TECHNICAL MANUAL. Intel H81 Express Chipset. Based Mini-ITX M/B

Transcription

1 TECHNICAL MANUAL Of Intel H81 Express Chipset Based Mini-ITX M/B NO. SYS86355VGGA Revision: 1.0 Release date: July 28, 2015 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

2 Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding. To minimize pollution and ensure environment protection of mother earth, please recycle. i

3 TABLE OF CONTENT ENVIRONMENTAL SAFETY INSTRUCTION... iii USER S NOTICE... iv MANUAL REVISION INFORMATION... iv ITEM CHECKLIST...iv CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD 1-1 FEATURE OF MOTHERBOARD SPECIFICATION LAYOUT DIAGRAM...3 CHAPTER 2 HARDWARE INSTALLATION 2-1 JUMPER SETTING CONNECTORS AND HEADERS CONNECTORS HEADERS CHAPTER 3 INTRODUCING BIOS 3-1 ENTERING SETUP BIOS MENU SCREEN FUNCTION KEYS GETTING HELP MENU BARS MAIN MENU ADVANCED MENU CHIPSET MENU BOOT MENU SECURITY MENU TURBOOC MENU SAVE & EXIT MENU...43 ii

4 Environmental Safety Instruction Avoid the dusty, humidity and temperature extremes. Do not place the product in any area where it may become wet. 0 to 60 centigrade is the suitable temperature. (The figure comes from the request of the main chipset) Generally speaking, dramatic changes in temperature may lead to contact malfunction and crackles due to constant thermal expansion and contraction from the welding spots that connect components and PCB. Computer should go through an adaptive phase before it boots when it is moved from a cold environment to a warmer one to avoid condensation phenomenon. These water drops attached on PCB or the surface of the components can bring about phenomena as minor as computer instability resulted from corrosion and oxidation from components and PCB or as major as short circuit that can burn the components. Suggest starting the computer until the temperature goes up. The increasing temperature of the capacitor may decrease the life of computer. Using the close case may decrease the life of other device because the higher temperature in the inner of the case. Attention to the heat sink when you over-clocking. The higher temperature may decrease the life of the device and burned the capacitor. iii

5 USER S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE DO ASSURE THIS MANUAL MEETS USER S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE). PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER S BENEFIT, WITHOUT INTENT TO INFRINGE. Manual Revision Information Reversion Revision History Date 1.0 First Edition July 28, 2015 Item Checklist R Motherboard R DVD for motherboard utilities R User s Manual R Cable(s) R I/O Back panel shield iv

6 Chapter 1 Introduction of the Motherboard 1-1 Feature of Motherboard Intel H81 express chipset Support LGA 1150 CPU socket Intel Core i7 processors / Intel Core i5 processors / Intel Core i3 processors / Intel Celeron processors Support DDRIII 1066/1333/1600 MHz SO-DIMM up to 8GB Integrated with dual Realtek RTL8111G Gigabit Ethernet LAN chips Integrated with RealTek ALC887-GR HD Audio Codec Support USB 3.0 data transport demands. Support 2 * Serial ATAIII (6Gb/s) Devices Support 1*PCIE 2.0 x16 by 16 Lane slot and 1*full-size Mini PCI-E slot Support 1*full-size msata slot Support CPU Smart FAN Supports ACPI S3 Function Compliance with ErP Standard Support Watchdog Timer Technology 1

7 1-2 Specification Spec Design Chipset CPU Socket Memory Slot Expansion Slot Storage Gigabit LAN Chip Audio Chip BIOS Multi I/O 2 Description Mini-ITX form factor 6 layers ; PCB size: 17.0x17.0cm Intel H81 Express Chipset Support Intel LGA 1150 Socket Core i7 Processor, Intel Core i5 Processor, Intel Core i3 Processor, Intel Celeron processors * for detailed CPU support information please visit our website 1* DDRIII SO-DIMM slot to support DDRIII 1066/1333/1600 MHz SO-DIMM, expandable to 8GB 1*PCIE 2.0 x16 by 16 lane slot 1*Full-size Mini-PCIE slot(minipcie) 1*Full-size Mini-PCIE/MSATA selectable slot(mini_card) 1* SIM Card Slot 2* SATA III 6G/s Connector 1*Full-size Mini-PCIE/MSATA selectable slot t(mini_card) Integrated with 2* Realtek RTL8111G PCI-E Gigabit LAN chips Support Fast Ethernet LAN function of providing 10/100/1000 Mbps Ethernet data transfer rate Realtek ALC887-GR 6-channel HD Audio Codec integrated Audio driver and utility included 32MBit Flash ROM Rear Panel I/O: 1*PS/2 keyboard & mouse combo connector 2* VGA port connector 1* HDMI port connector 1* RS232/422/485 serial port (COM1) 4*USB 3.0 port connector 2*USB 2.0 port connector

