perform video switching only. CALL> Monitor #> ENT> Camera #> ENT For example, the user wants to switch camera 5 to monitor 3. CALL> 3> ENT> 5> ENT JAD-832 Control Commands The commands to control the operation of the JAD-832 Controller and the FastScan/SmartScan units are performed using the FUN key. When a command function is started, but not completed within five seconds, the controller times-out and automatically cancels the command. Table 3-1 defines the control commands. The commands are in bold typeface and the keystrokes are separated by the greater than symbol (>). 3-7

28 COMMAND FUN> 0> ENT FUN> 1> ENT FUN> 2> ENT FUN > 8> ENT> Auxiliary #> ENT TABLE 3-1. CONTROL COMMANDS DESCRIPTION INITIALIZE JAD-832. This command initializes the JAD-832 Controller; the unit is now the same as if power-up had just occurred. DISABLE JAD DATA TRANSMISSION. This command disables the data transmission to all FastScan/ SmartScan units. You can still send switching commands to the CATS Video Switcher. ENABLE JAD DATA TRANSMISSION. This command enables the data transmission to all FastScan/ SmartScan units. CATS VIDEO SWITCHER AUXILIARY CONTROL. This command is for controlling the four contact outputs on the CATS Video Switcher RCO-4 Option. This command toggles the status of the relay between on and off. When the contact output numbers are displayed on the controller; a steady number indicates the relay is on; a flashing number indicates the relay is off. If contact output # 1 is selected, the display appears with the number 1 steady and outputs 2 through 4 flashing. If contact output 3 is selected, the display appears with the number 3 steady and outputs 1, 2, and 4 flashing. 3-8

29 COMMAND FUN> 9> ENT FUN> 10> ENT FUN> 12> ENT> Contact Output #> ENT (ON) FUN> 12> ENT> Contact Output #> CLR (OFF) TABLE 3-1. CONTROL COMMANDS DESCRIPTION IRIS CONTROL MODE. The MIO-100 manual iris override option must be installed in the FastScan or SmartScan assembly to be able to select the iris mode. Upon power-up of the unit, the iris control is set to automatic. Entering this command the first time switches to manual iris control. Entering the command again switches back to automatic iris control. When in the manual iris mode for a selected camera, the selection of a different control camera automatically returns the originally selected camera to automatic iris control. CANCEL COMMAND. This command cancels the current FUN key operation. This command is used when the operator is in the middle of a command, decides not to perform the command, and doesn t want to wait for the 5-second timeout to cancel the command. AUXILIARY CONTROL FOR CONTROL CAMERA ADDRESS (CONTACT OUTPUT DEVICE OR CRX CONTROL RECEIVER). This command energizes the contact output # selected on the contact output device with the address of the selected control camera. AUXILIARY CONTROL FOR CONTROL CAMERA ADDRESS (CONTACT OUTPUT DEVICE OR CRX CONTROL RECEIVER. This command de-energizes the contact output # selected on the contact output device with the address of the selected control camera. 3-9

30 TABLE 3-1. CONTROL COMMANDS COMMAND DESCRIPTION SMARTSCAN CONTROL FUN> SEQ> 1> ENT MANUAL CONTROL. This command returns a SmartScan unit to manual control. If the camera s last position happens to be in a programmed sector, the manual control message appears briefly before displaying the sector name. FUN> SEQ> 2> ENT HOME. This command sends the control camera (must be a SmartScan unit) to its home position. This is used to initialize the processor board upon power-up of the system. The control monitor displays FINDING HOME. FUN> CAL> 1> ENT> GO TO PRESHOT. This command sends the control PreShot #> ENT camera to the selected PreShot position. The PreShot title appears on the control monitor. Note: The PreShots must be programmed using a JPD Series Controller and a KBD-100 Keyboard. After PreShots are stored in the SmartScan unit, the JAD-832 Controller can be used to send the SmartScan unit to the programmed PreShots. FUN> CAL> 2> ENT> RUN VECTORSCAN ONCE. This command runs the VectorScan #> ENT selected VectorScan stored in the control camera one time, then returns the SmartScan unit to manual control. The control monitor displays the PreShot title as the SmartScan is directed to that PreShot. At the end of the VectorScan, the MANUAL CONTROL message is displayed. 3-10

