OCM5 Splitters and Pass-Through Modules for CSX-3 Cabinets
|
|
- Theodore Miller
- 5 years ago
- Views:
Transcription
1 OCM5 Splitters and Pass-Through Modules for CSX-3 Cabinets I N S T A L L A T I O N I N S T R U C T I O N 1.0 General Product Information Splitters for the CSX-3 cabinets are purchased and installed as needed. Each splitter module is equipped with up to 32 connectorized output fibers. The splitter distribution connectors (pigtails) can be stored in the parking lot area for later use or connected immediately to the distribution ports. Pass-through modules provide the capability for a feeder cable signal to be routed directly to a distribution port, by-passing a splitter module and providing full feeder signal strength to a customer. Pass-through modules are designed to be placed alongside OCM5 splitter modules for consistent and organized cable management. Splitter Module Input Parking Lot Figure 1: OCM5 Splitter Module Kit 2.0 Kit Contents The OCM5 Splitter Module Kit consists of: Pass-through Module OCM5 splitter module with pigtails pre-installed in two parking lot rails (Figure 1) Installation instructions Splitter serial number label GPON labels for splitter module housing and pigtails The Pass-Through Module Kit consists of: Pass-through module with pigtails pre-installed in one or two parking lot rails (Figure 2) Installation instructions Pass-through serial number label Blue ID labels for pigtail identification Parking Lot Rail Figure 2: Pass-Through Module Kit 3.0 Safety Precautions DANGER: Do not look into the ends of any optical fibers. Eye damage from exposure to laser radiation may result. Do not assume the laser power is turned off or that the fiber is disconnected at the other end. Output Ports Splitter or pass-through module rack Parking Lot Input Ports
2 4.0 Splitter or Pass-Through Module Installation 4.1 Installing the Splitter or Pass-Through Module 1. To install a splitter or pass-through module, simply locate the next available slot in front of any existing splitter or pass-through modules, and slide the new module left into the slot until it clicks, indicating that it is locked in position. 2. Locate the splitter or pass-through serial number label shipped with the module. Apply that label to the splitter/ pass-through location matrix label in the appropriate module position block. Note: If the splitter cabinet has both BPON and GPON services, apply the supplied green GPON labels to the narrow face of the splitter module housing near the pigtail exit, and to the pigtails 1/2 behind the serial number labels, for those splitter modules running GPON grade service. Pass-through modules come equipped from the factory with dark blue pre-installed port ID labels. If two pass-through modules are installed per cabinet, the user should install the factory-supplied light blue labels over the dark blue labels on the second module, for easier field differentiation of housings and pigtails. If three pass-through modules are installed per cabinet, the user should install the light blue labels 1/2 behind the dark blue labels. OCM5 Splitter or Pass-Through Module Splitter/Pass-Through Location Matrix Label Parking Lot location 3. Splitter and pass-through modules are shipped with the output pigtails pre-installed into parking lot rails. Route the rails with pigtails to the parking lot and plug into the rectangular slots. Note: Do not remove the pigtails from the parking lot rails when routing. 4. Route the input fiber(s) from the splitter or pass-through module through the inside channel as shown and down to the input port panel. Center channel
3 Ferrule dust caps are included on the connectors inside the parking lot rails as supplied by Tyco Electronics. Do not remove the dust caps until the connectors are ready to be terminated in the designated shelf adapter. Note: Route the parking lot rails to the parking lot area as instructed in the routing diagrams for the CSX-3 cabinets, which are provided in the CSX-3 Cabinet Installation Instructions and located inside the cabinet. 5. As connections are made within the CSX-3 cabinet, pigtails are removed from the parking lot and rails are emptied. Discard empty rails and move full or partially full rails to the left, as shown in the diagram at right. CSX Cabinets CSX & 432 Cabinets Connectors Connectors (empty, discard) This is the original order in which parking lot rails from the splitter or cross-connect modules should be stored in the parking lot. (empty, discard) This is the original order in which parking lot rails from the splitter or cross-connect modules should be stored in the parking lot. When rails are empty, discard them and move all the other rails one position to the left (or up and to the right) When rails are empty, discard them and move all the other rails one position to the left.
