Siemens SICAM TM. Installation DC Preface, Table of Contents. Architecture 1. Components 2. Assembly 3. Wiring Communication

Transcription

1 SICAM TM Installation Preface, Table of Contents Architecture 1 Components 2 Assembly 3 Wiring Communication 4 Wiring for the Reception of Time Signals 5 Wiring Watchdog and Error 6 Power Supply 7 Wiring Peripheral Elements 8 Wiring Process Peripherals 9 Shielding / Protective Earthing 10 Labelling 11 Parameter Setting Preparation 12 A Recommended and tested purchased products Licensing Agreement B Literature DC Siemens

2 Hint Please observe Notes and Warnings for your own safety in the Preface. Disclaimer of Liability Although we have carefully checked the contents of this publication for conformity with the hardware and software described, we cannot guarantee complete conformity since errors cannot be excluded. The information provided in this manual is checked at regular intervals and any corrections that might become necessary are included in the next releases. Any suggestions for improvement are welcome. Copyright Copyright Siemens AG 2014 The reproduction, transmission or use of this document or its contents is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Subject to change without prior notice Document Label: SICRTUs-HBTMACPINSTALL-ENG-V2.04 Release date: Siemens AG Bestellnr.: DC

3 Preface This document is applicable to the following product: SICAM TM Purpose of this manual Target Group This handbook describes how the hardware of a SICAM TM system is to be installed and which preparations are to be made for the subsequent parameter settings. Thereby the following points are described step-by-step: Conception of the architecture Installation of the hardware Label Wiring Conventions used Parameter Setting Preparation This handbook is intended for persons who are entrusted with the design and installation of SICAM TM systems. Outputs visible on the screen aredescribed in this font. Inputs via keyboard or mouse keys and visible on the screen are alsodescribed in this font. Cross references to other chapters or manuals are represented in italics, such as e.g. Common Functions System and Basic System Elements, section "Information Objects". Siemens SICAM TM, Installation 3 DC , Edition

4 Notes on Safety This manual does not constitute a complete catalog of all safety measures required for operating the equipment (module, device) in question because special operating conditions might require additional measures. However, it does contain notes that must be adhered to for your own personal safety and to avoid damage to property. These notes are highlighted with a warning triangle and different keywords indicating different degrees of danger. Danger means that death, serious bodily injury or considerable property damage will occur, if the appropriate precautionary measures are not carried out. Warning means that death, serious bodily injury or considerable property damage can occur, if the appropriate precautionary measures are not carried out. Caution means that minor bodily injury or property damage could occur, if the appropriate precautionary measures are not carried out. Hint is important information about the product, the handling of the product or the respective part of the documentation, to which special attention is to be given. Qualified Personnel Commissioning and operation of the equipment (module, device) described in this manual must be performed by qualified personnel only. As used in the safety notes contained in this manual, qualified personnel are those persons who are authorized to commission, release, ground, and tag devices, systems, and electrical circuits in accordance with safety standards. Use as Prescribed The equipment (device, module) must not be used for any other purposes than those described in the Catalog and the Technical Description. If it is used together with third-party devices and components, these must be recommended or approved by Siemens. Correct and safe operation of the product requires adequate transportation, storage, installation, and mounting as well as appropriate use and maintenance. During operation of electrical equipment, it is unavoidable that certain parts of this equipment will carry dangerous voltages. Severe injury or damage to property can occur if the appropriate measures are not taken: Before making any connections at all, ground the equipment at the PE terminal. Hazardous voltages can be present on all switching components connected to the power supply. Even after the supply voltage has been disconnected, hazardous voltages can still be present in the equipment (capacitor storage). Equipment with current transformer circuits must not be operated while open. The limit values indicated in the manual or the operating instructions must not be exceeded; that also applies to testing and commissioning. 4 SICAM TM, Installation Edition , DC

5 Table of Contents 1. Architecture Mechanical Design Configurations (Examples) Peripheral Elements SICAM TM, electrically connected Peripheral Elements SICAM TM, electrically connected Peripheral Elements SICAM TM, optically connected Peripheral Elements SICAM TM, electrically and optically connected Components Master Control Modules Serial Interface Modules Serial Interface Processor (SIP) Network Interface Processor (NIP) Field Bus Interface Processor (FIP) Bus Interface Module Power Supplies Peripheral Modules Assembly Necessary Material How and where can Installation take place? Installation Location Installation Position Space Requirement Environmental Conditions Installation of TS35 Rail (DIN Rail) Installation of Cable Duct Installation of Master Control Element Removal/Shifting of the Master Control Element Securing Master Control Element against Slipping Installation of Bus Interface Modules Optical Ax Bus Removing/Shifting the Optical Bus Interface Module Electrical Ax Bus Installing TM Modules Design and Elements of a Module Handling Connection Order Siemens SICAM TM, Installation 5 DC , Edition

6 Table of Contents 4. Wiring Communication Introduction Configuring Master Control Element with Serial Interface Modules (SIM) Opening the Housing Removing/Fitting the SIM Retainer Installing Patch Plugs and SIMs Fixing the SIMs Configuration Notes Wiring Communication Serial Communication Point-to-Point Traffic / Multi-Point Traffic via Dedicated Line Modem and WT Channel Modem Multi-Point Traffic via Glass Fibre Optic and Star Connection Analog Dial-up Traffic Westermo TD36 Modem with external Power Supply Dial-up traffic analog/gsm/isdn GSM Dial-up Traffic LAN Communication (Ethernet TCP/IP) Field Bus/Profi Bus Communication Wiring for the Reception of Time Signals DCF77 Receiver GPS Satellite Receiver Wiring for the receipt of the minute pulse Wiring for the receipt of the serial time signal LAN Time Server Wiring Watchdog and Error Introduction Power Supply Introduction Power Supply Master Control Element Power Supply Peripheral Element (Power Supply Module PS-663x) Power Supply Bus Interface Module (CM-0842) Fuse Protection Primary Mains Unit / Standard Type Wiring Peripheral Elements Introduction Master Control Element CP-6014 ó Peripheral Control Module PE Master Control Element CP-6014 ó Bus Interface Module CM-084x Bus Interface Module CM-0843 ó Peripheral Control Module PE SICAM TM, Installation Edition , DC

7 Table of Contents 8.5. Bus Interface Module CM-0842 ó Peripheral Control Module PE-6411, PE Bus Interface Module CM-0842 ó Bus Interface Module CM Wiring Process Peripherals Wiring Process Peripherals Peripheral Connector TE-6450 Wiring the Data Transmission Wiring of analog measured values Shielding / Protective Earthing Shielding Protective Earthing / Grounding Labelling Introduction Labeling Master Control Element Equipment Identification, Region Number, Component Number Plant- and Location Designation Labeling Peripheral Element Region Number, Component Number, PBA Number Plant- and Location Designation Equipment Identification (EI) Terminal Labeling Individual Terminal Point Labeling Terminal Coding Parameter Setting Preparation Introduction Physical connection between SICAM TOOLBOX II and SICAM TM Direct connection via toolbox cable Serial via modem Via Ethernet (TCP/IP) Via Ethernet (TCP/IP) and Terminal Server (serial) Logical Connection between SICAM TOOLBOX II and SICAM TM Flash Card Inserting Flash Card Withdrawing Flash Card A. Recommended and tested purchased products A.1. Modem A.2. DCF77 Accessories A.3. GPS Satellite Receiver / Accessories A.4. LAN Time Server Siemens SICAM TM, Installation 7 DC , Edition

8 Table of Contents A.5. Power Supplies B. Licensing Agreement B.1. Open Source Software used in SICAM TM B.1.1. Readout of ReadmOSS.htm SICAM TM, Installation Edition , DC

9 1. Architecture Content 1.1. Mechanical Design Configurations (Examples) Siemens SICAM TM, Installation 9 DC , Edition

10 RX SI0 SI1 /LK /PK SI2 Architecture 1.1. Mechanical Design A SICAM TM system consists of one master control element, up to a maximum of 4 bus interface modules (electrical and/or optical) and up to 16 peripheral elements. A peripheral element consists of a power supply module, a peripheral control module and up to a maximum of 8 I/O-modules. The modules are fitted on a TS35 rail (DIN rail). Optionally the master control element can be configured with up to 2 serial interface modules (SIM) for the communication with other automation units or control systems. X13 SICAM SI3 SIM0 X3 X6 TM 1703 ACP CP-6014 X7 X8 X9 X10 X4 X11 X12 WD ER X5 COMCPY X15 ER PUSH TO RELEASE X14 X16 X1 SICAM 1703 /LK /PK RY Master control element Bus interface module (electrical) Bus interface module (optical) X2 PUSH TO RELEASE NC M-PRE/0 SI0 ERx TX M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) M-PRE/3 SI3 PUSH TO UNLOCK PWR 24-60VDC TB FB LOC RES Max. 8 I/O-modules Peripheral control module (elektrical or optical) TS35 rail Power supply module 10 SICAM TM, Installation Edition , DC

11 X2 X3 TB X6 NC Architecture 1.2. Configurations (Examples) Peripheral Elements SICAM TM, electrically connected SICAM TM 1703 ACP CP-6014 X1 X11 X4 X13 X12 X15 X14 X16 X7 SI0 X8 X9 SI3 FB RX LOC S I0 S I1 /LK S I2 S I3 /LK WD X5 ER SI M0 /PK X10 /PK RY RE S CP-6014 PUSH TO RELEASE M-PRE/0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) M-PRE/3 E Rx TX PUSH TOUNLOCK PWR 24-60VDC E R COMCPY PUSHTO RELEASE Communication with other automation units Ax 1703 peripheral bus (electrical) 16 Mbps USB cable, length up to 3 m PE-6410 PS-663x max. 8 I/O-modules Siemens SICAM TM, Installation 11 DC , Edition

