Gospeed.Racer Hub Assembly for the Asus EEEpc
|
|
- Janis Lucas
- 5 years ago
- Views:
Transcription
1 Gospeed.Racer Hub Assembly for the Asus EEEpc Before you begin: Please understand that these harnesses are all tested one at a time before I ship them. By installing this harness, you agree to assume any liability for damages incurred. Please take your time, and make sure there is NOTHING making contact with the motherboard that could cause a short. Please feel free to contact me at gospeed.racer@verizon.net if you should ever have any problems, concerns, or feedback Now, lets get started! 1) First, please make sure your EEE is safely powered down and remove your battery. Remove your memory cover if equipped. Prepare a static free workplace. 2) Disassemble your EEE down to the motherboard. If you have never done this before, there is a great tutorial by ta2cba from the eeeuser.com forum here: 3) With your motherboard in hand, find the camera connector in the upper, left hand corner of the board. Plug the male plug into this connector. Now, double check to verify you are in the correct port; the audio and fan use the same connector. 4) Wrap the wire through the cutout provided for the fan wire. You may want to use a bit of Kapton tape or hot glue to hold the wire. Avoid the areas with holes in the motherboard, as screws and posts will go there.
2 5) Lay down a layer of Kapton tape or adhesive sheet to the board where the device will go. You will want to make sure it is large enough to cover the area where your devices will fit. You may want to trial fit them in the space provided. Peel off the double sided tape from the hub, and fix it as shown to the side of the reset button and away from the hole in the board. Also peel and stick the USB ports. Again, it is best to mock it up with the case to see where things will end up.
3 6) Run the green ground wire over along the bottom of the memory connector and up to the area where the wifi card sits. Remove one screw from the card, and attach the ground terminal. Tighten firmly but do not over tighten!
4 7) Route the red power wire along the top of the board, away from any holes in the board that will contain screws later. Run it above the wifi card connector and locate the voltage regulator shown in the following picture. The tab on the far right in the picture, colored in red and marked with a + is where you will be soldering the positive wire. 8) You will want to use a tiny amount of flux if you have it available, as well as adding a dab of solder. Adding solder will help melt the solder that is on the regulator. Strip the wire about 1/16 and make sure to tin the wire with a bit of solder. Hold the wire in place on top of the terminal and touch the iron to the top. If you have a proper iron, it should melt fairly fast, as soon as it melts (you will feel it drop a bit). Do not saturate the area with heat, if you cant get it to melt in about 5 seconds STOP and find a proper iron. I use a station, set about watts.
5 9) Now, route the Bluetooth module (if equipped) over to the opposite side of the motherboard through the cutouts provided in the board. Peel and stick it here as shown 10) Go back over your wiring and make sure everything is secure enough to be positioned in the case without moving. You may need to use some Kapton tape to secure the wires. If you don t have the Kapton tape, use hot glue. PLEASE make sure there are NO components touching the board directly! This can cause many different problems. If there is ANY contact, adjust or modify the parts so they are clear of any components. This is THE most critical step of the entire install! 11) Reassemble your EEE, checking to make sure everything fits securely and is not pinching any wires. Re-route the webcam connector to the new connector in the hinge area. 12) Reinstall your memory cover (if equipped) 13) You are now finished! When your operating system finishes loading, your device will be ready for use. If you have the internal Bluetooth, you will need to install the drivers.