8 1-3 Layout Diagram Rear IO Diagram 2*RJ-45 LAN connector 1*3-jack audio connector (Line-in, Line-out, MIC) Internal I/O Connectors& Headers: 1 *24-pin main power connector 1 *4-pin 12V Power connector 1*Front panel audio header 1*HDMI_SPDIF header 1*LAN activity LED header 2 * 9-Pin USB 2.0/1.1 header for 4* USB 2.0/1.1 ports 1*Front panel header 1* RS232/422/485 serial port header (COM2) 2* RS232 serial port expansion block (F1_5COM/F2_5COM) 1*GPIO header 1*CPU fan header & 1*System fan header PS/2 Keyboard & Mouse Port COM1 Serial Port VGA Port RJ-45 LAN Ports Line-IN Line-OUT MIC-IN USB 2.0 Ports VGA Port HDMI Port USB 3.0 Ports 3

9 Motherboard Internal Diagram Front USB 2.0 Headers SYSFAN1 Header Serial Port Expansion Blocks (F2_5COM/F1_5COM) Intel H81 Chipset SATAIII Ports Full-size Mini-PCIE Slot (MINI_PCIE) Full-size Mini-PCIE/ MSATA Slot (MINI_CARD) CPUFAN Header Front Panel Header Serial Port Header (COM2) GPIO Header Main Power Connector *Rear IO (Please refer to Page3) ATX12V Power Connector Intel LGA1150 CPU Socket DDRIII SODIMM Slot LANLED Header Front Panel Audio Header HDMI_SPDIF Header PCI Express 2.0 x16 by 16 Lane slot 4

10 Motherboard Internal Diagram--Back SIM Card Slot 5

11 Motherboard Jumper Position JP5 AT_ATX_MODE JBAT JP3 JP4 CASE_OPEN JPCOM2 JP6 JPCOM1 6

12 Jumper Jumper Name Description JBAT CMOS RAM Clear Function Setting 3-pin Block AT_ATX_MODE ATX/AT Mode Select 3-pin Block CASE_OPEN Case Open Message Display Function 2-pin Block JPCOM1 COM1 Port Pin9 Function Select 4-pin Block JPCOM2 COM2 Port Pin9 Function Select 4-pin Block JP3&JP4 &JP5&JP6 MINI_CARD Slot Mini-PCIE/MSATA Function Select 3-pin Block Connectors Connector Name ATXPWR ATX Power Connector ATX12V ATX 12V Power Connector SATA1/SATA2 SATAIII Connector X2 USB_PS2 (Top) PS/2 Keyboard & Mouse Combo Port Connector USB_PS2(Middle & Bottom) USB 2.0 Port X2 CRT1_COM1(Top) COM1 RS232/422/485 Serial Port Connector CRT1_COM1 (Bottom) VGA Port Connector VGA2 VGA Port Connector HDMI HDMI Port Connector UL1(Top)/UL2(Top) RJ-45 LAN Connector X2 UL1(Middle & Bottom) USB 2.0 Port Connector X4 /UL2(Middle & Bottom) AUDIO Line In/ Line Out /MIC Audio Connector 7

13 Headers Header Name Description FP_AUDIO Front Panel Audio Header 9-pin Block LAN_LED LAN Activity LED Header 8-pin Block HDMI_SPDIF HDMI_SPDIF Out Header 2-pin Block F_USB1/F_USB2 USB Header 9- pin Block JW_FP Front Panel Header(PWR LED/ HD 9-pin Block LED/ Power Button /Reset) COM2 RS232/422/485 Serial Port Header 9-pin Block F1_5COM(COM3-COM7) RS232 Serial Port Header 45-pin Block /F2_5COM(COM8-COM12) Expansion Block GPIO_CON GPIO Header 10-pin Block SYSFAN1 System Fan Header 3-pin Block CPUFAN CPU Fan Header 4-pin Block 8

14 Chapter 2 Hardware Installation 2-1 Jumper Setting JBAT (3-pin): Clear CMOS Function Setting JBAT 1 AT_MODE (3-pin): ATX Mode/AT Mode Select Closed: Normal; Closed:Clear CMOS. AT_ATX_MODE Closed: ATX Mode Selected; Closed: AT Mode Selected. 9

15 *ATX Mode Selected: Press power button to power on after power input ready; AT Mode Selected: Directly power on as power input ready. CASE_OPEN (2-pin): Case Open Message Display Function Select CASE_OPEN Open: Normal(Defualt); Closed: Case Open Function Selected(One Touch). Pin 1-2 Closed: When Case open function pin short to GND, the Case open function was detected. When Used, needs to enter BIOS and enable Case Open Detect function. In this case if your case is removed, next time when you restart your computer, a message will be displayed on screen to inform you of this. JPCOM1 (4-pin): COM1 Port Pin9 Function Select JPCOM1 COM1 Port Pin Closed: Pin9=RI; Closed: Pin9=+5V; Closed: Pin9=+12V. 10

