Quick Start Installation Guide

Transcription

1 RM-iCLASS Series Quick Start Installation Guide Version C0 Document Part Number UM-208 June 2009 OVERVIEW The RM-iClass Quick Start Installation Guide provides a summary of installation and connection information for RM-iC series readers. The RM-iCLASS (RM-iC) series readers provide an enclosed RM-4 board and attached iclass read head, available in the following styles: RM iclass Read only reader - an enclosed RM-4 and attached iclass read head (Part Number RM1-iC) RM iclass Read only reader with keypad, - an enclosed RM-4 with keypad and attached iclass read head (Part number RM2-iC) RM iclass Read only reader with keypad and LCD - an enclosed RM-4 with keypad, LCD display, and attached iclass read head (Part number RM2L-iC). Specifications The following specifications apply to the RM-iC series readers: Data Cable: Recommended data cable is Belden #9841or equivalent. The maximum length is 4000 feet (1212 meters) between the apc/istar and the RM-4. Power Wiring: Recommended power wiring is Belden #8461/8442 twisted pair. Maximum length depends on the wire gauge. The power source can be from the power supply on an apc or istar or can be a separate local supply. If a separate local supply is used, the ground of the local supply must be connected to the ground of the apc or istar The local power supply must be a UL Listed Access Control (or Burglar Alarm), power-limited, Class 2, power source Power Requirements: 12 VDC, 300 ma Temperature Indoor: 32 F to 120 F (0 C to 49 C) Outdoor: -31 F to 151 F (-35 C to 66 C) 1

2 Installation Qualified on 26-bit, 35-bit, 37-bit, and 32-bit MIFARE serial number formats. UL has only evaluated the 26-bit HID card format for this unit. Standards RM-iC series readers are Underwriters Laboratories Inc. (UL), Listed to Standard UL 294, Access Control System Units, Fifth Edition. RM-iC series readers must be wired in accordance with the National Electrical Code (ANSI/NFPA 70), local codes, and the authorities having jurisdiction. INSTALLATION To install an RM-iC series reader, perform these steps: 1. Install the RM mount plate 2. Wire the components 3. Connect and ground the cable shields on the reader bus 4. Set the RM-4 (reader) address 5. Install the ARM-1 relay boards (optional) 6. Install the heater kit. (optional) 7. Mount the RM-iC standard housing on the RM mount plate using the Software House security screwdriver (Part number ). Install the RM Mount Plate Figure 1 shows the RM-iC standard housing, mount plate, and gasket. All RM-iC series readers conform to the same housing, mount plate, and gasket dimensions. Standard Housing Housing screws Requires a security screwdriver Standard mount plate Gasket FIGURE 1. Standard Housing and Mount Plate 2

3 Installation Figure 2 shows RM mount plate dimensions. 5.45" Wiring access 4.11" 3.66" 2.47" 4.94" 1.29".83" 1.54" 1.82" 2.73" 3.64" 3.92" 8 mounting holes.0.156" Thru, Countersink FIGURE 2. RM Mount Plate Dimensions This device has been approved for outdoor use when properly installed with RM Heater Kit Installation (P.N ) and the supplied gasket material. Position the gasket with the RM mount plate so that the mounting holes are properly aligned. Ensure that the gasket is placed between the mounting surface and mating surface of the RM mount plate. Fasten the RM mount plate to the mounting surface with the gasket material in between. Install the gasket so that no gaps or wrinkles are present. The RM mount plate contains eight mounting holes. However, you do not have to use all eight holes; usually any four of the eight holes are adequate. The mounting holes are and provide clearance for 6-32 flat head counter sunk bolts or screws. 3

4 Installation Wire the RM-4 Components Figure 3 shows RM-4 Connections. FIGURE 3. RM-4 Connections UL has not evaluated the ARM-1. 4

5 Installation Wiring the Inputs, Outputs, Reader Bus Figure 4 shows RM-4 P1 and P5 wiring. FIGURE 4. RM-4 Wiring Requirements SW3-7 and SW3-8 refer to the Beeper on the RM-4. P3 Reader Beep refers to the Beeper on the read head, if it exists. There is no Beeper on the RM-iC read heads. To comply with UL requirements, use shielded, minimum 22 AWG stranded, twisted pair cable for monitor points, DSMs, and REXs. Use Belden 9462 or equivalent. 5

