ACP 1703 Platforms. Automation Units and Automation Networks DC Preface, Table of Contents. Configuration of Automation Units 1

Transcription

1 ACP 703 Platforms Automation Units and Automation Networks Preface, Table of Contents Configuration of Automation Units Configuration of Automation Networks Redundancy 3 Transmission of Disturbance Records 4 Reception of Time Signals 5 Appendix A Literature DC0-0-.0

2 Hint Please observe Notes and Warnings for your own safety in the Preface. Disclaimer of Liability Although we have carefully checked the contents of this publication for conformity with the hardware and software described, we cannot guarantee complete conformity since errors cannot be excluded. The information provided in this manual is checked at regular intervals and any corrections that might become necessary are included in the next releases. Any suggestions for improvement are welcome. Copyright Copyright Siemens AG 0 The reproduction, transmission or use of this document or its contents is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Subject to change without prior notice. Document Label: SIC703-HBACPCONFIG-ENG_V.0 Release date.07. Siemens Aktiengesellschaft Order no.: DC0-0-.0

3 Preface This document is applicable to the following product(s): AK 703 ACP BC 703 ACP TM 703 ACP TM 703 emic TM 703 mic Purpose This manual describes the recommended configurations for the ACP 703 system. Representation of configurations Information about used types and lengths of cables Listing of used modules and cables with their item numbers additional important hints Target Group This handbook is intended for persons who are entrusted with the design of ACP 703 systems. ACP 703 Platforms, Configuration AU Networks 3 DC0-0-.0, Edition 07.0

4 Notes on Safety This manual does not constitute a complete catalog of all safety measures required for operating the equipment (module, device) in question because special operating conditions might require additional measures. However, it does contain notes that must be adhered to for your own personal safety and to avoid damage to property. These notes are highlighted with a warning triangle and different keywords indicating different degrees of danger. Danger means that death, serious bodily injury or considerable property damage will occur, if the appropriate precautionary measures are not carried out. Warning means that death, serious bodily injury or considerable property damage can occur, if the appropriate precautionary measures are not carried out. Caution means that minor bodily injury or property damage could occur, if the appropriate precautionary measures are not carried out. Hint Please observe Notes and Warnings for your own safety in the Preface. Qualified Personnel Commissioning and operation of the equipment (module, device) described in this manual must be performed by qualified personnel only. As used in the safety notes contained in this manual, qualified personnel are those persons who are authorized to commission, release, ground, and tag devices, systems, and electrical circuits in accordance with safety standards. Use as Prescribed The equipment (device, module) must not be used for any other purposes than those described in the Catalog and the Technical Description. If it is used together with third-party devices and components, these must be recommended or approved by Siemens. Correct and safe operation of the product requires adequate transportation, storage, installation, and mounting as well as appropriate use and maintenance. During operation of electrical equipment, it is unavoidable that certain parts of this equipment will carry dangerous voltages. Severe injury or damage to property can occur if the appropriate measures are not taken: Before making any connections at all, ground the equipment at the PE terminal. Hazardous voltages can be present on all switching components connected to the power supply. Even after the supply voltage has been disconnected, hazardous voltages can still be present in the equipment (capacitor storage). Equipment with current transformer circuits must not be operated while open. The limit values indicated in the manual or the operating instructions must not be exceeded; that also applies to testing and commissioning. 4 ACP 703 Platforms, Configuration AU Networks DC0-0-.0, Edition 07.0

5 Table of Contents Configuration of Automation Units...7. Base Unit AK 703 ACP with Peripheral Elements AK 703 ACP, local PE AK 703 ACP AK 703 ACP PE, electrical AK 703 ACP TM 703 ACP PE, optical AK 703 ACP TM 703 ACP PE, optical, multi-hierarchical AK 703 ACP TM 703 ACP PE, electrical and optical AK 703 ACP AM 703 PE and BC 703, optical...6. Base Unit TM 703 ACP with Peripheral Elements TM 703 ACP TM 703 ACP PE, electrical TM 703 ACP TM 703 ACP PE, electrical and optical Base Unit BC 703 ACP/M with Peripheral Elements BC 703 ACP/M TM 703 ACP PE, optical... Configuration of Automation Networks...3. Serial Communication Point-to-point-traffic, IEC , electrical Point-to-point-traffic, IEC , optical Multi-point Traffic, IEC or -03, electrical Multi-point Traffic, IEC or 03, optical, Star Multi-point Traffic, IEC or 03, optical, Ring Multi-point Traffic, IEC or 03, optical, RingStar Multi-point Traffic, IEC or 03, optical, Tree Multi-point Traffic, IEC , optical, s Methods for Coupling of (non-siemens) Protective Devices in Ring Configurations Dial-up Traffic analog/gsm, IEC Dial-up Traffic ISDN, IEC Dial-up Traffic analog/gsm/isdn, IEC SIEMENS Fieldbus, IEC , electrical SIEMENS Fieldbus, IEC , optical, Star SIEMENS Fieldbus, IEC , optical, Ring SIEMENS Fieldbus, IEC , optical, Tree LAN Communication LAN Communication electrical LAN Communication optical Fieldbus/Profibus Communication Fieldbus/Profibus Communication: Master AK 703 ACP Fieldbus/Profibus Communication: Master TM 703 ACP...75 ACP 703 Platforms, Configuration AU Networks 5 DC0-0-.0, Edition 07.0

6 Table of Contents 3 Redundancy Redundant Basic System Elements AK 703 ACP AK 703 ACP PE, electrical, redundant BSE AK 703 ACP TM 703 ACP PE, electrical, redundant BSE AK 703 ACP TM 703 ACP PE, electrical and optical, redundant BSE AK 703 ACP TM 703 ACP PE, optical, redundant BSEredundant Ax- PE-Bus Data Transfer between redundant BSE-Pairs Redundant Automation Units Redundant AUs, Voting by SCA-RS, Distance up to 5 m Redundant AUs, Voting by SCA-RS, Distance up to 00 m Redundant AUs, Voting by SCA-RS, Distance higher than 00 m Wiring of the Modular Coupling RJ-45 9-pol D-SUB Redundant Automation Units in star-shaped Configurations Redundant Automation Units in ring-shaped Configurations Transmission of Disturbance Records General Reception of Time Signals Time Master 4 Options Methods for Time Synchronization Time Synchronization by Serial Time Signal Time Synchronization by Minute Pulse Time Synchronization by Remote Synchronization... A Appendix... 3 A. Electrical Connection, Cable longer than 0 m... 4 A. Signal Propagation Delays ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

7 Configuration of Automation Units Content. Base Unit AK 703 ACP with Peripheral Elements...8. Base Unit TM 703 ACP with Peripheral Elements Base Unit BC 703 ACP/M with Peripheral Elements... ACP 703 Platforms, Configuration AU Networks 7 DC0-0-.0, Edition 07.0

8 ESD EAR TH FA CILITY PS-560 Configuration of Automation Units. Base Unit AK 703 ACP with Peripheral Elements.. AK 703 ACP, local PE Local peripheral elements in an AK 703 ACP base unit base unit AK 703 ACP peripheral elements CP-00 To one basic system element CP-00/CPC5 or CP-07/PCCX5 one bus line with max. 6 peripheral elements can be connected. The Ax-PE bus can be driven by one of the CPUs (C0-CPU to C6-CPU). Default: C0-CPU Necessary modules and cables Base unit AK 703 ACP Designation CP-00 Master control element CP-00/CPC5 CP-07 Processing and element CP-07/PCCX5 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-07 / 6MF030CA70AA0 8 ACP 703 Platforms, Configuration AU Networks Ausgabedatum 07.0, DC0-0-.0

9 ES D EA RTH FA CILITY ES D EA RTH FA CILITY PS-560 PS-560 Configuration of Automation Units.. AK 703 ACP AK 703 ACP PE, electrical Base unit AK 703 ACP to peripheral elements AK 703 ACP, electrically connected base unit AK 703 ACP Ax 703 peripheral bus (electrical) 6 Mbps patch-cable, length up to 3 m peripheral elements AK 703 ACP (max. 6 PE) CP-07 CP-00 rear view CM-833 Line To one basic system element CP-00/CPC5 or CP-07/PCCX5 one bus line with max. 6 peripheral elements can be connected. Depending on the slot of the basic system element the socket connector for the electrical Ax 703 peripheral bus has to be selected. (for example: slot C socket connector AXPE-C) Necessary modules and cables Base unit AK 703 ACP Cable Peripheral elements AK 703 ACP Designation CP-00 Master control element CP-00/CPC5 CP-07 Processing and element CP-07/PCCX5 Patch cable CAT5 (4x) AWG6/7 CM-833 AK 703 ACP board rack extension Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-07 / 6MF030CA70AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 GC-833 / 6MF30CJ330AA0 ACP 703 Platforms, Configuration AU Networks 9 DC0-0-.0, Ausgabedatum 07.0

10 ESD EAR TH FA CILITY PS Configuration of Automation Units..3 AK 703 ACP TM 703 ACP PE, optical Base unit AK 703 ACP to peripheral elements TM 703 ACP, optically connected base unit AK 703 ACP Ax 703 Peripheral bus (electrical) 6 Mbps patch-cable, length up to 3 m Bus Interface Modules CM-084 (max. 4) Settings on the configuration switch S ON S OFF CP-07 CP-00 Ax 703 peripheral bus (optical) 6 Mbps FO, length up to 00 m PS-663x PE-64 I/O modules (max. 8) peripheral elements TM 703 ACP (max. 6 PE) peripheral element To one basic system element CP-00/CPC5 or CP-07/PCCX5 one bus line with max. 6 peripheral elements can be connected. Depending on the slot of the basic system element the socket connector for the electrical Ax 703 peripheral bus has to be selected. (for example: slot C socket connector AXPE-C) In configurations with optical remoted TM 703 ACP PEs 000µm-fibre cables cannot be used! Each bus interface module CM-084 has to be supplied separately. (8 VDC VDC) Configuration switch CM F/F...ON...6 MBit... LINE...OFF...PE(O) 3... AS...OFF AS...OFF AS0...OFF RED...OFF...CM LAD...OFF...inactive 8... LINE...OFF...PE 0 ACP 703 Platforms, Configuration AU Networks Ausgabedatum 07.0, DC0-0-.0

11 Configuration of Automation Units Necessary modules and cables Base unit AK 703 ACP Designation CP-00 Master control element CP-00/CPC5 CP-07 Processing and element CP-07/PCCX5 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-07/ 6MF030CA70AA0 Cable Patch cable CAT5 (4x) AWG6/7 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Bus interface modules Cable Peripheral elements TM 703 ACP CM-084 Ax 703-bus interface 4x FO FO-INDOORCABLE-00-DUP-BREAK-ROUND FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-OUTDOORCABLE-00-FIB-ARM FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-PIPE SPLITT Y-LR ( pcs. per connection) (only for outdoorcabletf7-036) PE-64 peripheral coupling Ax-bus x optical GA0-84 / 6MF0AJ40AA0 TF7-035 TF7-05 TF7-036 TF7-05 TF7-066 GC6-4 / 6MF30GE0AA0 ACP 703 Platforms, Configuration AU Networks DC0-0-.0, Ausgabedatum 07.0

12 ESD EA RTH FACILITY 0 0 PS Configuration of Automation Units..4 AK 703 ACP TM 703 ACP PE, optical, multi-hierarchical Base unit AK 703 ACP to peripheral elements TM 703 ACP, optically, multi-hierarchically connected base unit AK 703 ACP Ax 703 Peripheral bus (electrical) 6 Mbps patch-cable, length up to 3 m Bus Interface Modules CM-084 (max. 4) Settings A on the configuration switch S ON S OFF CP-07 CP-00 Ax 703 peripheral bus (optical) 6 Mbps FO, length up to 00 m Bus Interface Modules CM-084 (max. 4) ON S OFF Settings A on the configuration switch S ON S OFF Settings B on the configuration switch S PS-663x PE-64 I/O modules (max. 8) peripheral elements TM 703 ACP (max. 6 PE) peripheral element Ax 703 peripheral bus (optical) 6 Mbps FO, length up to 00 m ACP 703 Platforms, Configuration AU Networks Ausgabedatum 07.0, DC0-0-.0

13 Configuration of Automation Units To one basic system element CP-00/CPC5 or CP-07/PCCX5 one bus line with max. 6 peripheral elements can be connected. Depending on the slot of the basic system element the socket connector for the electrical Ax 703 peripheral bus has to be selected. (for example: slot C socket connector AXPE-C) In configurations with optical remoted TM 703 ACP PEs 000µm-fibre cables cannot be used! Each bus interface module CM-084 has to be supplied separately. (8 VDC VDC) Settings A on the Configuration switch CM F/F... ON... 6 MBit...LINE... OFF... PE(O) 3...AS... OFF AS... OFF AS0... OFF RED... OFF... CM LAD... OFF... inactive 8...LINE... OFF... PE Settings B on the Configuration switch CM F/F... ON... 6 MBit...LINE... ON... BSE(I) 3...AS... OFF AS... OFF AS0... OFF RED... OFF... CM LAD... OFF... inactive 8...LINE... OFF... PE Necessary modules and cables Base unit AK 703 ACP Designation CP-00 Master control element CP-00/CPC5 CP-07 Processing and element CP-07/PCCX5 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-07 / 6MF030CA70AA0 Cable Patch cable CAT5 (4x) AWG6/7 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Bus interface modules Cable Peripheral elements TM 703 ACP CM-084 Ax 703-bus interface 4x FO FO-INDOORCABLE-00-DUP-BREAK-ROUND FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-OUTDOORCABLE-00-FIB-ARM FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-PIPE SPLITT Y-LR ( pcs. per connection) (only for outdoorcabletf7-036) PE-64 peripheral coupling Ax-bus x optical GA0-84 / 6MF0AJ40AA0 TF7-035 TF7-05 TF7-036 TF7-05 TF7-066 GC6-4 / 6MF30GE0AA0 ACP 703 Platforms, Configuration AU Networks 3 DC0-0-.0, Ausgabedatum 07.0

14 ES D EA RTH FA CILITY PS Configuration of Automation Units..5 AK 703 ACP TM 703 ACP PE, electrical and optical Base unit AK 703 ACP to peripheral elements TM 703 ACP, electrically and optically connected base unit AK 703 ACP Ax 703 peripheral bus (electrical) 6 Mbps patch-cable, length up to 3 m Settings on the configuration switch S bus interface modules CM-084 ON S OFF bus interface modules CM-0843 CP-07 CP-00 PS-663x PE-640 Ax 703 peripheral bus (electrical) 6 Mbps USB-cable, length up to 3 m I/O modules (max. 8) Ax 703 peripheral bus (optical) 6 Mbps FO, length up to 00 m peripheral element PS-663x PE-64 I/O modules (max. 8) peripheral elements TM 703 ACP (max. 6 PE) 3 peripheral element ACP 703 Platforms, Configuration AU Networks Ausgabedatum 07.0, DC0-0-.0

15 Configuration of Automation Units To one basic system element CP-00/CPC5 or CP-07/PCCX5 one bus line with max. 6 peripheral elements can be connected. Depending on the slot of the basic system element the socket connector for the electrical Ax 703 peripheral bus has to be selected. (for example: slot C socket connector AXPE-C) In configurations with optical remoted TM 703 ACP PEs 000µm-fibre cables cannot be used! The bus interface modules CM-0843 are supplied by the power supplies PS-663x. The power consumption of the CM-0843 (see technical data in data sheet) has to be considered on the PS-663x. Each bus interface module CM-084 has to be supplied separately. (8 VDC VDC) Configuration switch CM F/F... ON... 6 MBit...LINE... OFF... PE(O) 3...AS... OFF AS... OFF AS0... OFF RED... OFF... CM LAD... OFF... inactive 8...LINE... ON... : Necessary modules and cables Base unit AK 703 ACP Designation CP-00 Master control element CP-00/CPC5 CP-07 Processing and element CP-07/PCCX5 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-07 / 6MF030CA70AA0 Cable Patch cable CAT5 (4x) AWG6/7 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Bus interface modules CM-0843 Ax 703-bus interface electrical CM-084 Ax 703-bus interface 4x FO GA0-843 / 6MF0AJ430AA0 GA0-84 / 6MF0AJ40AA0 Cable USB-cable TC6-0 (.5m)) / 6MF330GC00AA0 TC6-0 (m) / 6MF330GC00AA0 TC6-03 (3m) / 6MF330GC030AA0 Cable 3 Peripheral elements TM 703 ACP FO-INDOORCABLE-00-DUP-BREAK-ROUND FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-OUTDOORCABLE-00-FIB-ARM FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-PIPE SPLITT Y-LR ( pcs. per connection) (only for outdoorcabletf7-036) PE-640 peripheral coupling Ax-bus electrical PE-64 peripheral coupling Ax-bus x optical TF7-035 TF7-05 TF7-036 TF7-05 TF7-066 GC6-40 / 6MF30GE00AA0 GC6-4 / 6MF30GE0AA0 ACP 703 Platforms, Configuration AU Networks 5 DC0-0-.0, Ausgabedatum 07.0