6 14) If the machine does not detect the devices or the hub; Restart your EEE and press F2 to enter Bios when you first see video. 15) Navigate to Advanced, Onboard Devices Configuration, and look for Onboard Camera. If it is not on the list, the USB device is not connected, or there is a problem with the connections. Change the setting to Enabled if it is disabled. 16) Press F10 and Enter to reboot. Thank you for your purchase! If you have any questions or feedback, please me at: gospeed.racer@verizon.net
Parts List: Part # Tools List: Instructions:
Parts List: Part # 1 pair of Dayton Audio B652s 300-652 1 Dayton Audio DTA-2 amplifier 300-385 1 MP3 module 320-350 1 7805 +5 VDC voltage regulator 7805 1 12 VDC 2A power supply 129-077 1 2.1 mm panel
More informationAsus ZenFone 2 Motherboard Replacement
Asus ZenFone 2 Motherboard Replacement If you have problems with your phone rebooting at random times, you could have a faulty motherboard in your phone. Written By: Eduardo Nodarse ifixit CC BY-NC-SA
More informationBuffaloLabs WiFi Lantern Assembly guide version 1
BuffaloLabs WiFi Lantern Assembly guide version 1 Needed equipment: Solder iron Solder wire Cutter Wire stripper (optional) Hot glue gun Overview of the components (not including USB cable and box panels)
More informationWritten By: Patrick. Disassembly to clean dust from the fan and heat sink. HP Pavilion G6 disassembly for cleaning
HP Pavilion G6 disassembly for cleaning Disassembly to clean dust from the fan and heat sink. Written By: Patrick ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION Disassembly to clean dust from
More informationQuicksilver 606 TR-606 CPU Upgrade
Quicksilver 606 TR-606 CPU Upgrade D650C 128 Installation Guide Social Entropy Electronic Music Instruments TABLE OF CONTENTS WARNINGS... 1 OVERVIEW... 2 WHAT'S IN THE BOX... 3 OPENING THE TR-606 CASE...
More informationInspiron Service Manual. 2-in-1. Computer Model: Inspiron Regulatory Model: P69G Regulatory Type: P69G001
Inspiron 13 5000 2-in-1 Service Manual Computer Model: Inspiron 13-5378 Regulatory Model: P69G Regulatory Type: P69G001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps
More informationWritten By: Adam Redmond
HTC One S USB Port Replacement This guide will show you how to remove and replace the USB port on your HTC One S. Written By: Adam Redmond ifixit CC BY-NC-SA www.ifixit.com Page 1 of 17 INTRODUCTION This
More informationHow to hardwire the Sony DSC-W35 Digital Camera
How to hardwire the Sony DSC-W35 Digital Camera Copyright, PixController http://www.pixcontroller.com, all rights reserved. Rev. A 3/20/07 This document covers in detail how to modify the Sony DSC-W35
More informationWritten By: Danielson0014
Dell Inspiron LCD Screen Replacement Give step by step instructions on how to remove and replace the screen of your dell. Written By: Danielson0014 ifixit CC BY-NC-SA www.ifixit.com Page 1 of 9 INTRODUCTION
More informationMacBook Pro 15" Core Duo Model A1150 LCD Panel High Definition (1920x1200) Replacement
MacBook Pro 15" Core Duo Model A1150 LCD Panel High Definition (1920x1200) Replacement Written By: Ben Eisenman ifixit CC BY-NC-SA www.ifixit.com Page 1 of 25 INTRODUCTION By following this guide, you
More informationHTC One M9 Headphone Jack/Micro USB Board Replacement
HTC One M9 Headphone Jack/Micro USB Board Replacement Replace the headphone jack/micro USB board. Written By: Michael Chan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION Use this guide to
More information**** Never plug in your LED driver to AC power until all wiring is complete ****
1 RapidLED Plug-n-Play Solderless Retrofit Kit Contents Overview... 1 Warnings Read Me First!... 1 Dimmable Driver Controller and Driver Output Current Adjustment... 2 Kit Assembly... 2 Attaching Your
More informationipod Touch 4th Generation 30 Pin Dock Connector Replacement
ipod Touch 4th Generation 30 Pin Dock Connector Replacement Learn how to replace the 30 pin dock connector on an ipod touch 4th generation. Written By: Gabe Keehn ifixit CC BY-NC-SA www.ifixit.com Page
More informationHow To Install: C4000 EMV Upgrade Kit
How To Install: C4000 EMV Upgrade Kit IMPORTANT: Before proceeding with installation please verify you have the current card reader bezel in the kit. Correct bezel will have a small eject pin hole below
More informationSupplemental guide on Camera Fabrication
Supplemental guide on Camera Fabrication This document describes the steps for fabricating your camera and lighting system. 1 Materials needed Gather all your materials. You will need the small lexan sheet
More informationHP G disassembly for cleaning and
HP G62-453 disassembly for cleaning and thermal paste This is maintenance of an HP G62 series laptop. Written By: Bo Herrmannsen ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION Hi everyone,
More informationThank you for purchasing the Ultimate Sega Saturn Mod Chip! Installation Guide. For Use on all Model 1 Consoles Only