31 TABLE 3-1. CONTROL COMMANDS COMMAND DESCRIPTION FUN> CAL> 3> ENT> RUN VECTORSCAN CONTINUOUSLY. This VectorScan #> ENT command runs the VectorScan in the control camera continuously until an operator takes manual control of the SmartScan unit. To take manual control, move the joystick in any direction or enter the FUN>SEQ>1>ENT (manual control) command using the keypad. FUN> PGM> 1> ENT> LIST PROGRAMMED VECTORSCANS. This command displays the VectorScans stored in the control camera. The VectorScan names and numbers are displayed on the control monitor. A page of six names is displayed. Each time you press the ENT key, the next six names are displayed. When the END of DIRECTORY message is displayed, you are at the end of the list. To view the first page again, press ENT. When finished viewing the list, press the CLR key. While the list is displayed, the word LIST is flashing on the JAD-832 Controller display. FUN> PGM> 3> ENT LIST PROGRAMMED PRESHOTS. This command lists the PreShots stored in the SmartScan (control camera). The PreShot number and title is displayed. A page of six names is displayed at a time. Press the ENT key to view more PreShots. When the message END of DIRECTORY is displayed, you are at the end of the list. To return to the first page, press the ENT key. When finished viewing the list, press the CLR key. While the list is displayed, the word LIST is flashing on the JAD-832 Controller display. 3-11

32 TABLE 3-1. CONTROL COMMANDS COMMAND DESCRIPTION FUN> FUN> 1> ENT ENABLE CAMERA # DISPLAY AND SECTOR ID TITLE DISPLAY. FUN> FUN> 2> ENT DISABLE CAMERA # DISPLAY AND SECTOR ID TITLE DISPLAY. FUN> FUN> 3> ENT ENABLE COORDINATE AND ERROR LOG DISPLAY. This command toggles between the coordinate and error log displays. First entry of this command turns on the coordinate display. It appears above the CAM ID # on the control monitor. Azimuth and Elevation positions are shown. If a SmartScan unit, the zoom and focus settings are shown. Second entry of this command turns on the error log display. The error log shows the last 64 detected errors. When the error log is displayed an E appears on the camera number line of the display. FUN> FUN> 4> ENT TURN OFF COORDINATE AND ERROR LOG DISPLAYS. 3.4 MONITOR SEQUENCES IN THE CATS VIDEO SWITCHER Programming Monitor Sequences One monitor sequence can be programmed for each video output on the CATS Video Switcher. The sequence is stored on the printed circuit board on the CATS Video Switcher. 3-12

33 Up to 32 cameras with programmable dwell times of 0-30 seconds between each camera can be programmed for each sequence. Use the following command sequence to program a monitor sequence. NOTE A sequence cannot be programmed for the control monitor displayed on the JAD-832 unless data transmission to the FastScan/SmartScan assemblies is disabled. Use the FUN> 1> ENT command sequence to disable data transmission. PGM> Monitor #> ENT> Camera #> ENT>Dwell Time (0-30 seconds)> ENT> Camera # > ENT> Dwell Time> ENT>...Camera #> ENT> Dwell Time> ENT> PGM Pressing the PGM key at the end of the command sequence stores the sequence and exits the user from the programming mode Starting/Stopping Monitor Sequences Monitor sequences stored in a CATS Video Switcher can be started and stopped using the JAD-832 Controller. Use the following command sequence to start or stop a monitor sequence. The command is in bold typeface. The keystrokes are separated by the greater than symbol (>). SEQ> Monitor #> ENT 3-13

34 For example, the user wants to start the sequence programmed for monitor 2. SEQ> 2> ENT The JAD-832 Controller sends the command to the CATS Video Switcher to perform the sequence programmed for monitor 2. The sequence continues to run until stopped by an operator. Use the same command to stop the sequence (SEQ>Monitor #> ENT). For example, the user wants to stop the sequence running on monitor 2. SEQ> 2> ENT 3.5 SYSTEM SECURITY The JAD-832 Joystick Controller(s) may be disconnected from the system without changing or deleting any sequences stored in the CATS Video Switcher or PreShots, VectorScans, or Sector ID s in the SmartScan units. When the controller is disconnected the camera positions cannot be changed. 3-14