16 ESD EAR TH FA CILITY PS Configuration of Automation Units..6 AK 703 ACP AM 703 PE and BC 703, optical Base unit AK 703 ACP to peripheral elements AM 703 and to BC 703, optically connected base unit AK 703 ACP Ax 703 Peripheral bus (electrical) 4 Mbps patch-cable, length up to 3 m bus interface modules CM-084 (max. 4) Settings on the configuration switch S ON S OFF CP-07 CP-00 peripheral elements AM 703 Ax 703 peripheral bus (optical) 4 Mbps FO, length up to 00 m BC 703 Model : PE Model : PE peripheral elements CM-83/CM-83 PS-6xx 6 ACP 703 Platforms, Configuration AU Networks Ausgabedatum 07.0, DC0-0-.0

17 Configuration of Automation Units To one basic system element CP-00/CPC5 or CP-07/PCCX5 one bus line with max. 6 peripheral elements can be connected. Depending on the slot of the basic system element the socket connector for the electrical Ax 703 peripheral bus has to be selected. (for example: slot C socket connector AXPE-C) The data rate for connections with AM 703 and BC 703 is 4 MBps. The combination of different data rates on one bus line is not possible Each bus interface module CM-084 has to be supplied separately. (8 VDC VDC) The BC 703 model includes PE, the model includes PE. Model 3 cannot be connected via the Ax 703 peripheral bus. Configuration switch CM F/F... OFF... 4 MBit...LINE... OFF... PE(O) 3...AS... OFF AS... OFF AS0... OFF RED... OFF... CM LAD... OFF... inactive 8...LINE... OFF... PE Necessary modules and cables Base unit AK 703 ACP Designation CP-00 Master control element CP-00/CPC5 CP-07 Processing and element CP-07/PCCX5 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-07 / 6MF030CA70AA0 Cable Patch cable CAT5 (4x) AWG6/7 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Bus interface modules Cable Peripheral elements AM 703 CM-084 Ax 703-Bus interface 4x FO FO-INDOORCABLE-00-DUP-BREAK-ROUND FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-OUTDOORCABLE-00-FIB-ARM FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-PIPE SPLITT Y-LR ( pcs. per connection) (only for outdoorcabletf7-036) CM-80x board rack (for 3, 5, 0, 4, 0 slots) CM-83 bus-interface-slave x FO CM-83 bus-interface-slave x FO (0/0VDC) GA0-84 / 6MF0AJ40AA0 TF7-035 TF7-05 TF7-036 TF7-05 TF7-066 GA-80x GA-83 / 6MF0BJ30AA0 GA-83 / 6MF0BJ30AA0 BC 703 CM-5800 BC 703 model CM-580 BC 703 model GA5-800 / 6MF0FJ000AA0 GA5-80 / 6MF0FJ00AA0 ACP 703 Platforms, Configuration AU Networks 7 DC0-0-.0, Ausgabedatum 07.0

18 PU SH TO R ELEAS E X X3 TB X6 X7 NC Configuration of Automation Units. Base Unit TM 703 ACP with Peripheral Elements.. TM 703 ACP TM 703 ACP PE, electrical Base unit TM 703 ACP to peripheral elements TM 703 ACP, electrically connected base unit TM 703 ACP Ax 703 peripheral bus (electrical) 6 Mbps USB-cable, length up to 3 m 0-0 SIM0 X4 X X X X4 X6 X8 X9 X0 FB LOC SI /LK SI /LK RES /PK WD /PK X5 X X3 M-PRE/0 M-PRE/ SI (ETO) x RX TX PWR PUSH TO R ELEA SE M-PRE/ SI (FB) M-PRE/3 PUSH TO U NLOCK 4-60 VDC COMCPY Communication with other automation units Ax 703 peripheral bus (electrical) 4 Mbps patch-cable, length up to 3 m bus interface modules CM-0843 (max. 4) peripheral elements TM 703 ACP (max. 6 PE) Ax 703 peripheral bus (electrical) 6 Mbps USB-cable, length up to 3 m peripheral element PE-640 PS-663x I/O modules (max. 8) To one master control element one bus line with max. 6 peripheral elements can be connected. The bus interface modules CM-0843 are supplied by the power supplies PS-663x. The power consumption of the CM-0843 (see technical data in data sheet) has to be considered on the PS-663x. 8 ACP 703 Platforms, Configuration AU Networks Ausgabedatum 07.0, DC0-0-.0

19 Configuration of Automation Units Necessary modules and cables Base unit TM 703 ACP Designation CP-604 Master control element CP-604/CPCX65 Item Number / MLFB GC6-04 / 6MF30GA40AA0 Cable Patch cable CAT5 (4x) AWG6/7 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Bus Interface Module CM-0843 Ax 703-bus interface electrical GA0-843 / 6MF0AJ430AA0 Cable USB-cable TC6-0 (.5m) / 6MF330GC00AA0 TC6-0 (m) / 6MF330GC00AA0 TC6-03 (3m) / 6MF330GC030AA0 Peripheral elements TM 703 ACP PE-640 peripheral coupling Ax-bus electrical GC6-40 / 6MF30GE00AA0 ACP 703 Platforms, Configuration AU Networks 9 DC0-0-.0, Ausgabedatum 07.0

20 PUS H TO RELE ASE X X3 TB X6 X7 NC SIM0 X8 X9 X0 X4 FB X X LOC SI 0 SI /LK /PK SI WD SI 3 RE S /LK /PK X5 X PWR X PUSH TO RE LE ASE X3 0 0 Configuration of Automation Units.. TM 703 ACP TM 703 ACP PE, electrical and optical Base unit TM 703 ACP to peripheral elements TM 703 ACP, electrically and optically connected base unit TM 703 ACP Ax 703 peripheral bus (electrical) 6 Mbps patch-cable, length up to 3 m bus interface modules CM x RX TX COM CPY X4 X6 M-PR E/0 M-PR E/ SI (ETO) M-PR E/ SI (FB) M-PR E/3 PUSH TO UNLOCK 4-6 0VDC Communication with other automation units ON S OFF bus interface modules CM-0843 Ax 703 peripheral bus (optical) 6 Mbps FO, length up to 00 m PS-663x PE-640 Ax 703 peripheral bus (electrical) 6 Mbps USB-cable, length up to 3 m I/O modules (max. 8) peripheral element PS-663x PE-64 I/O modules (max. 8) peripheral elements TM 703 ACP (max. 6 PE) 3 peripheral elements ACP 703 Platforms, Configuration AU Networks Ausgabedatum 07.0, DC0-0-.0

21 Configuration of Automation Units To one master control element one bus line with max. 6 peripheral elements can be connected. Each bus interface module CM-084 has to be supplied separately. (8 VDC VDC) The bus interface modules CM-0843 are supplied by the power supplies PS-663x. The power consumption of the CM-0843 (see technical data in data sheet) has to be considered on the PS-663x. In configurations with optical remoted TM 703 ACP PEs 000µm-fibre cables cannot be used! Configuration switch CM F/F... ON... 6 MBit...LINE... OFF... PE(O) 3...AS... OFF AS... OFF AS0... OFF RED... OFF... CM LAD... OFF... inactive 8...LINE... ON... : Necessary modules and cables Base unit TM 703 ACP Designation CP-604 Master control element CP-604/CPCX65 Item Number / MLFB GC6-04 / 6MF30GA40AA0 Cable Patch cable CAT5 (4x) AWG6/7 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Bus interface modules CM-0843 Ax 703-bus interface electrical CM-084 Ax 703-bus interface 4x FO GA0-843 / 6MF0AJ430AA0 GA0-84 / 6MF0AJ40AA0 Cable USB-cable TC6-0 (.5m) / 6MF330GC00AA0 TC6-0 (m) / 6MF330GC00AA0 TC6-03 (3m) / 6MF330GC030AA0 Cable 3 Peripheral elements TM 703 ACP FO-INDOORCABLE-00-DUP-BREAK-ROUND FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-OUTDOORCABLE-00-FIB-ARM FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-PIPE SPLITT Y-LR ( pcs. per connection) (only for outdoorcabletf7-036) PE-640 peripheral coupling Ax-bus electrical PE-64 peripheral coupling Ax-bus x optical TF7-035 TF7-05 TF7-036 TF7-05 TF7-066 GC6-40 / 6MF30GE00AA0 GC6-4 / 6MF30GE0AA0 ACP 703 Platforms, Configuration AU Networks DC0-0-.0, Ausgabedatum 07.0

22 0, F 0 F /- Configuration of Automation Units.3 Base Unit BC 703 ACP/M with Peripheral Elements.3. BC 703 ACP/M TM 703 ACP PE, optical base unit BC 703 ACP/M Ax 703 peripheral bus (optical) 6 Mbps FO, length up to 00 m PS-663x PE-64 I/O modules (max. 8) peripheral elements TM 703 ACP peripheral element To one master control element CP-504/CPCX55 one bus line with max. 5 peripheral elements can be connected. The configuration shown can only be made with BC 703 ACP/M. BC 703 ACP/C is not suitable for it. In configurations with optical remoted TM 703 ACP PEs 000µm-fibre cables cannot be used! The optical bus interface for the connection of external PE to the Ax 703 PE-bus (CM- 5807) is ordered over the configurator with the BC 703 ACP/M. (slot position : N CP-504/CPCX55, 03-, with ext. Ax PE-bus) Necessary modules and cables Base unit BC 703 ACP/M Cable Peripheral elements TM 703 ACP Designation BC 703 ACP/M Master control element CP-504/CPCX55 is ordered via the configurator FO-INDOORCABLE-00-DUP-BREAK-ROUND FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-OUTDOORCABLE-00-FIB-ARM FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-PIPE SPLITT Y-LR ( pcs. per connection) (only for outdoorcabletf7-036) PE-64 peripheral coupling Ax-bus x optical DC5-005 TF7-035 TF7-05 TF7-036 TF7-05 TF7-066 Item Number / MLFB GC6-4 / 6MF30GE0AA0 ACP 703 Platforms, Configuration AU Networks Ausgabedatum 07.0, DC0-0-.0

23 Configuration of Automation Networks Content. Serial Communication...4. LAN Communication Fieldbus/Profibus Communication...74 ACP 703 Platforms, Configuration AU Networks 3 DC0-0-.0, Edition 07.0

24 ESD EARTH FACILITY PS-560 PUSHTO RE LE AS E X X3 TB X6 NC M-PRE/0 X7 SIM0 M-PRE/ SI ( ETO) X8 X9 M-PRE/ SI ( FB) X0 M-PRE/3 X4 FB PUSHTO RE LE AS E X X X3 TB X X6 NC M-PRE/0 X7 SIM0 M-PRE/ SI ( ETO) X8 LO C ESD EARTH FACILITY X9 M-PRE/ SI ( FB) X0 M-PRE/3 X4 FB X X LO C WD /PK X5 SI /LK SI /LK RES /PK X PWR X PU SH TO RE LEA S E X3 PS-560 ESD EAR TH FAC ILITY PS-560 Configuration of Automation Networks. Serial Communication.. Point-to-point-traffic, IEC , electrical IEC Master AK 703 ACP or TM 703 ACP Cable Patchcable 0-0 PUSH TO UNL OCK x RX TX COMCPY 4-60 VDC X4 X6 distance > 0 m: with plenum cable via wall socket or patch panel Modem - master Modem Modem Modem Transmission network Modem - slave Modem Modem Modem Modem Cable 3 Modemcable x RX TX X4 X6 SI /LK X /PK WD /LK /PK X5 X5 X3 SI RES PWR PU SH TO RE LEA S E COMCPY Modem 3 s TM 703 ACP PUSH TO UNL OCK 4-60 VDC TM 703 emic TM 703 mic AK 703 ACP AK 703 The length of the electrical cable between AK 703 ACP respectively AK 703 and the modem is: max. 5m when the modem is supplied externally (depending on baudrate) max. 3m when modem is supplied internally Hints for establishing an electrical connection of more than 0 m length you can find in the appendix. For modem master and modem slave the same modem type has to be used. Details for supply of the modems you can find in the installation manuals AK 703 ACP, TM 703 ACP, TM 703 emic, TM 703 mic 4 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

25 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP Master TM 703 ACP Cable Modem Master/ AK 703 ACP Cable TM 703 ACP Cable 3 TM 703 emic TM 703 mic AK 703 Designation CP-00 systemfunction, processing and CM-837 connect. comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/BPPA0 SM-556 SM-055/BPPA0 CM-860 patch plug standard V8,ET,TR CP-604 master control element SM-55/BPPA0 SM-556/BPPA0 SM-055/BPPA0 CM-860 patch plug standard V8,ET,TR Patchcable CAT5 (4x) AWG6/7 CE-0700 V.3 dedicated line modem f. 703 CE WT channel modem f. DIN-rail CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/BPPA0 CM-860 patch plug standard V8,ET,TR Patch cable CAT5 (4x) AWG6/7 CP-604 master control element SM-55/BPPA0 CM-860 patch plug standard V8,ET,TR Modem-Cable for TM 703 (e)mic and CE-070x CP-600 emic Master Control Module BPPT0 CP-600 mic Master Control M V.8/8 Mod. CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) SM-55/BPPA0 CM-860 patch plug standard V8,ET,TR Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 T4-53 (5m) / 6MF3040BC530AA0 T4-54 (0m) / 6MF3040BC540AA0 G-00 / 6MF00BC000AA0 G-08 / 6MF00CA80AA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 T4-57 (0.3m) / 6MF3040BC570AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 CA-860/ 6MF0CJ600AA0 TC6-0 / 6MF330GC00AA0 GC6-00 / 6MF30GA00AA0 GC6-00 / 6MF30GA00AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 ACP 703 Platforms, Configuration AU Networks 5 DC0-0-.0, Edition 07.0

26 ESD EARTH FACILITY PS-560 X PUSHTO RELEASE X3 TB X6 NC X7 M -PRE/0 SIM0 X8 M -PRE/ X9 M -PRE/ SI (FB) X0 M -PRE/3 X4 FB X X PUSHTO RE LE ASE X X3 TB X6 NC LOC M-P RE /0 X7 SIM0 M-P RE / SI ( ETO) X8 SI ESD EA RTH FA CILITY X9 M-P RE / SI ( FB) X0 M-P RE /3 X4 FB X X LO C SI /LK /PK SI WD /PK X5 /LK X5 PWR X X3 P S-560 ESD EAR TH FAC ILITY PS -560 Configuration of Automation Networks.. Point-to-point-traffic, IEC , optical IEC Master AK 703 ACP or TM 703 ACP 0-0 x RX TX X4 X6 P US HTO UNLOCK 4-60VDC /LK /P K SI WD /LK /P K X5 X PW R X X RES PU SH TO R ELE AS E COMCPY CM-087 Cable FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre CM-087 s 0-0 x RX TX PUSH TO UNLOCK X4 X6 4-60V DC RES PU SH TO RE LEA SE CO M CPY S I (E TO) TM 703 ACP TM 703 emic AK 703 ACP AK 703 On the CM-087 (from version GA0-87-A on) line-idle state can be selected by a configuration switch Configuration switch CM-087 line-idle state light on line-idle state light off 6 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