16 JPCOM2 (4-pin): COM2 Port Pin9 Function Select JPCOM2 COM2 Header Pin Closed: Pin9=RI; Closed: Pin9=+5V; Closed: Pin9=+12V. JP3&JP4&JP5&JP6 (3-pin): MINI_CARD Slot Mini-PCIE/MSATA Function Select JP3&4&5&6 MINI_CARD Function Select JP JP6 JP3 JP4 1-2 Closed: MINI_CARD functions as MSATA interface. JP5 JP JP3 JP4 2-3 Closed: MINI_CARD functions as Mini-PCIE Slot. 11

17 2-2 Connectors and Headers Connectors (1) Rear Panel Connectors PS/2 Keyboard & Mouse Port COM1 Serial Port VGA Port RJ-45 LAN Ports Line-IN Line-OUT MIC-IN USB 2.0 Ports VGA Port HDMI Port USB 2.0 Ports Icon Name Function PS/2 Keyboard & Mouse Combo Port USB 2.0 Port For user to connect PS/2 keyboard or PS/2 mouse device to the board. To connect USB keyboard, mouse or other devices compatible with USB specification. *COM1: RS232/422/485 Serial Port VGA HDMI Port Mainly for user to connect external MODEM or other devices that supports Serial Communications Interface. To connect display device that support VGA specification. To connect display device that support HDMI specification. 12

18 USB 3.0 Port RJ-45 LAN Port 3-jack Audio Connector To connect USB keyboard, mouse or other devices compatible with USB specification. USB 3.0 ports supports up to 5Gbps data transfer rate. This connector is standard RJ-45 LAN jack for Network connection. BLUE : Line-in Connector GREEN:Line-out Connector PINK : MIC Connector (2) COM1 (9-pin Block): RS232/422/485 Port COM1 port can function as RS232/422/485 port. In normal settings COM1 functions as RS232 port. With compatible COM cable COM1 can function as RS422 or RS 485 port. User also needs to go to BIOS to set Transmission Mode Select for COM1 (refer to Page 29~30) at first, before using specialized cable to connect different pins of this port. RS485 D+(A) RS485 D-(B) RS422RX-(B) RS422RX+(A) (B) RS422TX+(A) RS422TX-(B) For RS422 Mode For RS485 Mode 13

19 (3) ATXPWR (24-pin block): Power Connector Row1 Row2 Pin12 Pin1 PIN ROW1 ROW V +3.3V V -12V 3 GND GND 4 +5V Soft Power on 5 GND GND 6 +5V GND 7 GND GND 8 Power OK -5V 9 +5V Stand by +5V V +5V V +5V V GND (4) ATX12V (4-pin block): ATX12V Type Power Connector Pin1 Pin No. Definition 1 GND 2 GND 3 +12V 4 +12V 14

20 (5) SATA1/SATA2(7-pin block): SATAIII Port connector These connectors are high-speed SATAIII ports that support 6Gbps transfer rate Headers Pin No. Defnition 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND (1) FP_AUDIO (9-pin): Line-Out, MIC-In Header This header connects to Front Panel Line-out, MIC-In connector with cable. MIC2-L MIC2-R LINE OUT-R SENSE LINE OUT-L 2 Pin1 15 LINE_OUT_JD DETECT MIC_JD GND Line-Out, MIC Header

21 (2) LAN_LED (8-pin): LAN Activity LED Header LAN1_VCC LAN1_100M LAN2_VCC LAN2_100M Pin1 LAN1_ACT LAN1_1G LAN2_ACT LAN2_1G (3) HDMI_SPDIF (2-pin): HDMI-SPDIF Out Header SPDIF GND Pin1 16

22 (4) F_USB1/F_USB2 (9-pin): USB Port Headers Pin 1 VCC -DATA +DATA GND VCC -DATA +DATA GND NC (5) JW-FP (9-pin): Front Panel Header Pin 1 HDDLED+ HDDLED- GND RSTSW VCC PWRLED+ PWRLED- PWRBTN GND 17

23 (6) COM2 (9-Pin): RS232/422/485 Serial Port Header Pin Pin NO. RS232 *RS422 *RS485 Pin 1 DCD TX- DATA- Pin 2 RXD TX+ DATA+ Pin 3 TXD RX+ NC Pin 4 DTR RX- NC Pin 5 GND GND GND Pin 6 DSR NC NC Pin 7 RTS NC NC Pin 8 CTS NC NC Pin 9 RI NC NC *Notice: COM2 header supports RS232/RS422/RS485 function, with compatible COM cable for RS232, RS422 or RS 485 function. User also needs to go to BIOS to set Transmission Mode Select for COM2 (refer to Page 29~30). 18

