Annexure-1 (CC no )
|
|
- Melvyn Pitts
- 6 years ago
- Views:
Transcription
1 Annexure-1 (CC no ) TECHNICAL SPECIFICATIONS OF EXISTING LIGHTNING ARRESTORS S. No. Description Parameter 1. Type Station class heavy duty zinc oxide gapless 2. Applicable standard IEC / IS:3070 part 3 (Latest) 3. Rated voltage of the arrester KV (rms) Maximum continuous operating KV(rms) Voltage Rated frequency Discharge class III (Three) 6. Nominal discharge current at 8/20 microsecond wave. 10 KA 7. Front of wave protective level with microsecond steep 654 wave at 10KA. KV (peak) 8. Max. switching surge protective level at 1000 Amps 446 crest. KV 9. Power frequency withstand voltage of arrester insulation. a) Dry 460 b) Wet Impulse withstand voltage of arrester insulation. Dry KV (peak) Residual voltage at KV (peak) a) 0.5 P.U. of rated discharge current 485 b) 1.0 P.U. of rated discharge current 525 c) 2.0 P.U. of rated discharge current Impulse current withstand 12.1 High current short duration test value KA Low current long duration test value As per class Virtual duration of rectangular wave 2400 microsecond 12.4 Long duration rating in amperes for 1000 and 2000 µs As per IEC / IS:3070 part Discharge capability of the arrester KJ/KV 5KJ/KV (Minimum) 14.0 Temporary over voltage KV (peak) Withstand capability 0.1 Second Second Second Second 336 Continues Net weight of the arrester ( approx) Kgs < Is the arrester designed to withstand 200 KMPH wind Yes velocity when it is mounted on a 2500mm tall structure Wind velocity the lightning arrester can withstand 300 KMPH (Approx.) without failure 18. Cantilever strength of the complete arrester (min.) 350 Kg 19. Discharge counter and leakage current meter provided. Yes 20. Pressure relief device provided yes 21. Minimum Creepage distance of lightning arrester 6400 mm 22. Weather the lightning arrester assembly is designed to withstand applicable seismic load? Yes 23. Mounting Base Bolts As Shown in drawing 24. Maximum radial distance over which pieces of lightning arrester scatter in the event of its damaged during discharge. Falls within a distance of 1.3 mtrs. from arrester mounting
2 Annexure-II COMPLIANCE FOR BIDDER (Bidder shall mention specifications of quoted product in the table mentioned below): Table-1 S. No. Description Bidders specification for quoted item 1. Type 2. Applicable standard 3. Rated voltage of the arrester KV (rms) 4.1 Maximum continuous operating KV(rms) Voltage 4.2 Rated frequency 5. Discharge class 6. Nominal discharge current at 8/20 microsecond wave. 7. Front of wave protective level with microsecond steep wave at 10KA. KV (peak) 8. Max. switching surge protective level at 1000 Amps crest. KV 9. Power frequency withstand voltage of arrester insulation. a) Dry b) Wet 10. Impulse withstand voltage of arrester insulation. Dry KV (peak) 11. Residual voltage at KV (peak) a) 0.5 P.U. of rated discharge current b) 1.0 P.U. of rated discharge current c) 2.0 P.U. of rated discharge current 12. Impulse current withstand 12.1 High current short duration test value KA 12.2 Low current long duration test value 12.3 Virtual duration of rectangular wave 12.4 Long duration rating in amperes for 1000 and 2000 micro seconds 13.0 Discharge capability of the arrester KJ/KV 14.0 Temporary over voltage KV (peak) Withstand capability 0.1 Second 1.0 Second 10.0 Second Second Continues 15.0 Net weight of the arrester ( approx) Kgs 16.0 Is the arrester designed to withstand 200 KMPH wind velocity when it is mounted on a 2500mm tall structure Wind velocity the lightning arrester can withstand without failure 18. Cantilever strength of the complete arrester (min.) 19. Discharge counter and leakage current meter provided. 20. Pressure relief device provided 21. Minimum Creepage distance of lightning arrester
3 S. No. Description Bidders specification for quoted item 22. Weather the lightning arrester assembly is designed to withstand applicable seismic load? 23. Mounting Base Bolts (To be provided by bidder). If Provided drawing of base is not matching with existing base, then bidder shall arrange the interconnection base, matching with existing foundation base. 24. Maximum radial distance over which pieces of lightning arrester scatter in the event of its damaged during discharge. Other specifications to be complied by bidder: Bidder should mention details of Compliance of the points mentioned item sr. no. i) to vi) in the Table-2 mentioned below: Table-2 S. No. Description of other specification Bidders compliance for specification 1 All routine/ Acceptance / Special Acceptance and Type tests will be carried out as per Latest version and amendments of IS /IEC, which are given at Sr. No. 3 of Tentative QA plan in Annexure-IX. Note: The manufacturer should carry out type test or submit valid test report of type test for lightning arrester being offered for supply. The type test reports should be witness or test should be carried out at NABL accredited/ test laboratory. 2 The offered equipment have to be designed, manufactured and tested as per relevant IS/IEC with latest amendments. 3 Three nos. copies of Instruction Manuals (for operation, maintenance, erection, shipping and storage) in Hindi / English language shall be supplied (Soft and Hard copy), one month prior to the dispatch of the equipment. 4 Has bidder uploaded his offered material`s Dimensional Drawing for Lightning Arrester & Insulating base? 5 Whether the offered drawing of the insulating base is matching with existing insulating base? 6 Has bidder uploaded his offered material`s Dimensional Drawing for Grading Ring? 7 Has bidder uploaded his offered material`s Dimensional Drawing for Terminal connectors? 8 Has bidder uploaded his offered material`s Dimensional Drawing for Surge Monitor cum operation counter & leakage meter? 9 Has bidder uploaded his offered material`s Dimensional Drawing for Name plate details? 10 Has bidder uploaded his offered material`s Dimensional Drawing for Cut way section? 11 Has bidder uploaded his offered material`s Dimensional Drawing for Voltage Time curve? 12 Tentative QA plan is attached in Annexure-IX. However bidder will submit detailed QA plan for approval after PO placement and before manufacturing.