27 Configuration of Automation Networks Necessary modules and cables Designation Item Number / MLFB Master AK 703 ACP CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/BPPA0 SM-556 SM-055/BPPA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 Master TM 703 ACP CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-604 master control element CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-04 / 6MF30GA40AA0 SM-55/BPPA0 SM-556 SM-055/BPPA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 Cable AK 703 ACP length: length: CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) FO-INDOORCABLE-50-DUP-LSOH FO-OUTDOORCABLE-50-FIB-ARM FO-CONNECTOR-ST-50/6 FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/BPPA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 TF7-07 TF7-08 TF7-06 TF7-006 TF7-007 TF7-06 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 TM 703 ACP CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-604 master control element CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-04 / 6MF30GA40AA0 SM-55/BPPA0 BC-55 / 6MF030CF50AA0 CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 TM 703 emic TM 703 mic AK 703 CP-600 emic Master Control Module BPPT0 CM-087 fibre optical interface (electrical-fo) Modular coupling RJ-45 9-pol. D-SUB female CP-600 mic Master Control M V.8/8 Mod CM-087 fibre optical interface (electrical-fo) Modular coupling RJ-45 9-pol. D-SUB female CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) GC6-00 / 6MF30GA00AA0 GA0-87 / 6MF0AJ70AA0 TF5-0 / 6MF340FB00AA0 GC6-00 / 6MF30GA00AA0 GA0-87 / 6MF0AJ70AA0 TF5-0 / 6MF340FB00AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 CP-00 systemfunction, processing and CM-858 connection (CP-00) SM-55/BPPA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 BC-55 / 6MF030CF50AA0 CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 ACP 703 Platforms, Configuration AU Networks 7 DC0-0-.0, Edition 07.0

28 ESD EARTH FAC ILITY PS-560 X PU SH TO RE LEA SE X3 TB X6 NC X7 M-P RE /0 SIM0 X8 M-P RE / SI ( ETO) X9 M-P RE / SI ( FB) X X0 M-P RE /3 PUSHTO RELEASE X3 TB X4 FB X X6 NC X7 M-PRE/0 X SIM0 X8 M-PRE/ SI (E TO) ESD EARTH FAC ILITY X9 M-PRE/ SI (FB ) X0 M-PRE/3 LOC SI /L K /PK SI WD X4 FB /L K /PK X5 X X RES PW R X PUSHTO R ELE AS E X3 X LOC SI /LK /PK SI WD /LK /PK X5 X RES PWR X PU SH TO RE LEA SE X3 PS-560 ESD EARTH FA CILITY PS-560 Configuration of Automation Networks..3 Multi-point Traffic, IEC or -03, electrical IEC Zentrale AK 703 ACP oder TM 703 ACP Kabel Patchkabel 0-0 PUSH TO UNLOCK x RX TX CO M CPY 4-60VDC X4 X6 Entfernung > 0 m: mit Plenumkabel über Wanddose oder Patchpanel Modem - Zentrale Modem Übertragungsnetz Modem - Unterstation Kabel, Patchkabel Kabel 3 Modemkabel Modem Modem Modem Modem Modem 3 3 Unterstationen 0-0 TM 703 ACP PUSHTO UNLOCK x RX TX COMCPY 4-60VDC X4 X6 TM 703 emic TM 703 mic AK 703 ACP AK 703 The length of the electrical cable between AK 703 ACP respectively AK 703 and the modem is: max. 5m when the modem is supplied externally (depending on baudrate) max. 3m when modem is supplied internally Hints for establishing an electrical connection of more than 0 m length you can find in the appendix. For modem master and modem slave the same modem types have to be used. Details for supply of the modems you can find in the installation manuals AK 703 ACP, TM 703 ACP, TM 703 emic, TM 703 mic Multi-point traffic according to IEC is not possible with TM 703 emic and TM 703 mic 8 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

29 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP Master TM 703 ACP Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPMA0 03MA0 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 SM-556 SM-055 X X CM-860 patch plug standard V8,ET,TR CP-6004 master control element BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 Cable Modem Master/ AK 703 ACP UMPMA0 03MA0 SM-55 X X BC-55 / 6MF030CF50AA0 SM-556 SM-055 X X CM-860 patch plug standard V8,ET,TR Patchcable CAT5 (4x) AWG6/7 CE-0700 V.3 dedicated line modem f. 703 CE WT channel modem f. DIN-rail CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPSA0 03SA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 T4-53 (5m) / 6MF3040BC530AA0 T4-54 (0m) / 6MF3040BC540AA0 G-00 / 6MF00BC000AA0 G-08 / 6MF00CA80AA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-860 patch plug standard V8,ET,TR CA-860 / 6MF0CJ600AA0 Cable Patch cable CAT5 (4x) AWG6/7 T4-57 (0.3m) / 6MF3040BC570AA0 TM 703 ACP CP-604 master control element UMPSA0 03SA0 GC6-04 / 6MF30GA40AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-860 patch plug standard V8,ET,TR CA-860 / 6MF0CJ600AA0 Cable 3 Modem-Cable for TM 703 mic and CE-070x TC6-0 / 6MF330GC00AA0 TM 703 emic acc. to IEC TM 703 mic acc. to IEC CP-600 emic Master Control Module UMPST0 CP-600 mic Master Control M V.8/8 Mod GC6-00 / 6MF30GA00AA0 GC6-00 / 6MF30GA00AA0 ACP 703 Platforms, Configuration AU Networks 9 DC0-0-.0, Edition 07.0

30 Configuration of Automation Networks AK 703 Designation CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) UMPSA0 03SA0 Item Number / MLFB BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-860 patch plug standard V8,ET,TR CA-860 / 6MF0CJ600AA0 30 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

31 ESD EARTH FACILITY PS-5 60 X PU SH TO RE LEASE X3 TB X6 NC X7 M-PRE/0 SIM0 X8 M-PRE/ SI (ETO) X9 M-PRE/ SI (FB) X0 M-PRE/3 X4 FB X X x RX TX LOC SI /LK /PK SI WD /LK /PK COMCPY X5 X RES PWR 4-60VDC X PU SH TO R ELEASE X3 X PU SH TO RE LEASE X3 TB X6 NC X7 M-PRE/0 SIM0 X8 M-PRE/ SI ( ETO ) ESD EARTH FACILITY X9 M-PRE/ SI ( FB) X0 M-PRE/3 X4 FB X X x RX TX LOC SI /LK /P K SI WD X5 /P K /LK COM CPY X RE S PWR 4-60VDC X PUSHTO R ELEASE X3 PS-560 0, F 0 F / - ES D EARTH FACILITY PS-560 Configuration of Automation Networks..4 Multi-point Traffic, IEC or 03, optical, Star IEC Master AK 703 ACP (redundancy possible) or TM 703 ACP 0-0 X 4 X6 Cable Patchcable, length max. 3 m Cable FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre Fieldbusinterfaces PS-663x, CM-08, CM-08 CM-087 ON PUSH TO UNLOCK OFF Settings on the configuration switch CM-08 -Module B Settings on the configuration switches Cable CM-08 Master-Module A FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre FF CM-087 s 0-0 X4 X6 TM 703 ACP PUSH TO UNLOCK TM 703 emic TM 703 mic BC 703 ACP AK 703 ACP AK 703 Power supply of the fieldbus interfaces PS-663x (redundant power supply is supported, but not to increase power) via the electrical interface direct from the master, if only one fieldbus interface (CM-08) is used With one PS-663x max. 6 fieldbus interfaces CM-08 and/or CM-08 can be supplied. On the CM-087 (from version GA0-87-A on) line-idle state can be selected by a configuration switch Configuration switch CM-087 line-idle state light on line-idle state light off Redundant automation units (masters) are only possible in AK 703 ACP. A redundancy board rack CM-86 (SCA-RS) is necessary. Details you can find in the chapter Redundant Automation Units. Multi-point traffic according to IEC is not possible with TM 703 emic and TM 703 mic. CM-08 master-module A Configuration switch S... Rate 0... OFF... )... Rate... ON... )... e.g. baudrate Rate... OFF... ) 4... Rate 3... ON... ) 5... Star/ring... OFF... star 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state Configuration switch S L... ON... ) master (single) R... ON... ) 0/... ON... Bit word length CM-08 slave-module B... Rate 0... ON... )... Rate... OFF... )... e.g. baudrate Rate... ON... ) 4... Master/slave. ON... slave 5... Level-CH4... OFF... line-idle state 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state ACP 703 Platforms, Configuration AU Networks 3 DC0-0-.0, Edition 07.0

32 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP electrical Master AK 703 ACP redundant optical Master TM 703 ACP Cable Fieldbus interfaces Cable length: length: Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPMA0 03MA0 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 SM-556 SM-055 X X CM-860 patch plug standard V8,ET,TR CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPMA0 03MA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 SM-556 SM-055 X X CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-604 master control element UMPMA0 03MA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-04 / 6MF30GA40AA0 SM-55 X X BC-55 / 6MF030CF50AA0 SM-556 SM-055 X X CM-860 patch plug standard V8,ET,TR Patch cable CAT5 (4x) AWG6/7 CM-08 Fieldbus interface ring (3xFO, xel.) CM-08 Fieldbus interface star (4xFO) FO-INDOORCABLE-50-DUP-LSOH FO-OUTDOORCABLE-50-FIB-ARM FO-CONNECTOR-ST-50/6 FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 GA0-8 / 6MF0AJ0AA0 GA0-8 / 6MF0AJ0AA0 TF7-07 TF7-08 TF7-06 TF7-006 TF7-007 TF ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

33 Configuration of Automation Networks AK 703 ACP TM 703 ACP TM 703 emic acc. to IEC TM 703 mic acc. to IEC Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPSA0 03SA0 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-604 master control element UMPSA0 03SA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-04 / 6MF30GA40AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-600 emic Master Control Module UMPST0 CM-087 fibre optical interface (electrical-fo) Modular coupling RJ-45 9-pol. D-SUB female CP-600 mic Master Control M V.8/8 Mod CM-087 fibre optical interface (electrical-fo) Modular coupling RJ-45 9-pol. D-SUB female CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-00 / 6MF30GA00AA0 GA0-87 / 6MF0AJ70AA0 TF5-0 / 6MF340FB00AA0 GC6-00 / 6MF30GA00AA0 GA0-87 / 6MF0AJ70AA0 TF5-0 / 6MF340FB00AA0 BC 703 ACP CP-504 central processing BC5-04 / 6MF030FA40AA0 acc. to IEC BC 703 ACP acc. to IEC local interface AK 703 SM-55/UMPSA0 CM-5860 Patch Module standard V8,ET CM-087 fibre optical interface (electrical-fo) CP-504 central processing 03SX5 CPCX55 master data for 03SX5 local optical interface on CM-504 available CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) UMPSA0 03SA0 BC-55 / 6MF030CF50AA0 CC5-860 / 6MF30FJ600AA0 GA0-87 / 6MF0AJ70AA0 BC5-04 / 6MF030FA40AA0 SC5-598 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 ACP 703 Platforms, Configuration AU Networks 33 DC0-0-.0, Edition 07.0

34 ESD EARTH FACILITY PS- 560 PU SH TO R ELEASE X X3 TB X6 NC X7 M-PRE/0 SIM0 X8 M-PRE/ SI (ETO ) X9 M-PRE/ SI (FB) X0 M-PRE/3 X4 FB X PUSHTO RELEASE X X X3 TB X6 NC x RX TX LOC X7 M-PRE/0 SI /LK /PK SI SIM0 WD X8 M-PRE/ SI (ETO) ESD EARTH FACILITY X9 M-PRE/ SI (FB) /PK /LK COMCPY RES X5 X PWR 4-60VDC X0 M-PRE/3 X PUSHTO RELEA SE X3 X4 FB X X x RX TX LOC SI /L K /PK SI WD /L K /PK COMCPY X5 X RES X PWR 4-60VDC PUSHTO RELE ASE X3 PS , F 0 F /- ESD EARTH FACILITY PS-56 0 Configuration of Automation Networks..5 Multi-point Traffic, IEC or 03, optical, Ring IEC Master AK 703 ACP or TM 703 ACP Cable Patchcable, length max. 3 m 0-0 PUSH TO UN LO CK X4 X6 Settings on the configuration switches CM-08 Master-Module A ON Fieldbusinterfaces in the ring CM-08 FF CH and CH on CM-08 Cable FO, length:,3km using 6,5/5µm fibre TX X CH X RX TX CH X3 RX X4 Settings on the configuration switches CM-08 -Module B rotate 80 ON Cable Patchcable, length max. 3 m FF s 0-0 TM 703 ACP PUSH TO UNLOC K X4 X6 BC 703 ACP AK 703 ACP AK 703 Power supply of the fieldbus interfaces via the electrical interface direct from the master or slave (SM-x55), if only one fieldbus interface (CM-08) is used Due to the higher data rate in a ring configuration a 6,5/5µm fibre has to be used. CM-08 master-module A Configuration switch S... Rate 0... OFF... )... Rate... ON... )... e.g. baudrate Rate... OFF... ) 4... Rate 3... ON... ) 5... Stern/ring... ON... ring 6... Level-CH3... OFF... line-idle state 7... Level-CH... ON... line-idle state... light on 8... Level-CH... ON... line-idle state... light on Configuration switch S L... ON...) master (single) R... ON...) 0/... ON... Bit word length The local interface of the BC 703 ACP cannot be used in the ring (no failure signalling at ring disturbances). In ring configurations only SM-55 and SM- 055 can be used. CM-08 slave-module B Configuration switch S... Rate 0... OFF...)... Rate... ON...)... e.g. baudrate Rate... OFF...) 4... Rate 3... ON...) 5... Star/ring... ON...ring 6... Level-CH3... OFF...line-idle state 7... Level-CH... ON...line-idle state... light on 8... Level-CH... ON...line-idle state... light on Configuration switch S L...OFF...) R...OFF...) slave 0/...ON... Bit word length 34 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

35 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP Master TM 703 ACP Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPMA0 03MA0 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 SM-556 SM-055 X X CM-860 patch plug standard V8,ET,TR CP-604 master control element BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 Cable UMPMA0 03MA0 SM-55 X X BC-55 / 6MF030CF50AA0 SM-556 SM-055 X X CM-860 patch plug standard V8,ET,TR Patch cable CAT5 (4x) AWG6/7 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Fieldbus interfaces CM-08 fieldbus interface ring (3xFO, xel.) GA0-8 / 6MF0AJ0AA0 Cable AK 703 ACP TM 703 ACP length: FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPSA0 03SA0 TF7-006 TF7-007 TF7-06 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-860 patch plug standard V8,ET,TR CP-604 master control element CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 BC 703 ACP AK 703 UMPSA0 03SA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-860 patch plug standard V8,ET,TR CP-504 central processing UMPSA0 03SA0 CA-860 / 6MF0CJ600AA0 BC5-04 / 6MF030FA40AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-5860 Patch Module standard V8,ET CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) UMPSA0 03SA0 CC5-860 / 6MF30FJ600AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-860 patch plug standard V8,ET,TR CA-860 / 6MF0CJ600AA0 ACP 703 Platforms, Configuration AU Networks 35 DC0-0-.0, Edition 07.0

