Datasheet. Embedded Storage Solutions. Industrial. CompactFlash Card ECF71 / ECF71-T CFXXXXXRX-FXXXXXXX. 21 Aug 2017

Transcription

1 Embedded Storage Solutions Industrial CompactFlash Card ECF71 / ECF71-T CFXXXXXRX-FXXXXXXX 1

2 Table of Contents 1. DESCRIPTION 4 2. FEATURES WRITE PROTECT FUNCTION INTERFACE DESCRIPTION CARD PIN ASSIGNMENT CARD PIN DESCRIPTION CARD BLOCK DIAGRAM ACCESS SPECIFICATION ATTRIBUTE ACCESS SPECIFICATIONS TASK FILE REGISTER ACCESS SPECIFICATIONS I/O ADDRESS MAP MEMORY ADDRESS MAP TRUE IDE MODE CONFIGURATION REGISTER SPECIFICATION CONFIGURATION OPTION REGISTER (ADDRESS 200H) CONFIGURATION AND STATUS REGISTER (ADDRESS 202H) PIN REPLACEMENT REGISTER (ADDRESS 204H) SOCKET AND COPY REGISTER (ADDRESS 206H) CIS INFORMATION TASK FILE REGISTER SPECIFICATION DATA REGISTER ERROR REGISTER FEATURE REGISTER SECTOR COUNT REGISTER SECTOR NUMBER REGISTER CYLINDER LOW REGISTER CYLINDER HIGHT REGISTER DRIVE HEAD REGISTER STATUS REGISTER ALTERNATE STATUS REGISTER COMMAND REGISTER DEVICE CONTROL REGISTER DRIVE ADDRESS REGISTER ATA COMMAND SET ELECTRICAL SPECIFICATION ABSOLUTE RATINGS RECOMMEND OPERATING CONDITIONS 39 2

3 6.3. DC CHARACTERISTICS 1 ( TA = -40 C TO +85 C, VCC = 3.3V +/- 5%) DC CHARACTERISTICS 2 ( TA = -40 C TO +85 C, VCC = 3.3V +/- 5%) ENVIRONMENT AND RELIABILITY AC CHARACTERISTIC ATTRIBUTE MEMORY READ TIMING CONFIGURATION REGISTER (ATTRIBUTE MEMORY) WRITE TIMING COMMON MEMORY READ TIMING COMMON MEMORY WRITE TIMING I/O READ TIMING I/O WRITE TIMING TRUE IDE PIO MODE READ/WRITE TIMING TRUE IDE MULTIWORD DMA MODE READ/WRITE TIMING ULTRA DMA SIGNAL USAGE IN EACH INTERFACE MODE ULTRA DMA DATA BURST TIMING REQUIREMENTS ULTRA DMA DATA BURST TIMING DESCRIPTIONS ULTRA DMA SENDER AND RECIPIENT IC TIMING REQUIREMENTS ULTRA DMA AC SIGNAL REQUIREMENTS PHYSICAL OUTLINE ORDERING INFORMATION CONTACT INFORMATION 58 3

4 1. Description ECF71 series is CompactFlash Storage Card based on FLASH memory controller technology. This card complies with CompactFlash specification; it is suitable for the usage of data storage memory for PC or other electric equipment and digital still camera. This card is equipped with NAND flash memory. The Host system which is connected to Industrial CompactFlash Storage Card should meet system requirements at minimum. The CFC setting to Fixed or Removable mode will be no any function different or issue. 2. Features Flash memory card capacity support list below: SLC: 128MB / 256MB / 512MB / 1GB / 2GB / 4GB / 8GB CompactFlash specification: CF4.1, PCMCIA ver.2.1 and PC Card ATA ver.2.01 compatible 50pin SMT connector and type I (3.3mm). 3.3V/5V single power supply operation. 3 variations of access mode: Industrial PC and Thin Client. Memory Card Mode. I/O Card Mode. True-IDE Mode. True IDE Mode supports: Ultra DMA Modes: 0, 1, 2, 3, 4, and 5. PIO Modes: 0, 1, 2, 3, 4, 5, and 6. Multi-Word DMA Modes 0, 1, 2, 3 and 4. High reliability based on internal ECC (Error Correcting Code) Function. Wear-leveling support Adjustable delta value Stable delta value by erase count increase Endurance: 100,000 erase/program cycles (SLC flash) Operation Temperature range: Normal Temp: 0 to 70. Storage Temperature range: -40 to 85. Wide-Temp:-40 to 85. Storage Temperature range: -55 to 95. Data Performance Speed: Single Channel: Read: Up to 31 MB/sec, Write: Up to 22 MB/sec(Max.) Dual Channel: Read: Up to 51.6 MB/sec, Write: Up to 34.6/sec(Max.) 4

