SteelConnect Access Point Hardware Guide. June 2016

Transcription

1 SteelConnect Access Point Hardware Guide June 2016

2 2016 Riverbed Technology, Inc. All rights reserved. Riverbed and any Riverbed product or service name or logo used herein are trademarks of Riverbed. All other trademarks used herein belong to their respective owners. The trademarks and logos displayed herein cannot be used without the prior written consent of Riverbed or their respective owners. Akamai and the Akamai wave logo are registered trademarks of Akamai Technologies, Inc. SureRoute is a service mark of Akamai. Apple and Mac are registered trademarks of Apple, Incorporated in the United States and in other countries. Cisco is a registered trademark of Cisco Systems, Inc. and its affiliates in the United States and in other countries. EMC, Symmetrix, and SRDF are registered trademarks of EMC Corporation and its affiliates in the United States and in other countries. IBM, iseries, and AS/400 are registered trademarks of IBM Corporation and its affiliates in the United States and in other countries. Juniper Networks and Junos are registered trademarks of Juniper Networks, Incorporated in the United States and other countries. Linux is a trademark of Linus Torvalds in the United States and in other countries. Microsoft, Windows, Vista, Outlook, and Internet Explorer are trademarks or registered trademarks of Microsoft Corporation in the United States and in other countries. Oracle and JInitiator are trademarks or registered trademarks of Oracle Corporation in the United States and in other countries. UNIX is a registered trademark in the United States and in other countries, exclusively licensed through X/ Open Company, Ltd. VMware, ESX, ESXi are trademarks or registered trademarks of VMware, Inc. in the United States and in other countries. This product includes Windows Azure Linux Agent developed by the Microsoft Corporation ( Copyright 2012 Microsoft Corporation. This product includes software developed by the University of California, Berkeley (and its contributors), EMC, and Comtech AHA Corporation. This product is derived from the RSA Data Security, Inc. MD5 Message-Digest Algorithm. The SteelHead Mobile Controller (virtual edition) includes VMware Tools. Portions Copyright VMware, Inc. All Rights Reserved. NetApp Manageability Software Development Kit (NM SDK), including any third-party software available for review with such SDK which can be found at and are included in a NOTICES file included within the downloaded files. For a list of open source software (including libraries) used in the development of this software along with associated copyright and license agreements, see the Riverbed Support site at https//support.riverbed.com. This documentation is furnished AS IS and is subject to change without notice and should not be construed as a commitment by Riverbed. This documentation may not be copied, modified or distributed without the express authorization of Riverbed and may be used only in connection with Riverbed products and services. Use, duplication, reproduction, release, modification, disclosure or transfer of this documentation is restricted in accordance with the Federal Acquisition Regulations as applied to civilian agencies and the Defense Federal Acquisition Regulation Supplement as applied to military agencies. This documentation qualifies as commercial computer software documentation and any use by the government shall be governed solely by these terms. All other use is prohibited. Riverbed assumes no responsibility or liability for any errors or inaccuracies that may appear in this documentation. Riverbed Technology 680 Folsom Street San Francisco, CA Phone: Fax: Web: Part Number

3 Contents Welcome... 5 About This Guide... 5 Documentation and Release Notes... 5 Contacting Riverbed SteelConnect Overview... 7 SteelConnect Access Point Appliances... 7 SteelConnect SDI-AP5R... 8 SteelConnect Access Point LEDs Mounting the SteelConnect Access Point Appliances Site Preparations or Considerations Safety Information Environmental Considerations Mounting the SDI-AP3 and SDI-AP Installing the SDI-AP5R Wall Mounting the SDI-AP5R Pole Mounting the SDI-AP5R Connecting Power Connecting to the Network Connector Requirements A - Specifications SDI-AP3 Specifications SDI-AP5 Specifications SDI-AP5R Specifications SteelConnect Access Point Hardware Guide 3