35 SECTION 4. MAINTENANCE 4.1 PREVENTIVE MAINTENANCE Use of preventive maintenance allows detection and correction of minor faults before they become serious enough to cause equipment failure. Every 3 months, perform the following. 1. Inspect all interface connecting cabling for deterioration or other damage. 2. Clean the cover with a soft cloth using any mild commercial cleaner. 4.2 TROUBLESHOOTING If problems occur at the initial installation phase, verify the unit is plugged in properly with the correct low-impedance cable supplied with the unit. Because this unit is one part of an overall system, it may be necessary to verify that the other equipment types have been installed and are operating correctly before assuming the problem exists at the JAD-832 Joystick Controller. 4-1

36 If problems still exist after verifying correct installation and the problem has been isolated to the Joystick Controller, then it must be removed for servicing. THERE ARE NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. Any equipment returned to Diamond Electronics for warranty or service repair must have a prior written Authorization to Return Material (ARM) form completed for its repair. Contact: Diamond Electronics, Inc. Service Department 4465 Coonpath Road Carroll, Ohio (614) Toll Free USA:

37 APPENDIX A. QUICK REFERENCE GUIDE JAD-832 CONTROL FUNCTION Initialize JAD-832 (same as power-up) Disable JAD-832 Data Transmission Enable JAD-832 Data Transmission PROCEDURE (Keystrokes are separated by >s FUN>O>ENT FUN>1>ENT FUN>2>ENT FASTSCAN/SMARTSCAN MANUAL CONTROL FUNCTION Select Control Camera Select Control Monitor and Control Camera Call Camera to Monitor (video switching - doesnt change control) Turn camera power on (not available on current products) Turn camera power off (not available on current products) Manual Iris Control (requires MIO-100 option) Cancel Command PROCEDURE (Keystrokes are separated by >s Camera #>ENT 0>Monitor #>Camera #> ENT CALL>Monitor #> ENT> Camera #> ENT FUN>3>ENT FUN>4>ENT FUN>9>ENT FUN>10>ENT A-1

38 SMARTSCAN CONTROL FUNCTION Manual Control Find Home Go to PreShot Run VectorScan Once Run VectorScan Continuously List VectorScans List PreShots Enable Camera # and Sector Title Display Disable Camera # and Sector Title Display Turn on Coordinate Display Turn on Error Log Display Turn off Error Log or Coordinate Display PROCEDURE FUN>SEQ>1>ENT FUN>SEQ>2>ENT FUN>CAL>1>ENT>PreShot #>ENT FUN>CAL>2>ENT>VectorScan #>ENT FUN>CAL>3>ENT>VectorScan #>ENT FUN>PGM>1>ENT> Press ENT to view next page(s) Press CLR to return to manual control FUN>PGM>3>ENT Press ENT to view next page(s) Press CLR to return to manual control FUN>FUN>1>ENT FUN>FUN>2>ENT FUN>FUN>3>ENT FUN>FUN>3>ENT>FUN>FUN>3>ENT FUN>FUN>4>ENT VIDEO SWITCHER SEQUENCES FUNCTION Program Monitor Sequences stored in CATS Video Switcher Start/Stop Monitor Sequences Auxiliary Control (Switcher only) PROCEDURE PGM> Monitor #> ENT> Camera #> ENT>Dwell time> ENT> Camera #> ENT> Dwell time> ENT... camera #> ENT> Dwell Time>PGM SEQ>Monitor #> ENT Starts the sequence if it is not running; stops the sequence if it is running. FUN>8>ENT>Auxiliary #>ENT A-2

39 AUXILIARY CONTROL (CRX-800 Series, CRX-500 Series, AIF-100/CO) FUNCTION Turn Relay On Turn Relay Off PROCEDURE FUN>12>ENT> Auxiliary #> ENT FUN>12>ENT>Auxiliary #> CLR A-3