Capacitive sensors s26

Transcription

1 Capacitive sensors s26

2 Registration No.: For all transactions, the latest version of the General Conditions of Sale and Delivery for Products and Services of the Electrical Industry ZVEI shall apply, along with the supplementary conditions extended reservation of proprietary rights, together with the supplements listed on our order confirmations and/or invoices. All specifications are subject to change without notice. Reprint, even in part, only with our consent. RECHNER Germany 04/2017 GB - Printed in EU, all rights reserved. Edition April 2017 With publication of this catalogue all former printed catalogues about RECHNER KAS series capacitive sensors are invalid. All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

3 CAPACITIVE SENSORS KAS S26 Pages Technology 4-6 Adjustment 7 Typical curves 8 Mounting 9-10 Technical Terms Series Type code Product description S Capacitive sensors S Capacitive sensors S26, ATEX Capacitive sensors S26, LevelMaster Type selection in article number order 117 All specifications are subject to change without notice. (04/2017 Type selection in article description order 118 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 3

4 TECHNOLOGY Capacitive sensors, our abbreviation KAS, contain a transistor oscillator which is actuated when a defined capacitance is exceeded by the approach of metals, non-metals or liquids. The smaller its dielectric permittivity ε r the closer the medium has to be approached. This effect can also be achieved by detecting through non-metal materials, if the dielectric permittivity of the material to be detected is higher (approx. factor 5. Depending on the type the current change of the oscillator will be amplified to a streamlined output signal or output as a binary signal by a switching amplifier. Output stages with npn or pnp transistors are available for DC operation. A transistor output stage or FET-output is integrated for AC connection The output switching functions are similar to mechanical switches Normally open NO Normally closednc Change-over ( (NO + NC Electronic circuits, PLCs, relays or contactors can be activated directly by capacitive sensors. The current change in the oscillator is caused without physical contact by the approach of the actuating material to the active area. The damping of the oscillator is possible between the active surface and specified sensing distance (Sn ± 10 %. The RECHNER capacitive sensors with 20-turn spindle potentiometer allow sensitivity adjustment greater or less than the nominal sensing distance. Under the best operating conditions (e.g. constant ambient conditions a sensing distance up to the maximum specified value can be adjusted. The components of the KAS are mounted in plastic or metal casings and encapsulated with epoxy casting resin. By means of the following measures all devices are insensitive to dirt, vibration (vibration stability: 30 g, Hz, 1 hour and are watertight (depending on the type, up to IP 68. The choice of housings enables a wide range of applications, e.g. with aggressive media, in hot areas or in areas subjected to steam. Only pre-tested electronic components, proven integrated circuits and hybrid circuits are used and produced with SMT. The standard constant ambient temperature permitted is -25 up to +70 C, and up to 90 C for brief periods. High-temperature types for use from -200 up to +250 C are also included in our general product line. With contactless detection no physical actuating force is required for operation. There is no contact bounce, no sensor wear, no maintenance and the service life is independent of the switching frequency. KAS can be used in machines, systems and vehicles for level monitoring of liquids or bulk material, and also through non-metal windows. Further more as limit switches, contact-less position switches for monitoring and positioning, as pulse generator for counting tasks, distance and speed measurements and for many other applications. All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

5 TECHNOLOGY Housing materials The application of the housing materials used is based on the technical specifications of the material and of the manufacturer. Even though RECHNER Sensors have far-reaching application experience concer ning the use of different housing materials, the customer is responsible for checking in each case that the housing material is suitable for the application. The following housing materials are used: Short description Material FDA - No. Contact with food permitted Traceability according to. EU 1935/2004 All specifications are subject to change without notice. (04/2017 PA Polyamide 6.6, glasfibre reinforced No No No PC Polycarbonate FDA 21 CFR No PEEK Polyetheretherketone FDA 21 CFR POM Polyoxymethylene No No No PP Polypropylene FDA 21 CFR No PPO Polyphenylenoxide No No No Polytetrafluorethylene FDA 21 CFR PVC Polyvinylchloride No No No PVDF Polyvinylidenfluoride FDA 21 CFR No AL Aluminium No No No MS Brass / chrome or nickel plated No No No VAa Stainless steel VA, material No (AISI 304 No No No VAb Stainless steel VA, material No (AISI 303 No No No VAc Stainless steel VA, material No (AISI 316L FDA No Wiring of the capacitive sensors should be routed separately or screened from heavy conductor lines, as in extreme cases inductive peak voltages can destroy the sensors despite the integrated protective circuit. Screened cable or twisted lines are recommended, especially for longer cable runs > 5 m. Direct control of electric light bulbs is to be avoided, because during the switch-on moment cold current is many times the rated current and can destroy the output stage of the sensor. Units with strong near field power, e. g. high power walkie-talkies, or noise sources in the lower frequency range, e.g. long, middle or short wave transmitters should not be operated close to the sensors or additional measures have to be taken in order to eliminate incorrect operation. RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 5

6 TECHNOLOGY Series connection or parallel connection 2- and 3-wire sensors with binary output can be used in series or parallel connection, similar to mechanical contacts. The type-typical voltage drop and the residual voltage U d, which must be multiplied in accordance with the number of sensors for series connection, must be noted. In the case of parallel connection of sensors with thyristor output, the first switched output takes over the total load current. Series connection Parallel connection 2 wire AC / DC 3 wire DC NPN 3 wire DC PNP All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

7 ADJUSTMENT Capacitive sensors with analogoutput ma/ V or inverted Analog capacitive sensors are equipped with a 20-turn spindle potentiometer. This allows adjustment of an application specific operating range between the minimum distance 0 mm and the type-typical maximum value. Consequently, the full output current range (4 20 ma is always present, regardless of the required measuring distance. The analog sensors of series 80 are designed with a 2-colour LED which facilitates adjustment. Within the operating range of 4 20 ma the LED is yellow. In the undamped state the output current value is > 20 ma and moves with the reduction of the object distance toward 4 ma (value at total damping approx. 2.5 ma. In the case of series 40 for some types the current characteristic is inverselyproportional to the object-distance. Nominal sensing distance (Sn - measurement according to DIN VDE 0660, Part 208 The data of the nominal sensing distance are based on the measuring method according to DIN VDE 0660, Part 208. The respective nominal sensing distance is indicated with a tolerance of ± 10 %. The standard measurement plate is square with a thickness of 1 mm and is made of carbon steel FE 360 (defined in ISO 630: 1980 with a smoothed surface and earthed. The side lengths are equal to the diameter of the active area of the KAS or equal to 3 x Sn, depending on which value is greater. With a different material or a smaller surface of the actuating element, the sensing distance is smaller. Sensing distance Adjustment of the sensing distance is made by means of a spindle potentiometer with the screw driver provided. With pluggable sensors M 18 x 1 / Ø 22 the potentiometer is on the side. All specifications are subject to change without notice. (04/2017 Typ. response-time characteristic For size M 30 x 1.5 / Ø 30: First open plastic tab. For size > M 30 x 1.5 / Ø 30: First remove plastic sealing screw. The possible sensing distance for a particular material is dependent on the dielectric permittivity ε r and can be worked out by means of the typical reduction factors: Sensing distance = Sn x reduction factor. Material: FE 360 St 37 Water Wheat Wood Glass Oil PVC PE Ceramic Reduction factor approx RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 7