4 Contents 4 SteelConnect Access Point Hardware Guide

5 Welcome About This Guide This guide describes the SteelConnect access points and provides information you need to install the hardware. This guide is written for administrators responsible for SteelConnect hardware installation and includes information relevant to the following products: SteelConnect SDI-AP3 SteelConnect SDI-AP5 SteelConnect SDI-AP5R Documentation and Release Notes To obtain the most current version of all Riverbed documentation, go to the Riverbed Support site at The Riverbed Knowledge Base contains any known issues, how-to documents, system requirements, and common error messages. You can browse titles or search for keywords and strings. To access the Riverbed Knowledge Base, log in to the Riverbed Support site at Each software release includes release notes. The release notes list new features, known issues, and fixed problems. To see the most current version of the release notes, click the version number in the lower-left corner of SCM. We recommend taking a look at the release notes before you begin using a new version of SCM. Contacting Riverbed Technical support - Problems installing, using, or replacing Riverbed products? Contact Riverbed Support or your channel partner who provides support. To contact Riverbed Support, open a trouble ticket by calling RVBD-TAC ( ) in the United States and Canada or outside the United States. You can also go to Professional services - Need help with planning a migration or implementing a custom design solution? Contact Riverbed Professional Services. proserve@riverbed.com or go to Documentation - Have questions about Riverbed s documentation? Send your comments to techpubs@riverbed.com. SteelConnect Access Point Hardware Guide 5

6 Welcome Contacting Riverbed 6 SteelConnect Access Point Hardware Guide

7 1 SteelConnect Overview The SteelConnect access point (AP) appliances provide enterprise-grade mobility and WiFi for guests, employees, and internet-enabled devices across all locations. Smart roaming streamlines connectivity handover between access points and sites and user-based network access control secures bring-yourown-device (BYOD) environments. The SteelConnect access point appliances consist of the following products: SteelConnect SDI-AP3 SteelConnect SDI-AP5 SteelConnect SDI-AP5R This overview provides a description of the SteelConnect appliances and includes the following sections: SteelConnect Access Point Appliances on page 7 SteelConnect SDI-AP5R on page 8 SteelConnect Access Point Appliances The access point appliances can easily set up an enterprise-class multisite WiFi network for visitors, employees, and the Internet of Things. Organizations have to assign users to a virtual network zone only once. From then on, these virtual zones automatically follow their users across all of your locations, regardless which device is used. SteelConnect SDI-AP3 and SDI-AP5 are indoor appliances, whereas the SteelConnect SDI-AP5R can be used outdoors. Figure 1-1. SteelConnect SDI-AP3 and SDI-AP5 SteelConnect Access Point Hardware Guide 7

8 SteelConnect Overview SteelConnect SDI-AP5R The following items can be found on the bottom panel of the appliance: A reset button resets the appliance to its factory state. Press the button for 10 seconds. After releasing the button all five LEDs flash and the appliance resets to the factory default state. 1-GbE Ethernet port (RJ45) for the PoE DC power port SteelConnect SDI-AP5R The SteelConnect SDI-AP5R is an outdoor access point appliance that can easily set up an enterpriseclass multisite WiFi network for visitors, employees, and the Internet of Things. Organizations have to assign users to a virtual network zone only once. From then on, these virtual zones automatically follow their users across all of your locations, regardless which device is used. Figure 1-2. SteelConnect SDI-AP5R LEDs SteelConnect Access Point LEDs The AP3 and AP5 LEDs are internal and can be seen only when lit and shining through the encasement. LEDs turn off when the AP enters normal operation mode. LED Color Green Orange Definition Power Ethernet 8 SteelConnect Access Point Hardware Guide

9 SteelConnect Access Point LEDs SteelConnect Overview The AP5R LEDs are on the side of the appliance. Figure 1-3. SteelConnect SDI-AP5R LEDs LED Color Definition 5GHz Green Power on 2.4GHz Orange Ethernet LAN2 Green Power on LAN1 Green Power on Power Green Power on SteelConnect Access Point Hardware Guide 9

