TECHNICAL MANUAL. Intel 1037U CPU + Intel NM70 Chipset. Based Mini-ITX M/B

Transcription

1 TECHNICAL MANUAL Of Intel 1037U CPU + Intel NM70 Chipset Based Mini-ITX M/B SYS7F880VGGA-OM Revision: 3.0 Release date: May 8, 2014 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

2 Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding. To minimize pollution and ensure environment protection of mother earth, please recycle. i

3 TABLE OF CONTENT ENVIRONMENTAL SAFETY INSTRUCTION...iii USER S NOTICE...iv MANUAL REVISION INFORMATION...iv ITEM CHECKLIST...iv CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD 1-1 FEATURE OF MOTHERBOARD SPECIFICATION LAYOUT DIAGRAM...3 CHAPTER 2 HARDWARE INSTALLATION 2-1 JUMPER SETTING CONNECTORS AND HEADERS CONNECTORS HEADERS...15 ii

4 Environmental Safety Instruction Avoid the dusty, humidity and temperature extremes. Do not place the product in any area where it may become wet. 0 to 60 centigrade is the suitable temperature. (The figure comes from the request of the main chipset) Generally speaking, dramatic changes in temperature may lead to contact malfunction and crackles due to constant thermal expansion and contraction from the welding spots that connect components and PCB. Computer should go through an adaptive phase before it boots when it is moved from a cold environment to a warmer one to avoid condensation phenomenon. These water drops attached on PCB or the surface of the components can bring about phenomena as minor as computer instability resulted from corrosion and oxidation from components and PCB or as major as short circuit that can burn the components. Suggest starting the computer until the temperature goes up. The increasing temperature of the capacitor may decrease the life of computer. Using the close case may decrease the life of other device because the higher temperature in the inner of the case. Attention to the heat sink when you over-clocking. The higher temperature may decrease the life of the device and burned the capacitor. iii

5 USER S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE DO ASSURE THIS MANUAL MEETS USER S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE). PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER S BENEFIT, WITHOUT INTENT TO INFRINGE. Manual Revision Information Reversion Revision History Date 3.0 Third Edition May 8, 2014 Item Checklist Motherboard DVD for motherboard utilities User s Manual Cable(s) I/O Back panel shield iv

6 Chapter 1 Introduction of the Motherboard 1-1 Feature of Motherboard Intel 1037U dual-core CPU+ Intel NM70 express chipset Support 1 * DDRIII slot for SO-DIMM 1066/1333 MHz up to 8GB Support 2 * SATAII (3Gb/s) Devices Support half-size Mini-PCIE connector Support m-sata connector Integrated with 24-bit dual channel LVDS header Support HDMI and VGA Video Outputs Support CPU Smart FAN Support Watchdog Timer Technology Support Windows8 OS Support slim fan design Support Thunder Protection Function Compliance with EuP Standard 1

7 1-2 Specification Spec 2 Description Design 6-layer PCB size: 16.8 x 12.0 cm Embedded CPU Intel 1037U Dual Core CPU (1.8GHz) Chipset Intel NM70 Express Chipset 1* DDRIII SO-DIMM slot to support DDRIII 1066/1333 MHz Memory DDRIII SO-DIMM expandable to 8GB SYS7F880VGGA-OM : onboard 2G DRAM Expansion Slot 1 *halt-size Mini-PCIE slot 1* SIM slot Storage 2* SATA II 3G/s Connector 1 * M-SATA Connector LAN Chip Audio Chip BIOS Multi I/O Integrated with Realtek RTL8111G PCI-E Gigabit LAN chip Support Fast Ethernet LAN function of providing 10/100/1000Mbps Ethernet data transfer rate Realtek ALC887 HD Audio Codec integrated Audio driver and utility included 32M DIP Flash ROM Rear Panel I/O: 1* COM Port 1 * VGA port 2* USB 2.0/1.1 port 2* RJ-45 port 1* Line-Out port Internal I/O Connectors& Headers: 1 *4-pin 10V~24V Internal Power connector 1 *4-pin SATA Power connector 1 * Front panel header 2 * 9-Pin USB 2.0/1.1 header for four USB 2.0/1.1 ports

