KNX USB INTERFACE UIMtp
|
|
- Cameron Porter
- 5 years ago
- Views:
Transcription
1 KNX USB INTERFACE UIMtp TECHNICAL AND APPLICATION DESCRIPTION Author: Peter Hauner Last modification: 13 November Apricum d.o.o. Mažuranićeva 4, Podstrana, Hrvatska Details, modifications and corrections may be subject to change without notice. Apricum gives no warranty for the accuracy of the document. The reproduction, transmission and use of this document or its contents is not permitted without written authority. All rights reserved.
2 1 CONTENTS 1 Contents UIMtp Product Description Operational Description Current Interface of ETS Bus Connection Physical Address Assignment ETS Product Database State of Delivery Technical Drawings Technical Data /
3 2 UIMtp PRODUCT DESCRIPTION The Apricum USB interface UIMtp connects a PC to KNX TP via USB and provides a galvanic isolated bi-directional data connection to the KNX bus. With the ETS or another KNX compatible commissioning tool the UIMtp works as programming interface. Due to HID profile support no specific USB driver is required. The UIMtp also supports the USB suspend mode. The UIMtp establishes access to all bus devices to feature commissioning, addressing, setting parameters, visualization, protocolling, and diagnostic operation. The protocol used for communication between interface and host is the flexible cemi protocol. The connection between KNX and a PC with standard software (like ETS, EITT, also in Raw Frame operating mode) or other software is handled by the FALCON driver. The UIMtp supports long messages (up to 220 byte APDU length) and ensures easy software handling also under operating systems not supported by the FALCON driver (e.g.: Linux). For specific diagnostic applications like EITT the UIMtp supports the "Raw Frame" operating mode. The UIMtp is supplied by both KNX TP and USB. So, no additional external power supply is necessary. Two LEDs are located on the front panel as illustrated below. The LEDs indicate details concerning the bus (connection) state and telegram traffic. LED 1 Bus State USB 2 Bus State KNX TP line A USB connector B KNX TP connector Picture 1: Front view Number LED Colour Explanation / Range 1 2 Bus State USB (+ Telegram Traffic) Bus State KNX TP (+ Telegram Traffic) green USB connection OK / No telegram traffic blinking green Telegram traffic extent indicated by blinking < off > No USB connection green KNX TP connection OK / No telegram traffic blinking green Telegram traffic extent indicated by blinking < off > KNX TP line not connected (or no USB connection) / 7
4 3 OPERATIONAL DESCRIPTION After connecting the UIMtp to the PC the LEDs show the bus connections status. Lightning green means a connection is established. Blinking green indicates the telegram traffic extent. In Microsoft Windows the UIMtp is recognized as HID (Human Interface Device). So, no extra drivers have to be installed or downloaded. In general, network configurations become less time-consuming. The UIMtp s ETS database entries are available for ETS3.0d and upward. The device (dummy application without parameters and without communication objects) can be added to an ETS project as usual. Picture 2: Connection diagram 3.1 CURRENT INTERFACE OF ETS BUS CONNECTION To use the UIMtp as the KNX programming interface in the ETS the UIMtp has to be chosen as the Current Interface. This can be done in the ETS Bus Connections tab and when editing a project, at the bottom line ( Name and state of current connection ) of the ETS window. Picture 3: ETS Bus Connections window 4 /
5 3.2 PHYSICAL ADDRESS ASSIGNMENT The device is supplied with the individual physical address With the ETS the physical address can be assigned to the device by setting the desired address in the Bus Connections window of the ETS. To download the desired physical address the UIMtp has to be chosen as the Current Interface. Then type in the Individual Address and press the Test button. Note: In this document only the term physical address is used. The term physical address means the physical address as well as the individual address. Both terms are used interchangeably by the KNX organisation. 3.3 ETS PRODUCT DATABASE The KNX product database entry (only as ETS dummy application) can be downloaded from our website and the KNX Online Catalog. Picture 4: Apricum USB Interfaces in the ETS Catalog / 7