36 ESD EARTH FAC ILITY ES D EA RTH FA CILITY P S-560 PS-560 X PUSH TO REL EASE X3 TB X6 NC X7 M - PRE/ 0 SI M0 X8 PUSH TO RELEASE X X3 TB X6 NC M-PRE/0 X7 SIM0 M-PRE/ SI ( ETO) X8 X9 M-PRE/ SI ( FB) X0 M-PRE/3 X4 FB X X PUSH TO RELEASE X3 TB X X6 NC M-PRE/0 X7 SIM0 M-PRE/ SI ( ETO) X8 LO C ESD EA RTH FA CILITY X9 M-PRE/ SI ( F B) X0 M-PRE/3 X4 FB X X LOC SI /LK /PK SI WD /LK /PK X5 X RES PWR X PUSH TO RELEASE X3 PS-560 0, F 0 F /- /- 0, F 0 F ESD EARTH FAC ILITY P S-560 ESD EA RTH FA CILITY PS -560 Configuration of Automation Networks..6 Multi-point Traffic, IEC or 03, optical, RingStar IEC Master AK 703 ACP or TM 703 ACP Cable Patchcable, length max. 3 m Fieldbusinterfaces PS-663x, CM-08, CM-08 Cable FO, length max. 0,5km using 50/5µm-fibre,5km using 6,5/5µm-fibre Settings on the configuration switches CM-08 Ring/Master A 0-0 PU SHT OUN L O CK x RX TX COM CPY 4-60 VDC X4 X6 Settings on the configuration switch CM-08 -Module D OFF Cable 3 Ring FO, length max.,3km using 6,5/5µm-fibre 3 3 TX CH X RX TX X TM 703 mic CH X3 RX X4 CH andch oncm-08 Settings on the configuration switches CM-08 Ring/ B Fieldbusinterfaces CM-08 Cable Patchcable, length max. 3 m rotate X4 X6 /L K X /PK WD /L K /PK X5 X5 X3 x RX TX SI SI RES PWR COMCPY PUSH TO REL EASE s TM 703 ACP PUSHT OU NL OC K 4-60VDC BC 703 ACP Cable AK 703 ACP FO, length max. 0,5km using 50/5µm-fibre,5km using 6,5/5µm-fibre Fieldbusinterfaces PS-663x,CM-08 Settings on the configuration switch CM-08 Master-Module C Settings on the configuration switch CM-08 -Module D AK 703 Settings on the configuration switches CM-08 Star/Master E Cable FO, length max. 0,5km using 50/5µm-fibre,5km using 6,5/5µm-fibre s CM-087 Fieldbusinterface CM-08 Cable Patchcable, length max. 3 m 0-0 X4 X X X X4 X6 M- PRE/ X9 M- PRE/ SI (F B) X0 M- PRE/ 3 FB LOC SI /PK /LK SI /PK /LK WD X5 X X3 x RX TX RES PWR PUSHT O RELEASE ON FF TM 703 emic ON FF PUSHT O UNLOCK 4-60VDC CO MCPY OFF SI (ETO) ON OFF FF TM 703 ACP BC 703 ACP AK 703 ACP TM 703 emic TM 703 mic AK ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

37 Configuration of Automation Networks Power supply of the fieldbus interfaces PS-663x (redundant power supply is supported, but not to increase power) via the electrical interface direct from the master or slave, if only one fieldbus interface (CM-08) is used Due to the higher data rate in a ring configuration a 6,5/5µm fibre has to be used. In ring configurations only SM-55 and SM-055 can be used. CM-08 ring/master-module A Configuration switch S...Rate 0...OFF...)...Rate...ON...)...e.g. baudrate Rate...OFF...) 4...Rate 3...ON...) 5...Star/ring...ON...ring 6...Level-CH3...OFF...line-idle state...light off 7...Level-CH...ON...line-idle state...light on 8...Level-CH...ON...line-idle state...light on Configuration switch S L... ON... ) master (single) R... ON... ) 0/... ON... Bit word length CM-08 ring/slave-module B Configuration switch S...Rate 0...OFF...)...Rate...ON...)...e.g. baudrate Rate...OFF...) 4...Rate 3...ON...) 5...Star/ring...ON...ring 6...Level-CH3...OFF...line-idle state...light off 7...Level-CH...ON...line-idle state...light on 8...Level-CH...ON...line-idle state...light on Configuration switch S L... OFF... ) R... OFF... ) slave 0/... ON... Bit word length The local interface of the BC 703 ACP cannot be used in the ring (no failure signalling at ring disturbances). With one PS-663x max. 6 fieldbus interfaces CM-08 and/or CM-08 can be supplied. On the CM-087 (from version GA0-87-A on) line-idle state can be selected by a configuration switch Configuration switch CM-087 line-idle state light on line-idle state light off Multi-point traffic according to IEC is not possible with TM 703 emic, TM 703 mic. CM-08 master-module C... Rate 0... ON... )... Rate... OFF... )... e.g. baudrate Rate... ON... ) 4... Master/slave. OFF... master 5... Level-CH4... OFF... line-idle state 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state CM-08 slave-module D... Rate 0... ON... )... Rate... OFF... )... e.g. baudrate Rate... ON... ) 4... Master/slave. ON... slave 5... Level-CH4... OFF... line-idle state 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state CM-08 star/master-module E Configuration switch S... Rate 0... OFF... )... Rate... ON... )... e.g. baudrate Rate... OFF... ) 4... Rate 3... ON... ) 5... Star/ring... OFF... star 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state Configuration switch S L... ON... ) master (single) R... ON... ) 0/... ON... Bit word length ACP 703 Platforms, Configuration AU Networks 37 DC0-0-.0, Edition 07.0

38 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP Master TM 703 ACP Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPMA0 03MA0 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 SM-556 SM-055 X X CM-860 patch plug standard V8,ET,TR CP-604 master control element BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 RING Cable UMPMA0 03MA0 SM-55 X X BC-55 / 6MF030CF50AA0 SM-556 SM-055 X X CM-860 patch plug standard V8,ET,TR Patch cable CAT5 (4x) AWG6/7 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Fieldbus interfaces CM-08 Fieldbus interface ring (3xFO, xel.) GA0-8 / 6MF0AJ0AA0 Cable 3 AK 703 ACP TM 703 ACP length: FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPSA0 03SA0 TF7-006 TF7-007 TF7-06 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-860 Patch Plug standard V8,ET,TR CP-604 master control element CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 BC 703 ACP AK 703 UMPSA0 03SA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-860 patch plug standard V8,ET,TR CP-504 central processing UMPSA0 03SA0 CA-860 / 6MF0CJ600AA0 BC5-04 / 6MF030FA40AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-5860 Patch Module standard V8,ET CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) UMPSA0 03SA0 CC5-860 / 6MF30FJ600AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-860 patch plug standard V8,ET,TR CA-860 / 6MF0CJ600AA0 38 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

39 Configuration of Automation Networks Designation Item Number / MLFB STAR Cable Patch cable CAT5 (4x) AWG6/7 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Fieldbus interfaces CM-08 fieldbus interface star (4xFO) GA0-8 / 6MF0AJ0AA0 Cable length: length: FO-INDOORCABLE-50-DUP-LSOH FO-OUTDOORCABLE-50-FIB-ARM FO-CONNECTOR-ST-50/6 FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 TF7-07 TF7-08 TF7-06 TF7-006 TF7-007 TF7-06 Fieldbus interfaces CM-08 fieldbus interface star (4xFO) GA0-8 / 6MF0AJ0AA0 AK 703 ACP TM 703 ACP TM 703 emic acc. to IEC TM 703 mic acc. to IEC BC 703 ACP acc. to IEC BC 703 ACP acc. to IEC local interface Cable CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPSA0 03SA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-604 master control element UMPSA0 03SA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-04 / 6MF30GA40AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-600 emic Master Control Module UMPST0 CM-087 fibre optical interface (electrical-fo) Modular coupling RJ-45 9-pol. D-SUB female CP-600 mic Master Control M V.8/8 Mod CM-087 fibre optical interface (electrical-fo) Modular coupling RJ-45 9-pol. D-SUB female CP-504 central processing SM-55/UMPSA0 CM-586 patch plug SM-54 and CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-504 central processing 03SX5 CPCX55 master data for 03SX5 local optical interface on CM-504 available Patch cable CAT5 (4x) AWG6/7 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-00 / 6MF30GA00AA0 GA0-87 / 6MF0AJ70AA0 TF5-0 / 6MF340FB00AA0 GC6-00 / 6MF30GA00AA0 GA0-87 / 6MF0AJ70AA0 TF5-0 / 6MF340FB00AA0 BC5-04 / 6MF030FA40AA0 BC-55 / 6MF030CF50AA0 CC5-86 / 6MF30FJ60AA0 GA0-87 / 6MF0AJ70AA0 BC5-04 / 6MF030FA40AA0 SC5-598 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Fieldbus interfaces CM-08 fieldbus interface ring (3xFO, xel.) GA0-8 / 6MF0AJ0AA0 AK 703 CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) UMPSA0 03SA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-860 patch plug standard V8,ET,TR CA-860 / 6MF0CJ600AA0 ACP 703 Platforms, Configuration AU Networks 39 DC0-0-.0, Edition 07.0

40 ESD EA RTH FA CILITY PS-560 PUSH TO RELEASE X X3 TB X6 NC X7 M-PRE/0 SI M0 X8 M-PRE/ SI (ETO) X9 M-PRE/ SI (FB) X0 M-PRE/3 X4 FB X X LO C SI /LK /PK SI WD /LK /PK X5 X RES PWR X PUSH TO RELEASE X3 PUSHTO RELEASE X X3 TB X6 NC M-PRE/0 X7 SIM0 M-PRE/ SI (ETO) X8 ESD EAR TH FA CILITY X9 M-PRE/ SI (FB) X0 M-PRE/3 X4 FB X X LO C 0 SI /LK /PK SI WD /LK /PK X5 X , F RES 0 PWR X PUSH TO RELEASE F /- X3 P S-560 ESD EA RTH FACILITY PS-560 Configuration of Automation Networks..7 Multi-point Traffic, IEC or 03, optical, Tree IEC Master AK 703 ACP (redundancy possible) or TM 703 ACP Cable Patchcable, length max. 3 m Cable FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre Fieldbusinterfacs PS-663x, CM-08, CM-08 CM-087 Settings on the configurataion switches CM-08 Master-Module A 0-0 ON PUSH TO UNLOCK x RX TX CO MCPY 4-60VDC X4 X6 Cable FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre FF Settings on the configurataion switch CM-08 -Module C Fieldbusinterfaces PS-663x, CM-08 Settings on the configurataion switch CM-08 Master-Module B OFF OFF Fieldbusinterfaces PS-663x, CM-08 TM 703 emic CM-087 Cable FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre TM 703 mic CM-087 s 0-0 PUSHTOUNLOCK x RX TX CO MCPY 4-60VDC X4 X6 AK 703 TM 703 ACP BC 703 ACP AK 703 ACP 40 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

41 Configuration of Automation Networks Power supply of the fieldbus interfaces PS-663x (redundant power supply is supported, but not to increase power) via the electrical interface direct from the master, if only one fieldbus interface (CM-08) is used With one PS-663x max. 6 fieldbus interfaces CM-08 and/or CM-08 can be supplied. On the CM-087 (from version GA0-87-A on) line-idle state can be selected by a configuration switch Configuration switch CM-087 line-idle state light on line-idle state light off Multi-point traffic according to IEC is not possible with TM 703 emic, TM 703 mic. Redundant automation units (masters) are only possible in AK 703 ACP. A redundancy board rack CM-86 (SCA-RS) is necessary. Details you can find in the chapter Redundant Automation Units. CM-08 master-module A Configuration switch S... Rate 0... OFF... )... Rate... ON... )... e.g. baudrate Rate... OFF... ) 4... Rate 3... ON... ) 5... Star/ring... OFF... star 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state Configuration switch S L... ON... ) master (single) R... ON... ) 0/... ON... Bit word length CM-08 master-module B... Rate 0... ON... )... Rate... OFF... )... e.g. baudrate Rate... ON... ) 4... Master/slave. OFF... master 5... Level-CH4... OFF... line-idle state 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state CM-08 slave-module C... Rate 0... ON... )... Rate... OFF... )... e.g. baudrate Rate... ON... ) 4... Master/slave. ON... slave 5... Level-CH4... OFF... line-idle state 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state ACP 703 Platforms, Configuration AU Networks 4 DC0-0-.0, Edition 07.0

42 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP electrical Master AK 703 ACP redundant optical Master TM 703 ACP Cable Cable length: length: Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPMA0 03MA0 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 SM-556 SM-055 X X CM-860 patch plug standard V8,ET,TR CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPMA0 03MA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 SM-556 SM-055 X X CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-604 master control element UMPMA0 03MA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-04 / 6MF30GA40AA0 SM-55 X X BC-55 / 6MF030CF50AA0 SM-556 SM-055 X X CM-860 patch plug standard V8,ET,TR Patch cable CAT5 (4x) AWG6/7 FO-INDOORCABLE-50-DUP-LSOH FO-OUTDOORCABLE-50-FIB-ARM FO-CONNECTOR-ST-50/6 FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 TF7-07 TF7-08 TF7-06 TF7-006 TF7-007 TF7-06 Fieldbus interfaces CM-08 fieldbus interface ring (3xFO, xel.) GA0-8 / 6MF0AJ0AA0 CM-08 fieldbus interface star (4xFO) GA0-8 / 6MF0AJ0AA0 4 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

43 Configuration of Automation Networks AK 703 ACP TM 703 ACP TM 703 emic acc. to IEC TM 703 mic acc. to IEC BC 703 ACP acc. to IEC BC 703 ACP acc. to IEC local interface AK 703 Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) UMPSA0 03SA0 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-604 master control element UMPSA0 03SA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-04 / 6MF30GA40AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-600 emic Master Control Module UMPST0 CM-087 fibre optical interface (electrical-fo) Modular coupling RJ-45 9-pol. D-SUB female CP-600 mic Master Control M V.8/8 Mod CM-087 fibre optical interface (electrical-fo) Modular coupling RJ-45 9-pol. D-SUB female CP-504 central processing SM-55/UMPSA0 CM-586 patch plug SM-54 and CM-08/7 CM-087 Fibre optical interface (electrical-fo) CP-504 central processing 03SX5 CPCX55 master data for 03SX5 local optical interface on CM-504 available CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) UMPSA0 03SA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA GC6-00 / 6MF30GA00AA0 GA0-87 / 6MF0AJ70AA0 TF5-0 / 6MF340FB00AA0 GC6-00 / 6MF30GA00AA0 GA0-87 / 6MF0AJ70AA0 TF5-0 / 6MF340FB00AA0 BC5-04 / 6MF030FA40AA0 BC-55 / 6MF030CF50AA0 CC5-86 / 6MF30FJ60AA0 GA0-87 / 6MF0AJ70AA0 BC5-04 / 6MF030FA40AA0 SC5-598 BA-000 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 SM-55 X X BC-55 / 6MF030CF50AA0 CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 ACP 703 Platforms, Configuration AU Networks 43 DC0-0-.0, Edition 07.0

44 DRS LIGHT DRS LIGHT 0, F 0 F /- Configuration of Automation Networks..8 Multi-point Traffic, IEC , optical, s IEC Master BC 703 ACP Cable Patchcable, length max. 3 m Fieldbus interface CM-08 Settings on the configurataion switches CM-08 Master-Module A ON FF Cable FO, length: 0.5km using 50/5µm fibre.5km using 6,5/5µm fibre Protective devices Main application of this configuration: Coupling of (non-siemens) protective devices in the bay level Supply of the fieldbus interface: via the electrical interface direct from the master if only one fieldbus interface (CM-08) is used. CM-08 master-module A Configuration switch S... Rate 0... OFF...)... Rate... ON...)... e.g. baudrate Rate... OFF...) 4... Rate 3... ON...) 5... Star/ring... OFF...star 6... Level-CH3... OFF...line-idle state 7... Level-CH... OFF...line-idle state 8... Level-CH... OFF...line-idle state Configuration switch S L...ON...) master (single) R...ON...) 0/...ON... Bit word length 44 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

45 Configuration of Automation Networks Necessary modules and cables Master BC 703 ACP Designation CP-504 central processing Item Number / MLFB BC5-04 / 6MF030FA40AA0 Cable with SM-546 ETA 03MA0 SM-546 SM-055 CM-586 patch plug standard ET 00 FX with SM-556 ETA 03MA0 SM-556 SM-055 CM-5860 patch plug standard V8,ET Patch cable CAT5 (4x) AWG6/7 X X X X BC-546 / 6MF030CF460AA0 BC0-55 / 6MF030AF50AA0 CC5-86 / 6MF30FJ60AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CC5-860 / 6MF30FJ600AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Fieldbus interface CM-08 fieldbus interface ring (3xFO, xel.) GA0-8 / 6MF0AJ0AA0 Cable length: length: FO-INDOORCABLE-50-DUP-LSOH FO-OUTDOORCABLE-50-FIB-ARM FO-CONNECTOR-ST-50/6 FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 TF7-07 TF7-08 TF7-06 TF7-006 TF7-007 TF7-06 ACP 703 Platforms, Configuration AU Networks 45 DC0-0-.0, Edition 07.0