4
5
6
7
8
9
10 Annexure-IX Quality assurance programme Zinc oxide surge arresters, insulating base and surge monitors S. No. Component and operation Characteristics Classification Types of check Quantum of check Reference Documents Format of record Agency Action by NPC 1. Raw materials 1.01 Zinc oxide and other additives 1.02 Aluminum Alloy Chemical analysis 1.03 Copper, Brass, M.S. Stainless steel sheets 1.04 Aluminum Castings for arrester base and monitor 1.05 Cover plate (fabricated hot dip galvanizing) 1. Purity check 2. Moisture check 3. Grain size Critical Chemical Chemical Physical basis (3) samples from lot / ton analysis Critical Chemical basis (1) samples for two tonnes 1. Visual 2. Thickness 3. Formability 1. Dimension 2. Visual 3. Mechanical test 1. Visual 2. Dimension 3. Galvanizing 4. Weight of coating 5. Dip test 1.06 Gasket 1. Dimension 2. Hardness Critical Critical Visual Mechanical Visual Mechanical Visual Chemical basis (1) for every batch of tonne basis( one for every 100 nos.) basis( one for every 100 nos.) 10% PS IS Report report R* IS TR R PS TR R IS-2633 and as per Drawing As per PS and Drg. R TR R TR R
11 1.07 Capacitor used in Surge Monitor 1.08 Ammeter used in Surge Monitor 1.09 End Terminal Connectors 3. Ageing Critical in Lab basis( one for every 100 nos.) 1. Capacitance Critical Electrical 2. Dielectric Critical Electrical basis( one for every 100 nos.) 1. Meter Calibration 2. Surge 1. Visual 2. Dimension 3. Chemical Composition 4. Mechanical test on connectors Critical Electrical Electrical Physical Chemical Chemical Mechanical basis( one for every 100 nos.) Routine 10% basis PS ---- Customer appd. Drawing as per IS TR TR R R R 1.10 Procelain Housing 1. Visual 2. Diemension 3. Electrical withstand test 4. Porosity 5. Temp Cycle Critical Visual Electrical Mechanical 10% IS-3070 Appd. Drag. IS-5621 IS-3070 TR do-
12 S. No. Component and operation Characteristics Classification Types of check Quantum of check Reference Documents Format of record Agency Action by NPC 2. In process Inspection 2.01 Block 1. Dimension 2. Visual 3. 1mA DC check 4. Residual Voltage 5. Energy 6. Long duration 7. Accelerated Ageing 2.02 End fitting assembly with porcelain 2.03 Leak, Evacuation sealing 1. Dimension 2. Visual 1. Sealing Effectiveness Critical Visual Electrical Mechanical Visual 10% One from each lot 5% Routine PS 04 do- As per Drag. TR TR R TR R Critical Mechanical PS TR R
13 S. No. Component and operation Characteristics Classification Types of check Quantum of check Reference Documents Format of record Agency Action by NPC 3 Final Inspection 3.01 Lighting Arresters 1 Routine 1. of Reference Voltage 2. RIV 3. Residual Voltage 4. Leak Critical Electrical Routine As per IEC Latest do- TR R 2 Acceptance 1. of power frequency reference voltage in arrester units 2. Lighting impulse residual voltage test on arrester units 3. RIV on Units 4. Galvanizing 5. Dimension Electrical Mechanical Nearest higher whole no. to the cube Root of LAs LAs Supplied One No. 3 Nos. As per IEC Report HP# 2A Special acceptance test 1. Thermal Stability on Sections 3 Type 1. Dry & Wet insulation withstand test 2. Residual Voltage 3. Current Impulse withstand tests Critical Electrical Same as above As per IEC spec. Electrical As per IEC As per IEC TR HP HP HP
14 4. Operating Duty HP 5. Mechanical s HP on Insulators 6. Porosity s on R Insulators 7. Production of R original Type s Certificates for Pressure Relief 8. Visual Corona R Discharge 9. Long Duration R Current on Surge Monitor 3.02 Surge Monitor 1. Routine and 1. Meter Electrical PS TR R/HP acceptance tests calibration Routine Counter Verification 3.03 Insulating Base 1. Voltage R Withstand 2. Visual Visual 3. Wet Power Voltage Withstand Electrical One per 100 Nos. (*)R - Review of test certificates by bidder and record verification by NPC (#)HP-Hold point tests to be conducted in presence of NPC & clearance shall be obtained before further proceeding.