24 (7) F1_5COM/F2_5COM (45-Pin): RS232 Serial Port Header Expansion Block F1_5COM & F2_5COM are RS232 serial port header expansion blocks each composed of 5* RS232 serial port headers (F1_5COM by COM3/4/5/6/7; F2_5COM by COM8/9/10/11/12/13). Pin 1 Pin COM8 COM3 COM9 COM4 COM10 COM5 COM11 COM6 COM12 COM7 F2_5COM F1_5COM 19

25 F1_5COM COM3 COM4 COM5 COM6 COM7 Pin RS232 Pin RS232 NO. NO. Pin 1 DCD3 Pin 2 DSR3 Pin3 SIN3 Pin 4 RTS3 Pin 5 SOUT3 Pin 6 CTS3 Pin 7 DTR3 Pin 8 RI3 Pin 9 GND Pin 10 N/A Pin 11 DCD4 Pin 12 DSR4 Pin 13 SIN4 Pin 14 RTS4 Pin 15 SOUT4 Pin 16 CTS4 Pin 17 DTR4 Pin 18 RI4 Pin 19 GND Pin 20 N/A Pin 21 DCD Pin 22 DSR Pin 23 SIN5 Pin 24 RTS5 Pin 25 SOUT5 Pin 26 CTS5 Pin 27 DTR5 Pin 28 RI5 Pin 29 GND Pin 30 N/A Pin 31 DCD6 Pin 32 DSR6 Pin 33 SIN6 Pin 34 RTS6 Pin 35 SOUT6 Pin 36 CTS6 Pin 37 DTR6 Pin 38 RI6 Pin 39 GND Pin 30 N/A Pin 41 DCD7 Pin 42 DSR7 Pin 43 SIN7 Pin 44 RTS7 Pin 45 SOUT7 Pin 46 CTS7 Pin 47 DTR7 Pin 48 RI7 Pin 49 GND Pin 50 N/A F2_5COM COM8 COM9 COM10 COM11 COM12 Pin RS232 Pin RS232 NO. NO. Pin 1 DCD8 Pin 2 DSR8 Pin3 SIN8 Pin 4 RTS8 Pin 5 SOUT8 Pin 6 CTS8 Pin 7 DTR8 Pin 8 RI8 Pin 9 GND Pin 10 N/A Pin 11 DCD9 Pin 12 DSR9 Pin 13 SIN9 Pin 14 RTS9 Pin 15 SOUT9 Pin 16 CTS9 Pin 17 DTR9 Pin 18 RI9 Pin 19 GND Pin 20 N/A Pin 21 DCD10 Pin 22 DSR10 Pin 23 SIN10 Pin 24 RTS10 Pin 25 SOUT10 Pin 26 CTS10 Pin 27 DTR10 Pin 28 RI10 Pin 29 GND Pin 30 N/A Pin 31 DCD11 Pin 32 DSR11 Pin 33 SIN11 Pin 34 RTS11 Pin 35 SOUT11 Pin 36 CTS11 Pin 37 DTR11 Pin 38 RI11 Pin 39 GND Pin 30 N/A Pin 41 DCD12 Pin 42 DSR12 Pin 43 SIN12 Pin 44 RTS12 Pin 45 SOUT12 Pin 46 CTS12 Pin 47 DTR12 Pin 48 RI12 Pin 49 GND Pin 50 N/A 20

26 (8) GPIO_CON(10-pin): GPIO Header Pin 1 GPIO_80 GPIO_82 GPIO_84 GPIO_86 GND 2 GPIO_81 GPIO_83 GPIO_85 GPIO_87 VCC (9) SYSFAN1 (3-pin)/ CPUFAN (4-pin): FAN Headers SYSFAN1 Pin1 Fan Clock +12V Fan Power GND GND +12V Fan Power Fan Clock Control Pin1 CPUFAN 21

27 Chapter 3 Introducing BIOS Notice! The BIOS options in this manual are for reference only. Different configurations may lead to difference in BIOS screen and BIOS screens in manuals are usually the first BIOS version when the board is released and may be different from your purchased motherboard. Users are welcome to download the latest BIOS version form our official website. The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program will gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. Only when these tasks are completed done it gives up control of the computer to operating system (OS). Since the BIOS is the only channel for hardware and software to communicate, it is the key factor for system stability, and in ensuring that your system performance as its best. 3-1 Entering Setup Power on the computer and by pressing <Del> immediately allows you to enter Setup. If the message disappears before your respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the RESET button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to Press <Del> to enter Setup; press < F7> for Pop Menu. 3-2 BIOS Menu Screen 22

28 The following diagram show a general BIOS menu screen: Menu Bar General Help Items Menu Items Current Setting Value Function Keys 3-3 Function Keys BIOS Menu Screen In the above BIOS Setup main menu of, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us first see a short description of the function keys you may use here: Press (left, right) to select screen; Press (up, down) to choose, in the main menu, the option you want to confirm or to modify. 23