8 TYPICAL CURVES A = KAS-40-A13-IL, ATEX B = KAS-40-A24-IL-M30-V2A-StEx, ATEX Typ. curve of 2 wire analog sensors Parameter: Tu = 25 C, U B = 12 V DC Actuator Steel St 37, 1 mm thick, square, side length to 3 x diameter of the active area, earthed. C D E C = KAS-80-A13-IL D = KAS-80-A14-IL E = KAS IL(-M32 Parameter: Tu = 25 C, U B = 24 V DC Actuator Steel St 37, 1 mm thick, square, side length to 3 x diameter of the active area, earthed. Typ. curve of 3 wire analogue sensors wire analogue sensors with different adjustments KAS IL-M32-/Ms 1 = Adjustment 20 mm 2 = Adjustment 30 mm 3 = Adjustment 36 mm Parameter: Tu = 25 C, U B = 24 V DC Actuator Steel St 37, 1 mm thick, square, side length to 3 x diameter of the active area, earthed. All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

9 MOUNTING Flush mounting or non-flush mounting types There are two different types of capacitive sensors: For flush mounting in metal or other materials. These sensors can be mounted close together (see Fig. 1 and 3 and are specially designed for contact-less detection of solids or liquids through non-metal containers (max. wall-thickness 4 mm For non-flush mounting in metal or other materials. When mounting two or more sensors side by side a space / free zone must be provided (see Fig. 2 and 4. These sensors are designed for applications where the detecting material comes into contact with the active area of the sensor (e.g. level monitoring of bulk materials or liquids. Mounting Fig.1 Fig.2 FREE ZONE no damping material e Metal All specifications are subject to change without notice. (04/2017 Fig.3 The dimension e corresponds to the thread-free area of standard sensor types (-A21-. Otherwise e is 25 mm. Fig.4 For opposing active areas a 2,2 x Sn For non-flush mountable Sensors distance b has to be 1,5 x Sn. RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 9

10 MOUNTING Maximum Torgue In order to prevent damage to the threaded sleeves when mounting, the material and version-dependent maximum torque should be taken into consideration. The values listed in the table are based on the use of the nuts supplied with the sensors. Housing Material Thread PVC PPO PA 6.6 Brass Stainless Steel M 5 x Nm M 8 x Nm M 12 x Nm 1 Nm 1 Nm 0.2 Nm 15 Nm 15 Nm M 18 x 1-3 Nm 1.7 Nm 0.5 Nm 28 Nm 40 Nm M 22 x Nm 10 Nm 6 Nm 1,4 Nm 32 Nm 50 Nm M 30 x Nm 8 Nm 2.5 Nm 82 Nm 150 Nm M 32 x Nm 13 Nm 3 Nm 110 Nm 180 Nm G Nm - - Threaded sensors - maximum screw-in length Due to the permitted thread tolerances specified in German standard DIN 13, the maximum screw-in length for threaded sensors should be taken into consideration. Depending on that the length of the threaded block for screwing in proximity sensors should not exceed the following dimensions. In the case of larger threaded blocks we recommend drilling a blind hole in order to adhere to the maximum screw-in length. Thread: M 5 x 0.5 M 8 x 1 M 12 x 1 M 18 x 1 M 22 x 1.5 M 30 x 1.5 M 32 x 1.5 Maximum length 3 mm 6 mm 8 mm 12 mm 12 mm 12 mm 12 mm All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

11 TECHNICAL TERMS Unless otherwise specified technical data is as follows: +20 C, U B = 8 V DC for KAS-40; U B = 24 V DC for KAS-70 and KAS-80 and U B = 230 V AC for KAS-90. Operating sensing distance / S a Within the operating sensing distance the sensor operates reliably taking into account all the possible tolerances. It lies between 0 and 0.81 x S n. Power up time delay The time the sensor needs to be ready for operation after connecting the operating voltage. It is in the milliseconds range. Housing materials The application of the housing materials used is based on the technical specifications of the material and of the manufacturer. Even though RECHNER Sensors have far-reaching application experience concerning the use of different housing materials, the customer is responsible for checking in each case that the housing material is suitable for the application. Cable For the standard models PVC- or PUR-cable are used. One has to take into consideration that the cable should not be moved with ambient temperatures below 5 C. PVC is not suitable for use in applications with oil-based liquids or with UV-radiation. PUR is not suitable for continuous contact with water. For special application areas silicone or cables are available. Minimum sensing distance / S min The minimum possible sensing distance, which can be adjusted by potentiometer and which can be used effectively in practical applications with reference to a medium with ε r > 80. Maximum sensing distance / S max. The maximum possible sensing distance, which can be adjusted by potentiometer and which can be used effectively in practical applications with reference to a medium with ε r > 80. The sensors should only be used. under constant ambient conditions, such as constant temperature, no humidity, and no deposits on the active face of the sensor. Nominal sensing distance / S n The characteristic value of a proximity sensor, without consideration of production tolerances and variations due to temperature and voltages. All specifications are subject to change without notice. (04/2017 Real sensing distance / S r The sensing distance determined at +20 C and rated voltage. Here the series variance is taken into consideration. Variation max. 10 % + of S n. Reduction factors For materials other than metals (e.g. FE 360 or ST 37, Al, Cu or water, the reduction factors shown in the table on page 6 should be taken into consideration. Series- and parallel connection It is possible to connect the proximity sensors in series or parallel. When considering this it must be taken into account that the voltage drops are added for series connection and the residual voltages for parallel connection. Under these circumstances it is advisable to operate a maximum of three sensors in a corresponding circuit. Repeat accuracy of the switching point The variation of the switching point of two successive measurements at constant ambient conditions. Frequency of operating cycles The maximum damping and un-damping cycles of the proximity sensor within one second. To ascertain the frequency of operating cycles a pulse / break ratio of 1 : 2 is used as a basis, at S n. RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 11

12 TECHNICAL TERMS Switching hysteresis The difference between the switch-on and switch-off point of a proximity sensor, when approaching or moving away from the standard measuring plate. Temperature variation The displacement of the switching point if the ambient temperature changes. Degree of protection according to IEC Digit: Protection against solids 2. Digit: Protection against water IP 0 No protection 0 No protection against water IP 1 Protection against solid foreign bodies Ø > 50 mm IP 2 Protection against solid foreign bodies Ø > 12,5 mm IP 3 Protection against solid foreign bodies Ø > 2,5 mm IP 4 Protection against solid foreign bodies Ø > 1 mm IP 5 Protection against harmful dust deposits, dust protected IP 6 Protection against contact with voltage-carrying parts. Protection against penetration of dust 1 Protection against vertical water drops 2 Protection against diagonal water drops (up to a 15 angle 3 Protection against spray water 4 Protection against splashing water 5 Protection against water jet 6 Protection against strong water jet 7 Protection against ingress of water when the equipment is immersed in water, up to 1 m depths and for a period of 30 minutes 8 Protection against ingress of water when the equipment is immersed in water, under conditions determined from the manufacturer. 9 Protection against ingress of water during high pressure or steam cleaning under defined conditions All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