5 Items Model CH Capacity New ordering P/N Read MB/s Write MB/s ECF71 128MB 1CH 128MB CFC128MR7-F002A ECF71 256MB 1CH 256MB CFC256MR7-F102A ICF (ECF71) ECF71 512MB 1CH 512MB CFC512MR7-F202A ECF71 1GB 1CH 1GB CFC001GR7-F302A ECF71 2GB 2CH 2GB CFC002GR8-F302A ECF71 4GB 2CH 4GB CFC004GR8-F402A ECF71 8GB 2CH 8GB CFC008GR8-F402A Support write protect 2.1. Write protect function. Write-protection CompactFlash card functionality. Include Write Protect function CF Cards is designed with a lock switch which allows users to prevent the CF card from programming, writing, and deleting. All data have been written in the Write Protect function CF cards can be read even the CF cards are Write Protect functioned. If the users would like to avoid anyone to modify or destroy the stored data in the CompactFlash cards, the users can switch-on the Write Protect function mechanism and Write Protect function CompactFlash cards would disable the data access to flash memories from data written in. 5

6 3. Interface Description 3.1. Card pin Assignment 6

7 3.2. Card pin Description 7

8 8

9 9

10 10

11 11

12 3.3. Card Block Diagram 12

13 4. Access specification 4.1. Attribute access specifications When CIS-ROM region or Configuration register region is accessed, read and write operations are executed under the condition of REG = L as follows. That region can be accessed by Byte/Word/Odd-byte modes, which are defined by PC card standard specifications. Attribute Read Access Mode Attribute Write Access Mode Attribute Access Timing Example 13

14 4.2. Task file Register access specifications There are two cases of Task File register mapping, one is mapped I/O address area, the other is mapped Memory address area. Each case of Task File registers read and write operations is executed under the condition as follows. That area can be accessed by Byte/World/Odd Byte modes, which are defined by PC card standard specifications I/O address map Task File Register Read Access Mode (1) Task File Register Write Access Mode (1) Task File Register Access Timing Example (1) 14

15 Memory address map Task File Register Read Access Mode (2) Task File Register Write Access Mode (2) Task File Register Access Timing Example (2) 15

16 True IDE Mode The card can be configured in a True IDE This card is configured in this mode only when the OE input signal is asserted GND by the host. In this True IDE mode Attribute Registers are not accessible from the host. Only I/O operation to the task file and data register is allowed. If this card is configured during power on sequence, data register is accessed in word (16-bit). The card permits 8-bit accessed if the user issues a Set Feature Command to put the device in 8-bit mode. True IDE Mode Read I/O Function True IDE Mode Write I/O Function True IDE Mode I/O Access Timing Example 16

17 4.3. Configuration register specification This card supports four Configuration registers for the purpose of the configuration and observation of this card Configuration Option register (Address 200H) This register is used for the configuration of the card configuration status and for the issuing soft reset to the card. INDEX bit assignment 17

18 Configuration and Status register (Address 202H) This register is used for observing the card state Pin Replacement register (Address 204H) This register is used for providing the signal state of IREQ signal when the card configured I/O card interface. 18