29 Press <Enter> to select. Press <+>/< > keys when you want to modify the BIOS parameters for the active option. [F1]: General help. [F2]: Previous value. [F3]: Optimized defaults. [F4]: Save & Exit. [F10]: Save & Reset. Press <Esc> to quit the BIOS Setup. 3-4 Getting Help Main Menu The on-line description of the highlighted setup function is displayed at the top right corner the screen. Status Page Setup Menu/Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press <Esc>. 3-5 Menu Bars There are seven menu bars on top of BIOS screen: Main Advanced Chipset Boot Security TurboOC Save & Exit To change system basic configuration To change system advanced configuration To change chipset configuration To change boot settings Password settings To change TurboOC settings Save setting, loading and exit options. 24

30 User can press the right or left arrow key on the keyboard to switch from menu bar. The selected one is highlighted. 3-6 Main Menu Main menu screen includes some basic system information. Highlight the item and then use the <+> or <-> and numerical keyboard keys to select the value you want in each item. System Date Set the date. Please use [Tab] to switch between data elements. System Time Set the time. Please use [Tab] to switch between time elements. 25

31 3-7 Advanced Menu 4 ACPI Settings Press [Enter] to make settings for the following sub-items: ACPI Settings Enable Hibernation The optional settings: [Enabled]; [Disabled]. Use this item to enable or disable system ability to hibernate (OS/S4 Sleep State). This option may not be effective with some OS. ACPI Sleep State Use this item to select the highest ACPI sleep state the system will enter when the suspend button is pressed. The optional settings are: [Suspend Disabled]; [S1 only (CPU Stop Clock)]; [S3 26

32 only (Suspend to RAM)]. ERP Support The optional settings: [Disabled]; [Enabled]. Use this item to enable or disable EUP function for this board. This item should be set as [Disabled] if you wish to have active all Wake-up functions. Wake-Up by PCIE/Lan The optional settings: [Disabled]; [Enabled]. Use this item to enable or disable PCIE device PME in S1/S3/S4/S5. *This item will only show when ERP Support is set as [Disabled]. Wake-Up by Ring The optional settings: [Disabled]; [Enabled]. Use this function to enable or disable wake-up by ring function. *This item will only show when ERP Support is set as [Disabled]. Wake-Up by PS/2 Keyboard The optional settings: [Disabled]; [Enabled]. Use this function to enable or disable PS/2 keyboard wake-up from S3/S4/S5. *This item will only show when ERP Support is set as [Disabled]. Wake-Up by PS/2 Mouse The optional settings: [Disabled]; [Enabled]. Use this function to enable or disable PS/2 mouse wake-up from S3/S4/S5. *This item will only show when ERP Support is set as [Disabled]. PWRON After PWR-Fail The optional settings: [Former-Sts]; [Always On]; [Always Off]. USB_PS2 Standby Power Support The optional settings: [Disabled]; [Enabled]. Use this function to enable or disable USB2_PS2 standby power. *This item will only show when ERP Support is set as [Disabled]. 4 RTC WakeUp Settings Press [Enter] to make settings for the following sub-items: Wake System with Fixed Time Use this item to enable or disable system wake on alarm event. When set as [Enabled], system will wake on the hour/min/sec specified. 27

33 Wake System with Dynamic Time Use this item to enable or disable system wake on alarm event. When set as [Enabled], system will wake on the current time + increased minute(s). 4 SATA Configuration Press [Enter] to make settings for the following sub-items: SATA Controller(s) Use this item to enable or disable SATA device. The optional settings: [Enabled]; [Disabled]. SATA Mode Selection Use this item to determine how SATA controller(s) operate. The optional settings are: [IDE]; [AHCI]. Smart Self Test Use this function to run SMART self test on all HDDs during POST. The optional settings are: [Disabled]; [Enabled]. SATA Controller Speed Use this item to select the maximum speed the SATA controller can support. The optional settings: [Default]; [Gen1]; [Gen2]; [Gen3]. SATA 1/SATA2/MSATA Port Support The optional settings: [Disabled]; [Enabled]. Use this item to enable or disable each SATA port. Hot Plug The optional settings: [Disabled]; [Enabled]. Use this item to designate this port as Hot Pluggable. SATA Device Type The optional settings: [Hard Disk Drive]; [Solid State Drive]. 4 PCH-FW Configuration Press [Enter] to view current ME configuration or go to ME FW Image Re-Flash to enable or disable ME FW Image Re-Flash function. ME FW Image RE-Flash Use this item to enable or disable ME FW Image Re-Flash function. The optional settings: [Disabled]; [Enabled]. 28