4 4.2 Connecting Pigtail to Input Port 1. The input ports are located at the bottom of the hinged termination panel. CSX and 432 cabinets input panels can be configured with 24, 48, or 72 ports. CSX cabinets input panels may be two 24-port panels, two 48-port panels, or two 72-port panels. 2. To clean the input port, open the hinged dust cap and clean with locally approved cleaning methods and materials. Plug the input fiber into the cleaned input port to activate the splitter or pass-through module. Note: Always follow company-approved or industrystandard practice when cleaning connectors. 4.3 Connecting Pigtails to Output Ports 1. Remove the selected output pigtail from the parking lot rail. Remove the dust cap and clean the splitter or passthrough pigtail connector and the selected output port per locally approved practice. 2. Connect the pigtail connector to the output port. 3. Dress any pigtail slack using the routing rings below the output panel. 4.4 Removing a Splitter or Pass-through Module 1. To remove a splitter or pass-through module from the CSX-3 cabinet, press the button marked PUSH near the splitter and pass-through module storage rack, and slide the module out from the rack 5.0 Cleaning the Adapters, if Necessary If, after proper connection, the fiber exhibits higher than acceptable levels of loss, it is possible that there is dirt in the adapter connections on the back side of the termination panel. 1. To open the swing frame, press the latch labelled UNLOCK, and swing the frame outward as shown. 2. Identify the input and output ports in question.
5 3. Disconnect the input port fiber and clean the back side connector and adapter per locally approved practice. Reconnect the input port fiber. 4. Disconnect the output port fiber, clean the adapter, and reconnect. 5. Pull up on the door stop to allow the hinged termination panel to close. 6. Test the fiber to confirm proper operation. If it is still not functioning propertly, disconnect/re-clean/reconnect the input and output pigtail connectors and both adapters on the front side of the hinged termination panel. Refer to the CSX-3 cabinet installation instructions for procedures regarding closing, maintaining, and repairing the cabinet. Tyco Electronics Corporation 8000 Purfoy Road Fuquay-Varina, NC Tel.: Fax: TE logo, Tyco Electronics, and CSX-3 are trademarks. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, Tyco Electronics Corporation makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. Tyco Electronics obligations shall only be as set forth in Tyco Electronics Standard Terms and Conditions of Sale for this product and in no case will Tyco Electronics be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of Tyco Electronics products should make their own evaluation to determine the suitability of each such product for the specific application Tyco Electronics Corporation All rights reserved. PML B9210C F622.03/08
Optical Line Splitter Installation Instructions
Optical Line Splitter Installation Instructions TECP-96-171 Issue 1 9/2011 Content Page INTRODUCTION............................................................................. 1 1 INSTALLATION.........................................................................
More informationFACT OPTICAL DISTRIBUTION FRAME SYSTEM
FACT OPTICAL DISTRIBUTION FRAME SYSTEM Fiber Connectivity for Splice/ Patch and Patch/Patch For almost 30 years, TE Connectivity has led the industry with solutions such as FIST fiber management system,
More information3 Angled Connector Housing (MC) Installation
Angled Connector Housing (MC) Installation Instructions July 1999 4-7047-2554-7 MC Frame Figure 1 Angled Connector Housing (MC) General This document describes the installation of the stubbed MC Angled
More informationNext Generation Frame Fiber Termination Block With MPO Connectors (FTB w/mpo) User Manual
Next Generation Frame Fiber Termination Block With Connectors ( w/) User Manual ADCP-90-372 Issue 2 4/2010 23867-A Block With Connectors 1685947 Rev A Preface COPYRIGHT 2008, ADC Telecommunications, Inc.
More informationC5C Cross-Connect System
C5C Cross-Connect System I N S T A L L A T I O N I N S T R U C T I O N High-Density Connection Blocks 1.0 General Product Information The C5C cross-connect system is comprised of a high-density connection
More informationPRINTER ACCESSORIES TECHNICAL DATASHEET UNIVERSAL REEL HOLDER
PRINTER ACCESSORIES TECHNICAL DATASHEET TTDS-260 issue 3, July 2015 UNIVERSAL REEL HOLDER The Universal reel holder is a free standing bench top, or wall mounted reel holder. Designed to dispense all TE
More information3M Add-On Terminals 4220P (100, 200, 300 & 400 pairs)
3M Add-On Terminals 4220P (100, 200, 300 & 400 pairs) Instructions August 2011 3 78-8130-2330-1-C 1.0 General 1.1 The 3M Add-On Terminals 4220P-100, 4220P-200, 4220P-300 and 4220P-400 are designed to expand
More informationINDUSTRIAL MINI I/O CONNECTOR
INDUSTRIAL MINI I/O CONNECTOR The Industrial Mini I/O connector system is a compact, wire to wire and wire-to-board solution for reliably serial, bus and Ethernet connections in industrial applications.
More informationFiber Management Tray (FMT) User Manual
Fiber Management Tray (FMT) User Manual Fiber Management Tray Content Page INTRODUCTION............................................................................. 2 ADMONISHMENTS...........................................................................