13 SERIES Capacitive sensors - series 40 The series 40 contains capacitive 2-wire proximity signal generators according to NAMUR DIN , also StEx-Versions for use in zone 20 (dust explosion protection. These sensors can be mounted in explosion hazardous areas when they are connected to approved isolating switching amplifiers with intrinsically safe control circuit [EExia] or [EExib], our series N-132. Depending on the isolating switching amplifier selected the NAMUR-sensors of this series can be used up to zone 0 (StEx-Versions also for zone 20. The data specified in the certificate of ity of the selected isolating switching amplifier must be taken into consideration. The 2-wire analog sensors of this series can also be used in zone 0 if they are connected to an ATEX-certificated amplifier, such as our series N-132. Transistor amplifier - series 120 The transistor amplifier of our series 120 has been designed especially for use with our capacitive NAMUR mini-sensors (e.g. KAS-40-6/15-N, KAS-40-A11-N, KAS-40-18/5-N. All sensors according to NAMUR are connectable (provided that the cable diameter corresponds to the connector, our series IAS- 30 and KAS-40 The sensing distance is adjustable by means of a potentiometer, this also applies to capacitive sensors that have no adjustment on the body. The antivalent outputs (NO and NC function are overload protected and are available as pnp or npn output. The strong PA 6.6 housing may be mounted with additional units side by side and is equipped with a two- colour LED display that monitors stand-by (green operating condition (yellow. Sensor and amplifier may be connected by a plug contact (female connector is enclosed. Capacitive sensors - series 70 The series 70 contains capacitive 3-wire or 4-wire proximity sensors with NPN digital output with NO, NC or antivalent function (NO and NC. Electronic circuits, PLC s, relays and our power supplies of series 130 can be activated directly. The sensors are reverse-polarity protected, overload-protected and have electronic short-circuit protection. StEx-versions with ATEX and IECEx certification for applications in zone 20, sensors for ambient temperatures up to +100 C or for products with very high static charge complete the scope of the standard versions. Capacitive sensors - series 80 All specifications are subject to change without notice. (04/2017 The series 80 contains capacitive 3-wire or 4-wire proximity sensors with PNP digital output with NO, NC or antivalent function (NO and NC. Electronic circuits, PLC s, relays and our power supplies of series 130 can be activated directly. The sensors are reverse-polarity protected, overload-protected and have electronic short-circuit protection. StEx-versions with ATEX and IECEx certification for applications in zone 20, sensors for ambient temperatures up to +100 C or for products with very high static charge complete the scope of the standard versions. Capacitive sensors - series 2000 The series 2000 quattro+ 3 contains capacitive 3-wire DC proximity sensors with four output-functions, NPN-NO and PNP-NC or, after resetting of the coding switch, NPN-NC and PNP-NO. Electronic circuits, PLC s and relays can be directly activated. Different housing materials are available, such as PA or PPO,, / brass or / VA. This series is completed by a version for medium temperatures up to +160 C. RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 13

14 SERIES Capacitive sensors - series 90 The series 90 contains capacitive 2-wire AC / DC proximity sensors with thyristor digital output or FETstage with NO and NC function. AC relays, conductors and solenoid valves can be directly activated. PLCs with AC inputs can also be connected so long as the minimum load current is taken into consideration. The sensors have a protective circuit against high induction voltages. Capacitive sensors - series 1000 The series 1000 duo~ 2 contains capacitive 2-wire a.c.-d.c. proximity sensors with NO and NC-function. The supply voltage range of V AC / DC allows for applications in electronic circuits, PLC s as well as for conductors with AC supply voltage. The output functions (NO or NC can be determined by means of a coding switch. Increased requirements to the sensor For increased requirements for the permitted ambient temperature range of our capacitive proximity sensors, we offer the series up to +100 C with integrated electronics as a 3-Wire DC version (see series 70 and 80. The sensors are available with housings made of, / VA or / brass. Sensors with quattro+ 3 are available for temperatures up to +160 C (medium (see series Here too housing materials of and VA are used as standard. For extreme ambient or product-temperature conditions, our series 250 (see series 250 or KXS-Extreme are available with high temperature sensors up to +250 C and remote electronics (please ask for the KXS catalogue. The sensors of our series 250 are integrated in or / VA housings. The FEP-coated sensor cable, in the lengths 2 m and 5 m, is the connection to the evaluation unit and may also be used under high-temperature conditions. The evaluation unit is connected to the sensor by means of a plug-in connector. On the sensor side the cable is permanently cast in or equipped with a temperature-resistant plug-in-connector ( Y-version. The sensing distance for high temperature sensors can be adjusted on the evaluation unit and the switching state is displayed by a LED. The sensing distance adjustment should be made at operating temperature. Here the maximum specified sensing distance and the temperature drive must be taken into consideration. All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

15 Type Code Example: KAS A - M32 - /VA - 100C - Z Series Version Body version Output signal KAS = Capacitive proximity sensor KS = Capacitive Sensor / Capacitive probe KSA = Capacitive evaluation unit ATEX, if existing NL = Normline E = Special version if existing Kind of adjustment Electrical connection Extended ambient temperature range Further functions, if existing Time delay, if existing Housing material Thread size / Process connection All specifications are subject to change without notice. (04/2017 Position 2 Serie Output Supply voltage 40 NAMUR DIN , ATEX DC 42 NAMUR DIN , ohne ATEX DC 70 NPN DC 80 PNP DC 7080 NPN / PNP DC 83 PNP DC 90 FET output AC / DC 95 Relay output AC / DC 250 High-temperature evaluation unit, probe Evaluation unit AC / DC, Probe passive 700 Level Master NPN DC 701 Level Master NPN XS DC 800 Level Master PNP DC 801 Level Master PNP XS DC 1000 Thyristor output AC / DC 2000 NPN/PNP selectably via change-over switch DC RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 15

16 Type Code Value Body size (Ø = mm Position 3 Mounting verion Special length (mm A11 M8 x 1 Flush - A21 M8 x 1 Non-flush - A21/63 M8 x 1 Non-flush 63 A12 M12 x 1 Flush - A22 M12 x 1 Non-flush - A13 M18 x 1 Flush - A23 M18 x 1 Non-flush - A14 M30 x 1,5 Flush - A14/40 M30 x 1,5 Flush 40 A24 M30 x 1,5 Non-flush - A24/50 M30 x 1,5 Non-flush 50 A24/90 M30 x 1,5 Non-flush 90 6/15 Ø 6 Flush /20 Ø 6,3 Flush /20 Ø 6,5 Non-flush 20 M8/15 M8 x 1 Flush 15 M8/25 M8 x 1 Non-flush 26 M10/70 M10 x 1,5 Non-flush Ø 11 Flush - 14 Ø 11 Non-flush - M16 M16 x 1,5 Non-flush - G1/4 G1/4 Non-flush - G3/8 G3/8 Non-flush - G1/2 G1/2 Non-flush - G3/8/35 G38 Non-flush 35 G3/8/50 G3/8 Non-flush 50 G3/8 G3/8 Non-flush 150 R3/8/35 R3/8 Non-flush Ø 18 Flush - 18/4 Ø 18 Flush 4 M18/50 M18 x 1 Non-flush 50 M18/150 M18 x 1 Non-flush Ø 20 Flush - 20 Ø 22 Flush - 20 M22 x 1,5 Flush - 20/5 Ø 20 Flush 5 20/137 Ø 20 Non-flush Ø 20 Non-flush - 23 Ø 22 Non-flush - 23 M22 x 1,5 Non-flush - 23/170 Ø 22 Non-flush 170 Value Body size (Ø = mm Position 3 Cylindrical Cylindrical Mounting version 26/105 Ø 15 Non-flush /113 Ø 26 Non-flush /160 Ø 15 Non-flush /200 Ø 26 Non-flush /240 Ø 26 Non-flush /300 Ø 26 Non-flush /400 Ø 26 Non-flush /416 Ø 26 Non-flush /445 Ø 26 Non-flush Ø 30 Flush - 30/10 Ø 30 Flush 10 30/50 Ø 30 Flush 50 30/40 Ø 30 Flush 40 30EM/15 Ø 30 Flush - 30/60 Ø 30 Flush Ø 32 Non-flush - 35 M32 x 1,5 Non-flush - 35/22 Ø 38 Non-flush 22 35/50 M32 x 1,5 Non-flush Ø 34 Flush - 38 Ø 34 Non-flush - 40 Ø 40 Flush - 41 Ø 40 Non-flush - 50 Ø 50 Flush - 53 Ø 50 Non-flush - 61 Ø 64 Non-flush - C20 46 x 74,5 Quader Non-Flush - C30EM/8 34 x 34 Quader Flush - C40/ x 80 Quader Flush - x 30 C41/ x 80 Quader Non-flush - x 30 P50 Paddle Smartpaddle Non-flush - BB 50 x 50 Quader Non-flush - x 26 B 46,6 x Quader Non-flush - 74,5 x 30 BXL 110 x 70 x 40 Quader Non-flush - Special length (mm All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