46 DRS LIGHT DRS LIG HT DRS LIGHT DRS LIGHT 0 0,, F F 0 0 F / - F /- /- DRS LIG HT 0, F 0 F PUSH TO RELEAS E X X3 TB X6 NC X7 M-PRE/0 SIM0 X8 M-PRE/ SI (ETO) X9 M-PRE/ SI (FB) X0 M-PRE/3 X4 FB X X x RX TX LOC SI /PK / LK SI /PK / LK COMCPY RES WD X5 X PWR 4-60VDC X PU SH TO RE LEASE X3 DRS LIGHT DRS LIGHT DRS LIG HT ESD EARTH FACILITY 0, F 0 F / - PS-56 0 DRS LIG HT DRS LIGHT DRS LIG HT DRS LIGHT DRS LIG HT DRS LIGHT DRS LIGHT 0, F 0 F /- DRS LIGHT DRS LIGHT DRS LIGHT DRS LIGHT Configuration of Automation Networks..9 Methods for Coupling of (non-siemens) Protective Devices in Ring Configurations IEC Master AK 703 ACP, TM 703 ACP, BC 703 ACP Cable Patchcable, length max. 3 m Cable FO, length:.3km using 6,5/5µm fibre Cable 3 FO, length: 0.5km using 50/5µm fibre.5km using 6,5/5µm fibre Cable 4 RS485 interface: screened cable necessary length max. 500 m or 50 m if RS485 interface of slave is supplied Cable 5 information ring monitoring 0-0 PUSH TO U NLO CK CM-08 Module B X4 X6 CM-08 Master Module A CM-08 Module D CM-083 Module C CM-08 Module B CM-083 Module C CM-089 CM-08 Module B CM-08 Module D CM-083 Module C 4 6 CM-083 Module C CM-083 Module C 5 CM-083 Module C ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

47 Configuration of Automation Networks By performance reasons recommended number of protective devices in the ring on one 03-master interface: 0 protective devices transmission only in signalling direction 0 5 protective devices transmission in control direction and signalling direction CM-08 master-module A Configuration switch S...Rate 0...OFF...)...Rate...ON...)...e.g. baudrate Rate...OFF...) 4...Rate 3...ON...) 5...Star/ring...ON...ring 6...Level-CH3...OFF...line-idle state...light off 7...Level-CH...ON...line-idle state...light on 8...Level-CH...ON...line-idle state...light on Configuration switch S L... ON... ) master (single) R... ON... ) 0/... ON... Bit word length CM-08 slave-module B Configuration switch S...Rate 0...OFF...)...Rate...ON...)...e.g. baudrate Rate...OFF...) 4...Rate 3...ON...) 5...Star/ring...ON...ring 6...Level-CH3...OFF...line-idle state...light off 7...Level-CH...ON...line-idle state...light on 8...Level-CH...ON...line-idle state...light on Configuration switch S L... OFF... ) R... OFF... ) slave 0/... ON... Bit word length CM-083 slave-module C Configuration switch S... Rate 0... OFF... )... Rate... ON... )... e.g. baudrate Rate... OFF... ) 4... Rate 3... ON... ) 5... star/ring... ON... ring 6... Level-CH3... OFF... line-idle state 7... Level-CH... ON... line-idle state... light on 8... Level-CH... ON... line-idle state... light on Configuration switch S L... OFF... ) R... OFF... ) slave 0/... ON... Bit word length BT... ON/OFF... with/without bus termination The description of the configuration switches on the CM-083 you can find in the data sheet CM-083. CM-08 slave-module D... Rate 0... ON... )... Rate... OFF... )... e.g. baudrate Rate... ON... ) 4... Master/slave. ON... slave 5... Level-CH4... OFF... line-idle state 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state ACP 703 Platforms, Configuration AU Networks 47 DC0-0-.0, Edition 07.0

48 Configuration of Automation Networks Method Cable Cable Cable 3 Cable 4 Cable 5 CM-08 CM-08 CM-083 CM-089 PS-66xx protective device (PD) electrical X X X PD electrical, PD optical X X X X 3 PD electrical, n PD RS485 X X X X X 4 PD RS 485 X X X X X 5 n PD RS485 X X X X X 6 PD optical X X X X X 7 n PD optical X X X X X X 8 PD optical, n PD RS485 X X X X X X 9 PD RS485, n PD optical X X X X X X X 48 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

49 Configuration of Automation Networks Necessary modules and cables MAST Designation Item Number / MLFB BC 703 ACP CP-504 central processing BC5-000 / 6MF030FA40AA0 AK 703 ACP with SM-546 SM-546 SM-055/03MA0 CM-586 patch plug standard ET 00 FX with SM-556 SM-556 SM-055/03MA0 CM-5860 patch plug standard V8,ET CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/03MA0 SM-556 SM-055/03MA0 CM-860 patch plug standard V8,ET,TR BC-546 / 6MF030CF460AA0 BC0-55 / 6MF030AF50AA0 CC5-86 / 6MF30FJ60AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CC5-860 / 6MF30FJ600AA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 TM 703 ACP CP-604 master control element GC6-04 / 6MF30GA40AA0 PROTECTIVE DEVICES BC 703 ACP optical acc. to IEC local interface BC 703 ACP electrical SM-55/03MA0 SM-556 SM-055/03MA0 CM-860 patch plug standard V8,ET,TR CP-504 central processing 03SX5 CPCX55 master data for 03SX50 local optical interface on CP-504 available CP-504 central processing SM-55/03SA0 CM-5860 patch plug standard V8,ET BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 BC5-04 / 6MF030FA40AA0 SC5-598 BC5-04 / 6MF030FA40AA0 BC-55 / 6MF030CF50AA0 CC5-860 / 6MF30FJ600AA0 Cable Patch cable CAT5 (4x) AWG6/7 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Cable length: FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 Cable 3 length: FO-INDOORCABLE-50-DUP-LSOH FO-OUTDOORCABLE-50-FIB-ARM FO-CONNECTOR-ST-50/6 length: FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 Cable 4 length: RS485 interface: screened cable necessary Cable 5 Information ring monitoring TF7-006 TF7-007 TF7-06 TF7-07 TF7-08 TF7-06 TF7-006 TF7-007 TF7-06 Fieldbus interfaces CM-08 fieldbus interface ring (3xFO, xel.) GA0-8 / 6MF0AJ0AA0 CM-08 fieldbus interface star (4xFO) CM-083 fieldbus interface ring (3xFO, xrs485) CM-089 RS3/RS4; RS485 converter GA0-8 / 6MF0AJ0AA0 GA0-83 / 6MF0AJ30AA0 GA0-89 / 6MFAJ00AA0 ACP 703 Platforms, Configuration AU Networks 49 DC0-0-.0, Edition 07.0

50 ESD EA RTH FACILITY PS-560 PUSH TO REL EASE X X3 TB X6 NC M-PRE/0 SI 0 X7 SIM 0 M-PRE/ X8 X9 M-PRE/ SI (F B) X0 M-PRE/3 SI 3 X4 FB X PUSH TO RELEASE X X X3 TB X6 NC LOC M- PRE/0 X7 SIM 0 M- PRE/ X8 SI /L K /PK SI WD ES D EA RTH FA CILITY /L K /PK X5 X X9 M- PRE/ SI (F B) X0 M- PRE/3 X4 FB X X LOC SI /LK /PK SI WD /LK /PK X5 X5 PWR X X3 P S-560 ES D EA RTH FAC ILITY PS -560 Configuration of Automation Networks..0 Dial-up Traffic analog/gsm, IEC IEC Master AK 703 ACP or TM 703 ACP 0-0 x RX TX X4 X6 PUSH TO UNLOCK 4-60VDC RES COMCPY SI (ETO) RE S PWR X PUSH TO RELEASE X PUSH TO REL EASE Cable Modem - Master Modem Modem - Modem Modem Modem Modem Modem Cable s 0-0 SI (ETO) PUSHT O UNLOCK x RX TX COMCP Y X4 X6 4-60VDC TM 703 ACP TM 703 emic TM 703 mic AK 703 ACP AK 703 Details for supply of the modems you can find in the installation manuals AK 703 ACP, TM 703 ACP, TM 703 emic and TM 703 mic The list shows which modem types can be used together: Westermo TDW-33, TD-36 analog Westermo TDW-33, TD-36 Eurocom4 MAST Centerion MC5iT Westermo GDW- analog analog GSM GSM X SLAVE Eurocom4 analog X X Cinterion MC5iT Westermo GDW- GSM X X X GSM X X X 50 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

51 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP Master TM 703 ACP Cable Cable Modems AK 703 ACP TM 703 ACP TM 703 emic TM 703 mic AK 703 Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/DIAMA0 SM-556 SM-055/DIAMA0 CM-860 patch plug standard V8,ET,TR CP-604 master control element SM-55/DIAMA0 SM-556 SM-055/DIAMA0 CM-860 patch plug standard V8,ET,TR circuitry you can find in the installation manual AK 703 ACP or TM 703 ACP Eurocom4: can be plugged on Westermo: circuitries you can find in the installation manual TM 703 mic Siemens: Modem-Cable TM 703 mic for TC35 modem Westermo TDW-33 Westermo TD-36 Westermo GDW- Eurocom4 Cinterion MC5iT CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/DIASA0 CM-860 patch plug standard V8,ET,TR CP-604 master control element SM-55/DIASA0 CM-860 patch plug standard V8,ET,TR CP-600 emic Master Control Module DIAST0 CP-600 mic Master Control M V.8/8 Mod if using Eurocom4 modem: D-SUB 9-pin connector locking CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) SM-55/DIASA0 CM-860 patch plug standard V8,ET,TR Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 TC6- / 6MF330GC0AA0 BC-00/ 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 GC6-00 / 6MF30GA00AA0 GC6-00 / 6MF30GA00AA0 TC6- / 6MF330GC0AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 ACP 703 Platforms, Configuration AU Networks 5 DC0-0-.0, Edition 07.0

52 ESD EAR TH FAC ILI TY PS -560 PUSH TO REL EASE X X3 TB X6 NC M-PRE/0 X7 SIM 0 M-PRE/ X8 X9 M-PRE/ SI (F B) X0 M-PRE/3 X PUSH TO REL EASE X4 X3 TB X6 NC M-PRE/0 X7 SIM0 M-PRE/ X8 ESD EAR TH FAC ILITY X9 X4 PS -560 ES D EA RTH FAC ILITY PS -560 Configuration of Automation Networks.. Dial-up Traffic ISDN, IEC IEC Master AK 703 ACP or TM 703 ACP 0-0 x RX TX X4 X6 X X X M-PRE/ SI (F B) X0 M-PRE/3 FB LOC SI /PK /L K SI /PK /L K WD X5 X5 X SI (ETO) PUSH T O UNLOCK 4-60VDC RES PWR COM CPY PUSHTO REL EASE Cable Modem - Master Modem Modem - Modem Modem Modem Modem Cable 0-0 X4 X6 FB X X X LOC SI /PK /L K SI /PK /L K WD X5 X x RX TX RES X3 PWR PUSHTO REL EASE Modem SI (ETO) COMCPY TM 703 ACP PUSH T O UNLOCK 4-60VDC TM 703 emic TM 703 mic AK 703 ACP AK 703 Details for supply of the modems you can find in the installation manuals AK 703 ACP, TM 703 ACP, TM 703 mic The list shows which modem types can be used together: MAST Westermo IDW-90 SLAVE Westermo IDW-90 X 5 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

53 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP Master TM 703 ACP Cable Cable Modems AK 703 ACP TM 703 ACP TM 703 emic TM 703 mic AK 703 Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/DIAMA0 SM-556 SM-055/DIAMA0 CM-860 patch plug standard V8,ET,TR CP-604 master control element SM-55/DIAMA0 SM-556 SM-055/DIAMA0 CM-860 patch plug standard V8,ET,TR circuitry you can find in the installation manual AK 703 ACP or TM 703 ACP circuitry you can find in the installation manual TM 703 emic and TM 703 mic Westermo IDW-90 CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/DIASA0 CM-860 patch plug standard V8,ET,TR CP-604 master control element SM-55/DIASA0 CM-860 patch plug standard V8,ET,TR CP-600 emic Master Control Module DIAST0 CP-600 mic Master Control M V.8/8 Mod CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) SM-55/DIASA0 CM-860 patch plug standard V8,ET,TR Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 GC6-00 / 6MF30GA00AA0 GC6-00 / 6MF30GA00AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 ACP 703 Platforms, Configuration AU Networks 53 DC0-0-.0, Edition 07.0

54 ESD EAR TH FACILITY PS-560 PUSHTO REL EASE X X3 TB X6 NC M-PRE/0 X7 S IM0 M-PRE/ SI (E TO) X8 X9 M-PRE/ SI (FB ) X 0 M-PRE/3 X4 FB PUSHT O REL EASE X X X3 TB X X6 NC X7 X8 M-PRE/0 SIM0 M-PRE/ SI (E TO) ESD EARTH FACILITY X9 M-PRE/ SI (FB ) LOC SI /PK /L K SI /PK /L K WD X 0 M-PRE/3 X4 FB X X LOC SI /PK /L K SI /PK /L K WD X5 X5 WEST MO ID-90 LV ISDN PWR X X3 PS -560 ESD EARTH FACILITY PS-560 Configuration of Automation Networks.. Dial-up Traffic analog/gsm/isdn, IEC IEC Master AK 703 ACP or TM 703 ACP P US HTO UNLOCK 0-0 x RX TX X4 X6 4-60VDC X5 X RES PW R X PUSH TO RELEASE X3 RES PUSHT O REL EASE COMCPY Cable Modem - Master Westermo IDW-90 Modem - Modem Modem Modem Modem Modem Cable s 0-0 TM 703 ACP PUSHTO UNLOCK x RX TX COMC PY 4-60VDC X4 X6 TM 703 emic TM 703 mic AK 703 ACP AK 703 The list shows which modem types can be used together: Details for supply of the modems you can find in the installation manuals AK 703 ACP, TM 703 ACP, TM 703 emic and TM 703 mic SLAVE MAST Westermo IDW-90 Westermo TDW-33 analog X Westermo TD-36 analog X Eurocom4 analog X Cinterion MC5iT GSM X Westermo IDW-90 ISDN X 54 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

55 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP Master TM 703 ACP Cable Cable Modem Master Modem AK 703 ACP TM 703 ACP TM 703 emic TM 703 mic AK 703 Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/DIAMA0 SM-556 SM-055/DIAMA0 CM-860 patch plug standard V8,ET,TR CP-604 master control element SM-55/DIAMA0 SM-556 SM-055/DIAMA0 CM-860 patch plug standard V8,ET,TR circuitry you can find in the installation manual AK 703 ACP or TM 703 ACP Eurocom4: can be plugged on Westermo: circuitries you can find in the installation manual TM 703 mic Siemens: Modem-Cable TM 703 mic for TC35 modem Westermo IDW-90 Westermo TWD-33 Westermo TD-36 Westermo IDW-90 Eurocom4 Cinterion MC5iT CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/DIASA0 CM-860 patch plug standard V8,ET,TR CP-604 master control element SM-55/DIASA0 CM-860 patch plug standard V8,ET,TR CP-600 emic Master Control Module DIAST0 CP-600 mic Master Control M V.8/8 Mod if using Eurocom4 modem: D-SUB 9-pin connector locking CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) SM-55/DIASA0 CM-860 patch plug standard V8,ET,TR Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 TC6- / 6MF330GC0AA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 GC6-00 / 6MF30GA00AA0 GC6-00 / 6MF30GA00AA0 TC6- / 6MF330GC0AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 ACP 703 Platforms, Configuration AU Networks 55 DC0-0-.0, Edition 07.0