34 * In the case that user needs to update ME firmware, user should set ME FW Image Re-Flash as [Enabled], save the settings and exit. The system will turn off and reboot after 4 seconds. If the user goes to BIOS screen again will find this item is set again as [Disabled], but user can still re-flash to update firmware next time. 4 USB Configuration Press [Enter] to make settings for the following sub-items: Legacy USB Support The optional settings are: [Enabled]; [Disabled]; [Auto]. [Enabled]: To enable legacy USB support. [Auto]: To disable legacy support if no USB devices are connected. [Disabled]: to keep USB devices available only for EFI specification, USB3.0 Support Use this item to enable or disable USB3.0 (XHCI) controller support. The optional settings are: [Enabled]; [Disabled]. XHCI Hand-off This is workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. The optional settings are: [Disabled]; [Enabled]. EHCI Hand-off This is workaround for OSes without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver. The optional settings are: [Disabled]; [Enabled]. USB Mass Storage Driver Support The optional settings are: [Disabled]; [Enabled]. 4 Super I/O Configuration Press [Enter] to make settings for the following sub-items: Super IO Configuration 4 Serial Port 1 Configuration/Serial Port 2 Configuration Press [Enter] to make settings for the following items: Serial Port Use this item to enable or disable serial port (COM). Change Settings 29

35 Use this item to select an optimal setting for super IO device. Transmission Mode Select The optional settings are: [RS422]; [RS232]; [RS485]. Mode Speed Select The optional settings are: [RS232=1Mbps, RS422/RS485=10Mbps]; [RS232/ RS422/RS485=250Kbps]. 4 Serial Port 3 Configuration / Serial Port 4 Configuration/ Serial Port 5 Configuration/Serial Port 6 Configuration Press [Enter] to make settings for the following items: Serial Port Use this item to enable or disable serial port (COM). Change Settings Use this item to select an optimal setting for super IO device. WatchDog Timer Use this item to enable or disable WatchDog Timer control. *When set as [Enabled], the following sub-items shall appear: WatchDog Timer Value User can set a value in the range of [1] to [255]. WatchDog Timer Unit The optional settings are: [Sec.]; [Min.]. Case Open Detect This item controls detect case open function. The optional settings: [Disabled]; [Enabled]. 4 F81866 H/W Monitor Press [Enter] to view current CPU health status and make settings for the following sub-items: Shutdown Temperature Use this item to select system shutdown temperature. The optional settings are: [Disabled]; [60 o C/140 o F]; [65 o C/149 o F];[70 o C/158 o F] [75 o C/167 o F]. CPUFAN Smart Mode Press [Enter] to make settings for Smart Fan Configuration: 30

36 The optional settings are: [Disabled]; [Enabled]. *When set as [Enabled], the following sub-items shall appear: CPUFAN Highest Speed Temp Use this item to select a value at which the fan will run at full speed when the temperature is higher than this pre-set temperature value limit. The optional setting ranges: [Min Idle Temp.] ~ [Max=100C]. CPUFAN Idle Temp Use this item to select a value at which the fan will run at idle speed when the temperature is lower t this pre-set temperature value limit. The optional setting ranges: [Min=0C.] ~ [Max Full-speed Temp]. 4 SECOND Super I/O Configuration Press [Enter] to make settings for the following sub-items: SECOND Super IO Configuration 4 Serial Port 7 Configuration/Serial Port 8 Configuration/Serial Port 9 Configuration/Serial Port 10 Configuration/Serial Port 11 Configuration/Serial Port 12 Configuration Press [Enter] to make settings for the following items: Serial Port Use this item to enable or disable serial port (COM). Change Settings Use this item to select an optimal setting for super IO device. 31

37 3-8 Chipset Menu 4 PCH-IO Configuration Press [Enter] to make settings for the following sub-items: 4 USB Configuration Press [Enter] to further setting USB configuration settings. USB Configuration USB Precondition Use this item to precondition work on USB host controller and root ports for faster enumeration. The optional settings are: [Enabled]; [Disabled]. XHCI Mode Use this item to select mode of operation of XHCI controller. 32

38 The optional settings are: [Smart Auto]; [Auto]; [Enabled]; [Disabled]; [Manual]. *When set as [Disabled], user can make settings in EHCI1/EHCI2 items that appear: EHCI1/ EHCI2 Use this item to enable or disable USB EHCI (USB 2.0) support. One EHCI controller must always be enabled. The optional settings are: [Enabled]; [Disabled]. *When set as [Manual], user can make settings in the following items that appear: XHCI1 Pre-Boot Driver Use this item to enable or disable XHCI pre-boot driver support. The optional settings are: [Enabled]; [Disabled]. Route USB 2.0 pins to which HC? The optional settings are: [Route Per-Pin]; [Route all Pins to EHCI]; [Route all Pins to XHCI]. Enable USB 3.0 pins The optional settings are: [Select Per-Pin]; [Disable all Pins]; [Enable all Pins]. USB Ports Per-Port Disable Control Use this item to control each of the USB ports disabling. The optional settings are: [Enabled]; [Disabled]. PCIE2USB3.0 Support The optional settings are: [Disabled]; [Enabled]. Onboard PCIE Lan1/ Onboard PCIE Lan2 Use this item to control the Onboard PCIE Lan. The optional settings are: [Disabled]; [Enabled]. MINIPCIE The optional settings are: [Disabled]; [Enabled]. MINI_CARD The optional settings are: [Disabled]; [Enabled]. Onboard Lan BootROM Use this item to enable or disable boot option ROM for onboard network devices. The optional settings are: [Disabled]; [Enabled]. Subtractive Decode Use this item to enable or disable PCI Express subtractive decode. 33