Quality assurance Test Facilities for Gapless ZnO Surge Arresters in High Voltage Division of CPRI, Bengaluru
Quality assurance Test Facilities for Gapless ZnO Surge Arresters in High Voltage Division of CPRI, Bengaluru Abstract: Surge arrester is one of the important power system network components which is neglected
More informationFigure 1. Storm Trapper H. E. arrester, external mount. Figure 2. Storm Trapper H.E. arrester, metal enclosed. use in Storm Trapper H.E. arresters.
Surge Arresters Storm Trapper H.E. (High Energy) Low-Voltage Distribution-class MoV Surge Arrester Electrical Apparatus 235-16 GEnErAL Cooper Power Systems Storm Trapper H.E. (High Energy), lowvoltage
More informationCentral Power Research Institute, Medipally PO, Uppal, Hyderabad, Telangana. Discipline Electrical Testing Issue Date
Last Amended on 31.07.2015 Page 1 of 11 I. SWITCHGEAR EQUIPMENT 1. High Voltage switchgear & control gear and AB switches Ratings upto 1200 kv system Switching Impulse Voltage (Dry & Wet) Power Frequency
More informationEach VariSTAR Type AZU arrester must pass the following production tests: 100% Physical Inspection 100% Leakage Current Test 100% RIV Test
Surge Arresters VariSTAR Type AZU Heavy-duty Distribution Class Under-oil MOV Arrester Electrical Apparatus 235-64 GENERAL The Cooper Power Systems VariSTAR Type AZU under-oil MOV arrester is designed
More informationTechnical specifications for 5 ka, normal-duty distribution 4.5 kv and 5
Surge Arresters Technical Data TD235028EN Supersedes January 2012 (TD-231) COOPER POWER SERIES Technical specifications for 5 ka, normal-duty distribution 4.5 kv and 5 kv VariSTAR Mov disks Ø32.7 ±0.28
More information3a. IEM Indoor Metal Clad Medium Voltage Switchgear 25KV a. Section INDOOR METAL CLAD MEDIUM VOLTAGE SWTICHGEAR (Std.
3a. IEM Indoor Metal Clad Medium Voltage Switchgear 25KV 16346-1 3a. Section 16346 INDOOR METAL CLAD MEDIUM VOLTAGE SWTICHGEAR (Std. Relays) Part 1 General 1.1 CONDITIONS AND REQUIREMENTS: A. Refer to
More informationElastimold Molded Vacuum Recloser - MVR
Subject: Elastimold Recloser Technical Specification Date: 4/24/12 File: MVR-RS-0412 Page: 1 of 6 1.0 SCOPE Elastimold Molded Vacuum Recloser - MVR 1.1 This specification covers electrical and mechanical
More informationCOOPER POWER. UltraSIL polymer-housed VariSTAR IEEE surge arresters; normal-duty (5 ka), heavyduty, and riser pole (10 ka) for MV systems to 36 kv
Surge Arresters Catalog Data CA235005EN Supersedes March 2015 COOPER POWER SERIES UltraSIL polymer-housed VariSTAR IEEE surge arresters; normal-duty (5 ka), heavyduty, and riser pole (10 ka) for MV systems
More informationDynaVar SURGE ARRESTERS
70 DynaVar SURGE ARRESTERS IEC 5KA, 10KA Class 1 & 2 and IEEE Distribution & Riser Pole Surge Arresters Experience & Reliability Page 1 August 2012 Table of Contents Page Warranty...70-2 Introduction...70-3
More information35 kv Class M.O.V.E. DirectConnect elbow arrester
Surge Arresters Catalog Data CA3506EN Effective February 017 Supersedes November 015 COOPER POWER SERIES 35 kv Class M.O.V.E. DirectConnect elbow arrester General Eaton's Cooper Power series M.O.V.E. DirectConnect
More informationExternally Gapped Line Arresters Smart Solution for Stable Power Supply
Smart Solution for Stable Power Supply Metal-oxide surge arresters with external series gaps improve the reliability of transmission systems, and help eliminate not only lightning damages of transmission
More informationExternally Gapped Line Arresters Smart Solution for Stable Power Supply
Smart Solution for Stable Power Supply Metal-oxide surge arresters with external series gaps improve the reliability of transmission systems, and help eliminate not only lightning damages of transmission
More informationVariSTAR AZE Station Surge Arresters
VariSTAR AZE Station Surge Arresters Metal Oxide Varistor Technology for Systems through 345kV Aluminum Alloy Line Terminal Accommodates up to 3/4 inch copper/aluminum conductor and NEMA standard connectors.
More informationNeXLev Product Specification TB2144
NeXLev Product Specification TB2144 Revision B Specification Revision Status Revision SCR No. Description Initial Date - S0161 New Release DM 4/5/2006 A S1357 Update copper material callout, DM 8/31/09
More informationThis annex is valid from: to Replaces annex dated: Location(s) where activities are performed under accreditation
Location(s) where activities are performed under accreditation Head Office Utrechtseweg 310, Building no. R11 6812 AR Arnhem The Netherlands Location Abbreviation/ location code Utrechtseweg 310, Building
More informationApplication Considerations for Gapped Silicon-Carbide Arresters Currently Installed on Utility High Voltage Installations
Application Considerations for Gapped Silicon-Carbide Arresters Currently Installed on Utility High Voltage Installations Dennis W. Lenk, Fellow, IEEE Abstract Utilities have expressed concern recently
More informationPRODUCT SPECIFICATION
1.25 mm pitch SMT Wire to Board Connector 1 of 7 A 1.0 SCOPE This specification covers performance, tests and quality requirements for 1.25 mm pitch Wire to Board DIP & SMT Type of 10114826~10114831 Series.
