DePuy Synthes Mitek Sports Medicine Visualization System

Transcription

1 DePuy Synthes Mitek Sports Medicine Visualization System Setup & Troubleshooting Guide SHOULDER / KNEE / SMALL JOINT / HIP

2 1 : Visualization Front Side Setup CAUTION Ensure the backside wiring setup is complete and that all backside power switches are turned on. 1 POWER ON TOWER 1 Turn on the cart s main power switch. Turn on the front side power switch of each individual component. 2 ENTER PATIENT INFORMATION Select New Case on the Image Capture Unit. A surgical team member will then enter relevant patient data using a Keyboard or other external device. 2 3 STERILE PROCEDURE A surgical team member working within the sterile field will pass the equipment-end of the sterilized Camera Head Cable and Light Cable to a surgical team member outside the sterile field for attachment to their respective units. 3 4 ATTACH CAMERA HEAD TO CCU Remove protective cap from Camera Head Cable. Attach Camera Head Cable to CCU (Camera Control Unit) by aligning the red dots and pushing into the CCU. 4 5 ATTACH LIGHT CABLE TO LIGHT SOURCE Make sure that the light turret is turned so the correct position is on top and that it matches the style of the Light Cable. DePuy Synthes Mitek Sports Medicine Light Cables use the Storz connection here. 5 2

3 1 : Visualization Front Side Setup 6 ATTACH COUPLER TO CAMERA HEAD Attach the desired Coupler to the Camera Head by screwing them together. All surfaces should be dried thoroughly before attaching to ensure no fogging occurs. 6 NOTE: It is recommended to use 2 different gauze pads with a 1 minute wait time between wiping down all surfaces. 7 7 ATTACH SCOPE TO COUPLER Attach the desired Scope to the Coupler. All surfaces should be dried thoroughly with gauze pad before attaching. NOTE: Press locking mechanism to accept desired Scope. Once inserted, push button in opposite direction to lock Scope into place. 8 8 ATTACH LIGHT CABLE TO SCOPE The DePuy Synthes Mitek Sports Medicine Light Cable uses an ACMI connection here. All Scope rings should be removed from the Scope s light-post to access this connection. 9 NOTE: DePuy Synthes Mitek Sports Medicine Light Cable Connections Proximal Storz / Distal ACMI 9 WHITE BALANCE THE CAMERA Make sure the Light Source is turned on and not in Standby Mode. Place several gauze pads approximately 1 inch from the Scope tip and wait 1-2 seconds for shutter to adjust. 9 Then press-and-hold the + / WB button on the Camera Head for approximately 3 seconds. When the White Balance is complete, a green check mark appears over the WB symbol on the Display. 10 ATTACH SHEATH TO SCOPE Attach the Sheath to the Scope and the Sheath s Stopcocks to the appropriate FMS Fluid Management System inflow and outflow connection tubes. 10 3

4 2 : Visualization Backside Setup Connect Camera Control Unit to Display DVI 1 out > DVI 1 in Connect Camera Control Unit to Image Management System DVI 2 out > DVI in Connect Image Management System to Display HDMI out > DVI 2 in Connect Camera Control Unit to Image Management System (connect cable with red band to Remote 2) Remote 1&2 out > MedX EVO GPIO Port Connect Image Management System to Printer USB out > USB in Connect Image Management System to Wireless Imaging Control USB out > USB in Ethernet NIC > Ethernet in Connect Display to Wireless Transmitter (Tx) (see next page for secondary display setup) DVI out > DVI in Power to all units from power strip inside tower DVI > DVI HDMI > DVI Image Management System Power Power Splitter (for use w/ Wireless Imaging) DIGITAL PRINTER IMAGE MANAGEMENT SYSTEM LIGHT SOURCE CAMERA CONTROL UNIT DISPLAY WIRELESS TRANSMITTER (Tx) Remote > GPIO Display Power USB & Ethernet (wireless control power & network) Printer Power 4

5 2 : Visualization Backside Setup Wireless Imaging/Secondary Display VISUALIZATION TOWER WIRELESS TRANSMITTER (Tx) SECONDARY DISPLAY WIRELESS RECIEVER (Rx) 1 Connect Wireless Receiver (Rx) to Secondary Display DVI 1 out > DVI 1 in DVI > DVI Display Power Power Splitter (for use w/ Wireless Imaging) 2 Power to wireless units utilizing power splitter off display power Wireless Setup Bonding Wireless Units 1 Press and hold the bond button (see image 1 for location) on the transmitter (Tx) unit until its LED begins flashing orange rapidly, then release. NOTE: Ensure both displays are powered on prior to performing the pairing procedure Next press and hold the bond button (see image 2 for location) on the receiver (Rx) unit until its LED begins flashing orange rapidly, then release. 3 3 When the bonding process is complete each unit s LED will be steady blue. 5

6 3 : Troubleshooting PROBLEM CAUSES POSSIBLE SOLUTION Device will not power on Live video does not display LCD screen does not function Camera indicator light does not turn on Power cable unplugged Supply Mains switch OFF Power switch OFF Fuse is blown Video cart is not powered ON Camera Head (TCKI) not connected Video cable not connected to the device Video cable not connected to the Display Display is not powered ON Display cannot accept video resolution Supply Mains switch powered OFF Power switch OFF Display not connected to power source Display set to wrong input Supply Mains switch OFF Power switch OFF Camera Head (TCKI) not connected Camera Head (TCKI) not recognized by device Supply Mains switch OFF Power switch OFF Ensure power cable is plugged in Power ON Supply Mains switch Power ON Power switch Replace fuse Power ON video cart Connect Camera Head (TCKI) Connect video cable to device output Connect video cable to Display input Power ON Display Use a display which complies with the technical specifications Power ON Supply Mains switch Power ON Power switch Connect Display to power source Set Display to correct input Reset Camera Control Unit (OVBI) by powering OFF and the ON the Supply Mains Power switch Power ON Supply Mains switch Power ON Power switch Connect Camera Head Camera Head (TCKI) ) to device Ensure the Camera Head (TCKI) is properly connected Reset Camera Control Unit (OVBI) Power ON Supply Mains switch Power ON Power switch 6

