BYT60 Motherboard User s Manual Version 2.0

Transcription

1 BYT60 Motherboard User s Manual Version 2.0 Chapter 1 Product Introduction 1.1 Motherboard Specification Platform: Onboard Intel BayTrail-D Celeron Processor J1800, Core Frequency 2.41Ghz, power consumption 10W Onboard Intel Bay Trail-D Celeron Processor J1900, Core Frequency 2.00Ghz, power consumption 10W Memory: Single Channel DDR3L 1333Mhz, Up to 8GB system memory Graphic: Integrated graphic processor - Intel HD graphic support Storage: 2X SATA2.0, 1X msata via mini PCIe slot, SATA2 and msata either one, 1X emmc(optional) USB: Maximum 8X USB ports with 1x USB3.0 included. Display: 1x HDMI, 1x VGA, 1x dual-channel 24bit LVDS and dual display support Ethernet: Onboard 2x Gigabyte internet controller RTL8111F, 1x RJ45 and 2x USB2.0 co-layout Sound: Onboard integrated HD audio chipset ALC662 supports Speaker-out, MIC-in and S/PDIF and amplifier I/O: IT8786E support 6x serial COM, 1x LPT, COM2 can do eitherrs232 or RS485. IT8772E support COM1 only. Other I/O: 2x mini PCIe slots with either 1x msata and 1 slot for wifi, 3G/4G or 2x Mini PCie/USB slots support WIFI plus 3G/4G module. 1x LPT; GPIO and 1x PS/2 for keyboard and mouse Form Factor: 170mm x 170mm Power supply: DC-IN 12V Power, and 1x 4pin ATX 1

2 2.1 Board Placement Chapter 2 Hardware Function F-AUDIO Speaker JHDMI USB2.0 LVDS or LVDS_ADJ EdDP COM3-6 SIM CARD J2 Mini-PCIE 2*PWSATA 2*SATA 2*COM PS/2 emmc msata DIMM JGPIO JPOWER USB2.0 Please LPT take care JAT to connect CLR_MOS external devices for as not to damage the board! Jumper Function Setting Before hardware device installation, please check following table. Tip: How to identify jumper pin no., observe pin no.1 mark on the board, Mark No.1 or bold strip or triangle symbol: look at the back, see rectangle pin no.1; all jumper pin no.1 2

3 shows 1 white arrow sign Memory Slot Onboard 1x DDR3L 1333MHz SO-DIMM memory slot, memory capacity up to 8GB Internal display Header (JHDMI, JVGA) One 14pin JHDMI and one 12 pin JVGA pin JHDMI: DVI1_DATA2_P 1 2 DVI1_DATA2_N DVI1_DATA1_P 3 4 DVI1_DATA1_N DVI1_DATA0_P 5 6 DVI1_DATA0_N DVI1_CLK_P 7 8 DVI1_CLK_N DVI1_SCL 9 10 DVI1_SDA VGA_DATA_5V GND DVI1_DETECT GND JVGA: 1 CRT_DDC_ DATA 2 CRT_DDC_ CLK 3 GND 4 VGA_B_R 5 GND 6 VGA_G_R 7 GND 8 VGA_R_R 9 GND 10 CRT_HSYNC1 11 CRT_VSYNC1 12 VGA_DVI_5V 3

4 2.1.4 Internal Power Supply (PWR2) 1 +12V 2 +12V 3 GND 4 GND Internal USB pin (USB1, USB2) Onboard USB header for USB2.0 port USB1 USB2:. 5V 1 2 5V USB DATA- 3 4 USB DATA- USB DATA+ 5 6 USB DATA+ GND 7 8 GND 9 10 NUL LAN Onboard gigabyte internet controller chipset RTL8111F, Link LED flashes, Action LED flashes when data transmission. RJ45 LAN LED:RJ45 LAN LED Status LILED (Green) Function ACTLED (Yellow) Function Flash Mode Network Connected Flashing Data Transmitting 4

5 2.1.7(FP_AUDIO, JAUD,JSPIF)Audio Header Realtek ALC662 audio controller chipset, Green is the audio output port (Speaker-Out), Pink is MIC-in audio input port; JAUD is audio amplifier and JSPIF is fiber digital audio signal. FP_AUDIO: Front Panel Audio (FP-Audio) MIC2-L 1 2 AGND MIC2-R 3 4 AVCC FRO-R 5 6 MIC2-JD F-IO-SEN(AGNG) 7 8 NC FRO-L 9 10 LIN2-JD JAUD: 1 L+ 2 L- 3 R- 4 R+ JSPIF: 1 +5V 2 SPDIF Out 3 GND 5

6 2.1.8 LVDS ( JLVDS,LVDS_ADJ & J2 ) Dual-channel 24bit LVDS header, VCC of LVDS power cable supply can be choose by J2 control, LVDS_ADJ use for LVDS back-light power control. JLVDS1: VCC 1 2 VCC VCC 3 4 GND GND 5 6 GND A_DATA0_DN 7 8 A_DATA0_DP A_DATA1_DN 9 10 A_DATA1_DP A_DATA2_DN A_DATA2_DP GND GND A_CLK_DN A_CLK_DP A_DATA3_DN A_DATA3_DP B_DATA0_DN B_DATA0_DP B_DATA1_DN B_DATA1_DP B_DATA2_DN B_DATA2_DP GND GND B_CLK_DN B_CLK_DP B_DATA3_DN B_DATA3_DP LVDS_ADJ: 1 12V 2 12V 3 LCD_BKL_ON 4 LCD_BKL_ADJ 5 GND 6 GND 6