More informationSPECIAL SPECIFICATION 1864 Pole Mounted Cabinet
1993 Specifications CSJ s 0924-06-221,etc. & 0924-06-223 SPECIAL SPECIFICATION 1864 Pole Mounted Cabinet 1. Description. This specification describes the minimum acceptable requirements for a weatherproof
More informationProduct Specification
Product Specification PR041-01 Revision A0 (Date 4-3-2017) Stewart Connector 11118 Susquehanna Trail South Glen Rock, Pa. 17327-9199 Ph: (717) 235-7512 Fax: (717) 235-4675 Product Specification PR0410-01
More informationRE17LAMW on-delay timing relay - 1 s..100 h V AC/DC - solid state output
Characteristics on-delay timing relay - 1 s..100 h - 24..240 V AC/DC - solid state output Complementary Control type Voltage range Main Range of product Product or component type Discrete output type Width
More informationPRODUCT SPECIFCATION GS MINI-SAS HD External Cable to Board Connector System. 1 of 14 F. Roger Cheng TYPE NUMBER
1 of 14 F TABLE OF CONTENTS 1.0 OBJECTIVE... 3 2.0 SCOPE... 3 3.0 APPLICABLE DOCUMENTS... 3 3.1 FCI SPECIFICATIONS... 3 3.2 OTHER STANDARDS AND SPECIFICATIONS... 3 3.3 FCI PRODUCT QUALIFICATION TEST REPORTS...
More informationSpecifications. S&C Loadbuster Disconnect Switches Outdoor Distribution (14.4 kv through 34.5 kv)
Outdoor Distribution ( kv through 34.5 kv) Specifications Conditions of Sale STANDARD: Seller s standard conditions of sale set forth in Price Sheet 150 apply. SPECIAL TO THIS PRODUCT: INCLUSIONS: All
More informationOVP2. The Over-Voltage Protector 2 (OVP2) Technical Literature
The Over-Voltage Protector 2 (OVP2) Technical Literature INTRODUCTION The Over-Voltage Protector (OVP) design has been established since 1999 as the premier explosion-proof (Division 1) protection device
More informationMini PCI Express Card Socket
Mini PCI Express Card Socket Document No: Page: 1 of 4 1. Scope This specification covers the material and performance requirements for the Mini PCI Express Card Socket series. 2. Applicable documents
More informationPlug and Operate Transformer Technology
Plug and Operate Transformer Technology Deepal Shah PFISTERER deepal.shah@pfisterer.com by and Andre Goessler PFISTERER andre.goessler@pfisterer.com 1 THE POWER CONNECTION We have always worked closely
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60099-5 Edition 3.0 2018-01 colour inside Surge arresters Part 5: Selection and application recommendations INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 29.120.50; 29.240.10
More informationHan PCB termination. Han-Fast Lock PCB adapter for Han DD PCB adapter for Han DDD module
Han termination Contents Page Han-Fast Lock... 20.11 adapter for Han DD... 20.13 adapter for Han DDD module... 20.16 adapter for Han 40 A Axial module... 20.18 adapter for Han E... 20.20 adapter for Han
More informationRE48ATM12MW on-delay timing relay s..300 h V AC - 2 OC
Characteristics on-delay timing relay - 0.02 s..300 h - 24..240 V AC - 2 OC Complementary Product front plate size Control type Housing material Main Range of product Product or component type Electrical
More informationRE48ATM12MW on-delay timing relay s..300 h V AC - 2 OC
Characteristics on-delay timing relay - 0.02 s..300 h - 24..240 V AC - 2 OC Product availability : Stock - Normally stocked in distribution facility Price* : 73.00 USD Main Range of product Product or
More informationRole of Surge Arrestors in Electrical Power Systems
International Journal of Advances in Electrical and Electronics Engineering 1 Available online at www.ijaeee.com & www.sestindia.org/volume-ijaeee/ ISSN: 2319-1112 Role of Surge Arrestors in Electrical
More informationPRODUCT SPECIFICATION. This specification defines the detailed requirements for the Minitek Pwr3.0 wire to wire and wire to board connectors.