12 X2 X3 TB X6 NC X7 SI0 X8 X9 SI3 X4 FB RX LOC S I0 S I1 /LK S I2 S I3 /LK /PK WD /PK X5 RY ER RE S X1 Architecture Peripheral Elements SICAM TM, electrically connected PUSH TO RELEASE SICAM TM 1703 ACP CP-6014 M-PRE/0 SIM0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) X10 M-PRE/3 X11 X12 PUSH TOUNLOCK E Rx TX E R COMCPY X15 PWR 24-60VDC PUSH TO RELEASE X13 X14 X16 CP-6014 Note: all in all up to 16 peripheral elements Ax 1703 peripheral bus (electrical) 16 Mbps patch cable, length up to 3 m Communication with other automation units CM-0843 Ax 1703 peripheral bus (electrical) 16 Mbps USB cable, length up to 3 m PE-6410 PS-663x max. 8 I/O-modules 12 SICAM TM, Installation Edition , DC

13 X2 X3 TB X6 NC X7 Architecture Peripheral Elements SICAM TM, optically connected SICAM 1703 SI0 X8 X9 SI3 X4 FB RX LOC S I0 S I1 /L K S I2 /PK WD S I3 /L K /PK X5 RY ER RE S X1 PUSH TO RELEASE SICAM TM 1703 ACP CP-6014 M-PRE/0 SIM0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) X10 M-PRE/3 X11 X12 PUSH TOUNLOCK E Rx TX E R COMCPY X15 PW R 24-60VDC PUSHTO RELEASE X13 X14 X16 CP-6014 Note: all in all up to 16 peripheral elements Ax 1703 peripheral bus (electrical) 16 Mbps patch cable, length up to 3 m Communication with other automation units SICAM 1703 CM-0842 Ax 1703 peripheral bus (optical) 16 Mbps, optical fibre, length up to 200 m PE-6411 PS-663x max. 8 I/O-modules Siemens SICAM TM, Installation 13 DC , Edition

14 X2 Architecture Peripheral Elements SICAM TM, electrically and optically connected SICAM 1703 X1 SICAM TM 1703 ACP CP-6014 X11 X4 X12 X15 X14 X16 X13 X3 TB X6 NC X7 SI0 X8 X9 SI3 FB WD X5 ER SIM0 X10 RX LOC SI0 SI1 /L K SI2 SI3 /L K /PK /PK RY ERx TX M-PRE/0 M-PRE/1 SI1(ETO) M-PRE/2 SI2(FB) RES M-PRE/3 E R C OMC PY PUSH TO REL EASE CP-6014 Note: all in all up to 16 peripheral elements SICAM 1703 PUSH TO REL EASE PUSH TOUNLOCK PWR 24-60VDC communication with other automation units Ax 1703 peripheral bus (electrical) 16 Mbps patch cable, length up to 3 m CM-0842 CM Ax 1703 peripheral bus (electrical) 16 Mbps USB cable, length up to 3 m Ax 1703 peripheral bus (optical) 16 Mbps, optical fibre, length up to 200 m PE-6410 PS-663x max. 8 I/O-modules PE-6411 PS-663x max. 8 I/O-modules 14 SICAM TM, Installation Edition , DC

15 2. Components Content 2.1. Master Control Modules Serial Interface Modules Bus Interface Module Power Supplies Peripheral Modules Siemens SICAM TM, Installation 15 DC , Edition

16 Components 2.1. Master Control Modules Designation CP6014 Master Control Module Item Number/ MLFB GC MF11130GA140AA0 16 SICAM TM, Installation Edition , DC

17 Components 2.2. Serial Interface Modules Serial Interface Processor (SIP) Designation SM-2551 Serial Interface Processor 2 SI Item Number/ MLFB BC MF10130CF510AA0 SM-0551 Serial Interface Processor 1 SI BC MF10130AF510AA Network Interface Processor (NIP) Designation SM-2557 Network-Interf.Ethernet 2x100TX Item Number/ MLFB BC MF10130CF570AA0 SM-2558 Ethernet-Interf. 1x100TX + 1 serial interface optional BC MF10130CF580AA0 Siemens SICAM TM, Installation 17 DC , Edition

18 Components Field Bus Interface Processor (FIP) Designation SM-2545 Profibus Interface (Master) Item Number/ MLFB BA MF10110CF450AA0 18 SICAM TM, Installation Edition , DC

19 Components 2.3. Bus Interface Module Designation CM-0843 Ax 1703 bus interface electrical Item Number/ MLFB GA MF11110AJ430AA0 CM-0842 Ax 1703-Businterface 4x fiber optical GA MF11110AJ420AA Power Supplies Designation PS-6630 Power Supply Module VDC (EMC+) Item Number/ MLFB GC MF11130GG300AA0 PS-6632 Power Supply Module VDC (EMC+) GC MF11130GG320AA0 Siemens SICAM TM, Installation 19 DC , Edition

20 Components 2.5. Peripheral Modules PE-6410 Peripheral Control Module Ax-PE-Bus (electrical) GC MF11130GE000AA0 PE-6411 Peripheral Controller (1x Ax-PE bus opt) GC MF11130GE110AA0 PE-6412 Peripheriekopplung (2x Ax-PE Bus opt) GC MF11130GE120AA0 DI-6100 Binary Input 2x8, 24-60VDC GC MF11130GB000AA0 DI-6101 Binary Input 2x8, 110/220VDC GC MF11130GB010AA0 20 SICAM TM, Installation Edition , DC

21 Components DI-6102 Binary Input 2x8, 24-60VDC 1ms GC MF11130GB020AA0 DI-6103 Binary Input 2x8, 110/220VDC 1ms GC MF11130GB030AA0 DI-6104 Binary Input 2x8, 220VDC GC MF11130GB040AA0 DO-6200 Binary Output Transistor 2x8, 24-60VDC GC MF11130GC000AA0 DO-6212 Binary Output Relays 8x VDC/230VAC GC MF11130GC200AA0 Siemens SICAM TM, Installation 21 DC , Edition

22 Components DO-6220 Command Out Basic Module GC MF11130GC200AA0 DO-6221 Command Out Basic Module Measure GC MF11130GC210AA0 DO-6230 Command Out Relay Module GC MF11130GC300AA0 AI-6300 Analog Input 2x2 ±20mA/±10V GC MF11130GD000AA0 AI-6307 Analog Input 2x2 ±5mA GC MF11130GD070AA0 22 SICAM TM, Installation Edition , DC

23 Components AI-6310 Analog Input 2x2 Pt100/Ni100 GC MF11130GD100AA0 AO-6380 Analog Output 4x ±20mA/±10mA/±10V GC MF11130GD800AA0 TE-6420 Speed Measurement 2x2 5VDC/24VDC/NAMUR GC MF11130GE200AA0 TE-6450 Position Acquisition 2x2 SSI/RS-422 GC MF11130GE500AA0 Siemens SICAM TM, Installation 23 DC , Edition

24

25 3. Assembly Content 3.1. Necessary Material How and where can Installation take place? Installation of TS35 Rail (DIN Rail) Installation of Cable Duct Installation of Master Control Element Installation of Bus Interface Modules Installing TM Modules Siemens SICAM TM, Installation 25 DC , Edition

26 Assembly 3.1. Necessary Material Due to the different circumstances with the local installation of the SICAM TM systems, not all details such as e.g. screw sizes, cable lengths and the like can be dealt with in this document. Therefore only recommendations and minimum requirements are specified concerning consumables. The fitter himself must ensure that suitable materials and tools necessary for the installation are available. 26 SICAM TM, Installation Edition , DC

27 X2 X3 TB Assembly 3.2. How and where can Installation take place? Installation Location The terminal modules are designed for the installation in a cabinet, rack or on the wall Installation Position SICAM TM systems may only be installed horizontally or vertically. The vertical installation is to be preferred, since this provides a considerably more space-saving and efficient installation. The cabling of external cables is also made significantly easier as a result. SICAM TM 1703 ACP CP-6014 SICAM 1703 X1 X11 X4 X13 X12 X15 X14 X16 X6 NC X7 X8 X9 WD X5 ER SIM0 X10 RX /L K /PK /L K /PK ERx T X FB LOC SI0 SI1 SI2 SI3 M-PRE/0 M-PRE/1 SI 1 (E TO) M-PRE/2 SI 2 (FB ) SI 0 M-PRE/3 SI 3 ER PUSH TO UNLOCK PWR 24-60VDC COM CPY RY RES PUSH TO RELEASE PUSH TO REL EASE horizontal installation vertical installation Not permissible are installations on the ceiling (own weight) and on the floor (dust level). Siemens SICAM TM, Installation 27 DC , Edition

28 X3 TB X6 NC X7 X8 X9 Assembly Space Requirement The space requirement of a completely configured SICAM TM peripheral element (power supply, master control unit, up to 8 I/O modules) in the width comes to 630 mm (without end bracket and terminal strip marker for the system designation). The space requirement for the height depends on several factors. Besides the size of the module itself (130mm), the size of the cable ducts used and their minimum distance to the modules is to be taken into account. This distance is 20 mm if no lead labeling is to take place and 30 mm if the leads are to be fitted with labeling bushes HÖHE X4 FB RX SI0 SI1 /LK SI2 /PK SI3 /LK /PK X5 RY ER PUSH TO RELEAS E X2 SICAM TM 1703 ACP CP-6014 M-PRE/0 SI0 SIM0 M-PRE/1 SI1(ETO) M-PRE/2 SI2(FB) X10 M-PRE/3 SI3 X11 X12 PUSH TO UNLOCK ERx TX LOC WD ER COMCPY X15 RES PWR 24-60VDC PUSHTO RE LEA SE X13 X14 X16 X1 SICAM or or or HEIGHT (mm) DEPTH (mm) (system with 8 I/O modules) WIDTH (mm) 28 SICAM TM, Installation Edition , DC