8 5* COM header 1* TX-RXCOM header 1 * Parallel header 1 *GPIO header 1 *12-pin VGA header 1 *20-pin HDMI header 1 *24-bit Dual Channel LVDS header 1* LVDS inverter header JP3: 1*LVDS panel brightness adjustment header 1*CPU fan header 2*System fan header 1-3 Layout Diagram Rear IO Diagram COM1 Port VGA Port USB 2.0 Ports RJ-45 LAN Port Line-Out Port RJ-45 LAN Port 3

9 Motherboard Internal Diagram--Front 10V~24V Power Connector SYSFAN3 Header Intel CPU COM1 Port * DRAM 2G Onboard (Optional for NL70-IE1037-2G) DDRIII SODIMM Slot VGA Port HDMI Header VGA Header SYSFAN1 Header USB 2.0 Ports RJ-45 LAN Port Intel NM70 Chipset LVDS Header LVDS Inverter M-SATA Connector CPUFAN1 Header USB 2.0 Header GPIO Header Parallel Port Header RJ-45 LAN Port Line-Out Port SPEAKER_CON Header JP3 COM Port Headers TX-RX COM1 Header SATAII Ports Half-size Mini-PCIE Connector Front Panel Header Power Switch Button Reset Button SATA Hard Disk Power-Out Connector 4

10 The other diagrams used for illustration in this manual are from model NL70-IE1037, unless otherwise stated. Motherboard Internal Diagram--Back SIM Card Slot 5

11 Motherboard Jumper Position JCOMP1 JCOM1 AT_MODE1 JBAT JCOMP3 JP1 JCOMP2 JP2 6

12 Jumper Jumper Name Description JBAT CMOS RAM Clear Function Setting 3-pin Block JP1 INVERTER1 VCC 3.3V/5V/12V Select 4-pin Block JP2 LVDS1 VCC 3.3V/5V/12V Select 4-pin Block JCOMP3 COM3 Header Pin9 Function Select 4-Pin Block JCOMP2 COM2 Header Pin9 Function Select 4-Pin Block JCOMP1 COM1 Header Pin9 Function Select 4-Pin Block JCOM1 COM1 Header RS232/RS485/RS422 Select 6-Pin Block AT_MODE1 AT MODE Function Select 2-pin Block Connectors Connector DCIN1 COM1 VGA USB1 LAN1/LAN2 AUDIO2 SATA1/2 PWOUT1 MINI_CARD MSATA Name ATX 12V Power Connector Serial Port Connector Video Graphic Attach Connector USB 2.0 Port Connector x2 RJ-45 LAN Connector x2 Audio Line-Out Connector SATAII Connector x2 SATA Power out Connector Half-size Mini-PCIE Connector Mini-SATA Connector 7

13 Headers Header Name Description JW_FP1 Front Panel Header(PWR LED/ HD 8-pin Block LED/Power Button /Reset) USB2/USB3 USB 2.0 Port Header 9-pin Block COM2/3/4/5/6 Serial Port Header 9-pin Block TX_RXCOM1 TX_RXCOM1 Header PARALLEL1 Parallel Port Header 25-pin Block GPIO1 GPIO Header 10-pin block VGA1 VGA Header 12-pin Block HDMI1 HDMI Header 20-pin Block LVDS1 LVDS Header 30-pin Block INVERTER1 LVDS Inverter 6-pin Block SPEAKER_CON Speaker Header 4-pin Block JP3 LVDS Panel Brightness Adjustment 2-pin Block Header CPUFAN FAN Header 4-pin Block SYSFAN1/SYSFAN3 SYSFAN Headers 3-pin Block 8