s-12-1177*1.0 SCOPE 1 of 8 D This specification defines the detailed requirements for the Minitek Pwr3.0 wire to wire and wire to board connectors. 2.0 APPLICABLE DOCUMENTS The following documents, of
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR GROUNDING, BONDING, LIGHTNING PROTECTION AND SURGE PROTECTION FOR INTELLIGENT TRANSPORTATION SYSTEM EQUIPMENT ITS:CLC 1 of 5 APPR:LWB:DBP:07-31-13
More information2701DLA 25kV Class DEADBREAK to LOADBREAK ADAPTER
R&D Center 497 Schooley s Mountain Road Hackettstown, NJ 07840-3906 Tele: 908-852-1122 Fax: 908-813-2091 TEST REPORT NUMBER: 370-17-11353 rev a DATE: 12/19/2011 REPORT OF TEST ON 2701DLA 25kV Class DEADBREAK
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR MICROWAVE VEHICLE DETECTION SYSTEM
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR MICROWAVE VEHICLE DETECTION SYSTEM ITS:CLC 1 of 6 APPR:LWB:DBP:07-31-13 FHWA:APPR:09-23-13 a. Description. This work consists of one or more
More informationRE17LAMW on-delay timing relay - 1 s..100 h V AC/ DC - solid state output
Characteristics on-delay timing relay - 1 s..100 h - 24..240 V AC/ DC - solid state output Main Range of product Product or component type Discrete output type Width Component name Time delay type Time
More informationSPECIFICATION AND PERFORMANCE CHARACTERISTICS OF DVI MALE AND FEMALE CONNECTOR SERIES
SPECIFICATION AND PERFORMANCE CHARACTERISTICS OF DVI MALE AND FEMALE CONNECTOR SERIES CIRCUIT ASSEMBLY CORP. 18 THOMAS STREET, IRVINE, CA 92618-2777 Page No. 1 CONTENTS CLAUSE PAGE 1.0 SCOPE.. 3 2.0 APPLICABLE
More informationPRODUCT SPECIFICATION
SIM Card Connector, Hinged Type, 8 Pin, SMT, 1.50mm Profile. Page 1 SIM Card Connector, Hinged Type, 8 Pin, SMT, 1.50mm Profile. Page 2 1.0 SCOPE. This specification covers performance, tests and quality
More informationFerraz Shawmut TPMOV Principles and Operation
TPMOV Origin Due to recent changes in the Underwriters Laboratories Standard for Safety for Surge Protective Devices UL 1449 additional requirements have been instituted to maintain listings of Surge Protective
More informationRE17LCBM off-delay timing relay - control - 1 s..100 h V - solid state output
Characteristics off-delay timing relay - control - 1 s..100 h - 24..240 V - solid state output Main Range of product Product or component type Discrete output type Width Component name Time delay type
More informationRE11RAMU on-delay timing relay - 1 s..100 h V AC - 1 OC
Characteristics on-delay timing relay - 1 s..100 h - 24..240 V AC - 1 OC Complementary Contacts material Width pitch dimension Control type Voltage range Connections - terminals Housing material Main Range
More informationAMPMODU* MOD I Interconnection System
Product Specification AMPMODU* MOD I Interconnection System 03 JUN 2013 Rev E All Paragraphs Revised 1. SCOPE This specification covers performance and test requirements for the AMPMODU MOD I Interconnection
More informationFEB2018 Rev H
Product Specification 108-32122 14FEB2018 Rev H PV Edge Solar Junction Box 1. SCOPE 1.1. Content This specification covers the performance, tests and quality standards for the SOLARLOK* PV Edge Solar Junction
More informationPRODUCT SPECIFICATION
1.0 SCOPE DDR4 DIMM SOCKET This Product Specification covers the 0.85mm centerline gold plated DDR4 DIMM edge card connector for 1.40 ± 0.10 thick memory modules..0 PRODUCT DESCRIPTION.1 PRODUCT NAME AND
More informationRL Line/Load Reactors
RL Line/Load Reactors Selection Table, Technical Details & Product Application Guide MTE HARMONIC COMPENSATED LINE/LOAD REACTORS help keep your equipment running longer by absorbing many of the power line
More informationProduct Specification AMP Connector USB Consortium, Plug & Receptacle. Lead Free Version
Product Specification 108-60034 AMP Connector USB Consortium, Plug & Receptacle Lead Free Version 1. Scope: 1.1 Contents: This specification covers the requirements for product performance, test methods
More informationAug04 Rev D EC
Product Specification 108-1163 18Aug04 Rev D EC 0990-1127-04 Modular Plugs, Thru-Hole and Surface Mount Jacks, Data and Telephone, PCB Mounted 1. SCOPE 1.1. Content This specification covers the performance,
More informationXB4BK123B5. Product data sheet Characteristics. Complete illuminated selector switch. position stay put 1NO+1NC 24V. Main.
Characteristics green complete illuminated selector switch Ø22 2- position stay put 1NO+1NC 24V Main Range of product Product or component type Device short name Bezel material Fixing collar material Mounting
More informationMETAL-OXIDE SURGE ARRESTER PROTECTION OF DISTRIBUTION SYSTEMS
POWER SYSTEMS, INC. METAL-OXIDE SURGE ARRESTER PROTECTION OF DISTRIBUTION SYSTEMS Customer Service 210 N. Allen St. Centralia, MO 65240 Phone 573-682-5521 Fax 573-682-8714 NOTE: Because Hubbell has a policy
More informationRE Product data sheet Characteristics. universal plug-in timing relay - flashing s..60 mn V AC - 2 OC. Main.