7 J2:LVDS Power Setting Function 1-2 Close VCC(+3.3V) 3-4 Close VCC(+5V) 5-6 Close VCC(+12V) Attention: You can choose 12V/5V/3.3V between the three flexible adjustments. Customer according to the LVDS voltage specification, use the jumper cap to meet the requirements of the VCC interface 2pin short (it is strictly forbidden to use 2 or more interfaces in same time using the jumping Cap short) edp(edp/lvds EDp/LVDS_ADJ J2) Optional edp and LVDS could select either one only. Version and board functions need to decided before production, can t be used at the same time. edp( 丝印 :EDp/LVDS): Defintion PIN No. Defintion VCC 1 2 VCC VCC 3 4 EDP_HPD GND 5 6 GND EDP_AUXN 7 8 EDP_AUXP N/A 9 10 N/A EDP_DATA0_P EDP_DATA0_N GND GND N/A N/A EDP_DATA1_P EDP_DATA1_N N/A N/A N/A N/A N/A N/A GND GND N/A N/A N/A N/A edp Backlight( 丝印 :EDp/LVDS_ADJ): PIN 1 12V 2 12V 7

8 3 LCD_BKL_ON 4 LCD_BKL_ADJ 5 GND 6 GND edp Power( 丝印 :J2): Pin 1-2 Close VCC(+3.3V) 3-4 Close VCC(+5V) 5-6 Close VCC(+12V) Serial COM(JCOM1,JCOM2,JCOM36,JCOM2_P,JCOM4_P) Provides 6x COM supports RS232. COM1 and COM2 defines as industrial definition; JCOM2 and JCOM4 provides 5V/12V by jumper. JCOM1: DCD# 1 2 DSR# RXD 3 4 RTS# TXD 5 6 CTS# DTR# 7 8 RI# GND 9 10 JCOM2 RS232 or RS485, Pin : RS232 RS485 1 DCD DATA- 2 DSR NC 3 RXD DATA+ 4 RTS NC 5 TXD NC 6 CTS NC 7 DTR NC 8 RI NC 9 GND GND JCOM3 to JCOM6 : 8

9 DCD# 1 2 RXD TXD 3 4 DTR# GND 5 6 DSR# RTS# 7 8 CTS# RI# 9 10 DCD# RXD TXD DTR# GND DSR# RTS# CTS# RI# DCD# RXD TXD DTR# GND DSR# RTS# CTS# RI# DCD# RXD TXD DTR# GND DSR# RTS# CTS# RI# JCOM2 ; JCOM4: PIN No Setting Function 1-2 Close 5V 3-4 Close RI 5-6 Close 12V Parallel Port (LPT) Onboard 1x 2x13pin LPT header 9

10 LPT: STB 1 2 AFD LPT_ PPD0 3 4 ERROR LPT_ PPD1 5 6 INIT LPT_ PPD2 7 8 SLIN LPT_ PPD GND LPT_ PPD GND LPT_ PPD GND LPT_ PPD GND LPT_ PPD GND ACK GND BUSY GND PE GND SLCT NC JGPIO 4 input and 4 Output GPI_S5_ V GPI_S5_1 3 4 GPO_S5_6 GPI_S5_2 5 6 GPO_S5_7 GPI_S5_3 7 8 GPO_S5_8 GND 9 10 GPO_S5_ SATA and msata (SATA1,mSATA,PWSATA1) Provides 2x standard SATA2.0 port (SATA2 and msata either one) and 2x 4pin SATA Power PWSATA1:PWSATA1 Pin 1 +5V 2 GND 3 GND 10

11 4 +12V emmc (Optional) emmc support UEFI operation system such as Windows 10 64bit, Windows 8 64bit and Linux 64bit (MINI-PCIE,SIM1)Mini-PCIe One mini PCI-e slot support WIFI module or 3G/4G Module with 1x SIM card slot PS/2 header 1 +5V 2 KB_DATA 3 KB_CLK 4 MS_ DATA 5 MS_CLK 6 GND Front Panel Power Pin Front control panel header is used to connect to the chassis front panel established by the function buttons and LEDs. JPOWER1:Power Pin HDD_LED+ 1 2 PWR_LED+ HDD_LED- 3 4 PWR_LED- RSTBTN+ 5 6 PWR_ON+ RSTBTN- 7 8 PWR_ON- NUL Auto Power On (JAT) JAT: Setting Close JAT auto power on 11

12 CMOS Clear / Default as Setting CMOS powered by the onboard button cell battery, clearing CMOS will lead to the permanent elimination of system setup (Default as factory setting) Steps: 1. Turn off your computer, disconnect the power supply 2. Use a jumper CAP shorts circuit function on JCOMS socket, holds for 3 to 5 seconds, then disconnect. 3. Starts the computer, press DEL button, enter into BIOS setting, reload optimal defaults 4. Save and Exit JCOMS: Setting Close JCMOS Clear CMOS setting motherboard! Please do not clear CMOS when computer is on, so as to damage the 12