SB User Manual. Toll Free: Tel: Fax:

Transcription

1 SB 003 User Manual Toll Free: Tel: Fax:

2 Table of Contents Item Checklist CHAPTER INTRODUCTION. Over View 3. Key Feature 3 CHAPTER INSTALLATION INTRODUCTIONS. External s.. Keyboard/Mouse :MKB 5.. VGA 5..3 Power : 6..4 UART, 7..5 USB s 8..6 Floppy Drive 9..7 Parallel Port 9..8 IDE 0..9 IRDA 0..0 FAN (CPU).. Seiral ATA s(sata,). Jumper Setting.. Clear CMOS (JCC).. BIOS Protect:JAV..3 Watchdog Timer Action Jumper setting( JWD)..4 FSB Frequency selection 3..5 Front panel connector(j) 3 CHAPTER 3 SB003 STRUCTURE SHOWN AS BELOW 5 CHAPTER 4 WATCHDOG TIMER SETTING 6

3 Item Checklist: Completely check your package. If you discover damaged or missing items, contact your retailer. CPU CARD User s manual Drivers CD-ROM IDE ribbon cable:ata66 IDE ribbon cable:ata00 Floppy ribbon cable USB ribbon cable with braket Parallel port and COM port ribbon cable with braket COM port ribbon cable with braket 6-pin cable One-Two adapter Bag of jumper caps

4 . Overview Chapter Introduction The SB003 is a full size industrial CPU card with six PCB layers. It utilizes Intel 848P and ICH5 chipset(860 Intel 865PE and ICH5 chipset). It also utilizes one84-pin DDR DIMM (860 two 84-pin DDR DIMM)socket to (860 support two channels)ddr RAMat speed of 66/ 333/400MHz, providing a fully compatible,high performance andcost-effective inductry control platform. The integration of onboard VGA controller, four USB.0 ports,serial ATA give customers an advanced solution at a reasonable price.it provides 400/533/800MHZ host bus speed to support INTEL Pendtium4 Socket478 processors.it also provides advanced feathures such as BIOS-proctect,Watchdog Timer and IRDA.. Key Features Size Full-size PICMG: mm x mm. Microprocessor Supports 478pin Northwood and Prescott processor Up to 3.80GHz and futhre Chipset Intel 848 P/865 PE supports 400/533/800 MHZ FSB supports 66/333/400MHZ DDR ICH5 Supports serial ATA 50MB/S System Bus bandwidth: 3./4./6.4 GB/s Supports Hyper-Threading technology, not support Willamete System memory Provides one 84-pin DDR DIMM socket,not support ECC(860 two84-pin DDR DIMM socket not support ECC). Support DDR 66/333/400 Up to Gbytes(860 Up to Gbytes) support DDr dual channel(860 only) On-board VGA Utilize ATI Radeon 7000 Provide 3/64 Mbytes DDR SDRAM display controller,up to.7gb/s On-board IDE Two Ehanced IDE interface connector, supports four IDE devices. Ultra DMA mode up to 00MB/sec. 3

5 Serial ATA serial ATA interface connector. transmission speed up to 50MB/s Optional features:supports RAID0 or RAID,change ICH5 into ICH5-R. On-board I/O One floppy port supporting up to two 3.5 or 5.5 floppy drives with 360K/70K/.M/.44M/.88M format. Supports two COM connector. Supports one PS/ mouse and one KeyBoard. Supports One parallel connector Supports one IRDA connector. Serical/Parall communicatoin CONNECTOR One IDC 6 Parallel Port COM IDC0 COM IDC0 COM->RS3,COM->RS3. PCI-to-ISA Winbond W8368F+W8369D Advanced features 4 USB ports supported,usb.0 compliant. Supports Windows 98/000/XP software soft-off. Hardware BIOS protection from being attacked by virus such as CIH, by enabling Flash Write Protect in CMOS setup. All I/O ports can be enabled/disabled in the BIOS setup. Watchdog Timer: 3 level timer intervals. Reset BIOS AMIBIOS License 4M bit Flash BIOS Supports Plug&Play,APM. Supports boot from USB device Supports boot from CD-ROM Environmental Temperature: 0 o C to 60 o C. Humidity: 5% to 95%. 4

6 Chapter Installation Instructions. External s.. Keyboard/Mouse ( MKB ) This connector is for the usage of PS/ mouse and keyboard through a one-two adapter. If using a standard AT keyboard, an adapter should be used to suit this connector. Additionally, it provides two expanding PS/ keyboard connectors:(kb/ms) KB MS KB DATA 3 MSDATA 4 VCC 5 6 KB CLK MSCLK KB VCC 3 NC 4 KBDATA 5 KBCLK MS VCC 3 NC 4 MSDATA 5 MSCLK.. VGA The monitor output connector is for output to VGA-compatible device. RED 5 BLUE 9 3 NC 6 NC 0 H-SYNC. 4 SPCLK 3 GREEN 7 NC VGA DDA V-SYNC. 5

