XT XGA TFT NEMA 4/12 Flat Panel Monitor. User s Guide

Transcription

1 XT XGA TFT NEMA 4/12 Flat Panel Monitor User s Guide (C) (was document no. 920A0011 version 1.0), revised 07/01 Viewtronix

2 Viewtronix reserves the right to make changes in specifications described herein at any time without notice in order to improve design and reliability. Viewtronix does not assume any responsibility for the use of any circuitry described; no circuit patent licenses are implied. Viewtronix assumes no responsibility for damage caused by misuse or improper use of its products. WARRANTY Viewtronix warrants to Customer that the Products will be free from defects in material and workmanship under normal use and service for a period of one year from date of invoice. Customer s exclusive remedy for breach of this warranty is that Viewtronix will either (i) repair or replace, at its option, any Product which fails during the warranty period because of such defect (if Customer promptly reported the failure to Viewtronix in writing) or, (ii) if Viewtronix is unable to repair or replace, Viewtronix will refund the purchase price of the Product upon its return to Viewtronix. This warranty does not apply to any Product which has been subjected to misuse, abnormal service or handling, or which has been altered or modified in design or construction, or which has been serviced by anyone other than Viewtronix. The warranty set forth herein is in lieu of, and exclusive of, all other warranties, express or implied. Document No (C) (was 920A0011 version 1.0) Released 07/01 2

3 Table of Contents WARRANTY...2 Table of Contents...3 Introduction...4 Video Modes Supported...4 Specifications...5 Front and Side View of Monitor...6 Installation of Monitor...6 Cutout Pattern for Monitor...7 Mode and Image Adjustment...7 Front Panel Controls...8 On Screen Display (OSD) Functions...9 Main OSD menu...9 Image Adjust Submenu...9 OSD Submenu...10 System Info Submenu...10 Extended Submenu...11 Direct Access 1 & 2 Submenu...11 Language Submenu...11 Back Light Replacement Procedure...12 VGA Input Connector Pin Out...13 Appendix A - Dimensions and Weight of XT1502-ENC

4 Introduction The XT1502 is a high performance 15.0 XGA (1024 x 768) TFT industrial flat panel monitors for use in NEMA 4 and NEMA 12 applications. Graphics and text can be displayed on the monitor in up to 262,144 colors and in the modes listed below. When the monitor is being driven in modes other than XGA, it will automatically expand the image and center it on the LCD. The unit is fully self-contained needing only to be panel mounted in an appropriate enclosure and connected to 120/240 VAC and a VGA source. The monitor features a bright 200-nit LCD display and conveniently located front panel controls with on screen menus for easy set up and adjustment. The XT1502 is designed to provide tool free access for quick back light replacement and cleaning. Both models are available with optional integrated analog resistive touch screens, 304 stainless steel bezels and VDC input. Video Modes Supported MODE HORIZONTAL SYNC RATE KHz VERTICAL SYNC RATE Hz DOT FREQUENCY MHz EXPANSION FACTOR VESA VGA 640 x 480 INDUSTRY TEXT 720 x 400 VESA SVGA 800 x 600 VESA XGA 1024 x 768 POWER MAC 640 x 480 POWER MAC 832 x 624 POWER MAC 1024 x

5 Specifications DISPLAY Parameter Specification Display Size 15.0 Diagonal Active Area (H) x 8.98 (V) Pixel Format 1024 (H) x 768 (V) Pixels (1 Pixel = R + G + B Dots) Brightness 150 Nit Minimum, 200 Nit Typical Contrast Ratio >150:1 Number Colors 6 bits / color (262,144 Total Colors) PHYSICAL PARAMETER SPECIFICATION Monitor Outside Dimensions (H) x (W) x 3.25 (D) Monitor Weight 16.5 Pounds Operating Temperature 0 ~ 50 Degrees Centigrade Storage Temperature -25 ~ 75 Degrees Centigrade Relative Humidity 5% ~ 90%, Non-condensing Operating Vibration 5 ~ 500 Hz, 1G Operating Shock 15G for 11ms Operating Altitude 40,000 Feet Above Sea Level ELECTRICAL PARAMETER SPECIFICATION Input Voltage Input Power 90 ~ 264 VAC, 47 ~ 440 Hz 35 W COMPLIANCE Parameter Specification NEMA Rating EMC Safety NEMA 4/12 From front when properly installed in an enclosure. FCC Part 15, Class A / Industry Canada ICES-003 Issue 2, Rev. 1 / EN , 4-3, 4-4 / EMC Directive 89/336/EEC (Pending) UL-1950 / CUL/CSA M93/ EN60950 / Low Voltage Directive 73/23/EEC (Pending) 5