More informationPRINTER ACCESSORIES TECHNICAL DATASHEET UNIVERSAL REEL HOLDER
PRINTER ACCESSORIES TECHNICAL DATASHEET TTDS-260 issue 4, FEBRUARY 2018 UNIVERSAL REEL HOLDER The Universal reel holder is a free standing bench top, or wall mounted reel holder. Designed to dispense all
More informationTrueNet TFP Series Rack Mount Fiber Panels
TFP Series Rack Mount Fiber Panels The rack mount TrueNet Fiber Panel (TFP) is an integral part of the TrueNet Fiber product portfolio. The TFP fiber panels can be ordered in one, two and five rack unit
More informationOrdering Guide for FIST Blue Label Racks (FIST-GR3)
Page 1 of 13 Ordering Guide for FIST Blue Label Racks (FIST-GR3) This document provides assistance with the selection of racks for use in FIST applications. It includes the following sections: 1 Product
More informationTwo Rack Unit (2RU) Fiber Management Tray (FMT) User Manual
Two Rack Unit (2RU) Fiber Management Tray (FMT) User Manual 18701-B 2RU FMT (Micro-VAM Configuration Shown) Content Page INTRODUCTION.............................................................................
More informationPRINTING RIBBONS AND INKS TECHNICAL DATASHEET
PRINTING RIBBONS AND INKS TECHNICAL DATASHEET Revision 6, March 2016 Section 1, Contents SECTION PAGE SECTION DESCRIPTION COLOUR AND TYPE Section 1 Page 1 CONTENTS Section 2 Page 2 1966-RIBBONS, 2000P-4TT,
More informationRUFIS. Remote Radio Head (RRH) Unit Field Installation System. Ease your transition towards next generation base stations
Remote Radio Head (RRH) Unit Field Installation System Ease your transition towards next generation base stations Introduction Remote Radio Heads improve efficiency of next generation wireless base stations
More informationOrdering Guide of the Single-Mode Connectorized Fiber Cables (Pigtails & Jumpers) and Single-Mode Connector Mating Adapters
Page 1 of 9 Ordering Guide of the Single-Mode Connectorized Fiber Cables (Pigtails & Jumpers) and Single-Mode Connector Mating Adapters This document provides assistance with the selection of single-mode
More information3M Compact Coarse Wave Division Multiplexer (CCWDM) Module Installation
3M Compact Coarse Wave Division Multiplexer (CCWDM) Module Installation Instructions June 2010 3 Contents 1.0 Introduction...3 2.0 Kit Contents...3 3.0 Preparation and Installation of One and Two 3M Compact
More informationMEAS HTU21D PERIPHERAL MODULE
MEAS HTU21D PERIPHERAL MODULE Digital Humidity and Temperature Digital Component Sensor (DCS) Development Tools The HTU21D peripheral module provides the necessary hardware to interface the HTU21D digital
More informationFL1000 Wall-Mount Box Installation and Operation Guide
FL1000 Wall-Mount Box Installation and Operation Guide ONE DOOR (FL1-B) TWO DOOR (FL1-H) 19706-B FL1000 Wall-Mount Box Content Page INTRODUCTION.............................................................................
More informationFullAXS CONNECTOR SEALING & CABLE ASSEMBLY
FullAXS CONNECTOR SEALING & CABLE ASSEMBLY System Solution Guide Next Generation x-tta Solution Next generation WiMAX and Long Term Evolution (LTE) Fiber/Power/Signal To The Antenna (x-tta) connectivity
More informationOutdoor FDH Termination Pole-Mount Cabinet With Universal Splitter Chassis User Manual
Outdoor FDH 3000 288 Termination Pole-Mount Cabinet With Universal Splitter Chassis User Manual ADCP-96-184 Issue 1 8/2014 25555-A 300100104431 Rev A Preface COPYRIGHT 2014, Tyco Electronics Corporation
More informationREMOTE INPUT/ OUTPUT TERMINAL SYSTEM (RITS) CONNECTORS
REMOTE INPUT/ OUTPUT TERMINAL SYSTEM (RITS) CONNECTORS A concept that is saving your most valuable asset your time. The contact design based on insulation displacement of our RITS (Remote I/O Termination
More informationMEAS TEMPERATURE SYSTEM SENSOR (TSYS01) XPLAINED PRO BOARD
MEAS TEMPERATURE SYSTEM SENSOR (TSYS01) XPLAINED PRO BOARD Digital Temperature Digital Component Sensor (DCS) Development Tools Performance -5 C to 50 C accuracy: 0.1 C -40 C to 125 C accuracy: 0.5 C Very
More information6100E Series DIGITAL FIBER OPTIC MULTI-CHANNEL AUDIO TRANSPORT SYSTEM
00E Series DIGITAL FIBER OPTIC MULTI-CHANNEL AUDIO TRANSPORT SYSTEM WITH DATA OPTIONS BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability
More informationFLAT FLEXIBLE CABLE (FFC) CONNECTORS
FLAT FLEXIBLE CABLE (FFC) CONNECTORS TE Connectivity s (TE) family of FFC connectors includes a variety of high density cable-to-board and cable-to-cable connectors designed for automated assembly. The
More informationSGJ Cable Actuated Sensor Industrial CANBus J1939
Cable Actuated Sensor Industrial CANBus J939 Two Available Stroke Ranges: 0-80 in & 0-20 in. Rugged Polycarbonate Enclosure Simple Installation Compact Design Built for IP67 environments IN STOCK FOR QUICK
More informationFIST. Fiber Infrastructure System Technology. Generic Racks (FIST-GR2)
FIST Ordering Guide FIST Fiber Infrastructure System Technology Generic Racks (FIST-GR2) This document provides assistance with the selection of racks for use in FIST applications. It includes the following
More informationHigh Density PEACOC v. 3.0 Fiber Patch Panel& FleT
High Density PEACOC v. 3.0 Fiber Patch Panel& FleT Patch panel with Enhanced Accessibility for Compact Optical Connectors Flexible Trays to Integrate Optical Components such as NGPON2, xwdm, Splitter,
More informationCable Routing Procedures for Dell PowerEdge R630 Systems
Cable Routing Procedures for Dell PowerEdge R630 Systems This Dell Technical White Paper explains the best practices for routing and securing the cables exiting the back of the R630 systems. Rail Solutions
More informationT600 TACHOMETER MultiTasker - a measurement & monitoring instrument with 2 frequency and 1 analog inputs
TACHOMETER MultiTasker - a measurement & monitoring instrument with 2 frequency and 1 analog inputs Features High accuracy speed measurement: 0.002% for limits and 0.1% referenced to 20 ma 2 frequency
More informationwith Fiber Management Bar
Issue 1, June 2014 SYSTIMAX 1100A Angled Fiber Termination Panel with Fiber Management Bar General The SYSTIMAX 1100A angled fiber termination panel is a 19 wide x 1.75 high (483mm x 44mm) 1U panel designed
More informationSATA II HDD Canister KISS DA 435 Quick Reference Guide
SATA II HDD Canister KISS DA 435 Quick Reference Guide If it s embedded, it s Kontron 1. Table of Contents SATA II HDD Canister KISS DA 435 1. Table of Contents 1. Table of Contents... 1 2. Important Information...
More information3M DSLAM Mounting Bracket Kit J0746
3M DSLAM Mounting Bracket Kit J0746 Instructions July 2009 3 Contents 1.0 3M DSLAM Mounting Bracket J0746 - Installation...3 2.0 DSLAM Installation, Nokia...5 3.0 Accessory Kit, Cable Addition Shroud J0747
More informationRMG Series Rack Mount Fiber Enclosures
The RMG Series rack mount fiber enclosures is as an integral part of the TE Connectivity product portfolio. The RMG Series fiber enclosure provides rugged and durable protection for patching or splicing
More information1. If the impaired node is part of an HA pair, disable automatic giveback from the console of the healthy node:
AFF A200 systems Replacing DIMMs You must replace a DIMM in the controller module when your system registers an increasing number of correctable error correction codes (ECC); failure to do so causes a
More informationTrueNet 1U and 2U Fiber Panel Installation and Cable Routing Instructions
TrueNet 1U and 2U Fiber Panel Installation and Cable Routing Instructions ADCP-92-082 Issue 2 10/2008 1U PANEL 2U PANEL 22049-A Content Page INTRODUCTION.............................................................................
More informationAlphaServer DS20 Ultra SCSI Internal StorageWorks Shelf Configuration Guide
AlphaServer DS20 Ultra SCSI Internal StorageWorks Shelf Configuration Guide Order Number: EK-H8253-IN. A01 Compaq Computer Corporation Maynard, Massachusetts First Printing, November 1998 The information
More informationThis diagram shows the workflow of the DIMM replacement procedure for a FAS2600 system.
FAS2600 series Replacing DIMMs This diagram shows the workflow of the DIMM replacement procedure for a FAS2600 system. Video overview This video shows an overview of the DIMM replacement procedure for
More informationAMP NETCONNECT* Gen II Vertical Storage Area Management (SAM) System
AMP NETCONNECT* Gen II Vertical Storage Area Management (SAM) System Application Specification 114-32037 29 AUG 12 NOTE i All numerical values are in metric units [with U.S. customary units in brackets].