29 Assembly Environmental Conditions The permissible temperature range for the operation of the modules is about C (except CM-0842, only up to +55 C). For details on the subject of environmental conditions, please refer to the SICAM TM System Data Sheet (MC ), chapter: "Climatic Ambient Conditions and Electrical Ambient Conditions". Siemens SICAM TM, Installation 29 DC , Edition

30 Assembly 3.3. Installation of TS35 Rail (DIN Rail) For the installation of the modules a TS35 rail is used. This must conform to the European standard EN The orientation and position in which the TS35 rail is to be installed must be determined locally. Take into account the details specified in chapter 3.2.3, "Space Requirement" Caution By means of the connection TS35 rail - cabinet/rack a reliable grounding connection must be guaranteed. 30 SICAM TM, Installation Edition , DC

31 Assembly 3.4. Installation of Cable Duct For the cabling, cable ducts are to be provided at both sides of the modules. The minimum distance from the terminal module to the cable duct is 20 mm for cabling without lead labeling. If the leads are to be fitted with labeling bushes, the minimum distance is 30 mm (refer to chapter 3.2.3, "Space Requirement" ). Siemens SICAM TM, Installation 31 DC , Edition

32 Assembly 3.5. Installation of Master Control Element The master control element can be installed on the TS35 rail by hand, without any tools. To do this, the master control element is attached to the upper edge of the TS35 rail in a slanted position. One then turns the housing until the white spring retainer has contact with the lower edge of the rail. By pressing on the housing the spring retainer opens a little and the housing snaps into the guide SICAM TM, Installation Edition , DC

33 Assembly Removal/Shifting of the Master Control Element To remove the master control element again, or to change its position on the TS35 rail, the spring retainers on the back panel of the housing must be opened. To do this, one inserts a slotted-screw screw-driver below the housing in the spring retainer and pushes the screw-driver upwards. As a result, the spring retainer opens and is held in a slightly tilted position. As soon as both spring retainers are in this position the master control element can be removed or shifted on the rail After shifting the master control element the spring retainers must be closed again in order to fix the housing. For this a slight push on the spring retainer is sufficient to bring it back to the closed position. 4 Siemens SICAM TM, Installation 33 DC , Edition

34 Assembly Securing Master Control Element against Slipping If the master control element is installed vertically, it must be secured against slipping with an end bracket. 34 SICAM TM, Installation Edition , DC

35 Assembly 3.6. Installation of Bus Interface Modules Optical Ax Bus Designation CM-0842 Ax 1703-Businterface 4x fiber optical Item Number/ MLFB GA MF11110AJ420AA0 The optical Ax Bus Interface Module can be installed on the TS35 rail by hand, without any tools. To do this, the module is engaged in a slanted position with the carrier rail retainer in the upper edge of the TS35 rail. One then turns the housing until the carrier rail retainer also has contact with the lower edge of the rail. By pressing on the housing the retainer opens a little and the housing snaps into the guide Siemens SICAM TM, Installation 35 DC , Edition

36 Assembly Removing/Shifting the Optical Bus Interface Module To remove the optical bus interface module again, or to change its position on the TS35 rail, the carrier rail retainer on the back panel of the housing must be opened. One achieves this by pushing with one finger from above on the moving part of the carrier rail retainer, or from below with one finger hooked into this movable part and pulling downward. In both cases the carrier rail retainer opens and the module can be removed or shifted Electrical Ax Bus Designation Ax 1703 bus interface electrical Item Number/ MLFB GA MF11110AJ430AA0 The electrical Ax Bus Module can be installed on the TS35 rail and removed again by hand, without any tools. For details concerning the handling of a TM module refer to section 3.7, Installing TM Modules. 36 SICAM TM, Installation Edition , DC

37 Assembly 3.7. Installing TM Modules Design and Elements of a Module Peripheral connector On the modules there are, depending on the type, up to 4 10-pole male connectors with removable screw terminals. (Optionally spring-loaded- or crimp terminals can be used.) With the screw terminal, as an option there exists the possibility of a mechanical terminal coding (refer to chapter 11.6; "Terminal Coding"). Connection Diagrams These are located on the underside of the modules. They indicate examples of the external circuitry of the modules. Siemens SICAM TM, Installation 37 DC , Edition

38 Assembly Locking Clips By means of these two metal clips the modules are locked onto the TS-35-rail and also removed. Display Elements / Front Panel The number and meaning of the displays on the front panel are, apart from the RY-LED, different on all modules. While the RY-LED always displays the functional readiness of the module, the meaning of the other displays is to be taken from the respective description (SICAM TM I/O Modules) Handling The modules can be installed on the TS35 rail and removed again by hand, without any tools. For this, the locking clips on the top side of the module are pressed together, the module coupled with the neighboring module by means of the guides at the corners of the housing and positioned on the TS35 rail. For the removal, the locking clips are again pressed together and the module withdrawn with clips pressed together. Warning The connecting and withdrawal of modules is only permitted in a de-energized state. This state is achieved by interrupting the power supply to the power supply unit and to the peripherals. 38 SICAM TM, Installation Edition , DC

39 Assembly Connection Modules that are adjacent to each other are mechanically connected with each other by means of the guides at the corners of the housing. Caution The housing form of older TM modules does not provide sufficient protection against incorrectly positioned installation. Therefore pay attention to the correct alignment if you install such modules. It is correct, when with vertical installation position of the system, the lettering on the front panel can be read from left to right. With horizontal installation position of the system, it must be possible to read the lettering on the front panel from botton to top. Siemens SICAM TM, Installation 39 DC , Edition

40 Assembly Order The first two modules are always the power supply module and the peripheral control module. Afterwards the I/O modules are installed. Caution With the last module, to protect the bus a protective cap is to be snapped on. Such a protective cap is included in the package of every power supply module as standard. In addition, with vertical installation an end bracket is also to be fitted. This prevents the modules from shifting due to their own weight. Designation Endhalter Clipfix 35 Item Number PHO SICAM TM, Installation Edition , DC

41 4. Wiring Communication Content 4.1. Introduction Configuring Master Control Element with Serial Interface Modules (SIM) Wiring Communication Siemens SICAM TM, Installation 41 DC , Edition

42 Wiring Communication 4.1. Introduction Depending on the protocol elements incorporated in the master control element, SICAM TM provides different methods of communication (Serial V.28, V.11; Ethernet TCP/IP; Field Bus) to external data transmission systems. Serial communication Point-to-point traffic according to IEC Multi-point traffic according to IEC Dial-Up Traffic LAN communication Field bus communication This chapter describes how these methods of communication can be realized by means of standard modems and cables. 42 SICAM TM, Installation Edition , DC

43 Wiring Communication 4.2. Configuring Master Control Element with Serial Interface Modules (SIM) A master control element can be configured with up to 2 serial interface modules. The SIMs and the associated patch plugs are installed on the main board of the master control element. In order to perform this task the housing of the master control element must be opened. ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES Siemens SICAM TM, Installation 43 DC , Edition

44 Wiring Communication Opening the Housing First the dust protection cap must be removed from the D-Sub connector (X2) and the screws removed marked with Point. Then the red plastic side panel can be removed by carefully bending it away from the front side of the housing and detaching it from the mounting with a push to the rear. Now the back panel of the housing can be removed and one can begin with the installation of the SIMs SICAM TM, Installation Edition , DC

45 Wiring Communication Removing/Fitting the SIM Retainer The SIM cards are fixed to the main board with 2 clips. To remove these clips one presses that end of the clip, which is snapped on to the underside of the housing, inwards and then by pulling the clip one withdraws it from the housing. Siemens SICAM TM, Installation 45 DC , Edition

46 Wiring Communication Installing Patch Plugs and SIMs On the main board there are 4 slots (X24-X27) for patch plugs and 2 slots for SIMs. The slots X24 and X25 are reserved for SIM0 and X26 and X27 are reserved for SIM1. First the patch plugs must be fitted, since their slots are hidden after installing SIM0. If a second SIM (on slot SIM1) is installed later in a master control element, SIM0 must be removed in order to reach the patch plugs for SIM1. X27 (SI3) X26 (SI2) X25 (SI1) X24 (SI0) SIM0 SIM1 Attention With the CP-6003 master control element the danger exists that patch plugs could be fitted incorrectly, since no mechanical protection exists against distorted installation. This protection is available in CP-6010 and CP A patch plug is then correctly fitted when PIN 1 of the patch plug is slotted in the hole of the respective slot marked with SICAM TM, Installation Edition , DC

47 Wiring Communication Fixing the SIMs In addition to the 3 connectors with which the SIMs are connected with the main board, fixing clips are also used so that the SIMs cannot loosen. To fit these fastening clips, one first guides the wide end of the clip in the recess on the inside of the housing and then presses the thin end, possibly with the help of a narrow screwdriver, into the anchoring between SIM card and housing. Siemens SICAM TM, Installation 47 DC , Edition

48 Wiring Communication The clip is only then correctly fixed, when it snaps on to the housing and presses on the SIM card. Mounting SM-0551 SIM SM-0551 is not mounted directly on the main board like the other SIM, it must be mounted on a SM-2558 before. SM-2558 SM SICAM TM, Installation Edition , DC