7 3 : Troubleshooting PROBLEM CAUSES POSSIBLE SOLUTION Loss of video Video output cable disconnected from device Video output cable disconnected from Display Display disconnected from power or turned off Display settings changed Device disconnected from power or powered off Video resolution changed Video timing changed Light Source power off Connect video cable to device output Connect video cable to Display input Ensure Display is connected to power and turned on Ensure Display settings are correctly set Ensure device is connected to power with Supply Mains switch powered ON Power ON Power switch Video resolution changes cause temporary video loss If video loss persists, reset device Video timing changes cause temporary video loss If video loss persists, reset device Turn Light Source on Color bars display Camera Head (TCKI) disconnected Reconnect Camera Head (TCKI) Incorrect color representation Video too dark Video too bright Improper White Balance Device is in Fiberscope Specialty Debris on Endoscope tip Debris on Device window or Coupler optics Improper video settings Exposure level too low Light Source too low Obstruction in light path Brightness level too low Gamma level too low Brightness level set too high Automatic shutter fault Light Source too bright Ensure screen is white and contains detail Bright white without detail will not white balance correctly Fiberscope Specialty may cause poor color quality Clean Endoscope tip Remove Coupler from device and clean glass surfaces on device and Coupler Adjust video settings or reset settings to factory defaults Increase exposure until any area in the image is too bright Increase Light Source level Check Light Cable and Scope for broken fibers or light obstruction at Scope tip Increase the brightness level Increase the gamma level Decrease brightness level Reset Camera Control Unit (OVBI) Decrease Light Source brightness 7

8 3 : Troubleshooting PROBLEM CAUSES POSSIBLE SOLUTION Image is not well centered on display Image out of focus Foggy image Grainy image Buttons on device do not function Keyboard does not function Images not storing on flash drive Cannot capture video Endoscope not centered on Coupler Coupler or Endoscope not properly focused from device Endoscope not seated on Coupler Debris on Endoscope tip Debris on device window or Coupler optics Moisture/debris on Endoscope tip Moisture/debris on device window or Coupler optics Enhance Level too high Device not connected to Camera Control Unit (OVBI) Buttons damaged Improperly connected Keyboard Invalid Keyboard Keyboard or Keyboard cord is damaged Improperly connected flash drive Invalid flash drive Camera Head (TCKI) buttons Flash drive full Image Management System Improperly connected Image Management System Remove Endoscope from Coupler and re-attach Focus Coupler following Coupler IFU instructions Remove Endoscope from Coupler and re-attach Clean Endoscope tip Remove Coupler from device and clean glass surfaces on device and coupler Clean Endoscope tip Remove Coupler from device and clean glass surfaces on device and Coupler Reduce Enhance Level Reset Camera Control Unit (OVBI) Connect device to Camera Control Unit (OVBI) Reset Camera Control Unit (OVBI) Consult Warranty/Service Return information Connect Keyboard correctly Connect correct Keyboard Repair or replace Keyboard Reset Camera Control Unit (OVBI) Connect flash drive correctly Connect correct flash drive See Buttons on device do not function problem listed above Reset Camera Control Unit (OVBI) Remove images from flash drive using a computer and retry Consult Image Management System IFU Connect video output cable and remote cable to Image Management System and Camera Control Unit (OVBI) 8

9 3 : Troubleshooting PROBLEM CAUSES POSSIBLE SOLUTION Cannot capture video (continued) Printer not printing Pictures not storing on video capture device Invalid Image Management System Camera Head (TCKI) buttons LCD screen Improperly connected Printer Printer is out of paper or out of ink Invalid Printer Camera Head (TCKI) buttons LCD screen Image Management System Improperly connected Video Capture Device Invalid Image Management System Camera Head (TCKI) buttons LCD screen Connect correct Image Management System See above and re-attach Consult Printer IFU Connect USB cable to Image Management System and Camera Control Unit (OVBI) Add paper, replace cartridge Connect correct Image Management System See Buttons on device do not function problem listed on page 8 Consult Image Management System IFU Connect video output cable and remote cable to Image Management System and Camera Control Unit (OVBI) Connect correct Image Management System See Buttons on device do not function problem listed on page 8 FURTHER TROUBLESHOOTING For problems which arise that are not remedied by any of the above means, cycle the device power off and on. If this does not solve the problem, please refer to the individual component IFU s and/or contact your sales consultant or call the 24-Hour Technical Hotline at * Please call the 24-Hour Technical Hotline at the number above for step-by-step instructions on how to reset the Camera Control Unit (OVBl). 9

10 Limited Warranty and Disclaimer: DePuy Mitek, Inc. products are sold with a limited warranty to the original purchaser against defects in workmanship and materials. Any other express or implied warranties, including warranties of merchantability or fitness, are hereby disclaimed. WARNING: In the USA, this product has labeling limitations. See package insert for complete information. CAUTION: USA Law restricts these devices to sale by or on the order of a physician. Not all products are currently available in all markets. The third party trademarks used herein are trademarks of their respective owners. DePuy Mitek, Inc. 325 Paramount Drive Raynham, MA T. +1 (800) DePuy Synthes Mitek Sports Medicine, a division of DOI All rights reserved. DSUS/MTK/0515/0580(1) 11/15