More informationLBO-H2 Series DIRECT PLUGGABLE LINKBRIDE TM FIBER OPTIC HDMI 2.0 TRANSMISSION SYSTEM
LBO-H2 Series DIRECT PLUGGABLE LINKBRIDE TM FIBER OPTIC HDMI 2.0 TRANSMISSION SYSTEM BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability
More informationP-SERIES INCLINOMETER
SPECIFICATIONS Single or Dual axis inclinometer Measurement range +/-5,+/-15 or +/- 45 High accuracy Digital and analogue output signal FEATURES Measurement range up to +/-45 High resolution Robust metal
More informationOptiTect Indoor Local Convergence Cabinet, Gen III Series
Features and Benefits Industry-leading cabinet size Significant freight, storage and installation efficiencies Full factory-stubbed cabinets Enables quicker installation and rapid emergency restoration
More informationUSB Ranger 422 User Guide
USB Ranger 422 User Guide Featuring ExtremeUSB Technology USB Ranger 422 Thank you for purchasing the USB Ranger. Please read this guide thoroughly before installation. This document applies to Part Numbers:
More information3-4 SAS/SATA II HDD Canister Entry version USER S MANUAL XC-34D1-SA10-0-R. Document number: MAN A
3-4 SAS/SATA II HDD Canister Entry version XC-34D1-SA10-0-R USER S MANUAL Document number: MAN-00077-A ii Preface Important Information Warranty Our product is warranted against defects in materials and
More informationAMP-LATCH RIBBON CABLE INTERCONNECT SOLUTIONS
AMP-LATCH RIBBON CABLE INTERCONNECT SOLUTIONS Quick Reference Guide AMP-LATCH connectors are ribbon cable-to-board devices used to make the transition between ribbon cable and pc board circuitry. They
More information3M Indoor Protected Building Entrance Terminal 4588V-QCS Series
3M Indoor Protected Building Entrance Terminal 4588V-QCS Series with 3M Quick Connect System 2811 Dry Flame Retardant Block Instructions Underwriters Laboratories (UL 348X) Listed April 2010 3 78-0013-1813-4-A
More informationOPERATION MANUAL SERIES BORESCOPES INSTRUMENT TECHNOLOGY, INC. POB 381, Westfield, MA Airport Road, Westfield, MA 01085
OPERATION MANUAL SERIES 123000 BORESCOPES INSTRUMENT TECHNOLOGY, INC. POB 381, Westfield, MA 01086 33 Airport Road, Westfield, MA 01085 Tel: (413) 562-3606 Fax: (413) 568-9809 Email: iti@scopes.com www.scopes.com
More informationMPP200 User s Manual
2011 Visionary Solutions, Inc. All rights reserved. Please visit the support section of our website at www.vsicam.com for manuals, other documentation, and software downloads. Visionary Solutions, Inc.
More informationQuick Start Guide. GV-AS / EV Controller
Quick Start Guide GV-AS / EV Controller Thank you for purchasing GV-AS / EV Controller (GV-AS100 / AS110 / AS120 / AS210 / AS400 / AS410 / AS810 and GV-EV48). This guide is designed to assist the new user
More information3M Passive Optical Splitter Shelves and Modules
Communication Markets Division 3M Passive Optical Splitter Shelves and Modules 3M offers a robust portfolio of passive optical fiber splitter products made to enable easy configuration, design, ordering,
More informationVOLITION INTERCONNECT VF-45 STYLE
Volition Cabling System VOLITION INTERCONNECT VF-45 STYLE 62.5/125µm Fiber 3Innovation 1. Product Description & Requirements Volition Interconnect (VF-45 ) Socket and Patch Cords The Volition VF-45 Interconnect
More informationMULTIPORT SERVICE TERMINALS (MST)
MULTIPORT SERVIE TERMINLS (MST) s (TE) FTTX infrastructure solutions are designed from the ground up to meet the unique requirements of FTTX networks. esigned for operational efficiency and scalability,
More informationOPERATION MANUAL SERIES MICRO BORESCOPES INSTRUMENT TECHNOLOGY, INC. POB 381, Westfield, MA Airport Road, Westfield, MA 01085
OPERATION MANUAL SERIES 124000 MICRO BORESCOPES INSTRUMENT TECHNOLOGY, INC. POB 381, Westfield, MA 01086 33 Airport Road, Westfield, MA 01085 Tel: (413) 562-3606 Fax: (413) 568-9809 Email: iti@scopes.com
More informationIndoor Protected Entrance Terminal 4588 Series
Indoor Protected Entrance Terminal 4588 Series Instructions Underwriters Laboratories (UL) Listed September 2003 78-8135-1209-8-A 1.0 General The 3M Indoor Protected Entrance Terminal (PET) 4588 Series
More informationipad Charge & Sync Cart Model MCC2 ipad Cart 430-MCC2-User Manual-010 Is a Registered Trademark of Apple Inc. ipad
ipad Charge & Sync Cart Model MCC2 ipad Cart ipad Is a Registered Trademark of Apple Inc. 430-MCC2-User Manual-010 1. ipad Cart Specifications MCC2 Mobile Charge & Sync Cart Extra Drawer Reserved space
More information4800 Series FIBER OPTIC DVI EXTENSION SYSTEM
4800 Series FIBER OPTIC DVI EXTENSION SYSTEM BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed as a result of their use or
More informationMPP1700 User s Manual
2011 Visionary Solutions, Inc. All rights reserved. Please visit the support section of our website at www.vsicam.com for manuals, other documentation, and software downloads. Visionary Solutions, Inc.