7 ..3 Power ()0-pin ATX Power (J) V 6 5V 3.3V 6 3.3V 7 -V PWR-OK 3 8-5V 4 5V 9 5VSB 4 PS-ON 9 5V 5 0 V 5 0 5V ()+V Power Supply (J3) (3) EXT ATX Power (J4) VSB 3 5 PWRCTL# 4 NC 6 SLEEP 6

8 ..4 UART, The serial ports UART, connectors can be connected with serial port devices. You can enable/disable them and choose the IRQ or I/O address in INTEGRATED PERIPHERALS from BIOS SETUP. 9 0 UART 9 0 UART DCD 3 RXD 5 TXD 7 DTR 9 DCD 3 RXD 5 TXD 7 DTR 9 DSR 4 RTS 6 CTS 8 RI 0 DSR 4 RTS 6 CTS 8 RI 0 UART UART..5 USB s You should use two 0-pin cable to connect onboard USB headers and USB devices. 9 0 (USB3,4) 9 0 (USB,) VCC 3 UD0-5 UD UD+ 8 UD- 0 VCC 7

9 ..6 Floppy Drive One floppy port supporting up to two 3.5 or 5.5 floppy drives with 360K/ 70K/.M/.44M/.88M format INDEX 5 WRITED 9 DD SEL 9 6 MOTORE 3 30 READ DATA 3 0 MOTORE0 7 4 WRITE G 3 4 NC 8 DIRECTION 5 3 HEAD SELECT 5 DSEL 9 6 TRACK DD SEL 3 0 STEP 7 34 DISKETTE CH 7 4 DSEL0 8 WRITE P Parallel Port The parallel port connector can be connected to a parallel device. You can enable/disable them and choose the IRQ or I/O address in INTEGRATED PERIPHERALS from BIOS SETUP. 5 6 STB 6 PD4 BUSY 6 INITIALIZE PD0 7 PD5 PAPER EMP TY 7 SELECT 3 PD 8 PD6 3 SELECT PD 9 PD7 4 AUTO FEED PD3 0 ACK 5 ERROR 0 5 8

10 ..8 IDE Connetor(IDE,) Secondary 40 Primary Reset IDE 9 Host Data4 7 Host Data0 5 Host IOR 33 Address 0 Host Data 8 Host Data NC 3 Host Data7 Host Data3 9 7 ROCHRDY 35 Address 0 4 Host Data8 Host Data 0 NC 8 Host ALE 36 Address 3 5 Host Data6 3 Host Data DRQ 9 DACKI 37 Chip Select0 6 Host Data9 4 Host Data Chip Select 7 Host Data5 5 Host Data 3 Host LOW 3 IRQ5 39 Activity 8 Host Data0 6 Host Data4 4 3 NC 40 ()40pin IDE Reset IDE 9 Host Data4 7 Host Data0 5 Host IOR 33 Address 0 Host Data 8 Host Data NC 3 Host Data7 Host Data3 9 7 ROCHRDY 35 Address 0 4 Host Data8 Host Data 0 NC 8 Host ALE 36 Address 3 5 Host Data6 3 Host Data DRQ 9 DACKI 37 Chip Select0 6 Host Data9 4 Host Data Chip Select 7 Host Data5 5 Host Data 3 Host LOW 3 IRQ5 39 Activity 8 Host Data0 6 Host Data4 4 3 NC 40 ()40pin IDE..9 IRDA 5 +5V NC 3 IRTX 4 5 IRRX 9

11 ..0 FAN Connetor(CPU FAN) The fan speeds of CPU FAN can be detected and viewed in PC Health section of the BIOS. 3 +V 3 FANTACH.. Serial ATA (SATA,) SATA SATA TXP 3 TXN 4 5 RXN 6 RXP 7 3. Jumper Setting Jumpers are located on the CPU card, they represent, clear CMOS jumper JCC etc. Pin for all jumpers are located on the side with a thick white line ( Pin ),refer to the CPU card s silkscreen. Jumpers with three pins will be shown as to represent pin & pin connected and ( ) to represent pin & pin3 connected. 0

