L1-34A February ADP-40 Analog Door Phone Hardware Installation Guide

Transcription

1 L1-34A February 2006 ADP-40 Analog Door Phone Hardware Installation Guide

2 Trademarks ADP-40 Analog Door Phone Hardware Installation Guide Trademarks Any brand names and product names included in this manual are trademarks, registered trademarks, or trade names of their respective holders. To the Holder of the Manual The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change the contents without prior notice. In no event will ADTRAN be liable for any special, incidental, or consequential damages or for commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication. Software Licensing Agreement Each ADTRAN product contains a single license for ADTRAN supplied software. Pursuant to the Licensing Agreement, you may: (a) use the software on the purchased ADTRAN device only and (b) keep a copy of the software for backup purposes. This Agreement covers all software installed on the system as well as any software available on the ADTRAN website. In addition, certain ADTRAN systems may contain additional conditions for obtaining software upgrades. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. 901 Explorer Boulevard P.O. Box Huntsville, AL Phone: (256) Copyright 2006 ADTRAN, Inc. All Rights Reserved. Printed in U.S.A. 2 Copyright 2006 ADTRAN, Inc L1-34A

3 ADP-40 Analog Door Phone Hardware Installation Guide Conventions Conventions Notes provide additional useful information. Cautions signify information that could prevent service interruption or damage to equipment. Warnings provide information that could prevent injury or endangerment to human life L1-34A Copyright 2006 ADTRAN, Inc. 3

4 Safety Instructions ADP-40 Analog Door Phone Hardware Installation Guide Safety Instructions When using your telephone equipment, please follow these basic safety precautions to reduce the risk of fire, electrical shock, or personal injury: 1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. 2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote risk of shock from lightning. 3. Do not use the telephone to report a gas leak in the vicinity of the leak. 4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for special disposal instructions. 5. The socket-outlet shall be installed near the equipment and shall be easily accessible. Save These Important Safety Instructions 4 Copyright 2006 ADTRAN, Inc L1-34A

5 ADP-40 Analog Door Phone Hardware Installation Guide FCC Radio Frequency Interference Statement FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Canadian Emissions Requirements This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-003 of the Department of Communications. Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques de Class A prescrites dans la norme sur le materiel brouilleur: Appareils Numériques, NMB-003 edictee par le ministre des Communications L1-34A Copyright 2006 ADTRAN, Inc. 5

6 Warranty and Customer Service ADP-40 Analog Door Phone Hardware Installation Guide Warranty and Customer Service ADTRAN will repair and return this product within the warranty period if it does not meet its published specifications or fails while in service. It is the responsibility of the entity (ADTRAN Certified Dealer or Service Provider) that sold you your ADTRAN equipment to diagnose and initiate the product return to ADTRAN. Product Registration Registering your product helps ensure complete customer satisfaction. Please take time to register your products on line at Click on Service/Support and then on Product Registration under Support Product Support Information Post-Sale Support The entity (ADTRAN Certified Dealer or Service Provider) that sold you your ADTRAN equipment should serve as the first point of contact for support. If additional support is needed, the ADTRAN Support website provides a variety of support services such as a searchable knowledge base, updated firmware releases, latest product documentation, and troubleshooting tools. All of this, and more, is available at: Installation and Maintenance Support The entity (ADTRAN Certified Dealer or Service Provider) that sold you your ADTRAN equipment should serve as the first point of contact for support. However, if you have purchased ADTRAN Custom Extended Services (ACES), you are eligible to access the ACES Help Desk. The ACES program offers multiple types and levels of installation and maintenance services which allow you to choose the kind of assistance you need. This support is available at: For questions, call the ACES Help Desk. Training ACES Help Desk (888) 874-ACES (2237) The Enterprise Networks (EN) Technical Training Department offers training on our most popular products. These courses include overviews on product features and functions while covering applications of ADTRAN's product lines. ADTRAN provides a variety of training options, including customized training and courses taught at our facilities or at your site. For more information about training, please contact your Territory Manager or the Enterprise Training Coordinator. Training Phone (800) , ext Training Fax (256) Training training@adtran.com 6 Copyright 2006 ADTRAN, Inc L1-34A

7 Table of Contents Overview Features Applications Specifications Installation Flush Mounting New Construction Flush Mounting Old Work Surface Mounting Wiring Grounding (optional) Assembling Operation L1-34A Copyright 2006 ADTRAN, Inc. 7

8 Table of Contents ADP-40 Analog Door Phone Hardware Installation Guide 8 Copyright 2006 ADTRAN, Inc L1-34A

9 List of Figures Figure 1. ADP-40 Analog Door Phone Figure 2. Wiring the ADP Figure 3. Assembling the ADP Figure 4. Volume Controls L1-34A Copyright 2006 ADTRAN, Inc. 9