14 Chapter 2 Hardware Installation 2-1 Jumper Setting (1) JBAT (3-pin): CMOS RAM Clear Function Setting JBAT Closed: Normal; 2-3 Closed:Clear CMOS CMOS Clear Setting (2) JP1 (4-pin): INVERTER1 VCC 3.3V/5V /12V Select JP Closed: Inverter Backlight VCC= 3.3V; 3-4 Closed: Inverter Backlight VCC= 5V; 4-6 Closed: Inverter Backlight VCC= 12V. 9

15 (3) JP2 (4-pin): LVDS1 VCC 3.3V/5V/12V Select JP Closed: LVDS1 VCC= 3.3V; 3-4 Closed: LVDS1 VCC= 5V; 4-6 Closed: LVDS1 VCC= 12V. (4) JCOMP3 (6-pin): COM3 Header Pin9 Function Select JCOMP3 COM3 Header Closed: RI=RS232; 3-4 Closed: RI= 5V; 4-6 Closed: RI= 12V. 10

16 (4) JCOMP2 (6-pin): COM2 Header Pin9 Function Select JCOMP2 COM2 Header Closed: RI=RS232; 3-4 Closed: RI= 5V; 4-6 Closed: RI= 12V. (5) JCOMP1 (6-pin): COM1 Port Pin9 Function Select JCOMP1 COM1 Port Closed: RI=RS232; Closed: RI= 5V; Closed: RI= 12V. 11

17 (6) JCOM1 (6-pin): COM1 Port RS232/RS485/RS422 Function Select JCOM1 COM1 Port Closed: RS232; 3-4 Closed : RS485; 5-6 Closed : RS422. (7)AT_MODE1 (2-pin): AT Mode Function Select AT_MODE1 1-2 Open: Normal; 1-2 Short: AT_Mode Select. Pin 1-2 closed: AT_MODE function is enabled. In this case your computer will automatically turns on after a sudden power failure when power supply resumes. 12

18 2-2 Connectors and Headers Connectors (1) Rear IO Diagram Connectors COM1 Port VGA Port USB 2.0 Ports RJ-45 LAN Port Line-Out Port RJ-45 LAN Port (2) DCIN1 (4-pin block):10v~24v Power Connector Pin1 Pin No. Definition 1 GND 2 GND 3 +10V~+24V 4 +10V~+24V 13

19 (3) SATA1/SATA2:SATAII Port connector This connector is a high-speed SATAII port that supports 3 GB/s transfer rate. Pin No. Defnition 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND (4) PWOUT1(4-pin): SATA Hard Disk Power-out Connector Pin 1 +5V GND GND +12V 14

20 2-2-2 Headers (1) JW-FP1 (9-pin): Front Panel Header RSTSW PWRBTN GND GND HDDLED- HDDLED+ PWRLED+ PWRLED- 2 Pin 1 (2) USB2/USB3 (9-pin): USB 2.0 Port Header NC GND +DATA -DATA VCC Pin 1 GND +DATA -DATA VCC 15

21 (3) COM2/3/4/5/6 (9-Pin): Serial Port Headers CTS RI RTS DSR DCD SIN SOUT DTR GND Pin1 Pin6 Pin6 Pin1 CTS RI RTS COM2/3 DSR DCD SOUT SIN DTR COM4/5/6 GND (4) TX_RXCOM1(4-Pin): RS422/485 Header Pin 1 3 TXDN RXDN TXDP RXDP

22 (5) PARALLEL1 (25-pin): Parallel Port Header Pin 14 Pin1 Pin NO. Pin Definition Pin NO. Pin Definition Pin 1 STB- Pin 14 AFD- Pin 2 PRD0 Pin 15 ERR- Pin 3 PRD1 Pin 16 INIT- Pin 4 PRD2 Pin 17 SLIN- Pin 5 PRD3 Pin 18 GND Pin 6 PRD4 Pin 19 GND Pin 7 PRD5 Pin 20 GND Pin 8 PRD6 Pin 21 GND Pin 9 PRD7 Pin 22 GND Pin 10 ACK- Pin 23 GND Pin 11 BUSY Pin 24 GND Pin 12 PE Pin 25 GND Pin 13 SLCT 17