17 Type Code Value A S Ö P N IL4/UL0 IL20/UL10 IL4 IL20 1CO 1COR X Position 4 Output signal (NO + NC Normally open (NO Normally closed (NC Normally open / Normally closed changeable NAMUR Analogue output ma/ V Analogue output ma/ V Analogue current output ma Analogue current output ma Micro controller, 1 Change-over contact Micro controller, 1 Change-over contact Passiv Position 5 Value Thread / Process connection M8 M8 x 1 M12 M12 x 1 M14 M14 x 1 M16 M16 x 1 M18 M18 x 1 M22 M22 x 1,5 M30 M30 x 1,5 M32 M32 x 1,5 G1/2 G1/2 G3/4 G3/4 G1 G1 G11/2 G1 1/2 NPT1/4 NPT 1/4 R3/8 R3/8 PFM22 M22 x 1,5 PFM30 M30 x 1,5 TRI Triclamp PFS1 Fit PFS1 PFS2 Fit PFS2 F30 Fit F30 All specifications are subject to change without notice. (04/2017 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 17

18 Type Code Position 6 Material Active surface Housing Ceramic/VAb Ceramics Stainless steel No (AISI 303 LCP Liquid crystal polymer Liquid crystal polymer LCP/VAb Liquid crystal polymer Stainless steel No (AISI 303 PA Polyamide 6.6. glass-fibre reinforced Polyamide 6.6. glass-fibre reinforced PA/MS Polyamide 6.6. glass-fibre reinforced Brass nickel PA/VAb Polyamide 6.6. glass-fibre reinforced Stainless steel No (AISI 303 PBT/MS Polybutyleneterephthalate Brass nickel PC Polycarbonate Polycarbonate PEEK Polyetheretherketone FDA 21 CFR Polyetheretherketone FDA 21 CFR PEEK/VAa Polyetheretherketone FDA 21 CFR Stainless steel No (AISI 304 PEEK/VAb Polyetheretherketone FDA 21 CFR Stainless steel No (AISI 303 PEEK/VAc Polyetheretherketone FDA 21 CFR Stainless steel No (AISI 316L POM Polyoxymethylene Polyoxmethylene PP Polypropylene Polypropylene PPO Polyphenylenoxide Polyphenylenoxide PPO/MS Polyphenylenoxide Brass nickel PPO/VAb Polyphenylenoxide Stainless steel No (AISI 303 Polytetrafluoroethylene FDA 21 CFR Polytetrafluoroethylene FDA 21 CFR /AL Polytetrafluoroethylene FDA 21 CFR Aluminium /VAa Polytetrafluoroethylene FDA 21 CFR Stainless steel No (AISI 304 /VAb Polytetrafluoroethylene FDA 21 CFR Stainless steel No (AISI 303 /VAc Polytetrafluoroethylene FDA 21 CFR Stainless steel No (AISI 316L /MS Polytetrafluoroethylene FDA 21 CFR Brass nickel PVC Polyvinylchloride Polyvinylchloride PVC/MS Polyvinylchloride Brass nickel PVC/VAb Polyvinylchloride Stainless steel No (AISI 303 PVDF Polyvinylidene fluoride Polyvinylidene fluoride All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

19 Type Code Position 7 Position 8 Position 9 Value Time delay No No time delay indication OND Switch-on delay OFD Switch-off delay TD Time delay (switch-on delay / switch-off delay Value EST G HC More properties Protection against electrostatic discharge For highly adhesive products Products with a high dielectric constant or conductivity Value No indication 90C 90 C 100C 100 C 120C 120 C Advanced temperature range No advanced temperature range TDE Time delay, special version 150C 150 C 160C 160 C 180C 180 C 250C 250 C All specifications are subject to change without notice. (04/2017 Value Z0E Z01 Z02 Z03 Z04 Z05 Z10 Y1 Y3 Y5 Y9 Y10 Y7 Y8 Y5C Y7C Y8C YEC Y12 Y20 Y21 KL Value NL No indication - Position 10 Electrical connection Special cable length 1 m connection cable 2 m connection cable 3 m connection cable 4 m connection cable 5 m connection cable 10 m connection cable Flange connector M 12 x 1, AC, 2 Pin Flange connector M 12 x 1 (Plastic, DC, 4 Pin Flange connector M 12 x 1 (Metal, DC, 4 Pin Flange connector M 12 x 1, AC, 3 Pin Flange connector M 12 x 1, DC, 5 Pin Flange connector M 8 x 1, DC, 3 Pin Flange connector M 8 x 1, DC, 4 Pin Coupling plug M 12 x 1, DC, 4 Pin Coupling plug M 8 x 1, DC, 3 Pin Coupling plug M 8 x 1, DC, 4 Pin Coupling plug special housing Flange connector M 8 x 1 (Metal, DC, 4 Pin Connection to evaluation unit / Sensor Y20 Connection to evaluation unit / Sensor Y21 Terminal connection Position 13 Device family NormLine HighPerformance Position 11 Value Sensitivity adjustment 1 Potentiometer 0 Fix adjusted, no adjustment possible ET Easyteach with button ETM EasyTeach by Magnet ETW EasyTeach by Wire MaG Mount and Go, fix adjusted CMaG Customer Mount and Go, fix adjusted Value E EBC BS Leak Position 12 Special version Special version C-housing (PA for separate evaluation unit Blue Sense LEAK-Sensor Position 14 Value Device for use in areas with the risk of explosion StEx For ATEX zone 20 3D With manufacturer declaration for ATEX zone 22 3G With manufacturer declaration for ATEX zone 2 3D3G With manufacturer declaration for ATEX zone 22 and 2 StEx3G For ATEX zone 20 With manufacturer declaration for ATEX zone 2 (gas RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 19