Thank you for purchasing the Ultimate Sega Saturn Mod Chip! Installation Guide For Use on all Model 1 Consoles Only *NOTE* When attempting to play a backup after installation is done, make sure to have
More informationRemoving and Replacing Parts
Removing and Replacing Parts Preparing to Work Inside the Computer Recommended Tools Screw Identification System Components Hard Drive Fixed Optical Drive Media Bay Devices Memory Modules Mini PCI Card
More informationCINTENNA ANTENNA REPAIR GUIDE
The Cintenna is a great tool when looking to transmit WIRELESS DMX data over obstacles or hard to reach places. Wireless DMX can have its issues when not having a good line of sight between the transmitter
More informationimac Intel 27" Retina 5K Display SATA Cable
imac Intel 27" Retina 5K Display SATA Cable Replacement Written By: Dozuki System 2017 guides.crucial.com Page 1 of 32 INTRODUCTION Use this guide to replace the SATA cable on the back of the logic board
More informationWritten By: Walter Galan
iphone 5s Display Assembly Replacement Replace the cracked or broken screen on your iphone 5s. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Use this guide to replace
More informationAlcatel One Touch Pop 7 Display Assembly Replacement
Alcatel One Touch Pop 7 Display Assembly Replacement This guide will show you how to replace the display panel and the digitizer. Written By: Riley Cooper ifixit CC BY-NC-SA www.ifixit.com Page 1 of 9
More informationDisassembly Procedure
Chapter 2 Disassembly Procedure Please follow the information provided in this section to perform the complete disassembly procedure of the Eee PC 1201HA. Be sure to use proper tools described before.
More informationWritten By: Walter Galan
iphone 6 Plus Front Panel Replacement Replace the Front Panel in your iphone 6 Plus. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 27 INTRODUCTION Use this guide to strip and replace
More informationWritten By: Gabriel Malestein
Motorola Moto G5 Plus Battery Replacement Replace a battery that is no longer holding a full charge. Written By: Gabriel Malestein ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION As batteries
More informationSamsung Galaxy S7 Edge Display Assembly
Samsung Galaxy S7 Edge Display Assembly Replacement Removing and replacing the display assembly on the Samsung Galaxy S7 Edge. Written By: Arthur Shi ifixit CC BY-NC-SA www.ifixit.com Page 1 of 25 INTRODUCTION
More informationOpenSprinkler v2.2u Build Instructions
OpenSprinkler v2.2u Build Instructions (Note: all images below are 'clickable', in order for you to see the full-resolution details. ) Part 0: Parts Check Part 1: Soldering Part 2: Testing Part 3: Enclosure
More informationThank you for purchasing the Ultimate Sega Saturn Mod Chip! Installation Guide. For Use on all Model 2 Consoles with SANYO Drives ONLY
Thank you for purchasing the Ultimate Sega Saturn Mod Chip! Installation Guide For Use on all Model 2 Consoles with SANYO Drives ONLY *NOTE* When attempting to play a backup after installation is done,
More informationWritten By: Anthony Valdez
ASUS Eee PC 1018P Fan Replacement This guide will show how to remove the fan, in order to replace it. Written By: Anthony Valdez ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION The CPU Fan
More informationWritten By: Sam Lionheart
iphone SE Display Assembly Replacement Replace the cracked or broken screen on your iphone SE. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Use this guide to replace
More informationSingle cable kit for the FCB1010
Single cable kit for the FCB1010 1. What is it? With this kit, you can turn your FCB1010 into a phantom powered floorboard, which can do 2-way MIDI communication over one single cable. After installing
More informationXPS 15 2-in-1. Service Manual. Computer Model: XPS Regulatory Model: P73F Regulatory Type: P73F001
XPS 15 2-in-1 Service Manual Computer Model: XPS 15-9575 Regulatory Model: P73F Regulatory Type: P73F001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better
More informationColecovision 5v Memory Mod Installation
Colecovision 5v Memory Mod Installation The Colecovision suffers from common failure points: the power supply, power switch, and 4116 DRAM. The power supply suffers from poor soldering, the power switch
More informationDell XPS 14z Owner s Manual
Dell XPS 14z Owner s Manual Computer model: L412z Regulatory model: P24G series Regulatory type: P24G001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better
More informationASUS A2000 Series Notebook consists of various modules. This chapter
Chapter 2 Disassembly Procedure Please follow the information provided in this section to perform the complete disassembly procedure of the notebook. Be sure to use proper tools described before. ASUS
More informationInstallation Manual. ID station. CamFi controller
ID station CamFi controller Last change : July 12th, 2016 1 Introduction This manual will guide you through the process of connecting a CamFi controller to your camera and pairing it to an ID station.