Characteristics universal plug-in timing relay - flashing - 0.1 s..60 mn - 24..240 V AC - 2 OC Main Range of product Product or component type Discrete output type Contacts type and composition Width pitch
More informationFigure 1. ELSP Current-Limiting Backup Fuse. INSTALLATION
Fusing Equipment Current-Limiting Backup Fuse Electrical Apparatus - GENERAL The Cooper Power Systems Current-limiting Backup Fuse is used in series with low current primary protection devices such as
More informationPERFORMANCE SPECIFICATION
INCH-POUND MIL-PRF-6106/13F 17 November 2011 SUPERSEDING MIL-PRF-6106/13E 10 November 2000 PERFORMANCE SPECIFICATION RELAY, ELECTROMAGNETIC, 25 AMPERE, 3PST, NO, WITH 2 AMPERE 1PDT AUXILIARY CONTACTS,
More informationTT-ST-M-2-PE-24DC. Extract from the online catalog. Order No.:
Extract from the online catalog TT-ST-M-2-PE-24DC Order No.: 2858904 TERMITRAB, spring-cage modular terminal block with integrated surge protection and disconnect knives, for assembly on NS 35/7.5, voltage
More informationSpecification Voltage Limiting Device
Engineering Specification Electrical Networks L1-CHE-SPE-152 Specification Voltage Limiting Device Version: 1 Issued: 20 th April 2018 Owner: Chief Engineer Approved By: Andrew Russack Head of Engineering,
More information/June/2014 Rev C
Qualification Test Report 501-93032 18/June/2014 Rev C AMP-TWIST Series Jacks for Class EA systems 1. INTRODUCTION 1.1 Purpose Qualification testing on AMP-TWIST* Series Jacks for Class EA Systems, to
More informationEMOSAFE EN-100 Network Isolators for PCB assembly
ENGLISH EMOSAFE EN-100 Network Isolators for PCB assembly Product Datasheet 1 FEATURES AND ADVANTAGES Suitable for PCB assembly: pluggable or solderable Ultra-compact Conforms to IEC 60601-1 10/100/1000
More informationSECTION SURGE PROTECTION DEVICES. A. Section includes Surge Protection Devices for low-voltage power, control, and communication equipment.
SECTION 26 43 00 SURGE PROTECTION DEVICES PART 1 - GENERAL 1.1 SUMMARY A. Section includes Surge Protection Devices for low-voltage power, control, and communication equipment. 1.2 DEFINITIONS A. ATS:
More informationAC Capacitors for HID Lighting Applications
GTC 002 2011 AC Capacitors for HID Lighting Applications Proven EIA-456 Compliant 60,000 Hour Reliability Industry Standard Genteq Capacitors 1946 West Cook Road, Fort Wayne, Indiana 46818 USA Phone: (260)
More informationRelion 611 series. 611 series Type Test Certificate
Relion 611 series 611 series Document ID: 1MRS757466 Issued: 2016-02-22 Revision: B Product version: 2.0 Copyright 2016 ABB. All rights reserved Table of contents Table of contents Section 1 Section
More informationOvervoltage Protection Devices
Siemens AG 2010 Overvoltage Protection Devices /2 Introduction /3 Lightning Arresters, Type 1 /5 Combination Surge Arresters, Type 1 and Type 2 /7 Surge Arresters, Type 2 /11 Surge Arresters, Type 3 /12
More informationMSP Reliability White Paper Bourns, Inc. Hans-Wolfgang Oertel Vice President of Technology
Reliable Electronic Solutions MSP Reliability White Paper Bourns, Inc. Hans-Wolfgang Oertel Vice President of Technology Dehn Incorporated Richard Chadwick Vice President of Engineering February 2000 OVERVIEW
More informationUltraSIL polymer-housed VariSTAR surge arresters 5 ka and 10 ka Class 1 IEC for MV systems to 36 kv
Surge s Catalog Data CA235029EN Effective February 2016 Supersedes I235-35 August 2014 COOPER POWER SERIES UltraSIL polymer-housed VariSTAR surge arresters 5 ka and 10 ka Class 1 IEC 60099-4 for MV systems
More informationRE22R2QTMR Star-Delta Timing Relay s 300h V AC/DC - 2C/O
Characteristics StarDelta Timing Relay 0.05s 300h 24 240V AC/DC 2C/O Main Range of product Product or component type Discrete output type Device short name Nominal output current Zelio Time Modular timing
More informationRE Product data sheet Characteristics. time delay relay for star-delta starter ms - 230/380 V AC - 1 contact. Main.
Characteristics time delay relay for star-delta starter - 20..140 ms - 230/380 V AC - 1 contact Main Range of product Product or component type Contacts type and composition Component name Time delay type
More informationCERTIFIED TEST REPORT
CP No.: CP1120 Rev. 1 Page: 1 of 24 CERTIFIED TEST REPORT Cooper Power Systems 15 kv Class 600 Amp CLĒĒR TM LOADBREAK SEPARABLE CONNECTOR SYSTEM REV. 1 DATE September 1, 2011 ORIGINAL REPORT DATE: July
More informationOvervoltage Protection Devices
Overvoltage Protection Devices /2 Introduction /3 5SD7 lightning arresters, type 1 /5 5SD7 combination surge arresters, type 1 and type 2 /7 5SD7 surge arresters, type 2 /10 5SD7 surge arresters, type
More informationData sheet ACT20P ACT20P-CMT-10-AO-RC-S. Phone: Fax: Web: - [!