39 The optional settings are: [Disabled]; [Enabled]. *When set as [Enabled], user can make settings in the following items that appear: Subtractive Decode Port# Use this item to select PCI Express subtractive decode root port. The optional settings are: [MINIPCIE]; [MINI_CARD]. Azalia Use this item to control the detection of the Azalia Audio device. The optional settings are: [Disabled]; [Enabled]. [Disabled]: Azalia will be unconditionally disabled; [Enabled]: Azalia will be unconditionally enabled; When set as [Enabled], user can make settings in Azalia Internal HDMI Codec that appears: Azalia Internal HDMI Codec Use this item to enable or disable internal HDMI codec for Azalia. The optional settings are: [Enabled]; [Disabled]. 4 System Agent (SA) Configuration Press [Enter] to make settings for the following sub-items: VT-d Use this item to enable or disable VT-d function on MCH. The optional settings are: [Enabled]; [Disabled]. *This item might not be available depending on configuration. Primary Display The optional settings are: [Auto]; [IGFX]; [PEG]. Internal Graphics The optional settings are: [Auto]; [Disabled]; [Enabled]. Aperture Size The optional settings are: [128MB]; [256MB]; [512MB]. DVMT Pre-Allocated Use this item to select DVMT 5.0 pre-allocated (fixed) graphics memory size used by the internal graphics device. The optional settings are: [32M]; [64M]; [96M]; [128M]; [160M]; [192M]; [224M]; [256M]; [288M]; [320M]; [352M]; [384M]; [416M]; [448M]; [480M]; [512M]; [1024M]. DVMT Total Gfx Mem 34

40 Use this item to select DVMT 5.0 total graphics memory size used by the internal graphics device. The optional settings are: [128M]; [256M]; [MAX]. RC6(Render Standby) Use this item to enable or disable render standby support. The optional settings are: [Disabled]; [Enabled]. DMI Link ASPM Control The optional settings are: [Disabled]; [L0s]; [L1]; [L0Sl1]. DMI Gen 2 The optional settings are: [Auto]; [Enabled]; [Disabled]. Enable PEG The optional settings are: [Disabled]; [Enabled]; [Auto]. *When set as [Enabled] or [Auto], user can make settings in the following items that appear: PEG-Gen X The optional settings are: [[Auto]; [Gen1] ;[Gen2] ;[Gen3]. Detect Nom-Compliance Device The optional settings are: [Disabled]; [Enabled]. PEG-ASPM The optional settings are: [Disabled]; [Auto]; [ASPM L0s]; [ASPM L1]; [ASPM L0Sl1]. VGA2 Support The optional settings are: [Disabled]; [Enabled]. 35

41 3-9 Boot Menu Boot Configuration Setup Prompt Timeout Use this item to set number of seconds to wait for setup activation key. Bootup Numlock State Use this item to select keyboard numlock state. The optional settings are: [On]; [Off]. Fast Boot The optional settings are: [Enabled]; [Disabled]. When set as [Enabled], user can make settings in the following items that appear: SATA Support The optional settings are: [Last Boot HDD Only];[All SATA Devices]; [HDD Only]. 36

42 VGA Support The optional settings are: [Auto]; [EFI Driver]. *When set as [Enabled], it will only install Legacy OpROM with Legacy OS and logo will not be shown during POST. EFI driver will still be installed with EFI OS. USB Support The optional settings are: [Disabled]; [Full Initial]; [Partial Initial]. PS2 Devices Support The optional settings are: [Disabled]; [Enabled]. The PS2 devices will be skipped if this is set as [Disabled]. Network Stack Driver Support The optional settings are: [Disabled]; [Enabled]. Network Stack Driver will be skipped if this is set as [Disabled]. Boot Option Priorities Boot Option #1/ Use this item to decide system boot order from available options. 4 CSM parameters Press [Enter] to make settings for the following sub-items: Launch CSM The optional settings are: [Enabled]; [Disabled]. Boot option filter This option controls what device system can boot to. The optional settings are: [UEFI and Legacy]; [Legacy only]; [UEFI only]. Launch Storage OpROM policy This option controls the execution of UEFI and Legacy Storage OpROM. The optional settings are: [Do not launch]; [UEFI only]; [Legacy only]. Launch Video OpROM policy This option controls the execution of UEFI and Legacy Video OpROM. The optional settings are: [Do not launch]; [UEFI only]; [Legacy only]; [Legacy first]; [UEFI first]. Other PCI device ROM priority This item is for PCI devices other than Network, Mass storage or video defines which OpROM to launch. The optional settings are: [UEFI OpROM]; [Legacy OpROM]. 37