6 I Front and Side View of Monitor Viewtronix 13.50" O 16.50" 3.00" Installation of Monitor This monitor is intended to be mounted in and used where NEMA 4 and NEMA 12 type enclosures are employed. When mounted properly, the monitor meets or exceeds the sealing requirements set forth in the NEMA 4 and NEMA 12 specifications. The monitor uses U -shaped clips and a special gasket to achieve the proper seal. To install the monitor, make a cutout per the diagram below in one of the walls of your NEMA enclosure. Enclosures made of heavier gauge metal work better in that they won t deform or bend as easily when the monitor s sealing gasket is compressed. Next hold the monitor in place while you install the mounting clips. Tighten the clips in a cross pattern. This will help to develop an even pressure on the sealing gasket. Tighten the clips to the point were the back of the monitor s front bezel just begins to contact the front of the NEMA enclosure. DO NOT OVER TIGHTEN AS DAMAGE CAN RESULT IN THE MONITOR CAUSING LOSS OF SEALING INTEGRITY. 6

7 Cutout Pattern for Monitor Mode and Image Adjustment Not all video controllers produce exactly the same video output levels or the same timing. The following procedure can be used to select the desired video mode as well as optimize your monitor s image quality. When adjusting your monitor, the use of video test software such as DisplayMate for Windows by SONERA Technologies can be very beneficial. The XT1502 uses On Screen Programming to make setup and adjustment easy. The menus are selected and the menu items are adjusted using the buttons located on the monitor s front panel. These buttons are enabled or disabled by a rocker switch labeled SET UP located on the side of the monitor. This feature is provided to inhibit tampering once the monitor is in actual use. Turn the SET UP switch to the On position to enable set up and adjustment. The following section describes the functions of the front panel buttons. Before connecting the XT1502to your computer, adjust your desktop display settings to the following: Colors: 256 Vertical Refresh: 60Hz Resolution: 1024 x 768 Monitor Type: Viewsonic 15 Once the monitor is powered up press the menu button. After the On Screen Display (OSD) menu appears select the Auto Setup function by scrolling down using the button a then activate this function by pressing the button. The monitor will automatically adjust to the incoming video signal. Now select the Tuning function and fine-tune the image using the and buttons. Finally, set the brightness and contrast settings to your individual preference. 7

8 Front Panel Controls INCREASE - INCREASES THE VALUE OF THE SELECTED MENU ITEM ALSO INCREASES CONTRAST DECREASE - DECREASES THE VALUE OF THE SELECTED MENU ITEM ALSO DECREASES CONTRAST SELECT DOWN - MOVES THE SELECTED MENU ITEM DOWN TO THE NEXT ITEM ALSO INCREASES BRIGHTNESS SELECT UP - MOVES THE SELECTED MENU ITEM UP TO THE NEXT ITEM ALSO DECREASES BRIGHTNESS MENU - TURNS ON SCREEN DISPLAY MENU ON OR OFF POWER ON LED 8

9 On Screen Display (OSD) Functions Pressing the menu button on the front of the monitor activate the OSD which displays the following menu items. Main OSD menu Brightness Increase/decrease panel brightness level Press or (- >>>>>>>>>>>>>>> + nnn), range: 0 to 256 Contrast Increase/decrease panel contrast level Press or (- >>>>>>>>>>>>>>> + nnn), range: 0 to 210 Tuning Fine-tune the data sampling position (phase). (Adjust display quality) Press or (- >>>>>>>>>>>>>>> + nn), range: 0 to 11 Auto Set Up Automatically adjust monitor (e.g. positions, size, tuning etc.) Press to activate auto setup Image Adjust (Note 1.) Turns on the Image Adjust submenu Pressing turns on the Image Adjust menu OSD Menu Turns on the OSD submenu Pressing turns on the OSD menu System Info Turns on the System Information submenu (Shows board information) Pressing turns on the System Information menu Extended Menu Turns on the Extended Menu Pressing turns off the OSD menu Exit Menu Turn off the OSD menu Pressing turns off the OSD menu Note 1. Indicates there are submenus associated with this menu selection. Image Adjust Submenu Image Horizontal Position Image Vertical Position Image Horizontal Size Sharpness Move the image position horizontally Press or (- >>>>>>>>>>>>>>> + nn), range: 0 to 58 Move the image position vertically Press or (- >>>>>>>>>>>>>>> + nn), range: 0 to 56 Change the image width horizontally Press or (- >>>>>>>>>>>>>>> + nnnn), range: 1318 to 1358 Adjust sharpness level Press or (- >>>>>>>>>>>>>>> + n), range: 0 to 3 9