More informationWii Nunchuk Transceiver. Wiring Diagrams
Wii Nunchuk Transceiver Wiring Diagrams Wii Nunchuk Controller Wiring SCL SCL SDA +3v3 +3v3 Det SDA To Nunchuk Controller Top View Bottom View Bottom View 2.4GHz Wireless Transceiver CMD RXD TXD VCC 220Ω
More informationREMOVE COVERS. 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer.
REMOVE COVERS 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer. 3. Fully open the Top Cover. 4. Release the tab on the right
More informationRevised: Page 1
Brought To You By And Designed By: Revised: 2017-05-07 Page 1 Features Of The Universal PSU Kit: Fits all standard Apple II and /// Power Supply Enclosures. (all parts included, user supplies household
More informationAdventure Time Coffee Cup Lamp with MakeCode
Adventure Time Coffee Cup Lamp with MakeCode Created by Ruiz Brothers Last updated on 2019-01-08 03:18:49 AM UTC Guide Contents Guide Contents Overview Prerequisite Guides Circuit Playground Express 3
More informationEQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors.
EQ573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationSamsung Galaxy S10 Motherboard
Samsung Galaxy S10 Motherboard Replacement This guide shows how to remove the motherboard for the Galaxy S10. This assembly includes the USB-C charging port. Written By: Arthur Shi ifixit CC BY-NC-SA www.ifixit.com
More informationIPhone 7 Plus Chargeport REPAIR GUIDE. Version Edition
IPhone 7 Plus Chargeport REPAIR GUIDE Version 1 2016 Edition IPhone 7 plus Chargeport Repair Guide RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE TO COMPLETE, INITIAL,
More informationJippo Play - Installation Manual Page 1 INSTALLATION MANUAL. Intro Camera Operation Installation - Wrangler JK... 2
Jippo Play - Installation Manual Page 1 INSTALLATION MANUAL CONTENTS Intro... 1 Camera Operation... 2 Installation - Wrangler JK... 2 Jippo Play Configuration... 6 VES Installation... 7 Camera Installation...
More informationMotorola Moto Z Play Motherboard Replacement
Motorola Moto Z Play Motherboard Replacement How to replace a broken Motorola Moto Z Play motherboard. Written By: Kaitlyn Fisher ifixit CC BY-NC-SA www.ifixit.com Page 1 of 14 INTRODUCTION Follow this
More informationimac Intel 27" EMC 2639 Hard Drive
imac Intel 27" EMC 2639 Hard Drive Replacement Replace the Hard Drive in your imac Intel 27" EMC 2639. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Replacing the
More informationNintendo 3DS D-pad Replacement
Nintendo 3DS D-pad Replacement Nintendo 3DS D-pad replacement. Written By: David Hodson ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION Replace the D-pad on your 3DS to get full movement capabilities
More informationimac Intel 27" Retina 5K Display CPU Replacement
imac Intel 27" Retina 5K Display CPU Replacement Replace or upgrade the CPU in your imac Intel 27" Retina 5K Display. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 36 INTRODUCTION
More informationCanon PowerShot S500 Flash Assembly Replacement
Canon PowerShot S500 Flash Assembly Replacement Replace the Flash Assembly in your Canon PowerShot S500. Written By: Nathan Balcom ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION This guide
More informationAssembly of the TACOS WAT-910BD Housing v2
1) Circuit Diagram 2) Assembly of PCB a)tools Required. Only simple hand tools are necessary to complete the assembly of the PCB. - Soldering Iron and solder - Needle nose pliers - Wire clippers/trimmers
More informationWritten By: Sam Lionheart
iphone 5s Earpiece Speaker Replacement Replace the earpiece speaker in an iphone 5s. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION Use this guide to replace a broken
More informationWritten By: Sam Lionheart
iphone SE SIM Eject Lever Replacement Replace the SIM eject lever in an iphone SE. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION Is your SIM card getting stuck in
More informationToshiba Satellite A105-S4011 Touchpad
Toshiba Satellite A105-S4011 Touchpad Replacement This guide will instruct you on how to remove the current touchpad from this laptop and how to reinstall another. This is a straightforward process and
More informationLED Lighting Kit For Elara NanoEdge Fixed Frame. Installation Guide. Attention: Read this guide before assembling your screen.