49 Wiring Communication Configuration Notes Depending on the type of SIM used and the slot in which this is installed, there are interfaces available on the front of the housing. Which of these interfaces is assigned to which SIM and in which slot the associated patch plug must be plugged in is shown in the following table: SIM-Type Slot Interfaces on Front of Housing Slots for Patch Plugs on Main Board SM-2551 (SIP) SIM0 SI0 SI1 X24 X25 SIM1 SI2 SI3 X26 X27 SM-2558 (NIP) SIM0 SI1 X25 SIM1 SI3 X27 SM-2557 (NIP) SIM0 SI0 SI1 X24 X25 SIM1 SI2 SI3 X26 X27 SM-2545 (FIP) 2) SIM1 SI2 X26 SM-0551 (SIP) 1) SIM0 1) SI0 SI2 X24 X26 1) SM-0551 must be mounted on SM ) Due to thermal rasons only one SM-2545 (on SIM1) may be equipped Siemens SICAM TM, Installation 49 DC , Edition

50 Wiring Communication 4.3. Wiring Communication Hint Communication cables are, if possible, to be installed separately from the supply and peripheral cables. 50 SICAM TM, Installation Edition , DC

51 TB FB R X S I0 S I1 /LK S I2 /PK S I3 /LK /PK RY Wiring Communication Serial Communication Point-to-Point Traffic / Multi-Point Traffic via Dedicated Line Modem and WT Channel Modem CE-070x Master control element CP-6014 PUSH TO R ELE ASE X2 X3 NC X6 SICAM TM 1703 ACP CP-6014 X7 M-PRE /0 SI0 SIM0 X8 M-PRE /1 SI1 (ETO) X9 M-PRE /2 SI2 (FB ) X10 M-PRE /3 SI3 X4 X11 X12 PUSH TO UNLOCK ERx TX LOC ER C OM C PY WD X5 X15 ER R ES PWR VD C PUSH TO RE LEAS E X13 X14 X16 X1 SM-2551 or SM-0551 on SM-2558 CM-2860 V.24/V.28 (X1) SI0-3 Patch cable 0.3m Accessories Designation CE-0700 V.23 dedicated line modem Item Number/ MLFB G MF11020BC000AA0 CE WT channel modem f. DIN-rail G MF11020CA810AA0 TPP_0.3M TP Patch Cable 0.3m Cat 5 T MF13040BC570AA0 Siemens SICAM TM, Installation 51 DC , Edition

52 TB FB R X SI 0 SI 1 /LK /PK SI 2 SI 3 /LK /PK R Y X1 Wiring Communication Multi-Point Traffic via Glass Fibre Optic and Star Connection PS-66xx CM-0822 Glass fibre optic max. 1.5 km Master control element CP-6014 SM-2551 or SM-0551 on SM-2558 CM-0827 PUSH T O R ELEA SE X2 X3 NC X6 SICAM TM 1703 ACP CP-6014 X7 M-PRE/0 SI0 SIM 0 X8 M-PRE/1 SI1 (E TO) X9 M-PRE/2 SI2 (FB) X10 M-PRE/3 SI3 X4 X11 X12 PU SH TO UNLOCK E Rx TX LOC E R COM C PY WD X5 X15 E R RE S PWR 24-60VDC PUSH TO R ELE AS E X13 X14 X16 CM-2860 SI0-3 Accessoires Designation CM Fiberoptik-Interface (el.- LWL) Item Number/ MLFB GA MF11110AJ270AA0 Fibre optics length: max. 0,5km Fibre optics length: max. 1,5km FO-INDOORCABLE-50-DUP-LSOH FO-OUTDOORCABLE-50-2FIB-ARM FO-CONNECTOR-ST-50/62 FO-INDOORCABLE-62-DUP-LSOH FO-OUTDOORCABLE-62-2FIB-ARM FO-CONNECTOR-ST-50/62 TF7-027 TF7-028 TF7-016 TF7-006 TF7-007 TF SICAM TM, Installation Edition , DC

53 TB NC SI0 SI3 FB RX SI 0 SI 1 /LK X1 Wiring Communication Analog Dial-up Traffic X6 SICAM TM 1703 ACP CP-6014 X7 SIM0 X8 X9 X10 X4 X11 X12 WD X5 X15 PUSH TO RELE AS E X14 X16 X1 3 / PK SI 2 SI 3 /LK / PK RY ER Eurocom 24 Modem SM-2551 or SM-0551 on SM-2558 CM-2860 X2 X3 Master control element CP-6014 X2 ERx TX LOC M-PRE/0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) M-PRE/3 PUSH TO UNLOCK PWR 24-60VDC E R COMCPY RE S PUSH T O RE LEA SE max. 300 mm SI0-3 Accessories see Appendix A, Recommended and tested purchased products Cable Circuitry Master Control Element Eurocom 24 Modem CP-6014 Siemens SICAM TM, Installation 53 DC , Edition

54 TB FB RX SI0 SI1 /LK /PK Wiring Communication Westermo TD36 Modem with external Power Supply X3 SICAM X6 TM 1703 ACP CP-6014 X7 X8 X9 X10 X4 X11 X12 WD X5 X15 ER PUSH TO RELEASE X14 X16 X1 SIM0 SI2 SI3 /LK /PK RY Westermo TD-36 SM-2551 or SM-0551 on SM-2558 Master control element CP WESTERMO TD-36 PSTN CM-2860 ERx TX LOC ER COMCPY RES POWER PUSH TO RELEASE X2 NC M-PRE/0 SI0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) M-PRE/3 SI3 PUSH TO UNLOCK PWR 24-60VDC X13 Power supply max. 25 m SI VAC / VDC (TD-36 AV) 10-30VAC / 10-60VDC (TD-36 LV) Accessories see Appendix A, Recommended and tested purchased products Cable Circuitry Master Control Element Westermo TD SICAM TM, Installation Edition , DC

55 X3 TB X6 X7 X8 X9 X4 FB RX SI0 SI1 /LK /PK SI2 SI3 /LK /PK RY Wiring Communication Dial-up traffic analog/gsm/isdn Westermo IDW-90 SM-2551 or SM-0551 on SM-2558 Master control element CP-6014 WESTERMO IDW-90 ISDN RS-232 CM-2860 PUSH TO RELEASE X2 SICAM NC TM 1703 ACP CP-6014 M-PRE/0 SI0 SIM0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) X10 M-PRE/3 SI3 X11 X12 PUSH TO UNLOCK ERx TX LOC ER COM CPY WD X5 X15 ER RES PWR 24-60VDC PUSH TO RELEASE X13 X14 X16 X1 Power supply max. 25 m SI VAC / 12-34VAC (IDW-90 LV) Accessories see Appendix A, Recommended and tested purchased products Cable Circuitry Master Control Unit Westermo IDW-90 Siemens SICAM TM, Installation 55 DC , Edition

56 X2 TB NC FB RX SI0 SI1 /LK /PK Wiring Communication GSM Dial-up Traffic SICAM TM 1703 ACP CP-6014 X4 X11 X12 X15 PUSH TO RE LEA SE X14 X16 X1 X13 ER X3 X6 X7 X8 X9 X10 WD X5 SIM0 SI2 SI3 /LK /PK RY VDC (Siemens TC35) SM-2551 or SM-0551 on SM-2558 Master control element CP-6014 Power supply CM-2860 ERx TX LOC M-PRE/0 SI0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) M-PRE/3 SI3 PUSH TO UNLOCK PWR 24-60VDC ER COMCPY RES PUSH TO R ELE ASE GSM Modem SI0-3 Accessories see Appendix A, Recommended and tested purchased products Cable Circuitry Master Control Unit GSM Modem Variant for the deactivation function of the TC35 GSM modem controlled by SICAM RTUs. 56 SICAM TM, Installation Edition , DC

57 Wiring Communication Variant without the deactivation function of the TC35 GSM modem controlled by SICAM RTUs. Siemens SICAM TM, Installation 57 DC , Edition

58 TB FB RX SI0 SI1 /LK /PK SI2 SI3 /LK /PK ER X1 Wiring Communication LAN Communication (Ethernet TCP/IP) Steuerkopfelement CP-6014 CM-2860 X3 SICAM X6 TM 1703 ACP CP-6014 X7 X8 X9 X10 X4 X11 X12 ERx TX LOC COM CPY RY RES WD X5 X15 ER PUSH TO RELEASE X14 X16 SM-2558 Network Interface PUSH TO RELEASE X2 NC M-PRE/0 SI0 SIM0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) M-PRE/3 SI3 PUSH TOUNLOCK PWR 24-60VDC X13 Patchkabel M-PRE/1 SI1 (ETO) Ethernet TCP/IP Switch Accessoires Designation Patch cable CAT5 (4x2) AWG26/7 (used for cabinet-internal wirings up to 10m) Patch cable CAT5 (4x2x0.5) AWG24 (used for cabinet-external wirings up to 100m) Details for connections over 10m can be taken from document: Configuration Automation Units and Automation Networks (DC2-021); Appendix A; Chapter: Electrical Connection, Cable longer than 10m. Item Number / MLFB T (1m) 6MF13040BC550AA0 T (2m) 6MF13040BC510AA0 T (3m) 6MF13040BC520AA0 T (5m) 6MF13040BC530AA0 T (10m) 6MF13040BC540AA0 TF MF13140FB010AA0 TF5-200 (1.5m) 6MF13140FC000AA0 TF5-201 (3m) 6MF13140FC010AA0 TF5-202 (5m) 6MF13140FC020AA0 58 SICAM TM, Installation Edition , DC

