Next thing you want to check for is if the truck has an aftermarket key fob or security system or satellite radio. If you are not sure, please check

Transcription

1

2 Next thing you want to check for is if the truck has an aftermarket key fob or security system or satellite radio. If you are not sure, please check the back of the OBD port for a PURPLE wire. Follow that purple wire all the way up to its main harness. If you see that there is another wire spliced INTO that purple wire, please cut that wire connecting to the purple wire just for the programming procedure. Do NOT cut the purple wire. After the programming is complete you can reconnect the wire to the purple wire by soldering it and taping it back up. If you see that there is NOTHING spliced into the purple wire, then you should be good to go as long as you have the proper fuses removed.

3

4

5

6 $0101 No data received. If the flash had begun and went half way and then gave you this error on a duramax PLEASE return to step 1 of LB7/LLY flashing steps. If y USB cable is faulty or not connected. In rare circumstances the PC operating system or the EFILive software may be malfunctioning. In even rarer circumstances the FlashScan or AutoCal device s USB circuitry may have been damaged. That damage occurs when the laptop is powered by a voltage inverter supplied from the vehicle s battery. A power inverter must never be used to power the laptop while it is connected via FlashScan or AutoCal to the vehicle. Check USB cables, plugs and connections. Try using a different USB port and/or different USB cable. Try rebooting the PC/laptop. Try using a self-powered USB hub between the PC/laptop and FlashScan or AutoCal. Try re-installing EFILive software which also re-installs the USB drivers. MAKE SURE EVERYTHING IS UP TO DATE $0533 No VIN license slots available. An attempt was made to license a controller when no free VIN licenses slots were available. Additional VIN license slots can be purchased for FlashScan devices from our on-line web store. FlashScan and AutoCal devices may support up to 221 VIN license slots. Some AutoCal devices may be configured by the supplier with a smaller maximum VIN license limit. $0532 Controller not licensed. An attempt was made to program a controller before it was licensed. License the controller before attempting to program it. You can license a controller using the on-screen prompts via FlashScan or AutoCal. $0531 the controller serial number stored in the tune file does not match the controller's serial number. If you get this error you are going to have to double check the information you have provided us with on your initial order. If there is ONE digit off, the tune file won t work. If this is the case you will have to get a new file made by us. But before flashing it in, we will need to return the truck back to full stock before putting the new tune in. $0537 Controller is locked with a custom key. An attempt was made to read or program a controller that cannot be unlocked using the standard GM keys. If you know the key that was used to lock the controller, please use the unlock option in the EFILive software to unlock the controller before attempting to read or reflash the controller again. If you don t know the unlock keys, you will have to find out the last person who flashed/updated the ecm in question because they will be the holder of the unlock code. If this is unknown and no way of finding out, unfortunately you will need to replace the ecm to get another program installed. $0549 Ignition is switched off. Ignition switch must be in the on position. Switch on the ignition and retry the operation.

7 $0535 AutoCal is not yet linked to a FlashScan. See also error $010D An attempt was made to program a controller using an AutoCal device that has not yet been linked to its parent FlashScan device. All AutoCal devices must be linked to a parent FlashScan device before they can be used to re-flash any controller. Please connect both FlashScan and AutoCal devices and then use the EFILive Control Panel (aka EFILive $0532 Controller not licensed. An attempt was made to program a controller before it was licensed. License the controller before attempting to program it. You can license a controller using the on-screen prompts via FlashScan or AutoCal. PICTURE DESCRIPTION FOR SENSOR REMOVAL ON LML DURAMAX s (11-16)

8