LED Lighting Kit For Elara NanoEdge Fixed Frame Installation Guide Attention: Read this guide before assembling your screen. INTRODUCTION GETTING STARTED WARNING - Sharp Edges This product may contain
More informationIntel NUC Kit NUC8i7HNK & NUC8i7HVK User Guide. Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide
Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers
More informationThe basic product comes with the IRS5 control board, 3 internal cables, 1 external cable with a 5 volt adapter and a mounting bracket with hardware.
Please read these instructions and watch the Installation Video before you proceed with the installation of the PC-IRS5-01. Installation Video: http://youtu.be/os98e32vhb4 The PC-IRS5-01 Infrared Receiver
More informationTIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE
TIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE Table of Contents 0. Components List + Tools 0. PCB Sides 03. PCB Assembly 04_. Diode N448 04_. Laying Resistors 04_3. Capacitors 04_4. Quartz 04_5. 78L05
More informationMotorola Moto G4 Plus Motherboard Replacement
Motorola Moto G4 Plus Motherboard Replacement Remove and replace your motherboard as a prerequisite to other guides. Written By: Andre Rives ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION
More informationASUS Zen Pad 10 Micro USB Port & Camera Replacement
ASUS Zen Pad 10 Micro USB Port & Camera Replacement Remove the motherboard and replace the camera and micro USB port. Written By: Mr Circuit ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION
More informationIQ32 Upgrade Kit Assembly Instructions
IQ32 Upgrade Kit Assembly Instructions Jim Veatch WA2EUJ September 17, 2018 TABLE OF CONTENTS 1. INTRODUCTION... 3 2. IQ-32 UPGRADE KIT INVENTORY... 4 3. PREPARING THE RS-HFIQ AND SIDE PANELS... 6 4. CONNECTING
More informationPackard Bell. EasyNote BU Series. Disassembly Guide
Packard Bell EasyNote BU Series Disassembly Guide Table of Contents Overview...3 Technician Notes...3 Disassembly Instructions...3 Reassembly Instructions...3 Required Tools...3 Battery...4 Memory...4
More informationWritten By: Sam Lionheart
iphone 5c Front Panel Replacement Replace the Front Panel on your iphone 5c. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 24 INTRODUCTION For an easier repair, use our fix kit
More informationiphone 6s Front Panel Replacement
iphone 6s Front Panel Replacement Note: DIY at your own risk. New beginner must be careful, screens got problems mostly due to wrong installation process. INTRODUCTION Use this guide to replace a cracked
More informationMac mini Model A1283 Terabyte Drive
Mac mini Model A1283 Terabyte Drive Replacement Install a terabyte worth of storage space in your Mac mini Model A1283. Written By: Miroslav Djuric ifixit CC BY-NC-SA www.ifixit.com Page 1 of 21 INTRODUCTION
More informationPowerBook G4 Aluminum 12" GHz Heat Sink Replacement
PowerBook G4 Aluminum 12" 1-1.5 GHz Heat Sink Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION The heat sink helps keep the processor cool and happy. TOOLS: Arctic
More informationimac Intel 27" EMC 2546 SSD Replacement
imac Intel 27" EMC 2546 SSD Replacement Remove your imac's SSD, or the SSD portion of your imac's Fusion Drive. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 33 INTRODUCTION If your imac
More informationApex Tablet 7 Battery Replacement
Apex Tablet 7 Battery Replacement This guide will instruct you on how to replace the lithium-ion battery inside the Apex 7" Tablet. Written By: Corrine Nief ifixit CC BY-NC-SA www.ifixit.com Page 1 of
More informationInsert the male, 90 angled, 2x10 connectors into the corresponding 2x10 sockets and put them in place, flat under the PCB. Solder.