More information6400 CWDM Series. Fiberlink. 4 or 8 Channel Coarse Wave Division Multiplexers for Single Mode Fiber. User s Manual
Communications Specialties Fiberlink 6400 CWDM Series User s Manual Coarse wave division multiplexers (CWDM) allow 4or 8 fiber optic links to operate at different wavelengths over a single fiber. It s
More informationInternal Cabling Guide for the HP Smart Array 6400 Series Controller on an HP Integrity Server rx7620
Internal Cabling Guide for the HP Smart Array 6400 Series Controller on an HP Integrity Server rx7620 May 2004 (Second Edition) Part Number 5990-8201 2004 Hewlett-Packard Development Company, L.P. Microsoft
More informationD-SERIES INCLINOMETER
SPECIFICATIONS Dual axis inclinometer Measurement range +/-5 +/-15 or +/-30 High accuracy Digital and analogue output signal CANopen CE approved FEATURES High accuracy Robust metal housing, IP Class 67/68
More informationMini-DVI-WP Series WALL PLATE MINIATURE MULTIMODE FIBER OPTIC DVI TRANSMISSION SYSTEM
Mini-DVI-WP Series WALL PLATE MINIATURE MULTIMODE FIBER OPTIC DVI TRANSMISSION SYSTEM BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability
More information7x50 High Scale (HS) MDA Installation Guide
7x50 High Scale (HS) MDA Installation Guide November 2008 Document Part Number: 93-0235-01-01 *93-0111-03-01* Copyright 2008 Alcatel-Lucent All rights reserved. November 2008. No portion of this document
More informationCSS1 Contractor Series Light Sources and CSM1 Contractor Series Optical Power Meters User s Guide
CSS1 Contractor Series Light Sources and CSM1 Contractor Series Optical Power Meters User s Guide www.aflglobal.com or (800) 321-5298, (603) 528-7780 Limited Warranty All NOYES test equipment products
More informationReplacing a PCIe card
AFF A700s systems Replacing a PCIe card To replace a PCIe card, you must disconnect the cables from the cards in the riser, remove the riser, replace the riser, and then recable the cards in that riser.
More informationTHUNDERBAY 4. Assembly Manual & User Guide
THUNDERBAY 4 Assembly Manual & User Guide CONTENTS Introduction...1 1.1 Minimum System Requirements 1.1.1 Apple Mac Requirements 1.1.2 PC Requirements 1.1.3 Supported Drives 1.2 Package Contents 1.3 About
More informationUSB Memory Drive CD with Application Software and Drivers for Windows 98SE. 32 MB, > 64 MB recommended. min. 2x (for probable installation)
User Manual USB Memory Drive Content: Included with USB Memory Drive...1 System Requirements...1 Warranty...2 Making Copies of This Manual...2 Notes on this Manual...3 Data Security...3 Operational Safety...3
More informationF1x3L Fiber Optic Tap LC
F1x3L Fiber Optic Tap LC CUSTOMER SUPPORT INFORMATION To order or for a technical information support: Phone: +33 3 88 10 18 30 or Fax: +33 3 88 10 18 35 Mail order: COMCRAFT 17A, rue des Frères Lumière
More informationULTIMATE-PRECISION DIGITAL LBB
ULTIMATE-PRECISION DIGITAL LBB SPECIFICATIONS High precision, 0.1% of reading or 1μm EMI and ESD protected (CE certified) Spring actuated probes Robust cast aluminum case (electronics) Stackable with T-Connectors
More informationINSTALLATION AND USER GUIDE 2800MWB SINGLE LINE BASIC FEATURE TELEPHONE
INSTALLATION AND USER GUIDE 2800MWB SINGLE LINE BASIC FEATURE TELEPHONE TeleMatrix Copyright 2005 COMPLIANCE AND SAFETY As specified by FCC regulation, we are required to inform you of specific governmental
More informationAEROSPACE, DEFENSE & MARINE /// MC801 FIBER OPTIC CONNECTORS