10 SteelConnect Overview SteelConnect Access Point LEDs 10 SteelConnect Access Point Hardware Guide

11 2 Mounting the SteelConnect Access Point Appliances This chapter describes how to install or mount the access point appliances and discusses the following topics: Site Preparations or Considerations on page 11 Mounting the SDI-AP3 and SDI-AP5 on page 12 Installing the SDI-AP5R on page 13 Connecting Power on page 17 Connecting to the Network on page 17 Connector Requirements on page 17 Site Preparations or Considerations Safety Information on page 11 Environmental Considerations on page 12 Wall Mounting the SDI-AP5R on page 13 Pole Mounting the SDI-AP5R on page 15 Safety Information Do not attempt to service the appliance. This sealed unit contains no user-serviceable parts or adjustments. Do not open or tamper with the power supply. Carefully inspect the work area in which the SDI-AP3 and SDI-AP5 appliances will be located to ensure against hazards such as damp floors, ungrounded power extension cords, and missing ground connections. Before operating the appliance, ensure that external power sources comply with the requirements. Ensure that the ampere rating of all equipment plugged into wall outlets does not exceed the capacity of the outlet. If you require an extension cord, ensure that the ampere rating of all equipment plugged into the extension cord does not exceed the cord s ampere rating. If the SDI-AP3 and SDI-AP5 appliances are exposed to moisture or condensation, disconnect it from the power source immediately and obtain service assistance. SteelConnect Access Point Hardware Guide 11

12 Mounting the SteelConnect Access Point Appliances Mounting the SDI-AP3 and SDI-AP5 If the appliance exhibits unexpected behavior, such as smoking or becoming extremely hot, disconnect it from the power source immediately and then obtain service assistance. Environmental Considerations The following is a list of environmental considerations that will ensure safe and efficient operations of the appliance: Ensure that the appliance has at least 12 inches of clearance on all sides to allow for proper ventilation. The appliance generates heat and requires adequate circulation to maintain proper operating temperatures. Never cover or obstruct the appliance ventilation slots. Do not position the appliance near high-powered radio transmitters or electrical equipment, such as electrical motors or air conditioners. Interference from electrical equipment can cause intermittent failures. Do not install the SDI-AP3 and SDI-AP5 appliances in areas where condensation, water, or other liquids may be present. These may cause safety hazards and equipment failure. Mounting the SDI-AP3 and SDI-AP5 The SDI-AP3 and SDI-AP5 can be mounted to a wall or ceiling using the snap disk. If a solid mount is not required, the appliance can be used as a tabletop unit. Distance from the AP to the power supply source should be considered before mounting the AP. Note: For best radio coverage, the AP should be ceiling mounted. The AP ships with a snap disk, screw, and drywall anchor. Supply the AP with power by either using the power supply or a Power over Ethernet (PoE). Attach the power to the AP before mounting it. To mount the AP to a wall or ceiling 1. Use a power drill to drill pilot holes for the dry wall anchor. Insert the drywall anchor into the pilot hole. 2. Place the snap disk over the drywall anchor. Secure the snap disk to the wall by driving the screw into the drywall anchor. 3. Place the AP over the snap disk and snap it into place. 12 SteelConnect Access Point Hardware Guide

13 Installing the SDI-AP5R Mounting the SteelConnect Access Point Appliances 4. Plug in the power supply or PoE to power up the AP. Figure 2-1. Mounting the SDI-AP3 and SDI-AP5 Installing the SDI-AP5R You can mount the SDI-AP5R to a wall or a pole using the mounting kit that ships with the appliance. Make sure to mount all antennas as indicated on the device (2.4 GHz and 5 GHz) before mounting the appliance. Distance from the appliance to the power supply source should be considered before mounting it. The AP can only be powered by PoE+ (IEEE 802.3at) through the LAN1 port. Supply power by connecting the LAN1 port either to a PoE+ injector or a PoE+ capable switch port. Use the grounding strap that ships with the SDI-AP5R to prevent damage to the AP. Connect one end of the grounding strap to a grounding post with a screw and washer. Securely attach it to another nearby metal structure. Wall Mounting the SDI-AP5R 1. Mark the four locations on a flat surface for the mounting holes. Figure 2-2. Mounting Hole Locations SteelConnect Access Point Hardware Guide 13

14 Mounting the SteelConnect Access Point Appliances Installing the SDI-AP5R 2. Drill holes in the four marked locations. Each hole should be 37 mm (1.46 in.) deep and 8 mm (.31 in.) wide. Hammer the bolts into the openings. Figure 2-3. Installing the Bolts 3. Place the lock and flat washers on the four cap screws and use the screws to attach the bracket to the back of the appliance. Figure 2-4. Attaching the Bracket 14 SteelConnect Access Point Hardware Guide

15 Installing the SDI-AP5R Mounting the SteelConnect Access Point Appliances 4. Attach the device to the wall by tightening the bolt s flat washers and nuts to secure the bracket to the mounting surface. Figure 2-5. Securing the AP to the Wall Pole Mounting the SDI-AP5R 1. Place the lock and flat washers on the four cap screws and use the screws to attach the bracket to the back of the AP. Figure 2-6. Attaching the Bracket SteelConnect Access Point Hardware Guide 15