20 Capacitive Sensors with Semispherical Active Surface - S26 The capacitive S26 sensors have a semispherical active surface as an outer sign indicating that this is an extraordinary device for level control. This natural shape facilitates draining of materials and thus enhances the antistatic and anti-stick characteristics of the housing made of. At the same time the cleanability is improved. In connection with the patented electrode structure, which is specially designed for the S26 sensor, there is a sensor at your disposal that is very insensitive to soiling or material adhesion. This guarantees a safe and reliable level detection. On demand this sensor is available with built-in Bluetooth function for wireless data transfer. To complete this range there are models with ATEX certificate for use in areas with danger of explosion, dust zone 20 or gas zone 0. For applications with higher demand on mechanical, e. g. for applications with higher pressure or for the detection of abrasive media, like sugar or salt, we recommend the use of the S26 sensor with a robust PEEK body. Process connections The capacitive S26 sensors are suitable for level control of most different products. They are used in the Semiconductor Industry, Chemical Industry and in the Food Industry. These sensors are available with different process connections, like G1, M22, Triclamp and with modified body sizes for standard plastic pipe fitting systems. Electrical versions There are models for V DC and V AC/DC Non-flush mounting All S26 sensors are for non-flush mounting. That means they are designed for applications, where the active area of the sensor is in contact with the material to be detected. With this kind of level control the sensor head (active area is completely immersed into the powder, granulate or liquid. All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

21 CAPACITIVE SENSORS KAS S26 Pages Capacitive sensors S26 body size G 1/ Capacitive sensors S26 body size Ø 22 mm to M Capacitive sensors S26 body size F Capacitive sensors S26 body size M Capacitive sensors S26 body size G Capacitive sensors S26 body size Triclamp Capacitive sensors S26 body size PFM30 / PFS Capacitive sensors S26 special body size 63 Capacitive sensors S26 body size G 3/4 64 Capacitive sensors S26, AC / DC All specifications are subject to change without notice. (04/2017 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 21

22 G1/2" Ø18,6 Ø15 SW20 Ø22,1 Series 70 - NPN Series 80 - PNP Type of construction G 1/2 Housing material: PEEK CIP SIP mm Electrical version 4-wire DC Type NPN KAS A-K-G1/2 -PEEK Art.-No. KA 1245 Connection diagram No. 1 KAS A-K-G1/2 -PEEK Art.-No. KA 1244 Connection diagram No V DC 2 x ma 2 Hz C / CIP 121 C (zero-current Connection cable 2 m, PVC, 4 x 0.34 mm² Housing material (part in contact with the medium PEEK (FDA 21 CFR Active surface PEEK (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: Varivent Adapter, Welding Socket please see our selection of accessories Advantages: EHEDG-Certified Measurement is independent of the mounting position Permitted pressure on the active area: 10 bar All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

23 G1/2" Ø18,6 Ø15 SW20 Ø22,1 Series 80 - PNP Type of construction G 1/2 Easy Teach by wire Housing material: PEEK ETW EasyTeach EHEDG CIP SIP All specifications are subject to change without notice. (04/ mm Electrical version 4-wire DC KAS-80-26/105-A-G1/2-PEEK-Z02-ETW- Art.-No. KA V DC 2 x ma Max. 15 Hz C / CIP 121 C (zero-current Connection cable 2 m, PVC, 5 x 0.14 mm² Housing material PEEK (FDA 21 CFR Active surface PEEK (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: Varivent Adapter, Welding Socket please see our selection of accessories. * Position of the EasyTeach button sealed with sealing screw EasyTeachchart: Advantages: EHEDG Measurement is independent of the mounting position Permitted pressure on the active area: 10 bar. LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 23

24 Ø22 Ø26 M12x1 Series 80 - PNP Type of construction Ø 22 mm Useable for an ambient temperature up to +100 C With flange connector M 12 x 1 CIP SIP 100 C 212 F High Temperature Electrical version 4-pin DC KAS-80-26/113-A-D C-Y5-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PEEK (FDA 21 CFR Accessories (not delivered with the sensor: For matching connectors please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

25 Ø22 ± 0,05 Ø26 M12x1 Series 80 - PNP Type of construction Ø 22 mm Useable for an ambient temperature up to +100 C With flange connector M 12 x 1 CIP SIP 100 C 212 F High Temperature All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC KAS-80-26/113-A-D C-Y5-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PEEK (FDA 21 CFR Accessories (not delivered with the sensor: For matching connectors please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 25

26 Ø28,3 M 22 x1,5 Ø20,3 Ø35 M 30 x1,5 Series 80 - PNP Type of construction M 22 x 1.5 CIP SIP Electrical version 4-wire DC KAS-80-26/113-A-M22--Z03-1-E- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection cable 3 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid (FDA 21 CFR Accessories (not delivered with the sensor: Protection Set M30 / # please see our selection of accessories ,9 All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

27 Ø25,5 29,75 Ø40 M12x1 Series 80 - PNP Type of construction F 30 Special version with flange, double gasket for hole basis fitting Ø 30 mm. Useable for an ambient temperature up to +100 C With flange connector M 12 x 1 CIP SIP 100 C 212 F High Temperature All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC KAS-80-26/113-A-F C-Y5-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For matching connectors please see our selection of accessories. ±0, RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 27

28 Ø25,5 29,75 Ø40 M12x1 Series 80 - PNP Type of construction F30 Special version with flange, double gasket for hole basis fitting Ø 30 mm. Easy Teach by wire Useable for an ambient temperature up to +100 C With flange connector M 12 x 1 ETW EasyTeach 100 C 212 F High Temperature CIP SIP Electrical version 5-pin DC KAS-80-26/113-A-F C-Y10-ETW- Art.-No. KA V DC 2 x ma Max. 15 Hz C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For matching connectors please see our selection of accessories. * Position of the EasyTeach button sealed with sealing screw ±0, EasyTeachchart: LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

29 M 30 x1,5 Ø25,5 Ø40 M 12 x1 Series 80 - PNP Type of construction M 30 x 1.5 With flange connector M 12 x 1 CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC KAS-80-26/113-A-M30--Y5-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For matching connectors please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 29

30 Ø25,5 M30x1,5 SW36 Ø40 Series 80 - PNP Type of construction M 30 x 1.5 Easy Teach by wire ETW EasyTeach CIP SIP Electrical version 4-wire DC KAS-80-26/113-A-M30--Z03-ETW- Art.-No. KA V DC 2 x ma Max. 15 Hz C / CIP 121 C (zero-current Connection cable 3 m, PVC, 5 x 0.34 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA / PPO * Position of the EasyTeach button sealed with sealing screw EasyTeachchart: LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

31 Ø25,5 G1" SW36 Ø40 Series 70 - NPN Series 80 - PNP Type of construction G 1 CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC Type NPN KAS-70-26/113-A-G1--Z02-1- Art.-No. KA 1078 Connection diagram No. 3 KAS-80-26/113-A-G1--Z02-1- Art.-No Connection diagram No V DC 2 x ma C / CIP 121 C (zero-current Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

32 Ø25,5 G1" SW36 Ø40 Series 80 - PNP Type of construction G 1 CIP SIP Electrical version 4-wire DC KAS-80-26/113-A-G1--Z10-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection cable 10 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

33 Ø25,5 G1" SW36 Ø40 Series 80 - PNP Type of construction G 1 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor With Bluetooth function Bluetooth All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC Output (NO + NC KAS-80-26/113-A-G1--Z02-BS- Art.-No. KA V DC 2 x ma 2 Hz C Degree of protection IEC IP 67 Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Bulk materials, like plastic granules, powder, cereals,feedstuffs etc. With Bluetooth control function for: Sensor sensitivity Optimal sensor adjustment Deposits on the s e n s o r surface. RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 33