MC801 FIBER OPTIC CONNECTORS RUGGED, RELIABLE CONNECTIVITY COMBINING HIGH-PERFORMANCE ARINC 801 TERMINI WITH THE VERSATILITY AND FAMILIARITY OF D38999 SERIES III STYLE CONNECTORS MC801 FIBER OPTIC CONNECTORS
More informationR52 Top Commander. Installation and Configuration Guide. 325 Sharon Park Dr. #652. Menlo Park, CA USA (650)
R52 Top Commander Installation and Configuration Guide 325 Sharon Park Dr. #652 Menlo Park, CA 94025 USA (650) 241-1161 www.fes-auto.com R52 Top Commander Installation Guide Page 2 Table of Contents Chapter
More informationUSB Ranger 110/410 User Guide
USB Ranger 110/410 User Guide Featuring ExtremeUSB Technology USB Ranger 110/410 Thank you for purchasing the USB Ranger. Please read this guide thoroughly before installation. This document applies to
More informationInstallation Manual April Opticom Infrared System Model 560 Card Rack
Installation Manual April 2008 Opticom Infrared System Model 560 Card Rack Installation 1 1 About This Manual 1.1 Purpose of Manual This manual provides step-by-step instructions for installing the Opticom
More informationFiber Optic Prism Switch USER S MANUAL
Fiber Optic Prism Switch USER S MANUAL Warranty Newport Corporation warrants this product to be free from defects in material and workmanship for a period of one year from the date of shipment. If found
More informationCrimplok ST* and SC Non-Adhesive Fiber Optic Single & Multi-mode Connectors
Crimplok ST* and SC Non-Adhesive Fiber Optic Single & Multi-mode Connectors Instructions July 2002 78-8073-7660-9-F 1 Contents 1.0 Warnings and Recommendations... 3 2.0 Tool Kit Contents... 4 3.0 Termination...
More informationSGH Cable Actuated Sensor Industrial CANOpen
Cable Actuated Sensor Industrial CANOpen Two Available Stroke Ranges: 0-80 in & 0-120 in. Rugged Polycarbonate Enclosure Simple Installation Compact Design Built for IP67 environments IN STOCK FOR QUICK
More informationPretium Rack-mountable 1U Housing Hardware
revision history Issue Date Reason for Change table of contents STANDARD RECOMMENDED PROCEDURE 003-649 ISSUE 5 JANUARY 2009 PAGE 1 OF 10 Pretium Rack-mountable 1U Housing Hardware p/n 003-649, Issue 5
More informationGB of cache memory per controller to DS4800 controllers with 8 GB of cache memory per controller.
IBM System Storage DS4800 Controller Cache Upgrade Kit Instructions Attention: IBM has renamed some FAStT family products. FAStT EXP100 has been renamed DS4000 EXP100, FAStT EXP700 has been renamed DS4000
More informationED-22 Analog Output Series Magnetic Encoder
SPECIFICATIONS Analog voltage output Low profile Standard industry package size Sleeve bearing The ED-22 series magnetic encoder can be used to replace a conventional potentiometer. This product offers
More informationSecured Series: Hub Plus Kit Single Door Controller Package Installation Manual
Secured Series: Hub Plus Kit Single Door Controller Package Installation Manual This package is designed to simplify the connections to our Secured Series Hub Plus Controller. This will translate into
More informationDESSMANN - FINGERPRINT LOCK
DESSMANN - FINGERPRINT LOCK User Guide V500 & S510 Version 1.5 1 Contents 1 Introduction 3 1.1 Packing List............................................. 3 1.2 Technical Data...........................................
More informationGateway Profile 4 service guide
Gateway Profile 4 service guide Customizing Troubleshooting Contents Replacing Components in Your Gateway Profile 4.................. 1 About this guide.....................................................