59 X3 TB X6 X7 X8 X9 X4 FB Wiring Communication Field Bus/Profi Bus Communication The field bus/profi bus can be connected on the master control element on the X4 DSUBconnector or X9/SI2 RJ45 connector. SICAM TM 1703 ACP CP-6014 X11 X1 2 ER X5 C O MC PY X15 PUSH T O RE L EA SE X14 X16 X1 X13 WD ER RX S I0 S I1 / L K S I2 / PK S I3 / L K X1 0 SI M0 / PK RY Master control element CP-6014 SM-2545 Feldbus/Profibus Interface CM-2869 X2 ERx TX L O C PUSH TO RE L EAS E N C M-PR E/0 SI 0 M-PR E/1 SI 1 (ETO) M-PR E/2 SI 2 (FB) M-PR E/3 SI 3 PUSH TO UN LOCK R ES PWR VDC M-PRE/2 SI2 (FB) FB (X4) Fieldbus/Profibus cable with RJ45 connector Fieldbus/Profibus cable with DSUB connector Fieldbus/Profibus Patch Plug Patch Plug CM-2869 is used for fieldbus/profibus communikation. It is enclosed with SIM SM Designation CM-2869 Patch Plug SMI-RS485 Item Number/ MLFB CA MF12112CJ600AA0 The latest version of this patch plug, item number CA2-869-B, is already modified according to following illustration (thick line). This modification must be added on older versions of the patch plug. Siemens SICAM TM, Installation 59 DC , Edition

60 Wiring Communication 60 SICAM TM, Installation Edition , DC

61 5. Wiring for the Reception of Time Signals Content 5.1. DCF77 Receiver GPS Satellite Receiver LAN Time Server Siemens SICAM TM, Installation 61 DC , Edition

62 RX SI0 SI1 /LK /PK SI2 SI3 /LK /PK RY Wiring for the Reception of Time Signals 5.1. DCF77 Receiver The DCF77 receiver is designed for the installation on a TS35 rail and can be slotted directly on to the master control element (X2) via the 9-pin DSUB-connector. Via this plug-in connection the module is supplied with 5V and a minute pulse is transmitted to the CP-6014 for the synchronization. In addition there is a 2-pole screw terminal (X11 SYNC) available over which, according to requirements, the minute pulse or a serial time signal can be transmitted. DCF77 Road antenna DCF77- Receiver Master control element CP-6014 N connector RG58 SICAM TM 1703 ACP CP-6014 X4 X11 X12 ER X5 COMCPY X15 ER RES PUSH T O RELEASE X14 X16 X1 X13 X3 X6 X7 X8 X9 X10 ERx TX X2 WD SIM0 PUSH TO REL EASE LOC NC M- PRE/0 SI0 M- PRE/1 SI1 (ETO ) M- PRE/2 SI2 (FB) M- PRE/3 SI3 PUSH TO UNLO CK PWR 24-60VDC TB FB Lightning protection X11 SYNC BNC-Connector RG58 Designation DCF77- Receiver for DIN rail Item Number/ MLFB GA MF11110AJ060AA0 Accessories see Appendix A, Recommended and tested purchased products 62 SICAM TM, Installation Edition , DC

63 X2 TB NC FB RX SI0 SI1 /LK /P K SI2 SI3 /LK /P K RY ER Wiring for the Reception of Time Signals 5.2. GPS Satellite Receiver The GPS164 satellite receiver offers a minute pulse and a serial time signal. The settings are made with software GPSMON32. This software is delivered with the GPS164 receiver Wiring for the receipt of the minute pulse The minute pulse is supplied on the screw terminal on the front panel of the GPS164 receiver. GPS167 Antenna/converter RG58 Lightning Protection Antenna connecting kit GPS164 Receiver Master control element CP-6014 Power Supply 24 VDC 4 4 PUSH TO RE LE ASE X3 SICAM X6 TM 1703 ACP CP-6014 X7 M-PRE/0 SI0 SIM0 X8 M-PRE/1 SI1 (ETO) X9 M-PRE/2 SI2 (FB) X10 M-PRE/3 SI3 X4 X11 X12 PUSH TO UNL OCK ERx TX LOC ER COMCPY WD X5 X15 R ES PWR VDC PUSH TO R ELEASE X13 X14 X16 X1 Accessories see Appendix A, Recommended and tested purchased products X11 SYNC Siemens SICAM TM, Installation 63 DC , Edition

64 TB NC FB RX SI 0 Wiring for the Reception of Time Signals Wiring for the receipt of the serial time signal The serial time signal is supplied on the COM 0 interface on the front panel of the GPS164 receiver. The necessary adjustments for the SAT-STRING must be made with software GPSMON32 as follows: Format 7E2 Baud rate 2400 Serial time signal per second 24 VDC 4 4 SICAM TM 1703 ACP CP-6014 X4 X11 X12 X15 PUSH TO RE LEAS E X14 X16 X1 X13 S I1 /LK S I2 /PK SI 3 /LK /PK ER X3 X6 X7 X8 X9 X10 WD X5 SIM0 RY GPS167 Antenna/converter RG58 Lightning Protection Antenna connecting kit 24 VDC GPS164 Receiver Master control element CP-6014 Power Supply X2 PU SH TO RE LEA SE ERx TX LOC ER COMCPY M-PRE/0 SI0 M-PRE/1 SI1(ETO) RES M-PRE/2 SI2(FB) M-PRE/3 SI3 PU SH TO U NLOC K PWR 24-60VDC COM 0 X11 SYNC Accessories see Appendix A, Recommended and tested purchased products Wiring cable GPS164 CP-6014 GPS164 (COM 0) TxD RxD GND 9 pol. DSUB male CP-6014 X11/+ X11/- 64 SICAM TM, Installation Edition , DC

65 X2 TB NC FB Wiring for the Reception of Time Signals 5.3. LAN Time Server NTP Server in 19" case for TCP/IP networks with integrated HTTP-Server. The internal reference time is derived from a built-in GPS receiver of the type GPS167. SICAM TM 1703 ACP CP-6014 X4 X11 X12 WD X15 PUSH TO RELEASE X14 X16 X1 ER X3 X6 X7 X8 X9 X10 X5 RX SI0 /LK /PK /LK /PK ERx TX LOC SI1 SI2 SI3 RY Master control element CP-6014 ER COMCPY RES SM-2557, SM-2558 Network Interface PUSH TO RELEASE M-PRE/0 SI0 SIM0 M-PRE/1 SI1 (ETO) X13 M-PRE/2 SI2 (FB) M-PRE/3 SI3 PUSH TO UNLOCK PWR 24-60VDC Ethernet TCP/IP Hub LAN time server SI1 (ETO) Siemens SICAM TM, Installation 65 DC , Edition

66 Wiring for the Reception of Time Signals 66 SICAM TM, Installation Edition , DC

67 6. Wiring Watchdog and Error Content 6.1. Introduction Siemens SICAM TM, Installation 67 DC , Edition

68 X2 TB F B RX Wiring Watchdog and Error 6.1. Introduction The relay contacts (normally open contact and normaly closed contact) of watchdog and error are available on plug X5 of the master control element. SICAM TM 1703 ACP CP-6014 X4 X11 X12 WD X5 X15 PUSH TO R EL E ASE X14 X1 6 X1 X13 X3 X6 X7 X8 X9 X10 SI M0 ER SI0 SI1 / L K / P K SI2 SI3 / L K / P K RY Master control element CP-6014 NC ER x TX LO C M-PRE/ 0 SI 0 M-PRE/ 1 SI 1 (ETO ) M-PRE/ 2 SI 2 (FB) M-PRE/ 3 SI 3 PUSH TO UNLOCK PWR VD C ER CO M CPY R ES X5 PU SH TO R EL EA SE Watchdog (WD) Error (ER) CP SICAM TM, Installation Edition , DC

69 7. Power Supply Content 7.1. Introduction Power Supply Master Control Element Power Supply Peripheral Element (Power Supply Module PS-663x) Power Supply Bus Interface Module (CM-0842) Fuse Protection Primary Mains Unit / Standard Type Siemens SICAM TM, Installation 69 DC , Edition

70 Power Supply 7.1. Introduction The following components must be supplied with 24-60VDC in a SICAM TM System: Master Control Element Peripheral Elements Optical Bus Interface Modules The supply can be carried out with single leads of the type H07V-K ( ) or a cable of the type LA-YY-0 (2x ) or H05VV-F3G ( ) respectively Power Supply Master Control Element SIM0 FB X3 X6 SICAM TM 1703 ACP CP-6014 X7 NC M-PRE/0 SI0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) M-PRE/3 SI3 TB PUSH TO RELEASE PUSH TO UNLOCK PWR 24-60VDC X8 X9 X10 X4 X11 X12 ERx RX TX LOC SI0 /PK WD /PK SI1 SI2 SI3 ER X5 COMCPY RY X15 ER RES PUSH TO RELEASE X14 X16 X1 /LK X13 /LK Master control element X Power supply X13 70 SICAM TM, Installation Edition , DC

71 Power Supply 7.3. Power Supply Peripheral Element (Power Supply Module PS-663x) To protect the power supply, the system has to provide sufficient protection against contact, fire and mechanical influences. The systen has to provide a circuit breaker for disconnection. The power supply modules require no maintenance. In case of damage, the device may not be opened. Siemens SICAM TM, Installation 71 DC , Edition