-CMT-10-AO-RC-S [!-] General ordering data Type -CMT-10-AO-RC-S Order No. 1510470000 Version Current-measuring transducer GTIN (EAN) 4050118319583 Qty. 1 pc(s). -CMT-10-AO-RC-S Technical data Dimensions
More informationThe Rosemount 356 Nuclear Connector
Product Data Sheet 00813-0200-4856, Rev AE March 2013 Rosemount 356 The Rosemount 356 Nuclear Connector Easy-to-install connector for use outside containment Die cast zinc or stainless steel connector
More informationfor the protection of gas-insulated metal-enclosed switchgear against lightning and switching overvoltages
GAS-INSULATED METAL-ENCLOSED SURGE ARRESTERS (GIS-ARRESTERS) for the protection of gas-insulated metal-enclosed switchgear against lightning and switching overvoltages GIS-Arresters from Siemens GIS arresters
More informationPDS: Rev :A STATUS:Released Printed: Jan 04, 2012
of 2 A.0 Objective This specification defines the performance, test, quality and reliability requirements of the USB3.0 Standard- A Receptacle. 2.0 Scope This specification is applicable to the termination
More informationSCT500D Twin SMD Ceramic PTC Thermistor
Desciption The component consists of two high-performance ceramic PTCs mounted in a lead-frame for (SMD) direct soldering onto a printed-circuit board (PCB) or substrate. The ceramic PTCs are soldered
More informationDatasheet - CSS 11-30S-D-M-ST
12.02.2013-18:42:30h Datasheet - CSS 11-30S-D-M-ST Safety sensors / CSS 30S Preferred typ Stainless steel enclosure Max. 31 sensors can be wired in series. Connector M12, 8-pole Ø M30 High repeat accuracy
More informationPRODUCT SPECIFICATION
SIM Card Connector, Hinged Type, 6 Pin, SMT, 1.85mm Profile. Page 1 SIM Card Connector, Hinged Type, 6 Pin, SMT, 1.85mm Profile. Page 2 1.0 SCOPE. This specification covers performance, tests and quality
More informationCROWN LINE Power Bus Bar Distribution System
COWN LINE Power Bus Bar Distribution System COWN LINE Power Bus Bar Distribution System The pluggable bus bar system Currents up to 300 Amps Up to 2 meters in length Pluggable breakers VDE finger proof
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. Power Connectors FEATURES AND SPECIFICATIONS Features and Benefits Positive
More informationPRODUCT SPECIFICATION
RECEPTACLE.0 SCOPE This Product Specification covers the performance requirements of the Serial Attach SCSI / High Speed Serialized host receptacle connector. 2.0 PRODUCT DESCRIPTION 2. PRODUCT NAME AND
More informationRE7RB13MW adjustable off-delay timing relay s V AC DC - 2OC
Characteristics adjustable off-delay timing relay - 0.05..1 s - 240 V AC DC - 2OC Main Range of product Product or component type Contacts type and composition Component name Time delay type Time delay
More informationFile E Project 12SC February 9, 2013 REPORT. Component - Protectors, Low-voltage Solid-state Overcurrent
File E211395 Project 12SC04547 February 9, 2013 REPORT On Component - Protectors, Low-voltage Solid-state Overcurrent Copyright 2013 UL LLC MAXIM INTEGRATED PRODUCTS AUSTIN, TX 78729 UL LLC authorizes
More informationSpecifications. S&C Regulator Bypass Switches Type XL (Sequenced) and Type NL (Nonsequenced) Outdoor Distribution (14.
Type XL (Sequenced) and Type NL (Nonsequenced) Outdoor Distribution (14.4 kv and 25 kv) Specifications Conditions of Sale STANDARD: The seller s standard conditions of sale set forth in Price Sheet 150
More informationRE22R2AMR On-delay Timing Relay s 300h V AC/DC - 2C/O
Characteristics Ondelay Timing Relay 0.05s 300h 24 240V AC/DC 2C/O Main Range of product Product or component type Discrete output type Device short name Nominal output current Zelio Time Modular timing
More informationSpecif ications. S&C Alduti-Rupter Switches Outdoor Distribution (14.4 kv through 69 kv)
S&C Alduti-Rupter Switches Outdoor Distribution ( through 69 ) Specif ications Conditions of Sale STANDARD: The seller s standard conditions of sale set forth in Price Sheet apply, except as modified under
More informationQUINT-BUFFER/24DC/24DC/40
Buffer module Data sheet 105496_en_01 PHOENIX CONTACT 2013-11-01 1 Description The QUINT BUFFER buffer module combines the electronic switchover unit and power storage in the same housing. The buffer module
More informationSECTION TRANSIENT VOLTAGE SUPPRESSION FOR LOW-VOLTAGE ELECTRICAL POWER CIRCUITS
SECTION 264313 - TRANSIENT VOLTAGE SUPPRESSION FOR LOW-VOLTAGE ELECTRICAL POWER CIRCUITS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and
More informationThe Solid-State Decoupler (SSD)
The Solid-State Decoupler (SSD) Installation Instructions Introduction The Solid-State Decoupler (SSD) is a solid-state DC isolation/ac grounding (i.e., coupling) device design ed for use in conjunction