19 Socket and Copy register (Address 206H) This register is used for identification of the card from the other card. Host can read and write this register. This register should be set by host before this card s Configuration Option register set. 19

20 4.4. CIS Information CIS information of Compact Flash Card is defined as follows. 20

21 21

22 22

23 23

24 24

25 25

26 26

27 4.5. Task file register specification There registers are used for reading and writing the storage data in this card. These registers are mapped five types by the configuration of INDEX in Configuration Option register. The decoded addressed are shown as follows. Memory map (INDEX=0) Contiguous I/O map (INDEX=1) Primary map (INDEX=2) 27

28 Secondary I/O map (INDEX=3) True IDE Mode I/O map 28

29 Data register Error register Feature register Sector count register 29

30 Sector number register Cylinder low register Cylinder hight register Drive head register 30

31 4.6. Status register Alternate status register 31

32 Command register 32

33 Device control register Drive Address register 33

34 5. ATA Command Set The following table lists the ATA commands that are supported by the Firmware. 34

35 Identify Device Information of True IDE Mode. 35

36 36

37 Identify Device Information of PCMCIA Mode 37

38 38

39 6. Electrical specification 6.1. Absolute Ratings 6.2. Recommend operating conditions 6.3. DC Characteristics 1 ( Ta = -40 C to +85 C, Vcc = 3.3V +/- 5%) 39

40 6.4. DC Characteristics 2 ( Ta = -40 C to +85 C, Vcc = 3.3V +/- 5%) 6.5. Environment and reliability ITEM Specification Vibration Non-Operating 20G(23~2000Hz) Shock Non-Operating 1,500G Max Relative Humidity Operating : 30 Max.wet bulb temp 8% ~ 98% (non-condensing) Non-Operating : 30 Max.wet bulb temp 8% ~ 98% MTBF Operating : 25 2,000,000 hours Endurance Operating 60,000 erase/program cycles(slc flash) 40

41 7. AC Characteristic 7.1. Attribute Memory Read timing 41

42 7.2. Configuration Register (Attribute Memory) write Timing 42

43 7.3. Common Memory Read Timing 43

44 7.4. Common Memory Write Timing 44

45 7.5. I/O Read Timing 45

46 7.6. I/O Write Timing 46

47 7.7. True IDE PIO Mode Read/Write Timing 47

48 7.8. True IDE Multiword DMA Mode Read/Write Timing 48

49 7.9. Ultra DMA Signal Usage in Each Interface Mode 49

50 7.10. Ultra DMA Data Burst Timing Requirements 50

51 7.11. Ultra DMA Data Burst Timing Descriptions 51

52 7.12. Ultra DMA Sender and Recipient IC Timing Requirements Ultra DMA AC Signal Requirements 52

53 53

54 54

55 55

56 56

57 8. Physical outline 57

58 9. Ordering Information P/N Capacity(Max) Remark CFC128MR7-F002A MB CFC256MR7-F102A MB CFC512MR7-F202A MB CFC001GR7-F302A005 1GB Toshiba SLC Normal-Temp CFC002GR8-F302A005 2GB CFC004GR8-F402A005 4GB CFC008GR8-F402A005 8GB CFI128MR7-F003A MB CFI256MR7-F103A MB CFI512MR7-F203A MB CFI001GR7-F303A005 1GB Toshiba SLC Wide-Temp CFI002GR8-F303A005 2GB CFI004GR8-F403A005 4GB CFI008GR8-F403A005 8GB 10. Contact Information ACPI, a storage business company, specializes in the design and marketing of SSD, EDM, and Industry CF products. For further information, please reach us at the following contact information: ACPI Digital Co., Ltd. TEL: FAX: sales@acpigroup.com Address: 11F.-3, No.186, Jian 1st Rd., Zhonghe Dist., New Taipei City 235, Taiwan (R.O.C.) 58