MC624 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationWritten By: Sam Lionheart
iphone 6 Front Panel Replacement Replace the bare front panel of an iphone 6. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 27 INTRODUCTION For an easier repair, use our fix kit
More informationMacBook Air 13" Mid 2013 Heat Sink
MacBook Air 13" Mid 2013 Heat Sink Replacement Replace the Heat Sink in your MacBook Air 13" Mid 2013. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION Use this guide
More informationMotorola Droid RAZR M USB Charging Port Replacement
Motorola Droid RAZR M USB Charging Port Replacement Replacement of the USB charging port on the Motorola Droid RAZR M Written By: Nick Boring ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION
More informationDual Mount Universal Kit Aftermarket CMOS Camera with Optional Parking Gridlines Installation Instructions (Kit # )
Please read thoroughly before starting installation and check that kit contents are complete. Items Included in Kit: Chassis Harness Power Harness with RCA connectors Camera mounted on license plate bracket
More informationCAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly
CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the
More informationInstallation Instructions
Second Kit for the GrandSTAR Jukebox Kit #26694913 Purpose: These instructions outline the procedures to install a second 1000W into the GrandSTAR jukebox with the AV controller (shown) or the 4 Channel
More informationCR2032 with Tab Installation Guide Page 1 of 11. CR2032 with Tabs Installation Guide
CR2032 with Tab Installation Guide Page 1 of 11 CR2032 with Tabs Installation Guide Thank you for your purchase of a CR2032 coin cells battery with tabs from Mortoff Games. We know that you have a choice
More informationNabi Big Tab HD24 Speakers Replacement
Replacing the speakers in your tablet to get the sound back. Written By: Kevin Garcia ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION The Nabi Big Tab HD 24 has two internal speakers. When
More informationAsus Transformer T100 Motherboard
Asus Transformer T100 Motherboard Replacement Replace the motherboard of your Asus Transformer T100. Written By: Taylor Pantiga ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION The motherboard
More informationSamsung Galaxy S6 Daughterboard
Samsung Galaxy S6 Daughterboard Replacement Replace the daughterboard on a Samsung Galaxy S6. Written By: Dante Mazzanti ifixit CC BY-NC-SA www.ifixit.com Page 1 of 28 INTRODUCTION Use this guide to replace
More informationToshiba Satellite P105-S6024 LCD Display Replacement
Toshiba Satellite P105-S6024 LCD Display Replacement Replacement of the LCD Display in the Toshiba Satellite P105-S6024 Geschrieben von: Jacob Micallef ifixit CC BY-NC-SA de.ifixit.com Seite 1 von 6 EINFÜHRUNG
More informationVersion 1.1. A guide for BLU2 installations.