6 4 STATE OF DELIVERY The UIMtp is delivered with the following default factory settings: General Product KNX USB Interface Application(s) - ETS Name KNX USB Interface UIMtp Physical address TECHNICAL DRAWINGS All dimensions shown here are specified in mm. The device width is 2 modules at 18 mm. Picture 5: Dimension drawings 6 /
7 6 TECHNICAL DATA Warning: Do not connect to 230V Marking/Design UIMtp Current consumption < 25 ma (KNX TP: < 5mA; USB: 20mA) Connections Display elements Control elements - USB (line): USB2.0 connector (Type B) KNX TP line: KNX TP connector (red/black), screwless, for single-core cable Ø mm Bus State USB Bus State KNX TP Mounting Protection type Pollution degree Protection class Overvoltage category Approbation CE Marking Power supply Housing colour Dimensions Weight Device temperature Ambient humidity 35 mm top-hat rail (TH35) according to IEC60715 IP20 according to IEC according to IEC III according to IEC61140 III according to IEC KNX-certified according to ISO/IEC According to low voltage and EMC guidelines Compliance: EN , EN50581, EN60669, EN USB: Safety extra low voltage, 5V DC (SELV) KNX TP: Safety extra low voltage, 21 30V DC (SELV) Plastic PA66 housing grey H = 90 mm, W = 36 mm (2 modules), D = 71 mm Mounting depth = 64 mm 60 g Working temperature: C Storage temperature: C 5 93 %, non-condensing / 7
DOCUMENTATION MECrf TECHNICAL AND APPLICATION DESCRIPTION. Last modification: 24 November 2017
DOCUMENTATION MECrf TECHNICAL AND APPLICATION DESCRIPTION Author: Peter Hauner Last modification: 24 November 2017 2001-2017 Apricum d.o.o. Mažuranićeva 4, 21312 Podstrana, Hrvatska Details, modifications
More informationUSB RF INTERFACE UIMrf
USB RF INTERFACE UIMrf TECHNICAL AND APPLICATION DESCRIPTION Author: Peter Hauner Last modification: 13 November 2017 2001-2017 TAPKO Technologies GmbH Im Gewerbepark A15, 93059 Regensburg, Germany Details,
More informationDOCUMENTATION UIMip TECHNICAL AND APPLICATION DESCRIPTION. Last modification: 8 September 2017
DOCUMENTATION UIMip TECHNICAL AND APPLICATION DESCRIPTION Author: Peter Hauner Last modification: 8 September 2017 2001-2017 Apricum d.o.o. Mažuranićeva 4, 21312 Podstrana, Hrvatska Details, modifications
More informationDOCUMENTATION UIMip. Authors: Manouchehr Ghahramanian Golzar, Peter Hauner. Last Modification:
DOCUMENTATION UIMip TECHNICAL AND APPLICATION DESCRIPTION Authors: Manouchehr Ghahramanian Golzar, Peter Hauner Last Modification: 2017-03-02 2001-2017 Apricum d.o.o. Mažuranićeva 4, 21312 Podstrana, Hrvatska
More informationCU-DIN USB KNX EC
CU-DIN USB KNX EC10430541 MA00653301 Table of contents 1 Description...2 2 Safety instructions...3 3 Dimension drawings...4 4 Technical data...5 5 Product disposal...6 6 ESYLUX manufacturer s guarantee...6
More informationLinienkoppler S KNX. Line coupler S KNX. Line coupler S KNX Status: March 16 (Subject to change) Page 1 of 29
Linienkoppler S KNX Line coupler S KNX Line coupler S KNX 9070880 Status: March 16 (Subject to change) Page 1 of 29 KNX Contents Contents Page 1 General... 3 1.1 Using the product manual... 3 1.1.1 Structure
More informationABB i-bus KNX Analogue Actuator, 4-fold, MDRC, 0-10 V, 0-20 ma AA/S 4.1.2, 2CDG110202R0011
Technical Data 2CDC505168D0201 ABB i-bus KNX Product description The Analogue Actuator converts telegrams received via KNX into analog output signals. The device has four outputs. The analog outputs can
More informationABB i-bus KNX IP Router, MDRC IPR/S 3.1.1, 2CDG110175R0011
Technical Data 2CDC502086D0201 Product description IP Router 3.1.1 is the interface between KNX installations and IP networks. It can be used as a line coupler or area coupler and can utilize the local
More informationContents 1. Summary
Guangzhou Video-star Electronics Industrial Co., Ltd K-BUS R KNX IP Router User manual-ver.1 BNIPR-00/00.1 KNX/EIB Intelligent Installation Systems Contents 1. Summary------------------------------------------------------------------------------------------------------------------------------
More informationEAE KNX IP Router Product Manual IPR100 (sayfa düzeni ve foto düzenlemesi gerekli)
Product Manual IPR100 (sayfa düzeni ve foto düzenlemesi gerekli) EAE Technology www.eaetechnology.com CONTENTS 1 General...3 1.1 Communication objects...4 1.2 IPR100 as programming interface...4 1.3 Tunnelling...4
More informationProduct and Application Description
Technical Product-Information Product and Application Description The IP Gateway KNX-BACnet N 143 is is a DIN rail mounted device connecting a KNX installation with a system using BACnet/IP communication.