6 RM Series Reader Setup RM SERIES READER SETUP To set up an RM series reader 1. Set the Reader Address Switch, SW1 (a 16 position rotary switch, see Figure 4), to a number from one to eight. Each Reader along the bus must have a unique address. 2. The SW3 Configuration Switches are factory preset for the RM-iC readers, as shown in Table 1. However, you can override SW3-4, SW3-5, and SW3-8, if desired. TABLE 1. SW3 Configuration Switch Settings SW3 # Function Off (Open) On (Closed) SW3-1 Reader type Magnetic Wiegand SW3-2 LCD LCD Present No LCD SW3-3 a LED Option Normal External Bi-color SW3-4 Tamper Normal Bypass SW3-5 (see caution) EOL-Termination Not last Last unit in bus SW3-6 a LED Option Normal One Wire (A,B,C) SW3-7 Beeper Control Enable RM-4 Beeper Disable RM-4 Beeper SW3-8 Beep on Read Control No Beep on Read Beep on Read a. Used only with 3rd party readers connected to an RM-4 module. To properly terminate an RS-485 line, only the last unit on the bus should have SW3-5 in the On (closed) position. 3. Connect P5 input and output wiring, as shown in Table 2 and Figure 7 on page 10. TABLE 2. P5 Input and Output Wiring P5 Function V relay power 2 Relay 1 drive (GND) for first ARM-1 Module 3 Relay 2 drive (GND) for second ARM-1 Module 4 Supervised Input1 5 Supervised Input1 6 Supervised Input2 7 Supervised Input2 6

7 RM Series Reader Setup RM-4 Pre-wired Reader Connections The RM-4 Reader is pre-wired, as shown in Figure 5. FIGURE 5. RM-4 Reader pre-wired Connections The following P3 Reader pins are not used on the RM-iC readers: Mag Clock Mag Data +5VDC RS-485 TXD/RXD + RS-485 TXD/RXD Beep 7

8 RM Series Reader Setup Table 3 shows the P3 read head wiring connections. TABLE 3. Read Head Wiring P3 Wiegand (Swipe or Proximity) 1 Data 1 (white) 2 Data 0 (green) 3 No Connection 4 +5 V (red) Not used on RM-iC 5 Ground (black) V (red) 7 Red LED 8 Yellow LED 9 Green LED 10 RS-485 TXD/RXD+ Not used on RM-iC 11 RS-485 TXD/RXD Not used on RM-iC 12 Read Head Beep Control Not used on RM-iC The RS-485 connection is only for the RM2L It is used to download firmware to the reader. Table 4 indicates the wiring for units with keypads. TABLE 4. Wiring for Units with Keypads J2 Pin Function 1 Col 3 2 Col 2 C3 C2 C1 3 Col 1 4 Col 0 5 Row 3 6 Row 2 R3 R2 R Please note that on a 3 x 4 matrix keypad, Pin 4 (C0) is not used. 7 Row 1 8 Row 0 R0 CMD ENT 0 CE Grounding and Shielding Single RM Reader 8

9 RM Series Reader Setup 1. When connecting a single RM reader to the reader bus, use twisted pair, shielded minimum 24 AWG cable. Attach the shield at one end only, usually at the apc or istar end. 2. Attach a local earth ground (18 or 22 gauge) wire to the J5 component on the RM reader. Multiple RM Bus Devices When wiring an RM reader to a bus with multiple devices, such as other RM-4s, I/8s, or R/8s: 1. Attach the shields along the bus together (insulate each connection). Snip off the shield wire at the end of the bus. See Figure 6 2. Attach the shield to the ground at only one point at the ground stud inside the istar or apc cabinet adjacent to the knockout. 3. Attach a local earth ground (18 or 22 gauge) wire to the J5 component on the RM reader. Ground stud Twist shield wires together and insulate (do not ground) Shield wire ACM module Shield wire Snip off shield wire at end of bus Knockout Enclosure/cabinet RS-485 connector on a reader (bus configuration) FIGURE 6. Reader Shield Wiring Setting Module Address and EOL Termination To set the module address, set SW1 (16 position rotary switch) to a number from one to eight. Every RM-iC series reader on a bus must have a unique address. To set RS-485 EOL (End of Line) termination, set SW3-5 to the On (closed) position if the module is the last unit on the bus. If the module is not the last unit on the bus, SW3-5 should be Off (open). 9

10 RM Series Reader Setup Figure 7 shows how to connect ARM-1 relay modules to the RM-4 outputs and how to wire NO (Normally Open) and NC (Normally Closed) supervised inputs. FIGURE 7. RM-4 Input/Output Connections Maximum distance from P5 to the ARM-1 is 25 feet. Maximum distance from P5 to the inputs is 2000 feet. Locate the 1KΩ resistors for the NO and NC supervised inputs as close as possible to the switch. To comply with UL requirements, use shielded, minimum 22 AWG stranded, twisted pair cable for monitor points, DSMs, and REXs. Use Belden 9462 or equivalent. 10

11 RM Series Reader Setup Installing the ARM-1 Relay Module Two ARM-1 relay components can be connected to the RM-iC series reader through the P5 connector (Table 5 ). RM P5-1 is the common (+12 VDC) pin for either ARM-1. RM P5-2 is the output drive (GND) for the first relay. RM P5-3 is the output drive (GND) for the second relay. TABLE 5. ARM-1 Wiring Module Wiring ARM-1 Relay ARM P2-1 to RM P5-1 ARM P2-2 to RM P5-2 ARM-2 Relay ARM P2-1 to RM P5-1 ARM P2-2 to RM P5-3 The ARM-1 has not been evaluated by UL. Installing the Heater (optional) RM-iC readers require a heater kit (Model ) when installed outdoors in an environment and where temperatures may drop below 40 F (5 C). The Model heater kit contains the following parts: TABLE 6. Heater Parts Quantity Description 1 Transformer 12 VAC 40VA 2 Heater Strips 1 Thermostat (turns on at 40 F) 3 Wire nuts x 1/4 screws to mount thermostat to RM plate. Part # A is supplied without a transformer. A UL Listed Class 2 transformer rated output 12 VAC, 40 VA is required for proper installation. 11