56 X PUS H TO REL EASE X3 TB X6 NC X7 M-PRE/0 SIM0 X8 M-PRE/ SI (ETO) ESD EAR TH FACILITY X9 M-PRE/ SI (FB) X 0 M-PRE/3 X4 FB X X x RX TX LOC SI /P K /LK SI /P K /LK COM CPY WD X5 X RES PWR 4-60V DC X PUSHTO R ELE AS E X 3 PS ESD EARTH FACILITY PS , F 0 F /- X PU SH TO RE LEAS E X3 TB X6 NC X7 M-PRE/0 SIM0 X8 M-PRE/ SI (E TO) X9 M-PRE/ SI (FB ) X0 M-PRE/3 X4 FB X X x RX TX LOC SI /PK /LK SI /PK /LK CO MCPY WD X5 X RES PWR 4-60VDC X PUS H T O REL EAS E X3 ESD EAR TH FA CILITY PS Configuration of Automation Networks..3 SIEMENS Fieldbus, IEC , electrical IEC AK 703 ACPTM 703 ACP with SM-55 Master AK 703 ACP or TM 703 ACP Cable Patchcable 0-0 P USH TOUNLOCK X4 X 6 Setting of operation mode Converter CM EF 3 D 4 C A MODE Signal Cable length max.,km bus terminator bus terminator Setting of operation mode Converter CM-089 Cable Patchcable 0 EF 3 D 4 C A MODE s BC 703 ACP with SM TM 703 ACP with SM-54 PUS HTO UNLOCK X 4 X6 AK 703 ACP with SM-54 AK 703 ACP with SM-55 AK 703 with SM-54 The baudrate of the fieldbus is max Bd. With AK 703 ACP, TM 703 ACP and AK 703 the Converter CM-089 is necessary when using SM-x55 (with patchplugs). Attention: At start and end of the fieldbus a bus terminator has to be set (by operation mode switch on the CM-089). Setting of the operation mode 0 RS-485 two-wire with bus terminator RS-485 two-wire without bus terminator Settings of the mode switch can be found in the appendix. 56 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

57 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP Master TM 703 ACP Cable AK 703 ACP TM 703 ACP BC 703 ACP AK 703 Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/SFBMA SM-556 SM-055/SFBMA CM-860 patch plug standard V8,ET,TR CM-089 RS3/RS4; RS485 Converter CP-604 master control element SM-55/SFBMA SM-556 SM-055/SFBMA CM-860 patch plug standard V8,ET,TR CM-089 RS3/RS4; RS485 Converter Patch cable CAT5 (4x) AWG6/7 CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/SFBSA CM-860 patch plug standard V8,ET,TR CM-089 RS3/RS4; RS485 Converter CP-604 master control element SM-55/SFBSA CM-860 patch plug standard V8,ET,TR CM-089 RS3/RS4; RS485 Converter CP-504 central processing SM-55/SFBSA CM-5860 patch plug standard V8,ET CM-089 RS3/RS4; RS485 Converter CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 GA0-89 / 6MFAJ00AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 GA0-89 / 6MFAJ00AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 T4-53 (5m) / 6MF3040BC530AA0 T4-54 (0m) / 6MF3040BC540AA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 GA0-89 / 6MFAJ00AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 GA0-89 / 6MFAJ00AA0 BC5-04 / 6MF030FA40AA0 BC-55 / 6MF030CF50AA0 CC5-860 / 6MF30FJ600AA0 GA0-89 / 6MFAJ00AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 CP-00 systemfunction, processing and CM-858 connection (CP-00) SM-55/SFBSA CM-860 patch plug standard V8,ET,TR CM-089 RS3/RS4; RS485 Converter BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 GA0-89 / 6MFAJ00AA0 ACP 703 Platforms, Configuration AU Networks 57 DC0-0-.0, Edition 07.0

58 ESD EAR TH FA CILITY PS-560 PUSH TO RELEASE X X3 TB X6 NC X7 M-PRE /0 SIM0 X8 M-PRE / SI ( ETO) X9 M-PRE / SI ( FB ) X0 M-PRE /3 X4 FB X X LOC SI /LK /PK SI WD /LK /PK X5 X RES PW R X PUSHT O RELEASE X3 PUSH TO RELEASE X X3 TB X6 NC M-PRE/0 X7 SIM0 M-PRE/ X8 ESD EAR TH FA CILITY X9 M-PRE/ S I (F B) X0 M-PRE/3 X4 FB X X LOC SI /LK /PK SI WD /PK X5 /LK X5 RES PW R X X3 PS-560 ESD EA RTH FA CILITY PS -560 Configuration of Automation Networks..4 SIEMENS Fieldbus, IEC , optical, Star IEC Master AK 703 ACP (redundancy possible) or TM 703 ACP 0-0 x RX TX COMCPY X4 X6 Cable Patchcable, length max. 3 m Cable FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre Fieldbusinterfaces PS-663x, CM-08, CM-08 CM-087 S I (E TO) , PUSHTO RELEASE F 0 F /- ON P US H TO UNLOCK 4-60V DC Settings on the configuration switch CM-08 -Module B OFF Settings on the configuration switches Cable CM-08 Master-Module A FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre FF CM-087 s 0-0 P US H TO UNLO CK x RX TX COMCPY 4-60V DC X4 X6 TM 703 ACP BC 703 ACP AK 703 ACP AK ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

59 Configuration of Automation Networks Power supply of the fieldbus interfaces PS-663x (redundant power supply is supported, but not to increase power) via the electrical interface direct from the master, if only one fieldbus interface (CM-08) is used With one PS-663x max. 6 fieldbus interfaces CM-08 and/or CM-08 can be supplied. On the CM-087 (from version GA0-87-A on) line-idle state can be selected by a configuration switch Configuration switch CM-087 line-idle state light on line-idle state light off Redundant automation units (masters) are only possible in AK 703 ACP. A redundancy board rack CM-86 (SCA-RS) is necessary. Details you can find in the chapter Redundant Automation Units. CM-08 master-module A Configuration switch S... Rate 0... ON... )... Rate... ON... )... e.g. baudrate Rate... OFF... ) 4... Rate 3... ON... ) 5... Star/ring... OFF... star 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state Konfigurationsschalter S L... ON... ) master (single) R... ON... ) 0/... ON... Bit word length CM-08 slave-module B... Rate 0... OFF... )... Rate... ON... )... e.g. baudrate , etc Rate... ON... ) 4... Master/slave. ON... slave 5... Level-CH4... OFF... line-idle state 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state ACP 703 Platforms, Configuration AU Networks 59 DC0-0-.0, Edition 07.0

60 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP electrical Master AK 703 ACP redundant optical Master TM 703 ACP Cable Cable length: length: Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/SFBMA SM-556 SM-055/SFBMA CM-860 patch plug standard V8,ET,TR CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/SFBMA SM-556 SM-055/SFBMA CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-604 master control element SM-55/SFBMA SM-556 SM-055/SFBMA CM-860 patch plug standard V8,ET,TR Patch cable CAT5 (4x) AWG6/7 FO-INDOORCABLE-50-DUP-LSOH FO-OUTDOORCABLE-50-FIB-ARM FO-CONNECTOR-ST-50/6 FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 TF7-07 TF7-08 TF7-06 TF7-006 TF7-007 TF7-06 Fieldbus interfaces CM-08 fieldbus interface ring (3xFO, xel.) GA0-8 / 6MF0AJ0AA0 CM-08 fieldbus interface star (4xFO) GA0-8 / 6MF0AJ0AA0 60 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

61 Configuration of Automation Networks AK 703 ACP TM 703 ACP BC 703 ACP AK 703 Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/SFBSA CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-604 master control element SM-55/SFBSA CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-504 central processing SM-55/SFBSA CM-586 patch plug SM-54 and CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) SM-55/SFBSA CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 BC5-04 / 6MF030FA40AA0 BC-55 / 6MF030CF50AA0 CC5-86 / 6MF30FJ60AA0 GA0-87 / 6MF0AJ70AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 BC-55 / 6MF030CF50AA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 ACP 703 Platforms, Configuration AU Networks 6 DC0-0-.0, Edition 07.0

62 ESD EARTH FACILITY PS-56 0 X PUSHTO RELEASE X3 TB X6 NC X7 M-PRE/0 SIM0 X8 M-PRE/ SI (ETO) X9 M-PRE/ SI (FB) X0 M-PRE/3 X4 FB X PUSHTO RELE ASE X X3 TB X X6 NC X7 M-PR E/0 SIM0 X8 M-PR E/ SI(ETO) x RX TX LOC ESD EARTH FACILITY SI X9 M-PR E/ SI(FB) /LK /PK SI WD /LK /PK COMCPY X 0 M-PR E/3 X5 X RES X4 FB PWR 4-60VDC X PUSHTO RELE ASE X3 X X x RX TX LOC SI /LK /PK SI WD X5 /PK /LK COMCPY RES X PWR 4-60VDC X PU SH TO RE LEAS E X3 PS , F 0 F /- ESD EARTH FACILITY PS-56 0 Configuration of Automation Networks..5 SIEMENS Fieldbus, IEC , optical, Ring IEC Master AK 703 ACP or TM 703 ACP Cable Patchcable, length max. 3 m 0-0 PUSH TO U NLOCK X4 X6 Settings on the configuration switches CM-08 Master-Module A ON Fieldbusinterfaces in the ring CM-08 FF CH and CH on CM-08 Cable FO, length:,3km using 6,5/5µm fibre TX X CH X RX TX CH X3 Settings on the configuration switches CM-08 -Module B rotate 80 ON RX X4 Cable Patchcable, length max. 3 m FF s 0-0 TM 703 ACP P USH TO UN LO CK X4 X6 BC 703 ACP AK 703 ACP AK 703 Power supply of the fieldbus interfaces via the electrical interface direct from the master or slave (SM-x55), if only one fieldbus interface (CM-08) is used Due to the higher data rate in a ring configuration a 6,5/5µm fibre has to be used. CM-08 master-module A Configuration switch S... Rate 0... ON... )... Rate... ON... )... e.g. baudrate Rate... OFF... ) 4... Rate 3... ON... ) 5... Star/ring... ON... ring 6... Level-CH3... OFF... line-idle state 7... Level-CH... ON... line-idle state... light on 8... Level-CH... ON... line-idle state... light on Configuration switch S L...ON...) master (single) R...ON...) 0/...ON... Bit word length The local interface of the BC 703 ACP cannot be used in the ring (no failure signalling at ring disturbances). In ring configurations only SM-55 and SM-055 can be used. CM-08 master-module B Configuration switch S... Rate 0... ON...)... Rate... ON...)... e.g. baudrate Rate... OFF...) 4... Rate 3... ON...) 5... Star/ring... ON...ring 6... Level-CH3... OFF...line-idle state 7... Level-CH... ON...line-idle state... light on 8... Level-CH... ON...line-idle state... light on Configuration switch S L...OFF...) R...OFF...) slave 0/...ON... Bit word length 6 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

63 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP Master TM 703 ACP Cable Cable length: Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/SFBMA SM-556 SM-055/SFBMA CM-860 patch plug standard V8,ET,TR CP-604 master control element SM-55/SFBMA SM-556 SM-055/SFBMA CM-860 patch plug standard V8,ET,TR Patch cable CAT5 (4x) AWG6/7 FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 TF7-006 TF7-007 TF7-06 Fieldbus interfaces CM-08 fieldbus interface ring (3xFO, xel.) GA0-8 / 6MF0AJ0AA0 AK 703 ACP TM 703 ACP BC 703 ACP AK 703 CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/SFBSA CM-860 patch plug standard V8,ET,TR CP-604 master control element SM-55/SFBSA CM-860 patch plug standard V8,ET,TR CP-504 central processing SM-55/SFBSA CM-5860 patch module standard V8,ET CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) SM-55/SFBSA CM-860 patch plug standard V8,ET,TR BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 BC5-04 / 6MF030FA40AA0 BC-55 / 6MF030CF50AA0 CC5-860 / 6MF30FJ600AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 BC-55 / 6MF030CF50AA0 CA-860 / 6MF0CJ600AA0 ACP 703 Platforms, Configuration AU Networks 63 DC0-0-.0, Edition 07.0

64 ESD EARTH FACILITY PS X X3 TB X6 NC X7 M-PRE/0 SIM0 X8 M-PRE/ SI (ETO) X9 M-PRE/ SI (FB) X 0 M-PRE/3 X4 FB X X x RX TX LOC SI /LK /PK SI WD /LK /PK X5 X5 PWR 4-60VDC X X3 X PUS HTO REL EASE X3 TB X6 NC X7 M-PRE/0 SIM0 X8 M-PRE/ SI (E TO) ESD EARTH FACILITY X9 M-PRE/ SI (FB ) X0 M-PRE/3 X4 FB X X x RX TX LOC SI /LK /PK SI WD /LK /PK COMCPY X5 X , RES F PWR 4-60VDC 0 X PUS HTO REL EASE X3 0 F /- /-, F 0 F PS-56 0 ESD EARTH FACILITY PS-560 Configuration of Automation Networks..6 SIEMENS Fieldbus, IEC , optical, Tree IEC Master AK 703 ACP (redundancy possible) or TM 703 ACP Cable Patchcable, length max. 3 m Cable FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre Fieldbusinterfacs PS-663x, CM-08, CM-08 CM-087 Settings on the configurataion switches CM-08 Master-Module A 0-0 PUSHTO UNLOCK X 4 X6 Cable FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre Settings on the configurataion switch CM-08 -Module C Fieldbusinterfaces PS-663x, CM-08 Settings on the configurataion switch CM-08 Master-Module B CM-087 Fieldbusinterfaces PS-663x, CM-08 Cable FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre BC 703 ACP CM-087 s 0-0 X4 X6 AK 703 PUSHTO UNLOCK PUSH TO RELE ASE COMCPY RES PUSH TO RELE ASE FF OFF ON OFF TM 703 ACP BC 703 ACP AK 703 ACP 64 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

65 Configuration of Automation Networks Power supply of the fieldbus interfaces PS-663x (redundant power supply is supported, but not to increase power) via the electrical interface direct from the master, if only one fieldbus interface (CM-08) is used With one PS-663x max. 6 fieldbus interfaces CM-08 and/or CM-08 can be supplied. On the CM-087 (from version GA0-87-A on) line-idle state can be selected by a configuration switch Configuration switch CM-087 line-idle state light on line-idle state light off Redundant automation units (masters) are only possible in AK 703 ACP. A redundancy board rack CM-86 (SCA-RS) is necessary. Details you can find in the chapter Redundant Automation Units. CM-08 master-module A Configuration switch S... Rate 0... ON... )... Rate... ON... )... e.g. baudrate Rate... OFF... ) 4... Rate 3... ON... ) 5... Star/ring... OFF... star 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state Configuration switch S L... ON... ) master (single) R... ON... ) 0/... ON... Bit word length CM-08 master-module B... Rate 0... OFF... )... Rate... ON... )... e.g. baudrate , etc Rate... ON... ) 4... Master/slave. OFF... master 5... Level-CH4... OFF... line-idle state 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state CM-08 slave-module C... Rate 0... OFF... )... Rate... ON... )... e.g. baudrate , etc Rate... ON... ) 4... Master/slave. ON... slave 5... Level-CH4... OFF... line-idle state 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state ACP 703 Platforms, Configuration AU Networks 65 DC0-0-.0, Edition 07.0

66 Configuration of Automation Networks Necessary modules and cables Master AK 703 ACP electrical Master AK 703 ACP redundant optical Master TM 703 ACP Cable Cable length: length Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/SFBMA SM-556 SM-055/SFBMA CM-860 patch plug standard V8,ET,TR CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/SFBMA SM-556 SM-055/SFBMA CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-604 master control element SM-55/SFBMA SM-556 SM-055/SFBMA CM-860 patch plug standard V8,ET,TR Patch cable CAT5 (4x) AWG6/7 FO-INDOORCABLE-50-DUP-LSOH FO-OUTDOORCABLE-50-FIB-ARM FO-CONNECTOR-ST-50/6 FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CA-860 / 6MF0CJ600AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 TF7-07 TF7-08 TF7-06 TF7-006 TF7-007 TF7-06 Fieldbus interfaces CM-08 fieldbus interface ring (3xFO, xel.) GA0-8 / 6MF0AJ0AA0 CM-08 fieldbus interface star (4xFO) GA0-8 / 6MF0AJ0AA0 66 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

67 Configuration of Automation Networks AK 703 ACP TM 703 ACP BC 703 ACP AK 703 Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-55/SFBSA CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-604 master control element SM-55/SFBSA CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-504 central processing SM-55/SFBSA CM-586 patch plug SM-54 and CM-08/7 CM-087 fibre optical interface (electrical-fo) CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) SM-55/SFBSA CM-87 patch plug V8/opt. CM-08/7 CM-087 fibre optical interface (electrical-fo) Item Number / MLFB BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-55 / 6MF030CF50AA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 GC6-04 / 6MF30GA40AA0 BC-55 / 6MF030CF50AA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 BC5-04 / 6MF030FA40AA0 BC-55 / 6MF030CF50AA0 CC5-86 / 6MF30FJ60AA0 GA0-87 / 6MF0AJ70AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 BC-55 / 6MF030CF50AA0 CA-87 / 6MF0CJ70AA0 GA0-87 / 6MF0AJ70AA0 ACP 703 Platforms, Configuration AU Networks 67 DC0-0-.0, Edition 07.0