More informationLine Coupler, MDRC LK/S 3.1, GH Q R0001
, GH Q605 0067 000 The coupler can be used as a line The coupler is installed in the distribution board on the data rail of the coupler or a backbone coupler. CDC 07 0 F000 As a line coupler, it links
More informationABB i-bus KNX Analogue Input, 4-fold, MDRC AE/S , 2CDG110190R0011
Technical Data 2CDC504084D0201 ABB i-bus KNX Product description The device is used to record analogue data. Four conventional sensors can be connected to the device. The connection to the bus is established
More informationPush Button Interface UP 220D31
Product and Applications Description Application programs UP 220/31 07 B0 S4 On-off-toggle/Dim/Shu/Value 982203 The push button interface is a binary input and output devices for installation in in-wall
More informationABB i-bus KNX Logic Controller ABA/S 1.2.1, 2CDG110192R0011
Technical data 2CDC509078D0201 ABB i-bus KNX Product description The device provides extensive logic functions. The logic is defined via a graphic editor integrated in the ETS. Up to 3,000 logic gates
More informationProduct and Applications Description. Application programs. instabus EIB Technical Product Information. February 2012
Product and Applications Description Application programs UP 220/31 07 B0 S4 On-off-toggle/Dim/Shu/Value 982201 The push button interface UP 220/31 is a binary input and output devices for installation
More informationProduct and Applications Description
IP N146/02 Product and Applications Description The IP N146/02 is a DIN rail mounted device. The device implements the KNXnet/IP standard and connects KNX/EIB lines via data networks using the Internet
More informationABB i-bus KNX Switch Actuator, x-fold, 6 A, MDRC SA/S x.6.1.1, 2CDG x R0011
, 2CDG 110 15x R0011 SA/S 12.6.1.1 2CDC 071 033 S0012 The 6 A Switch actuators are modular installation devices in Pro M Design for installation in the distribution board. The devices are suitable for
More informationABB i-bus KNX AC/S Application Controller
ABB i-bus KNX AC/S 1.2.1 Application Controller Description of product Automation controller with pre-defined automation modules for comprehensive heating, ventilation and air conditioning automation (HVAC
More informationABB i-bus KNX Switch Actuator, x-fold, 16 A, MDRC SA/S x , 2TAZ710xx1R2161
Technical Data 9AKK107045A4913 ABB i-bus KNX Product description Switch Actuators SA/S x.16.2.1, 16 A are modular installation devices in ProM design for installation in the distribution board. They are
More informationProduct and functional description
Product and functional description The UP 525/13 Universal Dimmer is a KNX device with one dimmer output. The device is installed in a flushmount wall box (60 mm Ø, depth 60 mm) or an installation box.