72 Power Supply 7.4. Power Supply Bus Interface Module (CM-0842) To supply the optical bus interface module with power, the cover panel must be opened. To do this the screws marked are to be removed. Then the cover panel can be removed and the power supply connected. SICAM 1703 SICAM 1703 SICAM Hint If several optical bus interface modules are used in one system, each must be supplied separately with power. This is also applicable if the modules are connected with each other by means of the interface connector. 72 SICAM TM, Installation Edition , DC

73 Power Supply 7.5. Fuse Protection For the fuse protection of the system, miniature circuit breakers 2-pole 2A characteristic C (standard type: Merlin Gerin C60H 6kA Item No. MER+C60H-C-2A) are recommended. The number of miniature circuit breakers required depends on the size of the system and individual requirements. One miniature circuit breaker is recommended for each peripheral element Primary Mains Unit / Standard Type See Appendix A, Recommended and tested purchased products Siemens SICAM TM, Installation 73 DC , Edition

74

75 8. Wiring Peripheral Elements Content 8.1. Introduction Master Control Element CP-6014 ó Peripheral Control Module PE Master Control Element CP-6014 ó Bus Interface Module CM-084x Bus Interface Module CM-0843 ó Peripheral Control Module PE Bus Interface Module CM-0842 ó Peripheral Control Module PE-6411, PE Bus Interface Module CM-0842 ó Bus Interface Module CM Siemens SICAM TM, Installation 75 DC , Edition

76 Wiring Peripheral Elements 8.1. Introduction The peripheral elements of a SICAM TM system communicate with the master control element via the serial Ax 1703 peripheral bus. The cabling of this Ax peripheral bus is dependent on the number of peripheral elements that are to be connected and whether the connection is to be carried out electrically or/and optically. The following chapter shows which cabling options are possible between master control element, bus interface module and peripheral element. Hint The electrical Ax bus cable (USB-cable) must be conducted outside the cable ducts provided for the peripheral cabling. 76 SICAM TM, Installation Edition , DC

77 TB FB RX SI0 SI1 Wiring Peripheral Elements 8.2. Master Control Element CP-6014 ó Peripheral Control Module PE-6410 SICAM TM 1703 ACP CP-6014 X4 /LK X13 X11 X12 /PK WD X5 X15 ER SI2 SIM0 X3 X6 X7 X8 X9 X10 PUSH TO RE LEA SE X14 X16 X1 SI3 /LK /PK RY Master control element CP-6014 Peripheral control module PE-6410 (electrical) X2 PU SH TO R ELEA SE NC M-PRE/0 SI0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) ERx TX M-PRE/3 SI3 PUSH TO UNLOCK PWR 24-60VDC LOC ER COM CPY RES Ax 1703 peripheral bus (electrical) USB cable up to 3m Designation USB-Cable for Peripheral Controller (1,5m) USB-Cable for Peripheral Controller (2,0m) USB-Cable for Peripheral Controller (3,0m) Item Number / MLFB TC MF13130GC010AA0 TC MF13130GC020AA0 TC MF13130GC030AA0 Siemens SICAM TM, Installation 77 DC , Edition

78 TB FB RX SI0 SI1 Wiring Peripheral Elements 8.3. Master Control Element CP-6014 ó Bus Interface Module CM-084x SICAM /LK /P K SICAM TM 1703 ACP CP-6014 X4 X11 X12 ER X5 COM CP Y X15 PUSH TO R ELE ASE X14 X16 X1 X13 ER X3 X6 X7 X8 X9 X10 WD SIM0 SI2 SI3 /LK /P K RY Master control element CP-6014 N C M -PRE/0 SI0 M -PRE/1 SI1 (ETO) M -PRE/2 SI2 (FB) ERx TX LOC M -PRE/3 SI3 PUSH TO U NLOCK PWR VDC RES Bus interface module CM-0842 (optical) X2 PUSH TO RE LEAS E Ax 1703 peripheral bus (electrical) Patch cable up to 3m Bus interface module CM-0843 (electrical) Designation Ax-Bus Patch Cable DSUB to RJ45 3m Cat5 Item Number/ MLFB T (1m) 6MF13040BC550AA0 T (2m) 6MF13040BC510AA0 T (3m) 6MF13040BC520AA0 78 SICAM TM, Installation Edition , DC

79 Wiring Peripheral Elements 8.4. Bus Interface Module CM-0843 ó Peripheral Control Module PE-6410 Bus interface module CM-0843 (electrical) Peripheral control module PE-6410 (electrical) Ax 1703 peripheral bus (electrical) USB cable up to 3m Designation USB-Cable for Peripheral Controller (1,5m) USB-Cable for Peripheral Controller (2,0m) USB-Cable for Peripheral Controller (3,0m) Item Number / MLFB TC MF13130GC010AA0 TC MF13130GC020AA0 TC MF13130GC030AA0 Siemens SICAM TM, Installation 79 DC , Edition

80 Wiring Peripheral Elements 8.5. Bus Interface Module CM-0842 ó Peripheral Control Module PE-6411, PE-6412 Bus interface module CM-0842 (optical) Peripheral control module PE-6411/12 (optical) SIC AM Ax 1703 peripheral bus (optical) Fiber optic cable up to 200m length Components for fiber optic cable ( m) Designation FO-INDOORCABLE-200-DUP FO-INDOORCABLE-200-DUP- BREAK FO-INDOORCABLE-200-DUP- BREAK-ROUND Item Number/ MLFB TF7-033 TF7-034 TF7-035 FO-OUTDOORCABLE-200-2FIB- ARM TF7-036 FO-CONNECTOR-ODLP-200 TF SICAM TM, Installation Edition , DC

81 Wiring Peripheral Elements 8.6. Bus Interface Module CM-0842 ó Bus Interface Module CM-0843 Ax 1703 peripheral bus (electrical) Patch cable up to 3m length SICAM Bus interface module CM-0842 (optical) Bus interface module CM-0843 (electrical) Designation Patch cable CAT5 (4x2) AWG26/7 Item Number/ MLFB T (1m) 6MF13040BC550AA0 T (2m) 6MF13040BC510AA0 T (3m) 6MF13040BC520AA0 Siemens SICAM TM, Installation 81 DC , Edition

82 Wiring Peripheral Elements 82 SICAM TM, Installation Edition , DC

83 9. Wiring Process Peripherals Content 9.1. Wiring Process Peripherals Peripheral Connector TE-6450 Wiring the Data Transmission Wiring of analog measured values Siemens SICAM TM, Installation 83 DC , Edition

84 Wiring Process Peripherals 9.1. Wiring Process Peripherals Cabinet-internal wiring is preferably carried out with plastic-insulated cables according to DIN VDE 298 T4 2/89. Types: H05V-K (0.5-1mm²), H07V-K ( ). The use of lead sleeves is recommended. The construction of the peripheral connectors is designed for direct peripheral wiring. That means, that the wiring can be carried out without the use of a routing terminal or other additional screw terminals. For the wiring, cable ducts are to be provided at both sides of the modules (refer to chapter 3.2.3, "Space Requirement"). Warning The activities described in this chapter presume that the grounding connection between SICAM TM and cabinet or rack has been properly carried out and that these are earthed. Warning For modules that operate with voltages >60V (e.g.: DO-6212, DI-6101) care must be taken that manipulation on the peripheral connectors may only be carried out in a de-energized state. The reason for this is that when withdrawing the upper peripheral connector under voltage, the external voltage can be conducted through the lower peripheral connector still connected. The pins of the upper peripheral connector now freely accessible will now conduct the external voltage. 84 SICAM TM, Installation Edition , DC

85 Wiring Process Peripherals 9.2. Peripheral Connector Terminal Type Designation Lead Exit Cross-section Screw terminal included in delivery side up to 2.5mm² Spring-loaded terminal Phönix Crimp terminal Crimp contact Phönix 1) 2) 3) up to 1.5mm² 1) FKC 2.5/10-ST-5.08 above up to 2.5mm² up to 1.5mm² 1) MSTBC 2.5/10-STZFD-5.08 MSTBC-MT above When using a jumper with 0.75mm² or a bridging cable fan (see: External wiring in 3-wire technique) Jumper with 0.75mm² Jumper with 1.00mm² External wiring in 3-wire technique 1.5mm² to 2.5mm² 1.5mm² 2) 1.0mm² 3) Designation Labeled screw terminal (1-10); without coding Labeled screw terminal (11-20); without coding Labeled screw terminal (21-30); without coding Labeled screw terminal (31-40); without coding Withdrawal aid for terminals Item Number / MLFB TC MF13130GC000AA0 Siemens SICAM TM, Installation 85 DC , Edition

86 Wiring Process Peripherals 9.3. TE-6450 Wiring the Data Transmission The data transmission between angle-/position sensor and TE-6450 takesplace via a 2x5x0.5mm twisted screened cable for each data interface. These cables must be conducted interruption-free. Intermediate- or disconnection terminals are not permitted. At the TM module side the cables are fastened and screened with screen clamp plates. The screen clamp plates (4 pieces are supplied with the module) are fixed in the grounded terminal points 14, 18, 24 and 28. At the angle-/position sensor side, the cable screens must also be grounded. 86 SICAM TM, Installation Edition , DC

87 Wiring Process Peripherals + - SPS0- RxD0+ RxD0- :1 SPS0+ :11 RxC0+ RxC0- SPS1+ :21 RxC2+ :31 RxD2+ RxC2- SPS1- RxD2- GND SPS0- TRANSDUCER + - SPS0+ RxD1+ RxC1+ RxD1- RxC1- RxD3+ GND SPS1+ RxC3+ RxC3- SPS1- RxD3- TRANSDUCER F GND GND F TRANSDUCER F F TRANSDUCER AUX V0- AUX V0+ Abb.2 :10 :20 :30 F... EMV-Filter :40 AUX V1- AUX V1+ Cable for the Supply For AUX V0+/- and AUX V1+/- one cable, at least 2 x 1mm 2, is used. Cable length between TE-6450 and Temposonics-Sensor Cable length (m) <20 <60 <180 Bit rate (kbit/s) Siemens SICAM TM, Installation 87 DC , Edition