68 ESD EARTH FACILITY PS X P USH TO RELEASE X3 TB X6 NC X7 M-PRE /0 SIM0 X8 M-PRE / SI (ETO) 0 X9 M-PRE / SI (FB), X 0 M-PRE /3 F 0 X4 FB F /- /- X X x RX TX LOC SI /PK /LK SI /PK /LK COMCPY WD X5 X RES PWR X PUSHTO R ELE ASE X 3 0, F 0 F /- 0, F 0 F ESD EARTH FACILITY PS Configuration of Automation Networks. LAN Communication.. LAN Communication electrical Central Fibre Switch Switch distance > 0 m: with plenum cable via wall socket or patch panel Cable Patch cable, max. length 0 m Automation Units 0-0 TM 703 ACP P USH T OUNLOCK 4-60VDC X4 X 6 TM 703 emic TM 703 mic BC 703 ACP AK 703 ACP Cable Patchcable, length max. 3 m AK 703 Settings on the configuration switch CM-08 -Module B Fieldbusinterfaces PS-663x, CM-08, CM-08 ON OFF Cable FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre Settings on the configuration switches CM-08 Master-Module A FF Protective devices BC 703 ACP BC 703 ACP non-siemens protective device non-siemens protective device 68 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

69 Configuration of Automation Networks The electrical connection between Central Fibre Switch and SICAM 703 component can be up to 00 m. Hints for establishing an electrical connection of more than 0 m length you can find in the appendix. With one PS-663x max. 6 fieldbus interfaces CM-08 and/or CM-08 can be supplied. CM-08 master-module A Configuration switch S... Rate 0... OFF... )... Rate... ON... )... e.g. baudrate Rate... OFF... ) 4... Rate 3... ON... ) 5... Star/ring... OFF... star 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state Configuration switch S L... ON... ) master (single) R... ON... ) 0/... ON... Bit word length CM-08 slave-module B... Rate 0... ON... )... Rate... OFF... )... e.g. baudrate Rate... ON... ) 4... Master/slave. ON... slave 5... Level-CH4... OFF... line-idle state 6... Level-CH3... OFF... line-idle state 7... Level-CH... OFF... line-idle state 8... Level-CH... OFF... line-idle state ACP 703 Platforms, Configuration AU Networks 69 DC0-0-.0, Edition 07.0

70 Configuration of Automation Networks Necessary modules and cables Cable AK 703 ACP Designation Patch cable CAT5 (4x) AWG6/7 CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-556/ETA CM-860 patch plug standard V8,ET,TR Item Number / MLFB T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 T4-53 (5m) / 6MF3040BC530AA0 T4-54 (0m) / 6MF3040BC540AA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-556 / 6MF030CF560AA0 CA-860 / 6MF0CJ600AA0 TM 703 ACP CP-604 master control element GC6-04 / 6MF30GA40AA0 TM 703 emic SM-556/ETA CM-860 patch plug standard V8,ET,TR CP-600 emic Master Control Module ETT0 BC-556 / 6MF030CF560AA0 CA-860 / 6MF0CJ600AA0 GC6-00 / 6MF30GA00AA0 TM 703 mic CP-6040 mic MasterContr.ET0TX/V.8/8Mod GC6-040 / 6MF30GA400AA0 BC 703 ACP CP-504 central processing BC5-04 / 6MF030FA40AA0 AK 703 PROTECTIVE DEVICES Fieldbus interfaces Cable BC 703 ACP acc. to IEC local interface length: length: SM-556 SM-055 ET0 CM-5860 patch module standard V8,ET X 03MA0 CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) SM-556/ETA CM-860 patch plug standard V8,ET,TR CM-08 fieldbus interface ring (3xFO, xel.) CM-08 fieldbus interface star (4xFO) FO-INDOORCABLE-50-DUP-LSOH FO-OUTDOORCABLE-50-FIB-ARM FO-CONNECTOR-ST-50/6 FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 CP-504 central processing 03SX5 CPCX55 master data for 03SX5 local optical interface on CM-504 available X BC-556 / 6MF030CF560AA0 BC0-55 / 6MF030AF50AA0 CC5-860 / 6MF30FJ600AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 BC-556 / 6MF030CF560AA0 CA-860 / 6MF0CJ600AA0 GA0-8 / 6MF0AJ0AA0 GA0-8 / 6MF0AJ0AA0 TF7-07 TF7-08 TF7-06 TF7-006 TF7-007 TF7-06 BC5-04 / 6MF030FA40AA0 SC ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

71 ESD EARTH FACILITY PS-560 X PUSHT O RE LEASE X3 TB X6 NC X7 M -PR E/0 SIM 0 X8 M -PR E/ SI ( E T O) 0 X9 M -PR E/ SI (FB) X0 M -PR E/3, F 0 X4 FB F X X x RX TX LOC SI /LK /P K SI WD /LK /P K COMCPY X5 X RES PWR 4-60VDC X PUSHT O RE LEAS E X3 0, F 0 F /- /- /- ESD EARTH FA CILITY P S-560 0, F 0 F Configuration of Automation Networks.. LAN Communication optical Central Fibre Switch Cable FO, Fibre, length, plugs depend on the used switch type. Switch Cable FO, max. length: km using 50/5µm fibre km using 6,5/5µm fibre Local Switch Rail Switch BUS Rail Switch BUS Rail Switch BUS Rail Switch BUS Rail Switch BUS Cable 3 Patchcable, length max. 3 m Automation Units 0-0 TM 703 ACP PUSHTO UNLOCK X 4 X6 TM 703 emic TM 703 mic BC 703 ACP AK 703 ACP AK Settings on the configuration switch CM-08 -Module B Fieldbusinterfaces PS-663x, CM-08, CM-08 ON OFF Cable 4 FO, length: 0,5km using 50/5µm fibre,5km using 6,5/5µm fibre Settings on the configuration switches CM-08 Master-Module A 4 FF 4 Protective devices BC 703 ACP BC 703 ACP non-siemens protective device non-siemens protective device ACP 703 Platforms, Configuration AU Networks 7 DC0-0-.0, Edition 07.0

72 Configuration of Automation Networks With one PS-663x max. 6 fieldbus interfaces CM-08 and/or CM-08 can be supplied. CM-08 master-module A Configuration switch S... Rate 0... OFF...)... Rate... ON...)... e.g. baudrate Rate... OFF...) 4... Rate 3... ON...) 5... Star/ring... OFF...star 6... Level-CH3... OFF...line-idle state 7... Level-CH... OFF...line-idle state 8... Level-CH... OFF...line-idle state Configuration switch S L...ON...) master (single) R...ON...) 0/...ON... Bit word length CM-08 slave-module B... Rate 0... ON...)... Rate... OFF...)... e.g. baudrate Rate... ON...) 4... Master/slave. ON...slave 5... Level-CH4... OFF...line-idle state 6... Level-CH3... OFF...line-idle state 7... Level-CH... OFF...line-idle state 8... Level-CH... OFF...line-idle state 7 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

73 Configuration of Automation Networks Necessary modules and cables Cable Cable length: max. km Cable 3 AK 703 ACP Designation Fibre and length of cable and plugs depend on the specification of the used switches. Fibre 50/5 µm or 6,5 µm Ports on central fibre switch: individual Port on BC 703 ACP (SM-546): MT-RJ Patch cable CAT5 (4x) AWG6/7 CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-556/ETA CM-860 patch plug standard V8,ET,TR Item Number / MLFB T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-556 / 6MF030CF560AA0 CA-860 / 6MF0CJ600AA0 TM 703 ACP CP-604 master control element GC6-04 / 6MF30GA40AA0 TM 703 emic SM-556/ETA CM-860 patch plug standard V8,ET,TR CP-600 emic Master Control Module ETT0 BC-556 / 6MF030CF560AA0 CA-860 / 6MF0CJ600AA0 GC6-00 / 6MF30GA00AA0 TM 703 mic CP-6040 mic MasterContr.ET0TX/V.8/8Mod GC6-040 / 6MF30GA400AA0 BC 703 ACP CP-504 central processing BC5-04 / 6MF030FA40AA0 AK 703 PROTECTIVE DEVICES Fieldbus interfaces Cable 4 BC 703 ACP acc. to IEC local interface length: length: SM-546 SM-055 ETA CM-586 patch plug ET 00FX X 03MA0 CP-000 systemfunction CM-857 connection comm./sys-i/o (CP-000) CP-00 systemfunction, processing and CM-858 connection (CP-00) SM-556/ETA CM-860 patch plug standard V8,ET,TR CM-08 fieldbus interface ring (3xFO, xel.) CM-08 fieldbus interface star (4xFO) FO-INDOORCABLE-50-DUP-LSOH FO-OUTDOORCABLE-50-FIB-ARM FO-CONNECTOR-ST-50/6 FO-INDOORCABLE-6-DUP-LSOH FO-OUTDOORCABLE-6-FIB-ARM FO-CONNECTOR-ST-50/6 CP-504 central processing 03SX5 CPCX55 master data for 03SX5 local optical interface on CM-504 available X BC-546 / 6MF030CF460AA0 BC0-55 / 6MF030AF50AA0 CC5-86 / 6MF30FJ60AA0 BA-000 / 6MF00CA000AA0 BA-857 / 6MF00CJ570AA0 BA-00 / 6MF00CA00AA0 BA-858 / 6MF00CJ580AA0 BC-556 / 6MF030CF560AA0 CA-860 / 6MF0CJ600AA0 GA0-8 / 6MF0AJ0AA0 GA0-8 TF7-07 TF7-08 TF7-06 TF7-006 TF7-007 TF7-06 BC5-04 / 6MF030FA40AA0 SC5-598 ACP 703 Platforms, Configuration AU Networks 73 DC0-0-.0, Edition 07.0

74 ESD EAR TH FACILITY X X PS -560 Configuration of Automation Networks.3 Fieldbus/Profibus Communication.3. Fieldbus/Profibus Communication: Master AK 703 ACP Master AK 703 ACP Cable Patchcable Connectionbox CM-845 CM-845 Fieldbuscable Profibus DP s Necessary modules and cables Master AK 703 ACP Cable Fieldbus cable Designation CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-545/DPM00 CM-869 patch plug CM-845 connection box for SM-545 in AK Patch cable CAT5 (4x) AWG6/7 Siemens 6XV830-0EH0 for indoor laying Siemens 6XV830-3FH0 for underground laying Item Number BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BA-545 / 6MF00CF450AA0 CA-869 / 6MFCJ600AA0 GA-845 / 6MF0CJ450AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 T4-53 (5m) / 6MF3040BC530AA0 T4-54 (0m) / 6MF3040BC540AA0 74 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

75 PUSH TO RELEASE X X3 TB X6 NC X7 M-P RE /0 SIM0 X8 M-P RE / SI ( ETO) X9 M-P RE / SI ( FB ) X0 M-P RE /3 X4 FB X X LO C SI /LK SI /LK RE S /PK WD /PK X5 X PWR X PUSHTO REL EASE X3 Configuration of Automation Networks.3. Fieldbus/Profibus Communication: Master TM 703 ACP Master TM 703 ACP 0-0 x RX TX COMCPY X4 X6 P US H TO UNLO CK 4-60V DC Fieldbuscable Profibus DP s The fieldbus can be plugged on the DSubsocket X4 FB or on the RJ-45 socket X9/SI on the master control element. Necessary modules and cables Master TM 703 ACP Fieldbus cable Designation CP-604 master control element SM-545/DPM00 CM-869 patch plug Siemens 6XV830-0EH0 for indoor laying Siemens 6XV830-3FH0 for underground laying Item Number / MLFB GC6-04 / 6MF30GA40AA0 BA-545 / 6MF00CF450AA0 CA-869 / 6MFCJ600AA0 ACP 703 Platforms, Configuration AU Networks 75 DC0-0-.0, Edition 07.0

76 Configuration of Automation Networks 76 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

77 3 Redundancy Content 3. Redundant Basic System Elements Redundant Automation Units...87 ACP 703 Platforms, Configuration AU Networks 77 DC0-0-.0, Edition 07.0

78 ESD EARTH FACILITY ESD EARTH FACILITY PS-560 PS-560 Redundancy 3. Redundant Basic System Elements 3.. AK 703 ACP AK 703 ACP PE, electrical, redundant BSE Base unit AK 703 ACP to peripheral elements AK 703 ACP, electrically connected, redundant basic system elements Basiseinheit AK 703 ACP Ax 703 Peripheriebus (elektrisch) 6 MBit/s Patch-Kabel, bis 3 m Länge CP-07 CP-00 Peripherieelemente AK 703 ACP (max. 6 PE) Rückansicht CM-833 Line Line To one basic system element CP-07/PCCX5 one bus line with max. 6 peripheral elements can be connected. The slots for the redundant BSE-pairs are predefined, in fact:, 45, 78, (0, 34 only in 7 slots mounting rack). If peripheral elements are equipped in the base unit AK 703 ACP then those can be driven either by the singular BSE CP-00 or by the redundant BSEs CP-07. Depending on the slots of the basic system elements the socket connectors for the electrical Ax 703 peripheral bus have to be selected. (for example: slots C4 and C5 socket connectors AXPE-C4 and AXPE-C5) Redundant BSEs have to have identic configuration and identic functionality. 78 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

79 Redundancy Necessary modules and cables Base unit AK 703 ACP Cable Peripheral elements AK 703 ACP Designation CP-07 Processing and element CP-07/PCCX5 Patch cable CAT5 (4x) AWG6/7 CM-833 AK 703 ACP board rack extension Item Number / MLFB BC-07 / 6MF030CA70AA0 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 GC-833 / 6MF30CJ330AA0 ACP 703 Platforms, Configuration AU Networks 79 DC0-0-.0, Edition 07.0

80 ESD EART H FACILIT Y PS-560 Redundancy 3.. AK 703 ACP TM 703 ACP PE, electrical, redundant BSE Base unit AK 703 ACP to peripheral elements TM 703 ACP, electrically connected, redundant basic system elements Basiseinheit AK 703 ACP Ax 703 Peripheriebus (elektrisch) 6 MBit/s Patch-Kabel, bis 3 m Länge Bus Interface Module CM-0843 (max. 4) CP-07 CP-00 PS-663x PE-640 I/O Module (max. 8) Peripherieelemente TM 703 ACP (max. 6 PE) Ax 703 Peripheriebus (elektrisch) 6 MBit/s USB-Kabel, bis 3 m Länge Peripherieelement To one basic system element CP-07/PCCX5 one bus line with max. 6 peripheral elements can be connected. The slots for the redundant BSE-pairs are predefined, in fact:, 45, 78, (0, 34 only in 7 slots mounting rack). Redundant BSEs have to have identic configuration and identic functionality. If peripheral elements are equipped in the base unit AK 703 ACP then those can be driven either by the singular BSE CP-00 or by the redundant BSEs CP-07. Depending on the slots of the basic system elements the socket connectors for the electrical Ax 703 peripheral bus have to be selected. (for example: slots C4 and C5 socket connectors AXPE-C4 and AXPE-C5) The bus interface modules CM-0843 are supplied by the power supplies PS-663x. The power consumption of the CM-0843 (see technical data in data sheet) has to be considered on the PS-663x. 80 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

81 Redundancy Necessary modules and cables Base unit AK 703 ACP Designation CP-07 Processing and element CP-07/PCCX5 Item Number / MLFB BC-07 / 6MF030CA70AA0 Cable Patch cable CAT5 (4x) AWG6/7 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Bus Interface Modules CM-0843 Ax 703-bus interface electrical GA0-843 / 6MF0AJ430AA0 Cable USB-cable TC6-0 (,5m) / 6MF330GC00AA0 TC6-0 (m) / 6MF330GC00AA0 TC6-03 (3m) / 6MF330GC030AA0 Peripheral elements TM 703 ACP PE-640 peripheral coupling Ax-bus electrical GC6-40 / 6MF30GE00AA0 ACP 703 Platforms, Configuration AU Networks 8 DC0-0-.0, Edition 07.0