More informationProduct and functional description
Product and functional description Connection example The universal dimmer main module N 528/31 is an installation device for DIN-rail mounting, with N-system dimensions. It is designed for lighting control,
More informationABB i-bus KNX Switch Actuator, x-fold, 10 A, MDRC SA/S x , 2CDG11015xR0011
Technical Data 2CDC505054D0205 ABB i-bus KNX Product description Switch Actuators SA/S x.6.2.1, 10 A are modular installation devices in ProM design for installation in the distribution board. They are
More informationOperating and mounting instructions
General Usage IPAS DALI Gateways bring together the crossfunctional KNX installation bus and the lighting control specific DALI-Bus (IEC 60929). Lights with cost-effective, digital DALI ECGs can therefore
More informationProduct and functional description
Product and functional description The RS 525/23 Universal Dimmer is a KNX device with one dimmer output. The device is installed in an AP 118 Control Module Box or an AP 641 Room Control Box. The bus
More informationProduct and Applications Description. Application Programs. Example of Operation. Installation Instructions. load circuit AC 230/400V L1 L2 L3 N
Product and Applications Description Application Programs 20 A4 Binary 906401 4 binary outputs 1 status request available for each output 1 relation can be set allows 1 positive drive for each output initial
More informationProduct and functional description. Application Program. instabus EIB Technical product information. April (6 x AC 230 V / 0,05 A)
Product and functional description also functions if the bus cable is not connected or if the bus communication fails. After a long push button action (> 2 s), the other valve group is selected. The yellow
More informationABB i-bus KNX Switch Actuator, Current Detection, x-fold, 16/20 A, C-Load, MDRC SA/S x , 2CDG1101xxR0011
Technical Data 2CDC505082D0203 ABB i-bus KNX Product description Switch Actuators SA/S x.16.6.1, 16/20 A are modular installation devices in ProM design for installation in the distribution board. They
More informationProduct and Applications Description. Example of Operation. Installation Instructions WARNING. Note. Application Programs
Product and Applications Description Example of Operation dimmer UP 525/11 load circuit AC 230 V L1 N The dimmer UP 525/11 is a dimming actuator for mounting in box mounts (a.o. 60 mm Ø, 60 mm depth).
More informationInstaller Manual Line/Field coupler KNX standard, installation on DIN rail (60715 TH35)
Installer Manual Line/Field coupler KNX standard, installation on DIN rail (60715 TH35) Contents 1. Product description 4 2. KNX topology 4 3. Device frontend 5 3.1 Installation example 6 4. Operational
More informationDELTA i-system wall switch single UP 221/2 5WG AB_2
DELTA i-system wall switch single UP 221/2 5WG1 221-2AB_2 UP 221/3,with status LED 5WG1 221-2AB_3 wall switch double UP 222/2, 5WG1 222-2AB_2 UP 222/3,with status LED 5WG1 222-2AB_3 wall switch triple
More informationProduct and functional description
Product and functional description Connection example The universal dimmer submodule N 528/41 is an installation device for DIN-rail mounting, with N-system dimensions. It is designed for lighting control,
More informationProduct and Applications Description. Application Programs. Note. instabus EIB Technical Product Information. June 2005
Product and Applications Description Application Programs The application programs of the dimmer UP 525/01 consist of two elements: the actuating and the sensor program element. The tasks actuating program
More informationDevice technology. Supply Bus voltage V DC. Current consumption via bus. Accuracy in the range 300 1,000 ppm 1,000 2,000 ppm 2,000 5,000 ppm
2 2.1 Air Quality Sensor LGS/A 1.1 The ABB i-bus KNX Air Quality Sensor 1.1 is a combined sensor for CO 2, temperature and humidity measurement (relative humidity). Three independent thresholds can be
More informationFan Coil Actuator, MDRC FCA/S 1.1M, 2CDG R0011
, 2CDG 110 084 R0011 2CDC 071 112 F0008 The Fan Coil Actuator is a modular installation device (MDRC) in prom design. It is intended for installation in the distribution board on 35 mm mounting rails.
More informationDELTA profil wall switch, single UP 241/2 5WG AB_2
UP 241/2 5WG1 241-2AB_2 UP 241/3,with status LED 5WG1 241-2AB_3 UP 243/2 5WG1 243-2AB_2 UP 243/3,with status LED 5WG1 243-2AB_3 UP 245/2 5WG1 245-2AB_2 UP 245/3,with status LED 5WG1 245-2AB_3 UP 245/4,with
More informationProduct and functional description
Product and functional description The RS 520/23 shutter / blind actuator is a KNX device with one relay output. The device is installed in an AP 118 Control Module Box or an AP 641 Room Control Box. The
More informationUSB-KNX Interface OCI702. USB-KNX interface with cables and service bag
USB-KNX Interface OCI702 USB-KNX interface with cables and service bag The USB-KNX interface OCI702 serves to provide a USB-KNX connection to access tools from a Microsoft Windows PC to a KNX network or
More informationPRODUCT MANUAL. ABB i-bus KNX SV/S KNX-Power Supplies
PRODUCT MANUAL ABB i-bus KNX SV/S KNX-Power Supplies Contents Contents side 1 General... 3 1.1 Using the product manual...3 1.1.1 Structure of the product manual...4 1.1.2 Notes...4 1.2 Product and functional
More informationProduct and Applications Description. Note. Example of Operation. Installation Instructions. Application Programs WARNING
Product and Applications Description Note If the application program is not loaded completely by the ETS, you had better interrupt the 24 V voltage supply of the I/O-module during the loading interval.