88 Wiring Process Peripherals 9.4. Wiring of analog measured values During the wiring of measured values with single wires, the wires must be twisted. 88 SICAM TM, Installation Edition , DC

89 10. Shielding / Protective Earthing Content Shielding Protective Earthing / Grounding Siemens SICAM TM, Installation 89 DC , Edition

90 Shielding / Protective Earthing Shielding Basically the TM-modules are designed in such a way that no shielded cables are required. Normally, shielded cables are strain-relieved directly after the cabinet/rack entry and then grounded on a large-surface screening rail installed for this purpose. The terminal modules themselves provide no possibility of shield clamping. Exception For the module TE-6450 used for position acquisition, the screened cable must be conducted interruptionfree from the shaft encoder directly up to the module. There the screening is carried out with special clamps (screen clamp plate). (For details refer to section 9.3, "TE-6450 Wiring the Data Transmission"). 90 SICAM TM, Installation Edition , DC

91 Shielding / Protective Earthing Protective Earthing / Grounding When installing a SICAM TM system, attention is to be paid that the cabinet or rack used features a proper protective earthing / grounding. That means, that all electrical conducting parts must be connected large-surface and as short as possible with the cabinet spar. The cabinet spar itself must be connected with the existing grounding system. If these prerequisites are given, the grounding of the SICAM TM system takes place over a connection to the mounting sheet or to the TS35 rail. (grounding wire 2,5mm 2 ). A reliable connection is achieved by using screws with contact washers. Hint The TS35 rail of a complete equipped pripheral element (PS+PE+8 I/O Modules) must be bolted at least 4x on metallic background. This background must be at least 40 cm wide. A mounting plate is recommended. Siemens SICAM TM, Installation 91 DC , Edition

92

93 11. Labelling Content Introduction Labeling Master Control Element Labeling Peripheral Element Terminal Labeling Individual Terminal Point Labeling Terminal Coding Siemens SICAM TM, Installation 93 DC , Edition

94 Labelling Introduction This chapter shows how a SICAM TM system is to be labeled according to Standard. The following labels are provided: Region- and Component Number Plant- and Location Designation Equipment Identification (EI) PBA Number Terminal labeling Individual Terminal Point Labeling CP-6014 Plant, location (optional) Region number, component number, PBA number Equipment identification Plant, location (optional) 94 SICAM TM, Installation Edition , DC

95 Labelling Labeling Master Control Element The master control element is to be labeled with operational equipment designation, regionand component number Equipment Identification, Region Number, Component Number Designation Zack Strip ZB8/27 10 pcs Item Number PHO Siemens SICAM TM, Installation 95 DC , Edition

96 Labelling Plant- and Location Designation The parts used are identical with those for the region- and component number. 96 SICAM TM, Installation Edition , DC

97 Labelling Labeling Peripheral Element Region Number, Component Number, PBA Number The parts used are identical with those for the region- and component number. Siemens SICAM TM, Installation 97 DC , Edition

98 Labelling Plant- and Location Designation The plant- and location designation normally takes place on the cabinet in which the system is installed. If required, the plant- and location designation can however also take place on a further end bracket with terminal strip marker. This is fitted before the region- and component number. The parts used are identical with those for the region- and component number. 98 SICAM TM, Installation Edition , DC

99 Labelling Equipment Identification (EI) For the labeling of the modules with the equipment identification (EI) every module is fitted with a Phönix label plate type: ZB8/27. Regarded as standard labeling is: EI HW-Designation Use -Axx0 PS-66xx Power Supply -Axx1 PE-64xx Peripheral control module -Axx1.0 -Axx1.1 -Axx1.2 -Axx1.3 -Axx1.4 -Axx1.5 -Axx1.6 -Axx1.7 Periphery Periphery Periphery Periphery Periphery Periphery Periphery Periphery xx = (Nummer des Peripherieelements) Designation Zack strip ZB 8/27 10 pcs Item Number PHO Siemens SICAM TM, Installation 99 DC , Edition

100 Labelling Terminal Labeling The individual terminals are already labeled ex works. The numbering takes place consecutively from 1 20 (power supply module) or from 1-40 (on all I/O modules). 100 SICAM TM, Installation Edition , DC

101 Labelling Individual Terminal Point Labeling This method of labeling can take place optionally in addition to the terminal labeling. Thereby an adhesive plate is labeled individually, and then stuck to the slanted surface of the housing cover. Designation Label sheet BMKL 50x12 wh f. Laser print DIN A4 sheet with 63 white adhesive labels Item Number PHO Siemens SICAM TM, Installation 101 DC , Edition

102 Labelling Terminal Coding In order to prevent terminal strips of the lower level of a module (terminal labeling: 1-10 and 31-40) from being interchanged with those of the upper level of the same module (terminal labeling: and 21-30), terminals and male connectors are provided with a mechanical coding. A coding that prevents terminal strips of one module from being interchanged with those of another module can be realized with this method of coding, but is however not carried out at works. Designation PHOENIX CR-MSTB/ Coding Element 6 pces Item Number/ MLFB PHO Coding section for terminal strip TC MF13130GA550AA0 102 SICAM TM, Installation Edition , DC

103 12. Parameter Setting Preparation Content Introduction Physical connection between SICAM TOOLBOX II and SICAM TM Logical Connection between SICAM TOOLBOX II and SICAM TM Flash Card Siemens SICAM TM, Installation 103 DC , Ausgabedatum

104 Parameter Setting Preparation Introduction The SICAM TM system is parameterized with a PC on which the SICAM TOOLBOX II software is installed. For this, the SICAM TOOLBOX II and automation unit must be connected with each other and a Flash Card configured in the master control element: Physical connection between SICAM TOOLBOX II and SICAM TM Following connections are differentiated: direct local via toolbox cable serial via modems Ethernet (TCP/IP) Ethernet (TCP/IP) and Terminal Server (serial) 104 SICAM TM, Installation Ausgabedatum , DC

105 TB NC SI0 SI3 FB RX Parameter Setting Preparation Direct connection via toolbox cable SICAM TOOLBOX II and SICAM TM are connected direct via the toolbox cable. SICAM TM 1703 ACP CP-6014 SI0 X13 X4 X11 X12 WD SI1 ER X5 COMCP Y X15 PUSH TO R ELE ASE X14 X16 X1 ER SIM0 X3 X6 X7 X8 X9 X10 /LK /P K SI2 /LK /P K ERx TX LOC SI3 RY SICAM TOOLBOX II SICAM TM X2 M-PRE/0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) M-PRE/3 PUSH TO RE LEAS E PUSH TO U NLOCK PWR VDC RES CM-1820 TB Connection Cable CM-0820/ADAP TB Adapter Designation CM-1820 TB Cable Set Item Number/ MLFB BA MF10110BJ200AA0 CM-0820/ADAP TB Adapter GA MF11110AJ200AA0 Siemens SICAM TM, Installation 105 DC , Ausgabedatum

106 X2 TB NC FB RX SI0 Parameter Setting Preparation Serial via modem SICAM TOOLBOX II and SICAM TM are connected via 2 serial modems. SICAM TM 1703 ACP CP-6014 X1 X13 X4 X11 X12 WD X15 X14 X16 ER SIM0 X3 X6 X7 X8 X9 X10 X5 SI1 /LK /PK SI2 /LK /PK ERx TX LOC SI3 RY SICAM TOOLBOX II SICAM TM PUSH TO RELEASE M-PRE/0 SI0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) M-PRE/3 SI3 PUSH TO UNLOCK PWR 24-60VDC ER COMCPY RES PUSH TO RELEASE serial serial Modem line, PSTN, GSM,... Modem CM-1820 TB Connection Cable 106 SICAM TM, Installation Ausgabedatum , DC

107 TB NC FB RX SI 0 SI 1 /LK Parameter Setting Preparation Via Ethernet (TCP/IP) SICAM TOOLBOX II and SICAM TM are connected via Ethernet (TCP/IP). For this, the master control element must be fitted with additional SIM's. For details refer to section 4.2; Configuring Master Control Element with Serial Interface Modules (SIM). SICAM TOOLBOX II SICAM TM SICAM TM 1703 ACP CP-6014 X4 X11 X12 PUSH TO R ELE AS E X14 X16 X1 /P K X13 WD E R X5 COMCP Y X15 SI 2 ER SIM0 X3 X6 X7 X8 X9 X10 SI 3 /LK /P K RY X2 PUSH T O RE LEA SE M-PRE/0 SI0 M-PRE/1 SI1 (ETO) ERx TX LOC M-PRE/2 SI2 (FB) M-PRE/3 SI3 PUSH TO UNLOCK PWR 24-60VDC RES Communication Interface M-PRE/1 SI1 (Et0) X8 Ethernet (TCP/IP) Designation SM-2558 Ethernet-Interf. 1x100TX + 1 serial interface optional Item Number/ MLFB BC MF10130CF580AA0 Patch cable CAT5 (4x2) AWG26/7 (used for cabinet-internal wirings up to 10m) Patch cable CAT5 (4x2x0.5) AWG24 (used for cabinet-external wirings up to 100m) T (1m) 6MF13040BC550AA0 T (2m) 6MF13040BC510AA0 T (3m) 6MF13040BC520AA0 T (5m) 6MF13040BC530AA0 T (10m) 6MF13040BC540AA0 - Attention A first initialization of the automation unit is not possible with this method (IP-addresses, subnetmask). This is only possible via the TB-interface. Siemens SICAM TM, Installation 107 DC , Ausgabedatum