More informationUSB Ranger Fiber Optic USB 2.0 Extender. User Guide
USB Ranger 2224 Fiber Optic USB 2.0 Extender User Guide Thank you for purchasing the USB Ranger 2224. Please read this guide thoroughly. This document applies to Part Numbers: 00-00260, 00-00261, 00-00262,
More information3M Indoor Protected Building Entrance Terminal 4788V-QCS Series
The Network of Networks. 3M Indoor Protected Building Entrance Terminal 4788V-QCS Series with 3M Quick Connect System (QCS) 2811 Dry Flame Retardant Block for Field-Terminated Building Cables Instructions
More informationHardware Replacement Guide
Hardware Replacement Guide Types 6491, 8013, 8702, 8706 Types 8716, 8970, 8972, 8976 Types 8980, 8982, 8986, 8992 Types 8994, 9266, 9276, 9278 Types 9282, 9286, 9288, 9374 Types 9378, 9380, 9384, 9628
More informationSR1H Cable Actuated Sensor Industrial CANOpen Output Signal
Cable ctuated Sensor Industrial CNOpen Output Signal Two vailable Stroke Ranges: 0-125 in & 0-175 in. Rugged Polycarbonate Enclosure Simple Installation Designed for Outdoor & IP67 environments IN STOCK
More informationT200 IDENT PRINTER BUDGET THERMAL TRANSFER PRINTER TECHNICAL DATASHEET
T200 IDENT PRINTER BUDGET THERMAL TRANSFER PRINTER TECHNICAL DATASHEET issue 6, May 2015 The T200 Ident printer is a budget thermal transfer printer. Designed to print on a wide range of TE Connectivity
More informationUser Guide for Nokia Image Viewer SU-5
User Guide for Nokia Image Viewer SU-5 9312060 Issue 1 DECLARATION OF CONFORMITY We, NOKIA CORPORATION, declare under our sole responsibility that the product SU-5 is in conformity with the provisions
More informationInstallation Manual. Mounting Instructions Mechanical Mounting. Luminato. Teleste Corporation
Luminato Installation Manual Teleste Corporation Mounting Instructions Mechanical Mounting Luminato Mechanical Installation, agile_59300316, rev0044 Introduction 1 Contents Introduction 4 General... 4
More informationDual Channel LVDT/RVDT Readout/Controller
SPECIFICATIONS Large backlit dual channel display Menu driven setup and calibration 100 to 240 VAC line powered MIN, MAX, TIR, A+B and A-B functions 2.5, 3.3, 5 and 10kHz selectable excitation Analog and
More information3M Indoor Building Entrance Terminal (IBET) 4790V and 4790VL Series
3M Indoor Building Entrance Terminal (IBET) 4790V and 4790VL Series with 3M Quick Connect System (QCS) 2811 Dry Flame-Retardant Block and RJ-11 Test Ports Instructions Underwriters Laboratories (UL 348X)
More informationCOOPER POWER SERIES. Input/Output (I/O) module installation instructions. Voltage Regulators MN225067EN
Voltage Regulators MN225067EN Effective November 2016 Supersedes June 2014 (S225-70-13) COOPER POWER Input/Output (I/O) module installation instructions SERIES DISCLAIMER OF WARRANTIES AND LIMITATION OF
More informationInstructions for SVC-KIT-0020
Kaleidescape, Inc. July 22, 2010 Instructions for SVC-KIT-0020 Title Time to complete 1U Server Power Supply Replacement 1 hour Procedure to complete Locate Parts and Tools Service Kit Parts Power supply
More informationEUROCARD CONNECTORS PER DIN AND IEC
EUROCARD CONNECTORS PER DIN 41612 AND IEC 60603-2 Quick Reference Guide TE Connectivity s (TE) Eurocard two piece connectors offer a reliable, cost effective solution enabling communication across protocols
More informationIMPORTANT PLEASE READ FIRST
TORQ NV USER MANUAL TABLE OF CONTENTS Specifications...2 Components...4 Battery Installation...5 Basic Functions...6 Lockout/Ready Mode...6 Momentary Mode...6 Primary Control...7 Secondary Control...7
More information212iL Rev. 1.1
212iL 1 International Electronics, Inc. 427 Turnpike Street Canton, Massachusetts 02021 212iL (illuminated Luxury) Keypad Single Unit Keypad- Control Installation Manual Features: 120 User Capability Illuminated
More informationWINTOTAL SOFTWARE. Label/Marker Design Package. Technical Datasheet. TTDS-001 Revision 11 - July 2015
Technical Datasheet TTDS-001 Revision 11 - July 2015 WinTotal is a label/marker design package that makes wire marker printing simple in an industrial environment. Running in the familiar Windows environment,
More informationULTRATRAK RM4000 QUICK START GUIDE. Version 1.3
ULTRATRAK RM4000 QUICK START GUIDE Version 1.3 UltraTrak RM4000 Copyright 2002, Promise Technology, Inc. Copyright by Promise Technology, Inc. (Promise Technology). No part of this manual may be reproduced
More informationIndoor Mini Dome. Hardware Manual D91, D92, E91, E92. Ver. 2013/06/14
Indoor Mini Dome Hardware Manual D91, D92, E91, E92 Ver. 2013/06/14 Table of Contents Precautions 3 Safety Instructions... 5 Introduction 6 List of Models... 6 Package Contents... 7 Physical description...
More informationWSP Fiber Optic Cable Cleaning & Inspection WSP Document Template
Fiber Optic Cable Cleaning & Inspection WSP Document Template Copyright Notice Copyright 2002 Windstream Incorporated. All rights reserved. The entire contents of this document are protected under the
More information