More informationABB i-bus KNX HCC/S Heating/cooling circuit controller
ABB i-bus KNX HCC/S 2.2.1.1 Heating/cooling circuit controller Description of product The device is a modular DIN rail component (MDRC) in pro M design. It is intended for installation in distribution
More informationABB i-bus KNX BCI/S Boiler/Chiller Interface
ABB i-bus KNX BCI/S 1.1.1 Boiler/Chiller Interface Description of product The boiler/chiller interface is a modular DIN rail component that acts as an interface to the heating/cooling system generator.
More informationKSR-01IP KNX IP Router Instruction manual
KSR-01IP KNX IP Router Instruction manual KSR-01IP Instruction Manual Content 1.Product Description... 1 1.1 Front Panel... 1 1.2 LED Indication... 2 1.3 Commissioning... 2 1.4 Feature Summary... 3 2.KNXnet/IP...
More informationABB i-bus KNX DALI Light Controller, 8-fold, MDRC DLR/S M, 2CDG110101R0011
Technical data 2CDC507101D0202 ABB i-bus KNX Product description The ABB i-bus KNX DALI Light Controller DLR/S 8.16.1M is a KNX modular installation device (MDRC) in ProM design for installation in the
More informationLine Coupler, MDRC LK/S 2.1, GH Q R0001
, GH Q605 0019 R0001 The coupler can be used as a line In the distribution board the coupler is coupler or as an area coupler. Used as installed on the secondary line of the a line coupler it joins up
More informationSee instructions to download and install the latest version of LinkBoxLON and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationArticle No. 6GK59230PS003AA2 6GK59240PS001AA2 Product Name. Power Supply SCALANCE PS924 PoE Input: 120/230V AC; Output: 54V/ 1.
Product Name Type of power supply Electrical data Input Waveform of the input Supply Power Supply SCALANCE PS924 PoE Input: 120/230V AC; Output: 54V/ 1.6A DC; NEC Class 2 single-phase AC Power Supply SCALANCE
More informationDatasheet RCUXXYY EAE KNX Room Control Unit RCUXXYY DT R1.0. General Description. EAE Technology Page 1/10
General Description Room Control Unit RCU Series are designed as an all in one product for different room layouts such as apartments, hotel rooms, hospitals and residences. Available versions of EAE RCU
More informationSwitching Actuators N530, 6AX Switching Actuators N532, 10AX Switching Actuators N534, 16/20AX
Gamma instabus Technical Product nformation Switching Actuators N53, 6AX Switching Actuators N532, 1AX Switching Actuators N534, 16/2AX 4x AC 23V 5WG1 53-1DB31 5WG1 532-1DB31 5WG1 534-1DB31 8x AC 23V 5WG1
More informationPCAN-Repeater 2-Channel CAN Repeater with galvanic isolation. User Manual V1.0.0
PCAN-Repeater 2-Channel CAN Repeater with galvanic isolation User Manual V1.0.0 Products taken into account Product Name Model Item Number PCAN-Repeater Industry IPEH-004038 All product names mentioned
More informationCLIMATIX STEQ, STCM DATASHEET FOR CONTROLLING, SWITCHING AND MONITORING FUNCTIONS. POWER SUPPLY RELAY OUTPUTS. Power supply. 4.
CLIMATIX STEQ, STCM DATASHEET FOR CONTROLLING, SWITCHING AND MONITORING FUNCTIONS. 4. Relays Power supply 2. Relays 8. Universal Inputs/ Process Bus (KNX) RS485 (Modbus) Tool (USB) Ethernet Tool (USB)/
More informationSee instructions to download and install the latest version of LinkBoxEIB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationSee instructions to download and install the latest version of LinkBoxEIB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationOperating instructions Evaluation system for flow sensors VS / / 2013
Operating instructions Evaluation system for flow sensors VS3000 7097 / 0 07 / 203 Contents Preliminary note...2 2 Safety instructions...3 3 Function and features... Mounting.... Mounting of the sensors...