16 Mounting the SteelConnect Access Point Appliances Installing the SDI-AP5R 2. Determine placement (horizontal or vertical) and use the four round head screws to attach the pole mount bracket. Figure 2-7. Attaching the Pole Mount Bracket 3. Thread the open end of the pole strap through the two tabs on the pole mount brackets. Figure 2-8. Attaching the Straps to the Pole Mount Bracket 16 SteelConnect Access Point Hardware Guide

17 Connecting Power Mounting the SteelConnect Access Point Appliances 4. Lock and tighten the pole strap to secure the pole mount bracket to the pole. Figure 2-9. Secure the Pole Mount Strap Connecting Power The AP appliance can only be power by PoE+ through the LAN1 port. Supply power by connecting the LAN1 port to a PoE+ injector or a PoE+ capable switch port. Connecting to the Network Connect the AP to your local network. In order to find a SteelConnect Manager instance, the AP needs Internet access. Make sure the network provides a DHCP service so the AP can establish a connection automatically. Connector Requirements Follow these guidelines when considering cable options: Use CAT5e or higher connectors only SteelConnect Access Point Hardware Guide 17

18 Mounting the SteelConnect Access Point Appliances Connector Requirements Make sure the total plug length is 30 mm (1.3 in.) or less Remove the band protection with a cutter if needed. Remove the catch completely for easy maintenance. Place the sleeve around the cable and plug the connector into the appliance. Make sure to pull the screw cap tight. 18 SteelConnect Access Point Hardware Guide

19 A Specifications This appendix lists the specifications for the SteelConnect AP appliances. SDI-AP3 Specifications on page 20 SDI-AP5 Specifications on page 20 SDI-AP5R Specifications on page 21 SteelConnect Access Point Hardware Guide 19

20 Specifications SDI-AP3 Specifications SDI-AP3 Specifications Specification Radio Specification Interface Power Dimensions Weight Temperature Range Definition 1 x g/n radio on 2.4 GHz 1 x a/n radio on 5 GHz 600 Mbps max rate 2 x 2 MIMO with 2 spatial streams Internal diversity antennas 2 x 5dBi on 2.4 GHz 2 x 5dBi on 5 GHz 1 x GbE af Power-over-Ethernet 12V/2A DC power adapter (optional) 18.9 x 21.0 x 4.5 cm (7.44 x 8.26 x 1.77 i.n) 0.9 kg (2.0 lb) Operating: 0 to 40 C (32 to 104 F) Storage: -20 to 60 C (-4 to 140 F) SDI-AP5 Specifications Specification Radio Specification Interface Power Dimensions Weight Temperature Range Definition 1 x g/n radio on 2.4 GHz 1 x a/n/ac radio on 5 GHz (DFS) 1750 Mbps max rate 3 x 3 MIMO with 3 spatial streams Internal 3D sectorized antenna array 3 x 4dBi on 2.4 GHz 3 x 5dBi on 5 GHz 1x GbE 802.3at PoE 12V/2A DC power adapter (optional) 18.9 x 21.0 x 4.5 cm (7.44 x 8.26 x 1.77 i.n) 0.9 kg (2.0 lb) Operating: 0 to 40 C (32 to 104 F) Storage: -20 to 60 C (-4 to 140 F) 20 SteelConnect Access Point Hardware Guide

21 SDI-AP5R Specifications Specifications SDI-AP5R Specifications Specification Radio Specification Interface Power Dimensions Weight Temperature Range Definition 1 x g/n radio on 2.4 GHz 1 x a/n/ac radio on 5 GHz (DFS) 1750 Mbps max rate 3 x 3 MIMO with 3 spatial streams Omni-directional antennas (N type) 3 x 5dBi on 2.4 GHz 3 x 7dBi on 5 GHz 2 GbE 802.3at PoE 28.5 x 21.8 x 5.3 cm (11.22 x 8.58 x 2.10 in.) 4 kg (8.8 lb) Operating: -20 to 70 C (-4 to 158 F) Storage: -30 to 80 C (-22 to 176 F) SteelConnect Access Point Hardware Guide 21

22 Specifications SDI-AP5R Specifications 22 SteelConnect Access Point Hardware Guide