34 Ø25,5 G1" SW36 Ø40 Series 80 - PNP Type of construction G 1 Easy Teach Push Button ET EasyTeach CIP SIP Electrical version 4-wire DC KAS-80-26/113-A-G1--Z02-ET- Art.-No. KA V DC 2 x ma Max. 15 Hz C / CIP 121 C (zero-current Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories. * Position of the EasyTeach button sealed with sealing screw EasyTeachchart: LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

35 Ø25,5 G1" SW36 Ø40 Series 80 - PNP Type of construction G 1 Easy Teach Push Button ET EasyTeach CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC KAS-80-26/113-A-G1--Z02-ET-E- Art.-No. KA V DC 2 x ma 1 Hz C / CIP 121 C (zero-current Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories. * Position of the EasyTeach button sealed with sealing screw EasyTeachchart: LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 35

36 Ø25,5 G1" SW36 Ø40 Series 80 - PNP Type of construction G 1 Easy Teach by wire ETW EasyTeach CIP SIP Electrical version 4-wire DC KAS-80-26/113-A-G1--Z02-ETW- Art.-No. KA V DC 2 x ma Max. 15 Hz C / CIP 121 C (zero-current Connection cable 2 m, PVC, 5 x 0.34 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories. * Position of the EasyTeach button sealed with sealing screw EasyTeachchart: LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

37 G1" Ø25,5 Ø40 M 12 x1 Series 70 - NPN Series 80 - PNP Type of construction G 1 With flange connector M 12 x 1 CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC Type NPN KAS-70-26/113-A-G1--Y5-1- Art.-No. KA 0844 Connection diagram No. 3 KAS-80-26/113-A-G1--Y5-1- Art.-No. KA 0642 Connection diagram No V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 37

38 G1" Ø25,5 Ø40 SW36 M12x1 Series 80 - PNP Type of construction G 1 Easy Teach by wire With flange connector M 12 x 1 ETW EasyTeach CIP SIP Electrical version 4 - pin DC KAS-80-26/113-A-G1--Y10-ETW- Art.-No. KA V DC 2 x ma Max. 15 Hz C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories. * Position of the EasyTeach button sealed with sealing screw EasyTeachchart: LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

39 G1" Ø26 SW36 Ø40 M12x1 Series 80 - PNP Type of construction G 1 Easy Teach by wire Housing material: PEEK With flange connector M 12 x 1 ETW EasyTeach CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4 - pin DC KAS-80-26/113-A-G1-PEEK-Y10-ETW- Art.-No. KA V DC 2 x ma Max. 15 Hz C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material PEEK (FDA 21 CFR Active surface PEEK (FDA 21 CFR Lid PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories. * Position of the EasyTeach button sealed with sealing screw 77 67,5 96,5 92, ,5 EasyTeachchart: LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 39

40 Ø25,5 G1" SW36 Ø40 Series 80 - PNP Type of construction G 1 Housing material: PP Quattro E C Protect mm Electrical version 4-wire DC KAS-80-26/113-A-G1-PP-Z02-1-NL Art.-No. KA V DC Permitted residual ripple max. 5 % 2 x ma C Yellow Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material PP (FDA 21 CFR Active surface PP (FDA 21 CFR Lid PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

41 Ø25,5 G1" SW36 Ø40 Series 80 - PNP Type of construction G 1 Useable for an ambient temperature up to +100 C 100 C 212 F High Temperature CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC KAS-80-26/113-A-G1--100C-Z02-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 41

42 G1" Ø25,5 Ø40 M 12 x1 Series 80 - PNP Type of construction G 1 Useable for an ambient temperature up to +100 C With flange connector M 12 x C 212 F High Temperature CIP SIP Electrical version 4-pin DC KAS-80-26/113-A-G1--100C-Y5-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

43 G1" Ø25,5 Ø40 M 12 x1 Series 80 - PNP Type of construction G 1 Useable for an ambient temperature up to +100 C With flange connector M 12 x 1 Plug connection not norm Plug connection 1 = -, 3 = +, 4 = A 100 C 212 F High Temperature CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC Normally closed KAS-80-26/113-Ö-G1--100C-Y5-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 43

44 Ø25,5 G1" SW36 Ø40 Series 80 - PNP Type of construction G 1 Useable for an ambient temperature up to +120 C Quattro E C Protect 120 C 248 F High Temperature mm Electrical version 4-wire DC KAS-80-26/113-A-G1--120C-Z02-1-NL Art.-No. KA V DC Permitted residual ripple max. 5 % 2 x ma C / CIP 121 C (zero-current Yellow Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

45 G1" Ø25,5 Ø40 Series 80 - PNP Process connection: G 1 Maximum ambient temperature 180 C 180 C 180 C 356 F High Temperature All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC KAS-80-26/150-A-G1--180C-Z02-1- Art.-No. KA V DC 2 x ma C (for active zone C Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories , RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 45

46 Ø25,5 G1" Ø40 M 32 x1,5 Series 70 - NPN Series 80 - PNP Type of construction G 1 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor CIP SIP Electrical version 4-wire DC Type NPN KAS-70-26/200-A-G1--Z02-1- Art.-No. KA 1287 Connection diagram No. 3 KAS-80-26/200-A-G1--Z02-1- Art.-No. KA 0653 Connection diagram No V DC 2 x ma C / CIP 121 C (zero-current Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and protection Set M32 / # please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

47 G1" Ø25,5 M 32 x1,5 SW36 Series 80 - PNP Type of construction G 1 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC KAS-80-26/200-A-G1--Z05-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection cable 5 m,, 4 x 0.22 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and protection Set M32 / # please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 47

48 Ø25,5 G1" Ø40 M 32 x1,5 Series 80 - PNP Type of construction G 1 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor CIP SIP Electrical version 4-wire DC KAS-80-26/200-A-G1--Z10-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection cable 10 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and protection Set M32 / # please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

49 Ø25,5 G1" Ø40 M 32 x1,5 Series 80 - PNP Type of construction G 1 Easy Teach Push Button Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor ET EasyTeach CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC KAS-80-26/200-A-G1--Z02-ET- Art.-No. KA V DC 2 x ma Max. 15 Hz C / CIP 121 C (zero-current Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and protection Set M32 / # please see our selection of accessories. * Position of the EasyTeach button sealed with sealing screw EasyTeachchart: LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 49

50 Ø25,5 G1" M 32 x1,5 Ø40 M 12 x1 Series 80 - PNP Type of construction G 1 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor With flange connector M 12 x 1 CIP SIP Electrical version 4-pin DC KAS-80-26/200-A-G1--Y5-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

51 Ø25,5 G1" M 32 x1,5 Ø40 M 12 x1 Series 80 - PNP Type of construction G 1 Useable for an ambient temperature up to +100 C Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor With flange connector M 12 x C 212 F High Temperature CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC KAS-80-26/200-A-G1--100C-Y5-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 51

52 G1" Ø25,5 Ø30,2 Ø40 M 12 x1 Series 80 - PNP Type of construction G 1 With flange connector M 12 x 1 CIP SIP Electrical version 4-pin DC KAS-80-26/300-A-G1--Y5-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

53 Ø25 SW32 Ø37 G1" Series 80 - PNP Type of construction G 1 Easy Teach by wire Connection head and process connection stainless steel VA no / AISI 316L Housing material: Polypropylene (PP Bodylength 416 mm Other bodylegths on request ETW EasyTeach All specifications are subject to change without notice. (04/2017 Level sensor, in contact with the product Operating distance min. / max. programmable Electrical version 406, Medium dependent adjustable mm 4-wire DC KAS-80-26/416-A-G1-PP/VAc-Z02-ETW- Art.-No. KA V DC Permitted residual ripple max. 10% 2 x ma 15 Hz C Degree of protection IEC IP 67 Connection cable Housing material process connection 2 m, PVC, 5 x 0.34 mm² VA, No / AISI 316L (FDA ing Active surface Polypropylene (PP (FDA 21 CFR Lid PA / PPO EasyTeachchart: oil, chemicals and much more. LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 53

