Tunable White LED Driver Dual Channel With Selectable Constant Current

Transcription

1 60K Tunable White ED Driver Dual Channel With Selectable Constant Current HER45 + SAM10 or SAM10/FM with HRC-08 Typical Applications The simple interfaces allows cost effective implementation of tunaeble white ED applications outside of central control systems. Using either the remote handset or the common 1-10V and Switch-DIM wall switches, high-end functionality is achieved with realistic budgets on smaller projects. Suitable for ED panels and downlights - insulated terminal cover with cord restraint: Office / Commercial ighting Hotels Classrooms Retail and Display Home office / Domestic lighting Use for retrofit upgrades & new luminaire designs. De-centralised Operation: HER45: 2-Channel 45W maximum fully featured ED driver. Operation from wall switches via the 1-10V and inputs Features >0.93 <0.5W Tunable White Configurable Constant Current (CC) Output via Dip-Switch Active PFC <0.5W 1-10V & Synchronization Thermal Cut-out Protection Short Circuit Protection Over-load Protection } All with Auto-restart Permanent Settings Memory, Protected against oss of Power 5 Year,,000hr Warranty SAM10 or SAM10/FM: Add remote control functionality using one of the plug in recievers HRC-08 SAM10 SAM10/FM Output Configuration Wire Preparation 1200mA 10mA 0mA 0mA 0mA 3mA Warning: Please make sure the correct current is selected before starting the driver! mm 8mm Solid or Stranded wire type mm 2. To make or release the wire from the terminal, use a screwdriver to push down the button. Hytronik ED Drivers 386

2 Technical Data Input Mains Voltage Mains Current Power Factor Max. Efficiency Dielectric Strength eakage Current 220~240VAC /60Hz 0.22~0.2A % Input Output : 00VAC < 0.25mA Power/Current/ 20W/3mA/10~56V 40W/0mA/10~56V 42W/10mA/10~40V Voltage Range 28W/0mA/10~56V 45W/0mA/10~V 40W/1200mA/10~34V Output Environment Safety and EMC Output power handling Output channel function Ripple Current Uout Max. Turn-on Time Operation Temp. Case Temp. (Max.) IP Rating EMC Standard Safety Standard Certifications Channel 1 (CH1) + Channel 2 (CH2) = 45W max. CH1 = white CH2 = White <3% 75V < 0.5s Ta: -20~ IP20 E515, E61547, E , E E ,E62493,E Semko, CB, RCM, CE, EMC Dimensions and Terminals Main body Buzzer Remote connection Dim/tunable selection V CH2 CH1 ED current selection 185 Additional cap for stand alone installation Hytronik ED Drivers

3 Remote Control Receiver Model SAM10 IR receiver 35.9 Cable side entry Cable back entry Model SAM10/FM oading and In-rush Current umber of Drivers Based upon 16A Circuit Breaker Inrush Current (Imax.) 7.2A Type B Pulse Time 100 μs Type C ight brightness and CCT adjust The driver HER45 has 2 independent output channels to tune the white colour and adjust light brightness. The colour temperature and light brightness are controlled either with the remote control (HRC-08) or manually via momentary push-switch and 1-10V output. Remote control and push-switch wiring diagram: ight brightness and CCT adjust by push-switch Dim/Tunable Selection O OFF 1-10V Dim/Tunable Push Dim/Tunable * Brightness adjust: ight intensity can be finely adjusted by long pressing on the push-switch. * CCT adjust: The colour temperature starts tuning after pressing the push-switch three times within 2 seconds. Set the desired colour with a short press of the push-switch. Hytronik ED Drivers 388

4 Remote control and 1-10V wiring diagram: 1-10V + - ight brightness and CCT adjust by 1-10V dimmer Dim/Tunable Selection O OFF 1-10V Dim/Tunable Push Dim/Tunable * Brightness adjust: light intensity can be finely adjusted by rotating the 1-10V dimmer. * CCT adjust: The colour temperature starts tuning after cycling off/on the 1-10V dimmer 3 times within 3 seconds. Set the desired colour by a further off/on cycle. Performance Characteristics EFFICIECY (%) MA 0MA 1200MA PF V 2V 220V % 60% % % % 100% 0.89 % 60% % % % 100% OAD * Typical Efficiency vs oad OAD * Typical Power Factor vs oad Dimming Characteristics Dimming Curve 1-10V Dimming Curve ight output [%] ight output [%] s 1.2s 2.4s 3.6s 4.8s 6s 8.6s 9.8s 11s 12.2s 13.4s 16s 17.2s 18.4s 19.6s 20.8s 22s Time (s) v 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Control voltage (V) 389 Hytronik ED Drivers

5 Dual Output Control Connection to the ED PCB is made for CH1 and CH2 output connections CH1 = white ED array CH2 = white ED array Inner ring cool white (CH1) Outer ring, warm white (CH2) Each channel can supply up to 45W and white balance can be controlled as such: Colour Temperature White eutral White White Power Distribution CH1=45W, CH2=0W CH1=22.5W, CH2=22.5W CH1=0W, CH2=45W inear Colour Tuning Profile Manual Control via Push-DIM White (Min. 20K) eutral (4000K) White (Max. 60K) * Colour Tuning Step 1: Short press (3 times within 2 seconds) Step 2: Short press (>1 second) * On/off control and brightness adjustment Short press (<0.4 second) ote: short press has to be longer than 0.1s, or it will be invalid. ong press (>0.4 second) ight starts tuning Set the desired colour Toggle light on / off Toggle dim light / increase brightness Recommended CCT range Synchronization ong press (>15 seconds) All lights will dim down to minimum then return to % brightness * We recommend the number of drivers connected to a switch does not exceed 25 pieces. The maximum length of the wires from push to driver should be no more than 20 meters. Remote Control HRC-08 Permanent O/OFF function Press button to switch on or switch off the light. CCT Adjust ong press or to adjust the color of the light. means light turns to warm white, while means light turns to cool white. Direct access to 20k, 30k, 40k, 50k are also available on the remote controller. 20% initial 10,000 hrs. uminaires can be overdesigned with 20% lumen the initial 10,000 hours due to the lumen depreciation of ED. Press button first, then press, this 20% output can be saved during the first 10,000 hours accordingly. Press the button to go back to the full output after 10,000 hrs to maintain the total lumen output. Candle Brightness +/-- ong press or to adjust the brightness of the fixture. ote: 1. The buttons of Function, Programme-office, Programme-home, Setting, Hold-time & Detection range are disabled. 2. The buzzer beeps once when the RC signal is successfully received.! Disabled 2xAAA batteries are required to power the remote control. Hytronik ED Drivers 3