More informationRE22R1QMQ star-delta timing relay - 230VAC/440VAC - 1 C/ O
Characteristics star-delta timing relay - 230VAC/440VAC - 1 C/ O Main Range of product Product or component type Discrete output type Device short name Nominal output current Zelio Time Modular timing
More informationNEW surge protective devices
NEW surge protective devices For use in low-voltage systems For overhead power lines and buildings Made in EU ABOUT COMPANY INTRODUCTION Company ELEKTROMEHANIKA & BB d.o.o. was established from recent
More informationSurge Protection Devices Ex9UE2
Surge Protection Devices Ex9UE2 Surge Protection Devices Type 2 (Class II, T2, C) Tested according to EN 61643-11 Maximum continuous operational voltage U c from 275 V up to 440 V AC Versions with 1+0,
More informationPT 3-PB-ST. Extract from the online catalog. Order No.:
Extract from the online catalog PT 3-PB-ST Order No.: 2858030 Surge protection plug for the base element, normal mode voltage coarse and fine protection for two floating signal wires in IT, common mode
More informationMULTI-POLE PHOTOVOLTAIC SYSTEMS. COMPACT and MODULAR Housing
MULTI-POLE Lightning Current and Surge Arresters for PHOTOVOLTAIC SYSTEMS Class I / (B+C) and Class II / (C) COMPACT and MODULAR Housing 44 PV ISPRO BS(R) 12,5 The PV ISPRO BS(R) 12,5 series of over voltage
More informationCOOPER POWER SERIES. Fusing Equipment Catalog Data CA132064EN. Effective February 2018 Supersedes January 2014 (240-50)
Fusing Equipment Catalog Data CA132064EN Supersedes January 2014 (240-50) COOPER POWER SERIES Table of contents Attention....3 Eaton is in the process of updating part numbers and technical data due to
More informationPRODUCT SPECIFICATION
1.0 SCOPE This Product Specification covers the 3.00 mm (.118 inch) centerline (pitch) square pin headers when mated with either printed circuit board (PCB) connector or connectors terminated with 20 to
More informationADVANCED SYSTEM DESIGN PRODUCT SPECIFICATIONS FFT*-*P Full Feature Equalizable Taps
FEATURES OF FFT*-*P TAP SERIES: ABILITY TO ACCEPT PLUG-IN MODULES FOR IMPROVED RETURN PATH PERFORMANCE: CABLE EQUALIZATION RETURN PATH ATTENUATION CABLE SIMULATION AUTO-SEIZE F-CONNECTORS 6kV FEEDERLINE
More informationMini PCI Express & msata Connector
09.Mar.2012 Rev. C Mini PCI Express & msata Connector 1 Scope: 1.1 Contents This specification covers the requirements for product performance, test methods and quality assurance provisions of MINI PCI
More informationOvervoltage Protection Devices
Siemens AG 2013 Overvoltage Protection Devices /2 Introduction /3 5SD7 lightning arresters, type 1 /5 5SD7 combination surge arresters, type 1 and type 2 /7 5SD7 surge arresters, type 2 /10 5SD7 surge
More informationSafety wherever needed
Safety wherever needed Low Voltage Surge Arrestors Uninsulated version Isolated version Rope-throwing-off-function MM: Bild angeben Content 280 Technical data see page 281 System The Low Voltage Surge
More informationTesting Instruments Manufactured by
Circuit Breaker Dynamic Contact Resistance Meter HISAC Ultima Circuit Breaker Dynamic Test Set with up to Six Channel Dynamic Contact Resistance Meter 24 Binary Channels (4 Main + 4 PIR per Pole, 3 Poles
More information02/11/2015
35 mm - 1 Relay 8A OUR1 Part number 88867105 Multi-function or mono-function Multi-range Multi-voltage Relay output 1 or 2 : 8 A - 250 V (10 A UL) LED status indicator Option of connecting an external
More informationENGR. MARITES R. PANGILINAN, P.E.E.
ENGR. MARITES R. PANGILINAN, P.E.E. WHAT IS LOW VOLTAGE INSULATION COORDINATION AND WHY IT IS IMPORTANT WHERE DO SURGES COME FROM HOW DO SPDs WORK/TYPE OF SPDs SPD SPECIFICATIONS SPD COORDINATION /CASCADING
More informationPHOENIX CONTACT - 06/2007. DANGER OF EXPLOSION! Remove an item only when it is not connected to power or if it is located in the non-explosive area.
Primary switched power supply, 3-phase, output current: 40 A INTERFACE Data Sheet 102782_01_en PHOENIX CONTACT - 06/2007 Description TRIO POWER is the rail mountable 24 V power supply unit with basic functions.
More information/June/2013 Rev B
Qualification Test Report 501-93016 14/June/2013 Rev B AMP-TWIST* 6S Series SL Jack 1. INTRODUCTION 1.1 Purpose Testing were performed on AMP-TWIST* 6S Series SL Jack, to determine its conformance to the
More informationJV SERIES 1 POLE 5 A (MEDIUM LOAD CONTROL) POWER RELAY. RoHS compliant
POWER RELAY 1 POLE 5 A (MEDIUM LOAD CONTROL) JV SERIES RoHS compliant FEATURES UL, CSA, VDE, SEMKO, CQC recognized UL class B (130 C) insulation Low profile and space saving Height: 12.5 mm Mounting space:
More information