BLU2 Installation Guide Optional Image Version 1.1 A guide for BLU2 installations. Table of Contents TABLE OF FIGURES... 3 BEFORE YOU BEGIN... 5 PeopleNet System Installation Manual... 6 BLU2... 6 BLU2
More informationOpenSprinkler v2.1u Build Instructions
OpenSprinkler v2.1u Build Instructions (Note: all images below are 'clickable', in order for you to see the full-resolution details. ) Part 0: Parts Check Part 1: Soldering Part 2: Testing Part 3: Enclosure
More informationIntel NUC Kit D54250WYKH & D34010WYKH User Guide. Intel NUC Kit D54250WYKH Intel NUC Kit D34010WYKH User Guide
Intel NUC Kit D54250WYKH Intel NUC Kit D34010WYKH User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers
More informationAcer Iconia Tab A3-A10 Touchscreen
Acer Iconia Tab A3-A10 Touchscreen Replacement You broke the digitizer but the display is still intact? Just simply replace the broken touchscreen!! Written By: Cecil His Mahier ifixit CC BY-NC-SA www.ifixit.com
More informationHow to - implant the "GC BT Scope1" into a LX90 Seite 1 / 8 LX90_with_Bluetooth_inside.doc
How to - implant the "GC BT Scope1" into a LX90 Seite 1 / 8 Created Last update November 2 nd 2009 by Hendrik Wölper February 13 th, 2010 by Hendrik Wölper 1 Table of Content 1 Table of Content...1 2 Introduction...1
More informationUF-3701 Power Board Construction Guide
Page 1/5 Soldering and Part Placement See the Chapter 3 of the MIT 6270 Manual for information on electronic assembly, including soldering techniques and component mounting. Construction Information All
More informationEmatic Genesis Screen Replacement
Screen replacement for the Ematic Genesis tablet Written By: Justin Rohrman ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION If the screen is cracked or damaged it may need to be replaced. This
More informationRetina MacBook 2015 Display Assembly
Retina MacBook 2015 Display Assembly Replacement Replace the display assembly on the Retina MacBook 2015. Written By: Geoff Wacker ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION Use this guide
More informationDell Latitude C800 Service Manual
Dell Latitude C800 Service Manual Dell Latitude C800 Service Manual Before You Begin Preparing to Work Inside the Computer Recommended Tools Screw Identification Removing and Replacing Parts System Components
More information7" Touch Screen Display
7" Touch Screen Display Installation Guide Contents Minimum Requirements...1 Select a Location...1 Initial Setup...2 Unboxing...2 Installation...3 Prepare the Panel...3 Install the Mounting Plate...3 Mount
More informationWritten By: Sam Lionheart
iphone 5s Lightning Connector Replacement Remove the Lightning connector/headphone jack assembly from your iphone 5s. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION
More informationConstructing a Low-Cost Mobile Eye Tracker
==== Constructing a Low-Cost Mobile Eye Tracker ==== Section 1: Introduction This is a detailed set of instructions on how to build a low-cost mobile eye-tracking system from off-the-shelf components.
More informationDell XPS L702X Service Manual
Dell XPS L702X Service Manual Regulatory model: P09E series Regulatory type: P09E002 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer.
More informationRetina MacBook 2015 Lower Case Assembly Removal
Retina MacBook 2015 Lower Case Assembly Removal Separate the lower case assembly. Written By: Geoff Wacker ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION Prerequisite-only guide for separating
More informationComputer Assembly (Installing Mother Board & CPU)
Computer Assembly (Installing Mother Board & CPU) IT@SCHOOL HARDWARE TEAM Biju Thiruvananthapuram Sree Kumar Kottarakkara Shamsudeen Attingal Pradeep Mattara Wandoor Pre-Installation Precaution Mother
More informationSony Vaio VPCCW21FX System Board Removal
Sony Vaio VPCCWFX System Board Removal General motherhood : Standard rules apply regarding static electricity discharge Keep track of screws that are removed by labeling each group and writing on the internal
More informationFlying Tickets FT Operation & Service Manual. Version 1.0. * Read this manual before use
Flying Tickets FT-65-1001 Operation & Service Manual Version 1.0 * Read this manual before use Flying Ticket Manual V1.0 General Remark If you encounter any difficulties or if you need support on how to
More informationDell Inspiron N5110 Service Manual
Dell Inspiron N5110 Service Manual Regulatory model: P17F Regulatory type: P17F001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer.
More informationiphone 6 Plus 5GHz Wi-Fi Antenna Replacement
iphone 6 Plus 5GHz Wi-Fi Antenna Replacement Replace the 5GHz Wi-Fi antenna in your iphone 6 Plus. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION Use this guide to
More informationWritten By: Sam Lionheart
iphone SE Logic Board Replacement Use this guide to replace a faulty logic board in your iphone SE. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 27 INTRODUCTION Use this guide
More informationThe Radio Control Temperature Logger (RCTL) Manual For hardware version 1.0 Manual version 1.0b
The Radio Control Temperature Logger (RCTL) Manual For hardware version 1.0 Manual version 1.0b All materials owned by Dan Gebhardt Introduction This device records the temperature of a model engine during
More information