10 List of Figures ADP-40 Analog Door Phone Hardware Installation Guide 10 Copyright 2006 ADTRAN, Inc L1-34A

11 1. OVERVIEW The ADP-40 Analog Door Phone is a compact, weather and vandal resistant, telephone line powered speaker phone designed to provide two-way handsfree communication. The ADP-40 s compact size allows it to be mounted in any standard, single-gang electrical box. It can be connected directly to any analog station port on the NetVanta 7100 when the port is configured as a hotline phone. Multiple ADP-40 s can be used with the NetVanta 7100, each connected to a separate analog station port. The ADP-40 can also be used on any analog Private Automatic Branch exchange/key Service Unit (PABX/KSU) station programmed for hotline or automatic ring-down (if the station supports forward disconnect). When the CALL button is pressed, the ADP-40 goes off-hook and remains off-hook until a forward disconnect is detected from the NetVanta 7100 or the three-minute call time out period has elapsed. The unit then automatically disconnects. The ADP-40 may also be disconnected by pressing the CALL button again. The ADP-40 features microphone and speaker volume controls and automatically answers incoming calls for remote monitoring or answering a speaker phone call. The ADP-40 (shown in Figure 1) is ready to use out of the box when connected to a provisioned analog station port on the NetVanta Figure 1. ADP-40 Analog Door Phone Features Compact Size: Faceplate is the size of a typical mid-sized single-gang wall plate Mounting: Flush mounts in any single-gang (1.75-inch deep minimum) electrical box (not included) or surface mounts in a single-gang wet location box (not included) Weather Resistant Features: Mylar speaker, faceplate gasket, microphone and speaker gasket, sealed push-button switch, self-draining microphone mount Vandal Resistant Features: 18-gauge stainless steel faceplate, stainless steel push button, stainless steel speaker screen, hex drive mounting screws Telephone line powered Two-way handsfree communication Adjustable microphone and speaker volumes Three-minute call time out Auto-answer feature for remote monitoring L1-34A Copyright 2006 ADTRAN, Inc. 11

12 Overview ADP-40 Analog Door Phone Hardware Installation Guide Applications Commercial, industrial, and residential door security Business delivery entrances Door or gate communication Use in conjunction with NetVanta 7100 analog station ports Compliments the NetVanta Door Unlock Relay to unlock a door located adjacent to the ADP-40 Use on any analog PABX/KSU station programmed for hotline or automatic ring-down with forward disconnect set to a 500 ms or greater battery removal Specifications Power: Telephone line powered (18 VDC, 30 ma minimum) Ring Voltage: 25 VAC RMS minimum (for auto answer) Speaker Volume: Approximately 62 db maximum at 1 meter Forward Disconnect Time Out: 500 ms, battery removal REN: 0.8 A Connectors: Two gel-filled butt connectors Compliance: FCC Part 15 Class B Faceplate Dimensions: 4.88-inch H x 3.13-inch W x 0.18-inch D (123.8-mm H x 79.4-mm W x 4.6-mm D) Shipping Weight: 1.0 lb (0.45 kg) Operating Temperature: -15 F to 130 F (-26 C to 54 C ) Relative Humidity: 5 to 95 percent humidity, noncondensing This product is only intended to be used with the NetVanta Series products. 12 Copyright 2006 ADTRAN, Inc L1-34A

13 . ADP-40 Analog Door Phone Hardware Installation Guide Installation 2. INSTALLATION The ADP-40 Analog Door Phone is designed to be flush mounted in any standard single-gang electrical box with a minimum depth of 1.75 inches (not included). The ADP-40 can also be surface mounted in any standard single-gang wet location (weather proof) electrical box with a minimal depth of 1.75 inches (not included). Flush Mounting New Construction 1. Fasten a standard, single-gang electrical box to a stud using standard flathead drywall screws. The front of the box should extend approximately 1/2 inch from the front surface of the wall stud on which it is mounted (this could vary depending on the wall sheathing and siding thickness). 2. When installing the siding, cut a hole just large enough for the electrical box opening. The electrical box must be mounted flush and must not extend beyond the front surface of the siding. Flush Mounting Old Work 1. Make sure the mounting location is free of wall studs, wires, etc. 2. Place the electrical box level against the siding. Trace the outline of the box on the siding. 3. Cut a hole through the siding and wall sheathing just large enough for the electrical box. 4. Fasten a standard, single-gang electrical box to the siding using standard flathead drywall screws. The front surface of the electrical box can be mounted flush against wood siding or can be recessed and mounted flush against sheathing when mounting on aluminum, steel, or vinyl siding. Cutting the hole in the siding too large can cause faceplate misalignment and compromise the gasket seal. When mounting to 4-inch or less horizontal lap siding, the unit can be flush mounted horizontally against the siding or a siding mounting block can be used. Contact your siding installer for the correct mounting block part number. Surface Mounting A standard single-gang wet location (weather proof) electrical box (Pass & Seymour 93C6 or equivalent) can be used to surface mount the ADP Drill a small wire exit hole in the wall. 2. Pull the wire through and seal the hole around the wire with putty or caulking. 3. Route the wire into the wet location electrical box. 4. Secure the box to the wall or a post and seal the hole in the box around the wire with putty or caulking. In surface mount applications, conduit can be used to route the wire to the electrical box L1-34A Copyright 2006 ADTRAN, Inc. 13