23 (6) GPIO1 (10-pin): GPIO Header VCC GPIO_71 GPIO_69 GPIO_39 GPIO_34 2 Pin 1 GND GPIO_70 GPIO_68 GPIO_38 GPIO_57 (7) VGA1 (12-pin): VGA Header Pin 1 Pin No. Definition 1 VCC5(Reserved) 2 VGA_VSYNC 3 VGA_HSYNC 4 GND_RED 5 RED_VGA 6 GND_GRN 7 GRN_VGA 8 GND_BLUE 9 BLUE_VGA 10 GND 11 DDC_DATA 12 DDC_CLK 18

24 (8) HDMI1 (20-pin): HDMI Header Pin 2 Pin1 HDMI1 Header Pin NO. Pin Definition Pin NO. Pin Definition Pin 1 GND Pin 2 HDMI_TXP2 Pin 3 HDMI_TXP1 Pin 4 HDMI_TXN2 Pin 5 HDMI_TXN1 Pin 6 GND Pin 7 GND Pin 8 HDMI_TXP0 Pin 9 HDMI_TXCP Pin 10 HDMI_TXN0 Pin 11 HDMI_TXCN Pin 12 GND Pin 13 NC Pin 14 NC Pin 15 HDMI_SDA Pin 16 HDMI_SCL Pin 17 HDMI_+5V Pin 18 GND Pin 19 GND Pin 20 HDMI_HPD 19

25 (9) LVDS1 (30-Pin): 24-bit dual channel LVDS Header Pin 1 Pin2 LVDS1 Header Pin NO. Pin Define Pin NO. Pin Define Pin 1 LVDS_VCC Pin 2 LVDS_VCC Pin 3 LVDS_VCC Pin 4 GND Pin 5 GND Pin 6 GND Pin 7 LVDSA_DATAN0 Pin 8 LVDSA_DATAP0 Pin 9 LVDSA_DATAN1 Pin 10 LVDSA_DATAP1 Pin 11 LVDSA_DATAN2 Pin 12 LVDSA_DATAP2 Pin 13 GND Pin 14 GND Pin 15 LVDSA_CLKN Pin 16 LVDSA_CLKP Pin 17 LVDSA_DATAN3 Pin 18 LVDSA_DATAP3 Pin 19 LVDSB_DATAN0 Pin 20 LVDSB_DATAP0 Pin 21 LVDSB_DATAN1 Pin 22 LVDSB_DATAP1 Pin 23 LVDSB_DATAN2 Pin 24 LVDSB_DATAP2 Pin 25 GND Pin 26 GND Pin 27 LVDSB_CLKN Pin 28 LVDSB_CLKP Pin 29 LVDSB_DATAN3 Pin 30 LVDSB_DATAP3 20

26 (10) INVERTER1 (6-Pin): LVDS1 Inverter Header Pin 1 Pin No. Definition 1 BKLT_PWR1 2 BKLT_PWR2 3 BKLT_EN 4 BKLT_PWM 5 GND1 6 GND2 (11) JP3 (2-pin): LVDS Panel Brightness Adjustment Header Pin1 Brighteness- Brighteness+ 21

27 (12) SPEAKER_CON (4-pin): Speaker Header Pin1 L- L+ R+ R- (13) CPUFAN1 (4-pin): CPUFAN Header Control Fan Speed +12V Fan Power GND Pin1 CPUFAN1 22

28 (14) SYSFAN1/SYSFAN3 (3-pin): FAN Headers Fan Speed +12V Fan Power GND Pin1 SYSFAN3 SYSFAN1 Pin1 Fan Speed +12V Fan Power GND 23