More information584 5WG AB_1 DELTA
Product DELTA profil DELTA style DELTA ambiente Display and control unit 5WG1 585-2AB01 pearl grey 5WG1 585-2AB11 titanium white 5WG1 585-2AB21 anthracite 5WG1 585-2AB71 silver 5WG1 585-2AB11 titanium
More informationPush button UP 287, 4 - fold
Product DELTA profil DELTA style Push button 1-fold pearl grey 5WG1 241-2AB01 titanium white 5WG1 285-2AB11 titanium white 5WG1 241-2AB11 basalt black 5WG1 285-2AB21 anthracite 5WG1 241-2AB21 titanium
More informationABB i-bus KNX Weather Unit, 1-fold, MDRC WZ/S , 2CDG110184R0011
Technical Data 2CDC504091D0201 ABB i-bus KNX Product description The Weather Unit WZ/S 1.3.1.2 is used - primarily in residential applications - to record weather data. The Weather Sensor WES/A 3.1 is
More informationWeather station AP 257/51
Gamma instabus Weather station GPS AP 257/61 Weather station AP 257/51 Technical product information 5WG1 257-3AB61 5WG1 257-3AB51 Weather station with sensors to survey temperature, brightness, rain and
More informationProduct and functional description
Product and functional description The instabus / DAI gateway 141 is a KX EIB device with one DAI output to which up to 64 DAI actuators (e.g. DAI ballasts) can be connected to. It is not allowed to connect
More informationPower supply module, bus connection module
s 8 183 8183p01, p02 TX-I/O Power supply module, bus connection module TXS1.12F10 TXS1.EF10 Each I/O row begins with one of these devices TXS1.12F10 power supply module Up to 4 power supply modules can
More informationManual Industry Interfaces
Manual Industry Interfaces W&T Release. Type 0, 0 0, 00 0, 0 0, 0 Industry Interfaces 0/0 by Wiesemann & Theis GmbH Subject to errors and changes: Since we can make mistakes, none of our statements should
More informationIP gateway, MDRC IG/S 1.1, GH Q R0001
, GH Q631 0067 R0001 The IP gateway IG/S is the interface The IP address of the IG/S can be between EIB / KNX installations and IP fixed or received from a DHCP server. CDC 071 130 F0003 networks. Data
More informationABB i-bus KNX Fan Coil Actuator, PWM, MDRC FCA/S , 2CDG110195R0011
Technical data 2CDC508136D0202 ABB i-bus KNX Product description The device is a modular installation device (MDRC) in Pro M design. It is intended for installation in distribution boards on 35 mm mounting
More informationOperating voltage Maximum
, 2CDG 110 0x R0011 2CDC 071 023 F000 The ABB i-bus Light Controllers, (x = 2 or 4) are KNX modular installation devices in ProM Design for installation in the distribution board on 35 mm mounting rails.
More informationSee instructions to download and install the latest version of LinkBoxMB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationSee instructions to download and install the latest version of LinkBoxEIB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationCU port USB 2.0 hub. Version: 1.1 Date:
CU8004-0000 4 port USB 2.0 hub Version: 1.1 Date: 2006-08-11 Table of Contents Table of Contents 1 Foreword 1 1.1 Notes on the documentation 1 1.1.1 Liability Conditions 1 1.1.2 Conditions of delivery
More informationinstabus KNX / EIB product documentation
Page: 1 of 21 System Product name: (R2) Design: REG (rail-mounted ) Article-no.: J: IPR 100 REG ETS search System s / / path: Issue: 05.03.2010 Functional description: This describes the with the release
More informationENGLISH DATALOGGER V2 ANALYZE. CONTROL. OPTIMIZE.
ENGLISH DATALOGGER V2 ANALYZE. CONTROL. OPTIMIZE. DATALOGGER V2 ANALYZE. CONTROL. OPTIMIZE. Included KNX IP router functionality NEW in DATALOGGER: New, more powerful hardware The DATALOGGER V2 is a powerful
More informationProduct and Application Description
Technical Product - Information Product and Application Description The room temperature controller UP 237K and UP 252K are available in the following colors, matching the design of the wall switch design
More informationUSER MANUAL CU-DIN IPRT KNX EC MA
CU-DIN IPRT KNX EC10430527 MA00653502 Table of contents 1 Description...3 2 Safety instructions...4 3 Product Funtion...5 3.1 Communication objects... 5 3.2 CU-DIN IPRT KNX as programming interface...