108 TB FB RX SI0 Parameter Setting Preparation Via Ethernet (TCP/IP) and Terminal Server (serial) SICAM TOOLBOX II and SICAM TM are connected via ethernet (TCP/IP) and terminal server (serial). X13 SICAM TM 1703 ACP CP-6014 X4 X11 X12 WD ER X5 COMCPY X15 PUSH TO RELEASE X14 X16 X1 ER SIM0 X3 X6 X7 X8 X9 X10 SI1 /LK /PK SI2 /LK /PK ERx TX LOC SI3 RY SICAM TOOLBOX II SICAM TM X2 PUSH TO RELEASE NC M-PRE/0 SI0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) M-PRE/3 SI3 PUSH TOUNLOCK PWR 24-60VDC RES Ethernet (TCP/IP) CM-0820/ADAP TB Adapter Terminal Server CM-1820 TB Anschlusskabel 108 SICAM TM, Installation Ausgabedatum , DC

109 TB TB Parameter Setting Preparation Logical Connection between SICAM TOOLBOX II and SICAM TM For engineering there must be a logical connection to those automation unit, which is subject of engineering. Following two cases are differentiated: Engineering of a local automation unit (that is that one, to which an physical connection exists) Attention A first initialization of the automation unit is only possible in this way. Engineering of a remote automation unit (automation unit, which can be accessed via a local automation unit; a continuous remote communication according to IEC or -104 is required) SICAM TM 1703 ACP CP-6014 X1 X13 FB SIM0 X3 X6 X7 X8 X9 X10 X4 X11 FB X12 WD X5 X15 ER X14 X16 RX RX SI 0 SI 0 SI 1 /LK / PK /LK / PK E Rx TX LOC SI 1 /LK /P K SI 2 SI 2 SI 3 SI 3 NC M-PRE/0 SI0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) M-PRE/3 SI3 /LK /P K PUS HTO UNLOCK PWR 24-60VDC E R COM CPY RY RY X2 SICAM PUSH T O RE LEA SE TM 1703 ACP CP-6014 RE S PUSH TO RELE AS E X3 X6 X7 X8 X9 X10 X4 X11 X12 WD X5 X1 5 ER RES PUSH TO RELE AS E X14 X1 6 X1 SIM0 SICAM TOOLBOX II local automation unit SICAM TM remote AU engineering local AU engineering ERx TX LOC E R COM CP Y physical connection PUSH TO RE LEA SE X2 NC M-PRE/0 SI0 M-PRE/1 SI1 (ETO) M-PRE/2 SI2 (FB) M-PRE/3 SI3 PUSH TO UNLOCK PWR 24-60VDC X13 SICAM TM remote AU engineering telecontrol network (IEC /104) remote automation unit Siemens SICAM TM, Installation 109 DC , Ausgabedatum

110 Parameter Setting Preparation Flash Card SICAM TM uses a flash card for the storage of parameters, user program, firmware codes for basis system elements and supplementary system elements and data of the decentralized archive (DEAR). This is located in the housing of the master control element. Attention The master control elements are supplied without flash card. Flash Card Designation Item Number / MLFB CC MF12131GA050AA0 110 SICAM TM, Installation Ausgabedatum , DC

111 Parameter Setting Preparation Inserting Flash Card Press through the recess in the housing on the locking panel situated below until the guide for the flash card is visible. Hold the locking panel in this position and guide the flash card in until it engages. Then the locking panel can be released again and the flash card is secured Locking Panel Guide for flash card Siemens SICAM TM, Installation 111 DC , Ausgabedatum

112 Parameter Setting Preparation Withdrawing Flash Card Press through the recess in the housing on the locking panel situated below until the flash card is visible. Hold the locking panel in this position and push the flash card slightly inwards. As a result it is disengaged and springs out of the guide a few millimeters. The flash card can now be removed and the locking panel released again SICAM TM, Installation Ausgabedatum , DC

113 A. Recommended and tested purchased products Content A.1. Modem A.2. DCF77 Accessories A.3. GPS Satellite Receiver / Accessories A.4. LAN Time Server A.5. Power Supplies Siemens SICAM TM, Installation 113 DC , Ausgabedatum

114 Recommended and tested purchased products A.1. Modem Standard modem for analog dial-up traffic Designation Item-Number / MLFB Eurocom 24 G MF11020BA140AA0 Westermo TD-36 AV ( VAC / VDC) Westermo TD-36 LV (DC) (10 30 VAC / VDC) Standard modem for ISDN dial-up traffic Westermo IDW-90 Designation Manufacturer Standard modem for GSM dial-up traffic Designation Siemens TC35 (dual band modem) Including DIN-rail installation kit and connection cable (1.5m) Item-Number G MF11020BA300AA1 Without antenna! GSM antenna for outside installation G MF11020BA310AA1 114 SICAM TM, Installation Ausgabedatum , DC

115 Recommended and tested purchased products A.2. DCF77 Accessories Designation KR-DCF/STAA DCF77 Stand. Outdoor Antenna. Manufacturer G MF11010CB070AA0 KR-DCF/V4 DCF77 Antenna Terminal Block G MF11010CB060AA0 Antenna cable (Coaxial cable RG58 C/U 50 Ohm) DCF/GPS-BS Lightning Protec. CN- UB/E-BB TF MF13140FA500AA0 BA MF10110AJ020AA0 GPS-antenna-connecting-kit TA MF13110AJ010AA0 Siemens SICAM TM, Installation 115 DC , Ausgabedatum

116 Recommended and tested purchased products A.3. GPS Satellite Receiver / Accessories Designation Meinberg GPS164DHS Receiver for TS35 Manufacturer GPS167-ANT/CON GPS-Antenna- /Converter. GPS-AV4 Antenna Terminal Block Antenna cable (Coaxial cable RG58 C/U 50 Ohm) DCF/GPS-BS Lightning Protec. CN- UB/E-BB TF MF13140FA500AA0 BA MF10110AJ020AA0 GPS-antenna-connecting-kit TA MF13110AJ010AA0 116 SICAM TM, Installation Ausgabedatum , DC

117 Recommended and tested purchased products A.4. LAN Time Server Designation Meinberg NTP Server + Antenna + Cable Manufacturer A.5. Power Supplies Designation Power Supply 5V/2A SYKO EWS 01 U VAC or VDC Manufacturer Power S. 115/230VAC, VDC- 24VDC-50W Siemens SICAM TM, Installation 117 DC , Ausgabedatum

118 Recommended and tested purchased products 118 SICAM TM, Installation Ausgabedatum , DC

119 B. Licensing Agreement B.1. Open Source Software used in SICAM TM This product contains, among other things, Open Source Software developed by third parties. The Open Source Software used in this product and the license agreements concerning this software can be found in the Readme_OSS. These Open Source Software files are protected by copyright. Your compliance with those license conditions will entitle you to use the Open Source Software as foreseen in the relevant license. In the event of conflicts between Siemens license conditions and the Open Source Software license conditions, the Open Source Software conditions shall prevail with respect to the Open Source Software portions of the software. The Open Source Software is licensed royalty-free. Insofar as the applicable Open Source Software License Conditions provide for it you can order the source code of the Open Source Software from your Siemens sales contact - against payment of the shipping and handling charges - for a period of at least 3 years since purchase of the Product. We are liable for this Product including the Open Source Software contained in it pursuant to the license conditions applicable to the Product. Any liability for the Open Source Software beyond the program flow intended for this Product is explicitly excluded. Furthermore any liability for defects resulting from modifications to the Open Source Software by you or third parties is excluded. We do not provide any technical support for this Product if it has been modified. The Open Source Software used in this product and the license agreements concerning this software can be found on the SICAM RTUs SD card in the file ReadmOSS.htm. To readout this file, you need an application that you can download from the Internet. You can find details for the download and the use of the application in the following chapter. B.1.1. Readout of ReadmOSS.htm Note You need a SD card reader and a web browser to read the htm-file. The application for the readout of the ReadmOSS-data from the SD-card can be downloaded from following web page: Siemens SICAM TM, Installation 119 DC , Edition

120 Licensing Agreement Click DOWNLOAD POOL in the menu bar and select on tab PRODUCTS & SYSTEMS following options: Product Family:SICAM RTUs Product / Version:General Infomation Click SEARCH Click on SICAM RTUS OSS EXTRACTOR in the result list to start the download. When the download is finished you will get the file SICAMOSS.zip. Unzip this file and save the therein contained file (SICAMOSS.exe) in the root path of the SDcard from which you want to readout the license agreement. 120 SICAM TM, Installation Edition , DC

121 Licensing Agreement Start now SICAMOSS.exe. During the readout process you can see a DOS-window. If the line note: All files processed is displayed you can close the DOS-window by pressing any key. Now you can find on the SD-card the folder OSS with several subfolders. One single folder for each firmware which uses open source components. Within these subfolders are again folders for each used firmware revision. These folders contain the corresponding license data. Path for ReadmeOSS: SD-Card:\OSS\<Firmwarename>\<Firmwarenumber>\<Revision>\ReadmOSS.htm. E.g.: SD-Card:\OSS\ETA4\02.01\ReadmOSS.htm Example of a ReadmOSS.htm: Siemens SICAM TM, Installation 121 DC , Edition