82 ESD EARTH FACILITY PS BSE CM-0843 BSE Redundancy 3..3 AK 703 ACP TM 703 ACP PE, electrical and optical, redundant BSE Base unit AK 703 ACP to peripheral elements TM 703 ACP, electrically and optically connected, redundant basic system elements Basiseinheit AK 703 ACP Ax 703 Peripheriebus (elektrisch) 6 MBit/s Patch-Kabel, bis 3 m Länge Bus Interface Module CM-084 Bus interface Module CM-0843 X4 BSE X5 LINE X6 RED Tx : ON S OFF CP-07 CP-00 3 PS-663x PE-640 Ax 703 Peripheriebus (elektrisch) 6 MBit/s USB-Kabel, bis 3 m Länge I/O Module (max. 8) Ax 703 Peripheriebus (optisch) 6 MBit/s LWL, bis 00 m Länge PS-663x PE-64 I/O Module (max. 8) Peripherieelement Peripherieelement Peripherieelemente TM 703 ACP (max. 6 PE) To one basic system element CP-07/PCCX5 one bus line with max. 6 peripheral elements can be connected. The slots for the redundant BSE-pairs are predefined, in fact:, 45, 78, (0, 34 only in 7 slots mounting rack). Depending on the slots of the basic system elements the socket connectors for the electrical Ax 703 peripheral bus have to be selected. (for example: slots C4 and C5 socket connectors AXPE-C4 and AXPE-C5) The bus interface modules CM-0843 are supplied by the power supplies PS-663x. The power consumption of the CM-0843 (see technical data in data sheet) has to be considered on the PS-663x. In configurations with optical remoted TM 703 ACP PEs 000µm-fibre cables cannot be used! Redundant BSEs have to have identic configuration and identic functionality. Each bus interface module CM-084 has to be supplied seperately. (8 VDC VDC) Configuration switch CM F/F...ON...6 MBit...LINE...OFF...PE(O) 3...AS...OFF AS...OFF AS0...OFF RED...ON...BSE 7...LAD...OFF...inactive 8...LINE...ON...: 8 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

83 Redundancy Necessary modules and cables Base unit AK 703 ACP Designation CP-07 Processing and element CP-07/PCCX5 Item Number / MLFB BC-07 / 6MF030CA70AA0 Cable Patch cable CAT5 (4x) AWG6/7 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Bus interface modules CM-0843 Ax 703-bus interface electrical CM-084 Ax 703-bus interface 4x FO GA0-843 / 6MF0AJ430AA0 GA0-84 / 6MF0AJ40AA0 Cable USB-cable TC6-0 (,5m) / 6MF330GC00AA0 TC6-0 (m) / 6MF330GC00AA0 TC6-03 (3m) / 6MF330GC030AA0 Cable 3 FO-INDOORCABLE-00-DUP-BREAK-ROUND FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-OUTDOORCABLE-00-FIB-ARM FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-PIPE SPLITT Y-LR ( pcs. per connection) (only for outdoorcabletf7-036) TF7-035 TF7-05 TF7-036 TF7-05 TF7-066 Peripheral elements TM 703 ACP PE-640 peripheral coupling Ax-bus electrical GC6-40 / 6MF30GE00AA0 PE-64 peripheral coupling Ax-bus x optical GC6-4 / 6MF30GE0AA0 ACP 703 Platforms, Configuration AU Networks 83 DC0-0-.0, Edition 07.0

84 ESD EARTH FACI LI TY PS Redundancy 3..4 AK 703 ACP TM 703 ACP PE, optical, redundant BSEredundant Ax-PE-Bus Base unit AK 703 ACP to peripheral elements TM 703 ACP, optically connected, redundant basic system elements and redundant Ax-PE-Bus Basiseinheit AK 703 ACP Ax 703 Peripheriebus (elektrisch) 6 MBit/s Patch-Kabel, bis 3 m Länge CP-07 CP-00 I/O Module (max. 8) Bus Interface Module CM-084 ON S OFF ON S OFF Ax 703 Peripheriebus (optisch) 6 MBit/s LWL, bis 00 m Länge PS-663x PE-64 I/O Module (max. 8) Peripherieelemente TM 703 ACP (max. 6 PE) Peripherieelement To one basic system element CP-07/PCCX5 one bus line with max. 6 peripheral elements can be connected. The slots for the redundant BSE-pairs are predefined, in fact:, 45, 78, (0, 34 only in 7 slots mounting rack). Depending on the slots of the basic system elements the socket connectors for the electrical Ax 703 peripheral bus have to be selected. (for example: slots C and C socket connectors AXPE-C and AXPE-C) In configurations with optical remoted TM 703 ACP PEs 000µm-fibre cables cannot be used! Redundant BSEs have to have identic configuration and identic functionality. Each bus interface module CM-084 has to be supplied seperately. (8 VDC VDC) Attention: Break of an FO-connection leads to a failure of the peripheral elements PE-64 until the redundant basic system element duly assumes the function. During this time connection to the peripheral elements PE-64 doesn t exist. Configuration switch CM F/F...ON...6 MBit...LINE...OFF...PE(O) 3...AS...OFF AS...OFF AS0...OFF RED...OFF...CM LAD...OFF...inactive 8...LINE...ON...PE 84 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

85 Redundancy Necessary modules and cables Base unit AK 703 ACP Designation CP-07 Processing and element CP-07/PCCX5 Item Number / MLFB BC-07 / 6MF030CA70AA0 Cable Patch cable CAT5 (4x) AWG6/7 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 Bus interface modules Cable Peripheral elements TM 703 ACP CM-084 Ax 703-bus interface 4x FO FO-INDOORCABLE-00-DUP-BREAK-ROUND FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-OUTDOORCABLE-00-FIB-ARM FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-PIPE SPLITT Y-LR ( pcs. per connection) (only for outdoorcabletf7-036) PE-64 peripheral coupling Ax-bus x optical GA0-84 / 6MF0AJ40AA0 TF7-035 TF7-05 TF7-036 TF7-05 TF7-066 GC6-4 / 6MF30GE0AA0 ACP 703 Platforms, Configuration AU Networks 85 DC0-0-.0, Edition 07.0

86 ESD EARTH FACILITY PS- 560 Redundancy 3..5 Data Transfer between redundant BSE-Pairs IEC Central Fiber Switch Switch Switch Switch Kabel Patchkabel, max. Länge 0 m Plenumkabel, max. Länge 90 m AK 703 ACP CP-07 CP-00 Data exchange between the redundant BSEpairs is carried out only external via Ethernet. On each CP-07 a SM-556 has to be equipped. The slots for the redundant BSE-pairs are predefined, in fact:, 45, 78, (0, 34 only in 7 slots mounting rack). The electrical connection between Central Fibre Switch and SICAM 703 component can be up to 00 m. Depending on the slots of the basic system elements the socket connectors for the electrical Ax 703 peripheral bus have to be selected. (for example: slots C and C socket connectors AXPE-C and AXPE-C) Power supply has to be redundant! Redundant BSEs have to have identic configuration and identic functionality. Hints for establishing an electrical connection of more than 0 m length you can find in the appendix. Necessary modules and cables Base unit AK 703 ACP Designation CP-07 processing and Processing and element CP-07/PCCX5 CM-838 connection (CP-07) SM-556/ETA CM-860 patch plug standard V8,ET,TR Item Number / MLFB BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-556 / 6MF030CF560AA0 CA-860 / 6MF0CJ600AA0 Cable Patch cable CAT5 (4x) AWG6/7 T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 T4-53 (5m) / 6MF3040BC530AA0 T4-54 (0m) / 6MF3040BC540AA0 86 ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

87 ESD EA RTH FA CILITY PS -560 P S-560 PS -560 ESD EARTH FA CILITY PS -560 Redundancy 3. Redundant Automation Units 3.. Redundant AUs, Voting by SCA-RS, Distance up to 5 m SCA-RS Voter SCA-RS SCA-RS Cable CM-80 TB cable length 5 m Ethernet IEC Cable Patch cable Cable 3 High speed link FO, max. length 00 m 3 Automation unit AK 703 ACP redundancy syncrhonization via High Speed Link to the remote peripheral elements to the slaves see the chapters Redundant Basic System Elements and Redundant AUs in ring configurations and Redundant AUs in star configurations Redundancy synchronization of function diagram and of the peripheriy is executed by a high speed link. A high speed link is essential with singular periphery. The electrical connection between Ethernet and SICAM 703 component can be up to 00 m. Hints for establishing an electrical connection of more than 0 m length you can find in the appendix. Depending on the slots of the basic system elements the socket connector for the H.S.L. connection has to be selected. (e.g. slot C0 socket connector HSL-C0) The following socket connectors are available: HSL-C0 and C, in the small rack CM-83 and additional C4, C7, C0, C3 in the large rack CM-835 SCA-RS is connected to AK 703 ACP via the socket connector SYS-IO on the AK 703 ACP. ACP 703 Platforms, Configuration AU Networks 87 DC0-0-.0, Edition 07.0

88 Redundancy Necessary modules and cables Designation SCA-RS Voter CM-86 redundancy board rack for AK 703 SCA-RS redundancy switch E-prom RED5 AK 703 ACP CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-556/ETA CM-860 patch plug standard V8,ET,TR CM-088 fibre-optic-interface (TTL-LWL) pcs. for SCA-RS connection pcs. for high speed link Item Number / MLFB GA-86 / 6MF0CJ60AA0 B70-00 / 6MF0070AA00AA0 SC-05 / 6MF430CA50AA BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-556 / 6MF030CF560AA0 CA-860 / 6MF0CJ600AA0 GA0-88 / 6MF0AJ80AA0 Cable CM-80 TB cable BA-80 / 6MF00BJ00AA0 Cable Cable 3 Patch cable CAT5 (4x) AWG6/7 FO-INDOORCABLE-00-DUP-BREAK-ROUND FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-OUTDOORCABLE-00-FIB-ARM FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-PIPE SPLITT Y-LR ( pcs. per connection) (only for outdoorcabletf7-036) T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 T4-53 (5m) / 6MF3040BC530AA0 T4-54 (0m) / 6MF3040BC540AA0 TF7-035 TF7-05 TF7-036 TF7-05 TF ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

89 ESD E ARTH FACILITY PS-560 P S-560 PS-560 HSA 50S4- P LANTRONICS HSA 50S4- P ESD EA RTH FA CILITY LANTRONICS PS -560 Redundancy 3.. Redundant AUs, Voting by SCA-RS, Distance up to 00 m Modular-coupling RJ-45-9-pin D-SUB female back view CM-86 CM-80 TB cable SCA-RS Voter SCA -RS SCA -RS Cable CM-80 TB cable length 5 m Modular-coupling RJ-45-9-pin D-SUB female with patch cable Lantronix-Server with power supply Modular-coupling RJ-45-9-pin D-SUB male Ethernet Cable Patch cable IEC Cable 3 High speed link FO, max. length 00 m 3 Automation unit AK 703 ACP redundancy syncrhonization via High Speed Link to the remote peripheral elements to the slaves see the chapters Redundant Basic System Elements and Redundant AUs in ring configurations and Redundant AUs in star configurations Redundancy synchronization of function diagram and of the peripheriy is executed by a high speed link. A high speed link is essential with singular periphery. SCA-RS is connected to AK 703 ACP via the socket connector SYS-IO on the AK 703 ACP. The electrical connection between Ethernet and SICAM 703 component or between Ethernet and Lantronix-Server can be up to 00 m. Depending on the slots of the basic system elements the socket connector for the H.S.L. connection has to be selected. (e.g. slot C0 socket connector HSL-C0) The following socket connectors are available: HSL-C0 and C, in the small rack CM-83 and additional C4, C7, C0, C3 in the large rack CM-835 The LANTRONIX Server can be supplied by the Power Supply HSA 50S4-P from MTM Power. SIEMENS item number: MTMHSA50S4-P Hints for establishing an electrical connection of more than 0 m length you can find in the appendix. ACP 703 Platforms, Configuration AU Networks 89 DC0-0-.0, Edition 07.0

90 Redundancy Necessary modules and cables Designation SCA-RS Voter CM-86 redundancy board rack for AK 703 SCA-RS redundancy switch E-prom RED5 AK 703 ACP connected by LANTRONIX-server CP-00 systemfunction, processing and CM-837 connect comm./sys-i/o (CP-00) CP-07 processing and CM-838 connection (CP-07) SM-556/ETA CM-860 patch plug standard V8,ET,TR CM-088 fibre-optic-interface (TTL-LWL) pcs. for SCA-RS connection pcs. for high speed link LANTRONIX Server XPress DR-IAP Technical details and ordering information can be found here: Modular coupling RJ-45 9-pol. D-SUB male Modular coupling RJ-45 9-pol. D-SUB female Item Number / MLFB GA-86 / 6MF0CJ60AA0 B70-00 / 6MF0070AA00AA0 SC-05 / 6MF430CA50AA BC-00 / 6MF030CA00AA0 BC-837 / 6MF030CJ370AA0 BC-07 / 6MF030CA70AA0 BC-838 / 6MF030CJ380AA0 BC-556 / 6MF030CF560AA0 CA-860 / 6MF0CJ600AA0 GA0-88 / 6MF0AJ80AA0 TF5-00 / 6MF340FB000AA0 TF5-0 / 6MF340FB00AA0 Cable CM-80 TB cable BA-80 / 6MF00BJ00AA0 Cable Cable 3 Patch cable CAT5 (4x) AWG6/7 FO-INDOORCABLE-00-DUP-BREAK-ROUND FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-OUTDOORCABLE-00-FIB-ARM FO-CONNECTOR-ODLP-00 ( pcs. per connection) FO-PIPE SPLITT Y-LR ( pcs. per connection) (only for outdoorcabletf7-036) T4-55 (m) / 6MF3040BC550AA0 T4-5 (m) / 6MF3040BC50AA0 T4-5 (3m) / 6MF3040BC50AA0 T4-53 (5m) / 6MF3040BC530AA0 T4-54 (0m) / 6MF3040BC540AA0 TF7-035 TF7-05 TF7-036 TF7-05 TF ACP 703 Platforms, Configuration AU Networks Edition 07.0, DC0-0-.0

91 ESD E ARTH FACILITY PS-560 P S-560 PS-560 HSA 50S4-P LANTRONICS HSA 50S4-P ESD EARTH FACILITY LANTRONICS PS-560 Redundancy 3..3 Redundant AUs, Voting by SCA-RS, Distance higher than 00 m Modular-coupling RJ-45-9-pin D-SUB female back view CM-86 CM-80 TB cable SCA-RS Voter SCA-RS SCA-RS Cable CM-80 TB cable length 5 m Modular-coupling RJ-45-9-pin D-SUB female with patch cable Lantronix-Server with power supply Modular-coupling RJ-45-9-pin D-SUB male Ethernet IEC Cable Patch cable redundancy syncrhonization preferred via Ethernet Automation unit AK 703 ACP to the remote peripheral elements to the slaves see the chapters Redundant Basic System Elements and Redundant AUs in ring configurations and Redundant AUs in star configurations SCA-RS is connected to AK 703 ACP via the socket connector SYS-IO on the AK 703 ACP. Redundancy synchronization of functional diagrams and periphery is carried out via free selectable (Ethernet preferred, select transfer as fast as possible). A seperate interface is recommended. The electrical connection between Ethernet and SICAM 703 component or between Ethernet and Lantronix-Server can be up to 00 m. The protocol element for redundancy synchronization must not be placed on the M-CPU but should be necessarily situated on the synchronized C-CPUs. In this configuration only redundant periphery is possible. ATTENTION: Time-critical applications aren t possible in the FUD. Minimal cycle time: ms The LANTRONIX Server can be supplied by the Power Supply HSA 50S4-P from MTM Power. SIEMENS item number: MTMHSA50S4-P Hints for establishing an electrical connection of more than 0 m length you can find in the appendix. ACP 703 Platforms, Configuration AU Networks 9 DC0-0-.0, Edition 07.0