More informationWeather station GPS AP 257/61 Weather station AP 257/51
Gamma instabus Weather station GPS AP 257/61 Weather station AP 257/51 Technical product information 5WG1 257-3AB61 5WG1 257-3AB51 Weather station with sensors to survey temperature, brightness, rain and
More informationApplication description for the KNXnet/IP Interface Web
Contents 1. General 1. General... 1 1.1 Basic information about the KNX/EIB BUS... 1 1.2 Application versions......1 1.3 Symbols...1 1.4 Function description... 2 1.5 Short description of the function
More informationControl unit for lux control, MDRC Type: SL/S 50.1, GH Q R0001
SK 0012 B 98 The control unit is a DIN rail mounted device for insertion in the distribution board. It is used to control digitally dimmable electronic ballast devices or transformers via the EIB. In a
More informationCommunication module to connect M-bus devices to POL6xx.xxx controllers.
s 3 936 Climatix TM Climatix communication M-Bus module POL907.00/xxx Communication module to connect M-bus devices to POL6xx.xxx controllers. The POL907.00/xxx communication module offers the following
More informationOCI Service Tool. Siemens Building Technologies HVAC Products. ACS plant operating software and OCI700 service interface
5 655 Service Tool ACS plant operating software and OCI700 service interface OCI7001 Service tool for commissioning and the diagnosis of HVAC controllers of the Synco, SIGMAGYR and ALBATROS ranges Use
More informationInstallation Instructions
Installation Instructions (Cat. No. 1794-PS1) 1 2 3 4 5 7 6 Component Identification 1 Supply module 1794-PS1 2 Indicator 3 120/230V ac ground 4 120/230V ac common L2/N connections 5 120/230V ac power
More informationGS Dupline Profinet Gateway. Benefits. Description
Dupline Profinet Gateway Benefits Profinet gateway with the function as a slave Up to 7 master generators can be connected via the HS RS485 bus (side connector) All Dupline signals from the master generators
More informationABB i-bus KNX Application Unit Time ABZ/S 2.1 Product Manual
ABB i-bus KNX Application Unit Time ABZ/S 2.1 Product Manual ABZ/S, Application Unit Time Contents Page 1 General 6 1.1 Product and functional description...7 2 Device technology 8 2.1 Technical data...8
More information252F 5WG FB_1 DELTA
Product DELTA i-system DELTA profil Fan-Coil Unit Operator Panels Hotel titanium white 5WG1 237-2FB11 pearl grey 5WG1 252-2FB01 carbon metallic 5WG1 237-2FB21 titanium white 5WG1 252-2FB11 aluminum metallic
More informationPower Supply System KNX PS640-IP
Power Supply System KNX PS640-IP with Ethernet Interface Installation and Adjustment Elsner Elektronik GmbH Steuerungs- und Automatisierungstechnik Herdweg 7 D-75391 Gechingen Germany Phone: +49 (0) 70
More informationEAE KNX Switch Actuator
EAE KNX Switch Actuator Order Number: 48002 Content 1 General... 2 2 Device Technology... 3 2.1 Connection Diagram... 3 2.2 Technical Data... 4 3 Communication Object Table... 5 4 Parameters... 6 4.1 Main
More informationOperating instructions. Switching amplifier DN0210 DN / / 2015
Operating instructions Switching amplifier DN0210 DN0220 UK 80011079 / 00 01 / 2015 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5
More informationOperating instructions. Standstill monitor A / / 2011
Operating instructions Standstill monitor A300 UK 1 2 3 4 5 6 7 8 7390337 / 01 02 / 2011 1 2 3 4 5 6 7 8 switchpoint min max pulse/min power Made in Germany ifm electronic gmbh D 45127 Essen func. I II
More informationCU USB-Extender-Rx (USB and DVI Extender) Version: 0.3 Date:
CU8860-0000 USB-Extender-Rx (USB and DVI Extender) Version: 0.3 Date: 2006-02-20 Table of Contents Table of Contents 1 Foreword 1 1.1 Notes on the documentation 1 1.1.1 Liability Conditions 1 1.1.2 Conditions
More informationABB i-bus KNX Binary Inputs BE/S Product Manual
kg ABB i-bus KNX Binary Inputs BE/S Product Manual Contents Contents Page 1 General 5 1.1 Using the product manual...5 1.1.1 Structure of the product manual...5 1.1.2 s...6 1.2 Product and functional
More informationAS-i Safety Relay Output Module with Diagnostic Slave
AS-i Safety Relay Output Module with Diagnostic Slave User Manual...supports the requirements for AS-i Safety up to SIL3 Revision date: 2016-03-9 Subject to modifications without notice. Generally, this
More informationSiemens Spares. RL 513D23 Switching actuator (relay), 3 x 6A. Technical Product Information
Gamma instabus Technical Product Information RL 513D23 Switching actuator (relay), 3 x 6A 5WG1 513-4DB23 Switching actuator for independent switching of three lighting luminaire groups or other loads one
More information1 Safety instructions. 2 Device components. 3 Function. IC00P01DAL - DALI gateway. DALI gateway. Operating instructions
DALI gateway Operating instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons. Serious injuries, fire or property damage possible. Please
More informationInterface AP 146 5WG AB01 for Ethernet-UDP/IP. EIB Device. EIB Device. EIB Device
Product and Applications Description With the ETS (EIB Tool Software) the application program is selected, its parameters and addresses are assigned appropriately, and downloaded to the interface AP 146.