12 .. Clear CMOS (JCC) If you want to clear CMOS, unplug the AC power supply first, close JCC (pin & pin) once, set JCC back to the normal status with pin & pin3 connected, then power on the system. JCC Normal status: Clear CMOS: (TURN OFF AC POWER).. BIOS-Protect Jumper(JAV) The BIOS of the CPU card is contained inside the Flash ROM. If the jumper JAV is set as closed, you will be unable to flash the BIOS to the mainboard. However in this status, the system BIOS is protected from being attacked by serious virus such as CIH virus. ENABLE JAV DISABLE..3 Watchdog Timer Action Jumper setting(jwd) We provide the fuction of Watchdog Timer, set JWD closed for enable, otherwise,set JWD open for disable. DISABLE JWD ENABLE

13 ..4 FSB Jumper Setting(JFS0,) Jumpers labeled JFS0 and JFS are located on the mainboard providing users with CPU on the correct clock. The host bus speed can be set as 400/533/800MHz or AUTO select. Refer to the chart below for the location of these jumpers, and the table for information on how to set them. JFS0 JFS CPU FSB 400MHZ 533MHZ 800MHZ AUTO JFS0-3 OPEN -3 - JFS -3-3 OPEN -..5 Front Panel SPEAKER IDLED+ BUZZ DATA+ 0 9 RESETSW+ SLEEPLED- POWERSW+ SLEEPSW+ BUZZ DATA- IDLED- IDE-LED RESETSW- RSTSW# SLEEPLED+ GRELED POWERSW- PWRSW SLEEPSW- SLEEPSW KEYLOCK- KEYLOCK KEYLOCK+ PWRLED- PWRLED PWRLED+ PWRLED+ 6 NC SLEEPSW- 6 SLEEPLED- BUZZDATA+ 7 KEYLOCK+ SLEEPSW+ 7 RESETSW- 3 PWRLED- 8 BUZZDATA- 3 POWERSW- 8 RESETSW+ 4 NC 9 KEYLOCK- 4 POWERSW+ 9 IDELED- 5 NC 0 NC 5 SLEEPLED+ 0 IDELED+

14 -3 PWRLED The power LED indicates the status of the main power switch. -8 BUZZD ATA The connector connects to the case s buzzer. 7-9 KEYLOCK The connector can be connected to the keyboard lock sowith on the case for locking the keyboard. - SLEEPSW Push once the swith connected to this header,the system enters suspend mode. 3-4 POWERSW The connector connects to the case s power botton. 5-6 SLEEPLED When the system enter green mode, the LED will flash. 7-8 RESETSW The connector connects to the case s reset switch. Press the swith once, the system resets. 9-0 IDELED The connector connects to the case s IDE indicator LED indicating the activity status of IDE hard disk. 3

15 Structure Shown As Below Chapter 3 FrontPane +V PowerSupply Intel ( ICH5) 880EB ATX Power CPU FAN 84pin DDR 64MB ATI RADEON 7000 Intel 848P (MCH) BIOS FDD USB.0X4 NORCO-4607 IDE LPT Connec- COM(,) EXTPOWER Serial ATA VGA NORCO-4607 MKB LAN AC 97 4

16 Intel 880EB ( ICH5) CPU FAN 84pin DDR Intel 865PE (MCH) FDD LPT I DE EXT POWER VGA NORCO-4607 LAN Front Panel +V Power Supply ATX Power NORCO-4607 AC 97 ATI RADEON 7000 COM(,) Serial ATA MKB 3MB/64MB USB.0X4 BIOS 5

17 Chapter 4 Watchdog Timer Action We provide the function of Watchdog Timer. Users could select different Watchdog Timer function to set I/O EFH. Another control port is EFH.The introduction of Watchdog Timer action jumper setting is following:. Set with I/O EFH I/O address EC value ~EFH: Set Timer count from to 39 (second/minute) F0H: Set Timer as minute FH: Set Timer as second (Default setting) FH: Stop/clear Watchdog Timer 0: Disable Watchdog Timer eg:set Watchdog Timer (5 minute) MOV DX,0EFH MOV AL,0F0H OUT DX,AL MOV AL,5 OUT DX,AL eg:stop Watchdog Timer MOV DX,0EFH MOV AL,0FH OUT DX,AL. set with EFH We could manipulate another port to achieve the operation which aim for W8367 super I/O chip from Winbond computer. The operation port of INDEXP DATAP are FH and FH. Under the DEBUG, we could operate port with writing conesponding data. port definition: EH: INDEXP FH: DATAP F5H: command memory,store minue/second definition F6H: command memory,store Timer count ~EFH: Set Timer count from to 39 (second/minute) 08H: Set Timer as minute 00H: Set Timer as second 6

18 eg:setup Watchdog Timer of 30 second Under the DOS run DEBUG,then put in: O E 87 O E 87 ;analysis code O E 07 O F 08 ;Select LOGIC Device O E F5 O F 00 ;select time unit as second O E F6 0 F 30 ;setup Timer Count as 30 second 7