54 G1" Ø25 M 12 x1 Series 80 - PNP Type of construction G 1 Easy Teach by wire Connection head and process connection stainless steel VA no / AISI 316L Housing material: Polypropylene (PP Bodylength 416 mm Other bodylegths on request With flange connector M 12 x 1 ETW EasyTeach Level sensor, in contact with the product Operating distance min. / max. programmable Electrical version , Medium dependent adjustable mm 4-pin DC KAS-80-26/416-A-G1-PP/VAc-Y10-ETW- Art.-No. KA V DC 2 x ma 15 Hz C Degree of protection IEC IP 67 Connection Flange connector M 12 x 1 Housing material process connection VA, No / AISI 316L (FDA ing Active surface Polypropylene (PP (FDA 21 CFR Lid PA / PPO EasyTeachchart: oil, chemicals and much more. LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

55 Ø43,5 Ø50 Ø25,5 Ø34,7 Series 70 - NPN Series 80 - PNP Type of construction Triclamp DN 25 Useable for an ambient temperature up to +100 C CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC Type NPN KAS-70-26/113-A-TRI--100C-Z02-1- Art.-No. KA 1025 Connection diagram No. 3 KAS-80-26/113-A-TRI--100C-Z02-1- Art.-No. KA 0415 Connection diagram No V DC 2 x ma C / CIP 121 C (zero-current Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: Stainless steel welding nipple DN 25 # , Sealing gasket # , Triclamp mounting clamp # please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 55

56 Ø50 Ø43,5 Ø25,5 Ø34,7 M 12 x1 Series 80 - PNP Type of construction Triclamp DN 25 Useable for an ambient temperature up to +100 C With flange connector M 12 x C 212 F High Temperature CIP SIP Electrical version 4-pin DC KAS-80-26/113-A-TRI--100C-Y5-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: Stainless steel welding nipple DN 25 # , Sealing gasket # , Triclamp mounting clamp # and matching connectors please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

57 Ø50 Ø43,5 Ø25,5 Ø34,7 M 12 x1 Series 80 - PNP Type of construction Triclamp DN 25 Easy Teach Push Button Useable for an ambient temperature up to +100 C With flange connector M 12 x 1 ET EasyTeach 100 C 212 F High Temperature CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC KAS-80-26/113-A-TRI--100C-Y5-ET- Art.-No. KA V DC 2 x ma Max. 15 Hz C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: Stainless steel welding nipple DN 25 # , Sealing gasket # , Triclamp mounting clamp # and matching connectors please see our selection of accessories. * Position of the EasyTeach button sealed with sealing screw EasyTeachchart: LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 57

58 Ø50 Ø25,5 Ø34,7 Ø46,5 M 12 x1 Series 80 - PNP Type of construction 2 x Triclamp DN 25 Useable for an ambient temperature up to +100 C With flange connector M 12 x 1 CIP SIP 120 C 248 F High Temperature Electrical version 4-pin DC KAS-80-26/113-A-TRI--100C-Y5-1-E- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: Stainless steel welding nipple DN 25 # , Sealing gasket # , Triclamp mounting clamp # , sealing cap # and matching connectors please see our selection of accessories ,5 110 All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

59 25,5 M30x1,5 Series 80 - PNP Type of construction PF M 30 x 1,5 Easy Teach by wire Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor ETW EasyTeach CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC KAS-80-26/113-A-PFM30--Z03-ETW- Art.-No. KA V DC 2 x ma Max. 15 Hz C / CIP 121 C (zero-current Connection cable 3 m, PVC, 5 x 0.34 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA / PPO Accessories (not delivered with the sensor: * Position of the EasyTeach button sealed with sealing screw 70, EasyTeachchart: LED / Yellow = A1 Green = A2 Adjustment empty Initializing empty Adjustment full Initializing full Factory reset Test RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 59

60 Ø44,6 Ø25,5 Ø33 Ø41 Series 80 - PNP Type of construction PFS2 CIP SIP Electrical version 4-wire DC KAS-80-26/113-A-PFS2--Z02-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: PP / EPDM Screwing da 32 SDR with sealing gasket # , PP union nut Ø 32 mm # please see our selection of accessories ,5 80 All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

61 Ø41 Ø33 Ø25,5 Ø44,6 Series 80 - PNP Type of construction PFS1 CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC KAS-80-26/113-A-PFS1--Z05-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection cable 5 m,, 4 x 0.22 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid (FDA 21 CFR Accessories (not delivered with the sensor: PP tube da 32 SDR 11, L = 2000 mm with already welded screw connection on one side # , PP union nut Ø 32 mm # , O- ring EPDM, suitable for union nut da 32 # please see our selection of accessories. 100,9 85,5 81, ,7 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 61

62 Ø44,6 Ø33 Ø41 Ø25,5 M 12 x1 Series 80 - PNP Type of construction PFS1 With flange connector M 12 x 1 CIP SIP Electrical version 4-pin DC KAS-80-26/113-A-PFS1--Y5-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: PP tube da 32 SDR 11, L = 2000 mm with already welded screw connection on one side # , PP union nut Ø 32 mm # , O-ring EPDM, suitable for union nut Ø 32 mm # and matching connectors please see our selection of accessories. 100,9 85, ,7 11 All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

63 G1" Ø29,4 Ø25,4 Ø30 M 12 x1 Series 80 - PNP Type of construction G 1 Housing material: PEEK Special housing for applications with high demands on hygiene. With flange connector M 12 x 1 CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC KAS-80-26/113-A-G1-PEEK-Y5-1-E- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material PEEK (FDA 21 CFR Active surface PEEK (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories. 44,2 41,2 35,2 6x17 56,7 112,7 13 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 63

64 3/4" Ø24 SW36 Ø40 Series 80 - PNP Type of construction G 3/4 CIP SIP Electrical version 4-wire DC KAS-80-26/113-A-G3/4--Z02-1- Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

65 M30x1,5 Ø25,5 Ø40 Series 90 - AC / DC Type of construction M 30 x 1.5 Housing material: PP mm Electrical version 2-wire AC / DC Normally open Type KAS-90-26/113-S-M30-PP-Z02-1-NL Art.-No. KA V AC / DC 6.0 V ma Typ. 2.5 ma 25 Hz C Yellow Connection cable 2 m, PVC, 2 x 0.75 mm² Housing material PP (FDA 21 CFR Active surface PP (FDA 21 CFR Lid PA / PPO All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 65

66 Ø25,5 G1" SW36 Ø40 Series 90 - AC / DC level control of products with a solutions and much more. Type of construction G 1 Quattro E C Protect CIP SIP Medium dependent adjustable mm mm Electrical version 2-wire AC / DC 2-wire AC / DC Normally open Normally closed Type KAS-90-26/113-S-G1--Z02-1 KAS-90-26/113-Ö-G1--Z02-1 Art.-No. KA 0409 KA 0685 Connection diagram No V AC / DC V AC / DC 6.0 V 6.0 V ma ma Typ. 2.5 ma Typ. 2.5 ma 25 Hz 25 Hz C / CIP 121 C (zero-current C / CIP 121 C (zero-current Yellow Yellow IP 67* EN Connection cable 2 m, PUR, 2 x 0.75 mm² 2 m, PUR, 2 x 0.75 mm² Housing material (FDA 21 CFR (FDA 21 CFR Active surface (FDA 21 CFR (FDA 21 CFR Lid PA / PPO PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