12 RM Series Reader Setup Figure 8 shows how to wire the RM heater kit. FIGURE 8. RM Heater Kit Wiring Figure 9 shows the location of the heater strips and thermostat on the RM mount plate.. FIGURE 9. RM Installation Applying Heater Strips To apply heater strips: 1. Clean the attachment surface of the RM mount plate with a solvent such as alcohol (use all required precautions when handling solvents). 2. Carefully remove the release film from the adhesive. 3. Locate the heater on the clean surface of the RM mount plate exactly as shown in Figure 9 12

13 RM Series Reader Setup 4. Gently roll the heater strip in place to remove air bubbles. 5. For maximum adhesion, do not apply pressure to the heater strips for 72 hours. Air gaps or bubbles under the heater cause localized overheating and possible heater burnout. Also, application of adhesives at temperatures below 50 F is not recommended. Installing the Thermostat To install the thermostat: 1. Fasten the thermostat to the RM mount plate with the body of the device facing the junction box and the face sitting flat against the RM mount plate surface. 2. With the back (or outside) surface facing up, align the thermostat such that the screw holes of the thermostat allow for the 6-32 x 1/4" screws to secure the device to the RM mount plate. 3. Use two (Quantity 2) 6-32 x 1/4" screws to mount the thermostat to the RM mount Plate. Tighten the screws allowing the thermostat to be sufficiently secured to the RM mount plate. Do not over tighten the screws. Power Requirements and Specifications Table 7 lists the power requirements and operating specifications of the RM-4 module. TABLE 7. Power Requirements and Operating Specifications Requirement RM-4 Power requirements Maximum input (with full load) Relay contact power limits Reader LED output control Reader port output voltage Reader port output maximum current Specification +12/24 VDC 175 ma without reader and relays +12/24 VDC 550 ma maximum with reader and relays Up to 30 VAC/DC, 3.3 A maximum 4.0 VDC to 5.25 VDC, 20 ma maximum 5 VDC or 12 VDC 300 ma (at 5V or 12V) 13

14 Testing RM Readers TESTING RM READERS To test RM series readers: 1. Properly configure Readers, Inputs, and Outputs using the C CURE Administration application and put the reader Online. 2. Measure the supply voltage to the RM-4. The voltage can be measured between pin 1 (+12 VDC supply) and pin 4 (ground) on the P4 connector. The voltage must be +12 VDC (+/-5%). 3. Check the RM reader address setting. The RM must be set to an unused address, between 1 and 8, when connected to the apc or istar. Use rotary switch SW1 to set the reader address. 4. Check the RM-4 for communications to the apc or istar by observing LED2 and LED3. 5. Check the supervised inputs. Configure the inputs on the apc or istar using the C CURE Administration application. With no switches or resistors connected to the supervised input 1 and 2 lines, the C CURE Monitoring application should report inputs as Open Loop. When you connect the 1,000-ohm resistor to the input terminals, the C CURE Monitoring application should report that the input as Deactivated. Supervised inputs #1 is found at pins 4 and 5 of P5. Supervised input #2 is found at pins 6 and 7 of P5. 6. Check the outputs. The outputs can be functionally tested by using the momentary activate feature in the C CURE Monitoring application. When the outputs are momentarily activated, the signal will change state for a few seconds. 7. Check the reader interface. The reader interface can only be tested by presenting a card with the appropriate technology to the reader. Reading a card will cause the display to show Access Granted or Access Denied, depending on the clearance of the card. 14

15 Canadian Radio Emissions Requirements CANADIAN RADIO EMISSIONS REQUIREMENTS This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le present appareil numerique n emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class A prescrites dans le Reglement sur le brouillage radiolelectrique edicte par le ministere des Communications du Canada. FCC DIGITAL DEVICE LIMITATIONS Radio and Television Interference This equipment has been tested and found to comply with the limits for a digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and television reception. Caution: Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate this equipment. 15

16 FCC Digital Device Limitations C CURE and Software House are registered trademarks of Tyco International Ltd. and its respective companies. Certain Product names mentioned herein may be trade names and/or registered trademarks of other companies. Information about other products furnished by Software House is believed to be accurate. However, no responsibility is assumed by Software House for the use of these products, or for an infringement of rights of the other companies that may result from their use. RM-iCLASS Series Quick Start Installation Guide Document Number: UM-208 Revision: C0 Print Date: June 2009 This manual is proprietary information of Software House. Unauthorized reproduction of any portion of this manual is prohibited. The material in this manual is for information purposes only. It is subject to change without notice. Software House assumes no responsibility for incorrect information this manual may contain. Copyright 2007 Tyco International Ltd. and its respective companies. All rights reserved. 16