10 Red Green Blue Back Adjust red color level Press or (- >>>>>>>>>>>>>>> + nn), range: 0 to 27 Adjust green color level Press or (- >>>>>>>>>>>>>>> + nn), range: 0 to 27 Adjust blue color level Press or (- >>>>>>>>>>>>>>> + nn), range: 0 to 27 Go back to main menu Press to return to the main menu OSD Submenu Menu Horizontal Position Menu Vertical Position Menu Transparency Menu Timeout Menu Auto Save Back Move the OSD horizontally Press or (- >>>>>>>>>>>>>>> + nn), range: 0 to 62 Move the OSD vertically Press or (- >>>>>>>>>>>>>>> + nn), range: 0 to 60 Adjust the transparent level of the OSD menu Press or (- >>>>>>>>>>>>>>> + nn), range: 0 to 3 Set menu time-out period Press or (10/20/30/45/60/cont) sec Set menu auto save Off/On Go back to main menu Press to return to the main menu System Info Submenu Display type Shows display type, e.g. TFT LCD 1024 x 768 Model Shows the model number of the board, e.g. ACL-1024 BIOS version Shows BIOS version, e.g. V0.40 ss.ss-hh.hh Run Time Shows the accumulated running time of the backlight since last reset (Nn Hrs nn Min) Press for 5 seconds to reset counter Back Go back to main menu Press to return to the main menu 10

11 Extended Submenu DOS Text or Graphics Press or (Text/Graphics) Direct Access 1 Turn on direct access table 1. Pressing turns on table 1. Direct Access 2 Turn on direct access table 2. Pressing turns on table 2. Language Select OSD language Pressing turns on the submenu in English Back Go back to main menu Press to return to the main menu Direct Access 1 & 2 Submenu Brightness Contrast Back Define hot keys as brightness level increase/decrease (default) Pressing assigns this function to the hot key set Define hot keys as contrast level increase/decrease (default) Pressing assigns this function to the hot key set Go back to main menu Press to return to the main menu The direct access table 1 and 2 allow the user to define the function of the two sets of adjustment buttons on the front of the monitor when the OSD is not in use. These sets of buttons (, and, ) are hot keys that allow immediate adjustment without needing to access the OSD. Table 1 assigns functions for the and buttons and table 2 assigns functions to the and buttons. Language Submenu English Italiano Francais Espanol Svenska Nederland Deutsche Back Select English display Select Italian display Select French display Select Spanish display Select Swedish display Select Netherlands display Select Dutch display Press to return to the main menu 11

12 Back Light Replacement Procedure This procedure applies to the XT1502 only. After 50,000 hours of typical use, the two lamps used for back lighting in the XT1502 may become dim or burn out. You may return the monitor to Viewtronix for lamp replacement or you can order new lamps and follow the procedure below to install them. TURN THE MONITOR POWER OFF AND DISCONNECT THE LINE CORD! Loosen the two thumbscrews located on the top of the back. The hinges located on the bottom of the monitor allow you to swing open the back. If the unit is equipped with a touch screen, you may want to disconnect its cable. This is a white flat flexible cable that plugs into a five-pin black bulkhead connector located to the left of the LCD. Disconnect the two pairs of back light (pink and white silicone wires on the right upper and lower corner of the LCD) wires from the inverter extension cables. The lamps do not require tools for removal. They are mounted in small plastic holders that slide outward to the right of the LCD. Carefully pull on the pink and white wires to begin removing the lamps. Now slide the new lamps into place. Reconnect the lamp wires to the inverter extension cables. Make sure you carefully tuck the wires under the LCD so they cannot be pinched when closing the back of the monitor. You may now want to clean the LCD and the inside of the monitor s window or touch screen with a slightly damp soft cloth. Carefully close the back remembering to slide the flat flexible touch screen cable behind the LCD. If you previously disconnected this cable, you should now reconnect it with pin-1 in the up position, making sure the cable is free of any twists. The lamp replacement procedure is now complete. 12

13 VGA Input Connector Pin Out SIGNAL NAME 15-PIN D-SHELL (FEMALE) Red 1 Green 2 Blue 3 4 GND-Digital 5 GND-Red return 6 GND-Green return 7 GND-Blue return 8 9 GND-Digital Hsync 13 Vsync

14 I O Appendix A - Dimensions and Weight of XT1502-ENC XT1500-ENC FRONT AND BOTTOM VIEW Viewtronix 13.50" 16.50" FRONT PANEL CONTROLS DISABLE SECTION A-A REAR AND SIDE VIEW SECTION B-B PLACES A B VGA 3.15 TOUCH POWER ENTRY A B WEIGHT: 19 LBS 14

15 Xycom Automation, Inc Fax: AT-XYCOM Northern Europe Sales: Southern Europe Sales: Xycom Automation, Inc. All rights reserved. Printed in US. All brand or product names are the property of their respective owners. Specifications may change without notice.