More informationFL SWITCH SFN 5TX. Extract from the online catalog. Order No.:
Extract from the online catalog FL SWITCH SFN 5TX Order No.: 2891152 Ethernet switch, 5 TP RJ45 ports, automatic detection of data transmission rate of 10 or 100 mbps (RJ45), autocrossing function Commercial
More informationPCAN-Repeater DR CAN Repeater for the Decoupling of Bus Segments. User Manual. Document version ( )
PCAN-Repeater DR CAN Repeater for the Decoupling of Bus Segments User Manual Document version 2.0.0 (2018-02-20) Relevant products Product Name Model Part number PCAN-Repeater DR Industry IPEH-004038 PCAN
More informationABB i-bus EIB. Shutter Actuator, 2-fold, 6 A, 230 VAC, MDRC JA/S 2.6.1, GH Q R0111
, GH Q31 0022 R0111 The 2-fold shutter actuator is a DIN rail mounted device for insertion in the distribution board. It is connected to the EIB via a bus connecting terminal. It is used to control two
More informationTRIO-PS/1AC/24DC/20. Extract from the online catalog. Order No.:
Extract from the online catalog TRIO-PS/1AC/24DC/20 Order No.: 2866381 DIN rail power supply unit, primary-switched mode, 1-phase, output: 24 V DC / 20 A Commercial data EAN 4046356046664 Pack 1 pcs. Customs
More informationTXM1.8T. Triac module Used for Thermic and motor-driven actuators (AC 24 V) TX-I/O
s 8 179 8179p01 TX-I/O Triac module sed for Thermic and motor-driven actuators (AC 24 V) AC 24 V-controlled devices TXM1.8T 8 triac outputs (AC 24 V), configured individually for: Permanent contact Three-point
More informationResistance measuring module
s 8 176 8176P01 TX-I/O Resistance measuring module TXM1.8P 8 inputs with LED signal / fault display. 8 resistance measuring inputs with individual configuration of resistance or temperature measurement.
More informationPCAN-Repeater DR CAN Repeater for the Decoupling of Bus Segments. User Manual V1.1.0
PCAN-Repeater DR CAN Repeater for the Decoupling of Bus Segments User Manual V1.1.0 Products taken into account Product Name Model Part Number PCAN-Repeater DR Industry IPEH-004038 All product names mentioned
More informationTXM1.8RB. TX-I/O Blinds module
s 8 178 8178p01 TX-I/O Blinds module TXM1.8RB 8 non-floating relay outputs for... 4 blinds motors with 2 end switches, or 2 blinds motors with 3 end switches, or 2 blinds motors with 2 end switches + 1
More informationProduct and Function Description
Product and Function Description and the LED display. The touchscreen can be used to select from up to 6 languages for the display of texts and messages. The room temperature controller integrated in Contouch
More informationEnglish. Operating manual. Universal transmitter UT125. Save for later reference. Companies / brands of GHM
English Operating manual Universal transmitter UT125 Companies / brands of GHM www.ghm-messtechnik.de Save for later reference. Table of contents page 1. Intended use (areas of application)... 3 1.1 Safety
More information