14 Installation ADP-40 Analog Door Phone Hardware Installation Guide Wiring 1. Connect the red (ring) and green (tip) wires attached to the rear of the circuit board to the center pair of your CAT 5 cable using the gel-filled butt connectors provided (see Figure 2). The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19- to 26-gauge wire with a maximum insulation of inches. Do not strip wires prior to terminating. 2. Crimp the gel-filled butt connectors with pliers. Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and the telephone line. It is recommended that a surge protector be installed to protect against such surges. Grounding (optional) To increase surge protection, ADTRAN recommends grounding the ADP Loosen the PCB mounting screw labeled (as shown in Figure 2). 2. Fasten a wire to the provided ring terminal and connect the ring terminal from the PCB mounting screw to earth ground (grounding rod, water pipe, etc.). 3. After connecting the ring terminal to the PCB mounting screw, bend the terminal up to avoid interference with the electrical box. Ring Connector (included) Earth Ground (optional) Rear View of the Circuit Board Mounting Plate Red (Ring) * Gel-Filled Butt Connectors (included) Not polarity sensitive Green (Tip) To Analog Station Figure 2. Wiring the ADP Copyright 2006 ADTRAN, Inc L1-34A

15 ADP-40 Analog Door Phone Hardware Installation Guide Installation Assembling 1. After an electrical box is securely mounted and wires are connected, remove the paper liner from the faceplate gasket. 2. Place the side of the gasket from which you removed the paper toward the back side of faceplate, aligning the gasket with the CALL button hole. 3. Push the 1-inch, 6-32 screws through the faceplate holes and the small holes in the gasket. 4. Position the circuit board mounting plate over the screws (see Figure 3). 5. Align the hexdrive screws with the electrical box screw holes and tighten the screws until the gasket is fully collapsed and the CALL button is protruding through the clearance hole in the faceplate. The included 1/4-inch thick gasket provides an adequate seal for most siding surfaces; however, for rough surfaces (i.e., brick, stucco, etc.) additional caulking may be required. Optional Mounting Ears Optional Wing Brackets 3.125" 1.75" Deep Minimum (2) Gel-Filled Butt Connectors (included) Red 4.875" Green Call Electrical Box (not included) (4) Optional Drywall Screws (not included) Circuit Board Mounting Plate (included) 1/4" Thick Foam Faceplate Gasket (included) (2) 1" Long, /64" Hexdrive Flathead Screws (included) Faceplate (included) Figure 3. Assembling the ADP L1-34A Copyright 2006 ADTRAN, Inc. 15

16 Operation ADP-40 Analog Door Phone Hardware Installation Guide 3. OPERATION Adjusting Speaker and Microphone Volumes Figure 4 shows the speaker and microphone volume controls set in the factory default positions. The speaker and microphone volume controls can be adjusted to increase or decrease the speaker or microphone volumes to the desired level. In noisy locations (background traffic, machinery, or wind), the microphone volume may need to be decreased if the distant party is inaudible over the speaker. If the microphone volume is set too high or too low, communication may suffer in one or both directions. 1. If volume adjustment is necessary, remove the faceplate and circuit board mounting plate. 2. Turn the circuit board mounting plate over to access the speaker and microphone volume controls. Adjust the volumes to the desired levels (see Figure 4). 3. Push the screws through the faceplate holes and the small holes in the gasket. 4. Position the circuit board mounting plate over the screws. 5. Align the hexdrive screws with the electrical box screw holes and tighten the screws until the gasket is fully collapsed and the CALL button is protruding through the clearance hole in the faceplate. Rear View of the Circuit Board Mounting Plate Speaker Volume Microphone Volume Note: Volume Controls are shown in factory default settings. Figure 4. Volume Controls Call Time Out The ADP-40 is equipped with a fixed call time out feature that automatically disconnects the unit after three minutes. Auto Answer The ADP-40 is factory set to automatically answer when an inbound call is detected. Call Button When the CALL button is pressed, the ADP-40 phone goes off-hook, much like a standard speaker phone. In the event that the line is busy or there is a ring-no-answer, the ADP-40 can be disconnected by pressing the CALL button. It automatically hangs up when a forward disconnect is received from the NetVanta 7100 or the three-minute call time out period elapses. 16 Copyright 2006 ADTRAN, Inc L1-34A

17 Index A ADP-40 applications 12 assembling 15 features 11 flush mounting 13 grounding 14 installation 13 operating 16 overview 11 specifications 12 surface mounting 13 wiring 14 applications 12 assembly 15 auto-answer 16 W warranty 6 wiring the ADP C call button 16 call time-out 16 customer service 6 F features 11 flush mounting 13 G grounding 14 I installation 13 M microphone volume 16 O operation 16 overview of ADP P product registration 6 S speaker volume 16 specifications 12 surface mounting 13 T trademarks 2 V volume controls L1-34A Copyright 2006 ADTRAN, Inc. 17

18 Index ADP-40 Analog Door Phone Hardware Installation Guide 18 Copyright 2006 ADTRAN, Inc L1-34A