43 3-10 Security Menu Administrator Password This item allows user to set administrator password. User Password This item allows user to set user password. 38

44 3-11 TurboOC Menu 4 CPU Configuration Press [Enter] to view current CPU information and make settings for the following sub-items: Active Processor Cores Use this item to set the number of cores to enable in each processor packages. Limit CPUID Maximum The optional settings are: [Disabled]; [Enhanced]. This item should be set as [Disabled] for Windows XP. Execute Disable Bit The optional settings are: [Disabled]; [Enhanced]. 39

45 Intel Virtualization Technology The optional settings are: [Disabled]; [Enabled]. When set as [Enabled], a VHM can utilize the additional hardware capabilities provided by Vanderpool Technology. EIST The optional settings are: [Disabled]; [Enabled]. *When set as [Enabled], user can make settings in the following items that appear: Turbo Mode The optional settings are: [Enabled]; [Disabled]. *When set as [Enabled], user can make settings in Torbo Core Ratio Limit : Turbo Core Ratio Limit This item is for user to set Turbo core ratio. 0 means using the factory-configured value. CPU C states The optional settings are: [Disabled]; [Enabled]. *When set as [Enabled], user can make settings in the following items that appear: Enhanced C1 State The optional settings are: [Disabled]; [Enabled]. CPU C3 Report The optional settings are: [Disabled]; [Enabled]. Use this item to enable or disable CPU C3 report to OS. CPU C6 Report The optional settings are: [Disabled]; [Enabled]. Use this item to enable or disable CPU C6 report to OS. C6 Latency The optional settings are: [Short]; [Long]. Use this item to configure short/long latency for C6. 40

46 CPU C7 Report The optional settings are: [Disabled]; [CPUC7]; [CPUC7s]. Use this item to enable or disable CPU C7 report to OS. C7 Latency The optional settings are: [Short]; [Long]. Use this item to configure short/long latency for C7. LakeTiny Feature Use this item to enable or disable LakeTiny for Cstate configuration. The optional settings are: [Disabled]; [Enabled]. 4 Memory Configuration Press [Enter] to make settings for the following sub-items: DIMM profile Use this item to select DIMM timing profile that should be used. The optional settings are: [Default DIMM profile]; [Custom Profile]. *When set as [Custom Profile], the sub-item Custom Profile Control will appear for user to manually set memory timing configuration: tcl The setting range for Cas Latency is from [4] to [18]. trcd The setting range for Row to Col Delay is from [1] to [38]. trp The setting range for Ras Precharge is from [1] to [38]. tras The setting range for Ras Active Time is from [1] to [586]. twr The setting range for Min Write Recovery Time is from [1] to [38]. trfc The setting range for Min Refresh Recovery Delay Time is from [1] to [9363]. trrd The setting range for Min Row Active to Row Active Delay Time is from [1] to [38]. twtr The setting range for Min Internal Write to Read Command Delay Time is from 41

47 [1] to [38]. trtp The setting range for Min Internal Read to Precharge Command Delay Time is from [1] to [38]. trc The setting range for Min Active to Active/Refresh Delay Time(tRCmin) to Precharge Command Delay Time is from [1] to [586]. tfaw The setting range for Min Four Activate Window Delay Time is from [1] to [586]. tcwl The setting range for Minimum CAS Write Latency Time (tcwlmin). trefi The setting range for Maximum trefi Time (Average Periodic Refresh Interval). Memory Frequency Limiter Use this item to set maximum memory frequency selection in Mhz. The optional settings are [Auto]; [1066]; [1333] [1600]. Command Rate The optional settings are: [Auto]; [1T]; [2T]. 42

48 3-12 Save & Exit Menu Save Changes and Reset This item allows user to reset the system after saving the changes. Discard Changes and Reset This item allows user to reset the system without saving any changes. Save Options Save Changes This item allows user to save changes done so far to any of the setup options. Discard Changes This item allows user to discard changes done so far to any of the setup options. Restore Defaults Use this item to restore /load default values for all the setup options. 43

49 Save as User Defaults Use this item to save the changes done so far as user defaults. Restore User Defaults Use this item to restore defaults to all the setup options. Boot Override Launch EFI Shell from filesystem device Use this item to launch EFI shell application (Shell x 64.efi) from one of the available filesystem devices. 44