67 Ø25,5 G1" SW36 Ø40 Series 90 - AC / DC Type of construction G 1 Quattro E C Protect CIP SIP All specifications are subject to change without notice. (04/ mm Electrical version 2-wire AC / DC Normally open Type KAS-90-26/113-S-G1--Z05-1 Art.-No. KA V AC / DC 6.0 V ma Typ. 2.5 ma 25 Hz C / CIP 121 C (zero-current Yellow Connection cable 5 m, PUR, 2 x 0.75 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 67

68 G1" Ø25,5 Ø40 M 12 x1 Series 90 - AC / DC level control of products with a solutions and much more. Type of construction G 1 With flange connector M 12 x 1 Quattro E C Protect CIP SIP Medium dependent adjustable mm mm Electrical version 2-pin AC / DC 2-pin AC / DC Normally open Normally closed Type KAS-90-26/113-S-G1--Y1-1 KAS-90-26/113-Ö-G1--Y1-1 Art.-No. KA 0639 KA 1013 Connection diagram No V AC / DC V AC / DC 6.0 V 6.0 V ma ma Typ. 2.5 ma Typ. 2.5 ma 25 Hz 25 Hz C / CIP 121 C (zero-current C / CIP 121 C (zero-current Yellow Yellow IP 67* EN Connection Flange connector M 12 x 1 Flange connector M 12 x 1 Housing material (FDA 21 CFR (FDA 21 CFR Active surface (FDA 21 CFR (FDA 21 CFR Lid PA / PPO PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

69 Ø43,5 Ø50 Ø25,5 Ø34,7 Series 90 - AC / DC level control of products with a solutions and much more. Type of construction Triclamp DN 25 Quattro E C Protect CIP SIP All specifications are subject to change without notice. (04/2017 Medium dependent adjustable mm mm Electrical version 2-wire AC / DC 2-wire AC / DC Normally open Normally closed Type KAS-90-26/113-S-TRI--Z02-1 KAS-90-26/113-Ö-TRI--Z02-1 Art.-No. KA 0684 KA 0683 Connection diagram No V AC / DC V AC / DC 6.0 V 6.0 V ma ma Typ. 2.5 ma Typ. 2.5 ma 25 Hz 25 Hz C / CIP 121 C (zero-current C / CIP 121 C (zero-current Yellow Yellow IP 67* EN Connection cable 2 m, PUR, 2 x 0.75 mm² 2 m, PUR, 2 x 0.75 mm² Housing material (FDA 21 CFR (FDA 21 CFR Active surface (FDA 21 CFR (FDA 21 CFR Lid PA / PPO PA / PPO Accessories (not delivered with the sensor: Stainless steel welding nipple DN 25 # , Sealing gasket # , Triclamp mounting clamp # please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 69

70 70 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax All specifications are subject to change without notice. (04/2017

71 CAPACITIVE SENSORS KAS S26 StEx - ATEX Pages Capacitive sensors S26, series 40 NAMUR, StEx - ATEX zone 0, zone 20, G 1 Capacitive sensors S26, series 70 / 80, StEx - ATEX zone 1, zone 20, G 1/2 Capacitive sensors S26, series 70 / 80, StEx - ATEX zone 1, zone 20, Ø 22 Capacitive sensors S26, series 70 / 80, StEx - ATEX zone 1, zone 20, F 30 Capacitive sensors S26, series 70 / 80, StEx - ATEX zone 1, zone 20, M 30 Capacitive sensors S26, series 70 / 80, StEx - ATEX zone 1, zone 20, M 32 Capacitive sensors S26, series 70 / 80, StEx - ATEX zone 1, zone 20, G 1 Capacitive sensors S26, series 70 / 80, StEx - ATEX zone 1, zone 20, Triclamp Capacitive sensors S26, series 70 / 80, StEx - ATEX zone 1, zone 20, HG All specifications are subject to change without notice. (04/2017 Capacitive sensors S26 with manufacturer declaration RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 71

72 G1" Ø25,5 Ø40 Series 40 - NAMUR EN Type of construction G 1 For use in areas with the risk of gas explosion, zone 0 DMT 03 ATEX E 048 IECEx BVS II 1G Ex ia IIC T1-T6 Ga Ex ia IIC T1-T6 Ga High Performance CIP SIP mm Electrical version 2-wire DC NAMUR DIN Type KAS N-K-G1 - Art.-No. KA V DC, U i = 15 V DC Output current active surface free < typ. 1.5 ma Output current active surface covered > typ. 3 ma Self-inductance (L 0.2 mh Self-capacitance (C 250 nf Permitted residual ripple max. 5 % C / CIP 121 C (zero-current Yellow Connection cable 2 m, PUR, 2 x 0.75 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

73 G1" Ø25,5 Ø40 Series 40 - NAMUR EN Type of construction G 1 For use in areas with the risk of gas explosion, zone 0 Useable for an ambient temperature up to +100 C DMT 03 ATEX E 048 IECEx BVS II 1G Ex ia IIC T1-T6 Ga Ex ia IIC T1-T6 Ga High Performance CIP SIP 100 C 212 F High Temperature All specifications are subject to change without notice. (04/ mm Electrical version 2-wire DC NAMUR DIN Type KAS N-K-G C Art.-No. KA V DC, U i = 15 V DC Output current active surface free < typ. 1.5 ma Output current active surface covered > typ. 3 ma Self-inductance (L 0.2 mh Self-capacitance (C 250 nf Permitted residual ripple max. 5 % C / CIP 121 C (zero-current Yellow Connection cable 2 m, PUR, 2 x 0.75 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA / PPO Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 73

74 Ø26 M 22 x1 Series 40 - NAMUR EN Housing M22 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 0 SIP / CIP 121 C DMT 03 ATEX E 048 IECEx BVS II 1G Ex ia IIC T1-T6 Ga II 1D Ex ia IIIC T101 C Da Ex ia IIC T1-T6 Ga Ex ia IIIC T101 C Da High Performance CIP SIP mm Electrical version 2-wire DC Output NAMUR DIN Type KAS N-K-PFM22--StEx Art. No. KA V DC, U i = 15 V DC Output current active surface free < typ. 1.5 ma Output current active surface covered > typ. 3 ma Self-inductance (L 0.2 mh Self-capacitance (C 250 nf Permitted residual ripple max. 5 % C / CIP 121 C (zero-current Yellow Degree of protection IEC IP 67 Connection cable 2 m, PUR, 2 x 0.75 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (supplied with the sensor O-Ring Viton PG 16 Accessories for mounting (not delivered with the sensor please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

75 Ø34 Ø25,5 M 30 x1,5 Series 40 - NAMUR EN Housing M 30 x 1.5 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 0 SIP / CIP 121 C DMT 03 ATEX E 048 IECEx BVS II 1G Ex ia IIC T1-T6 Ga II 1D Ex ia IIIC T101 C Da Ex ia IIC T1-T6 Ga Ex ia IIIC T101 C Da High Performance CIP SIP All specifications are subject to change without notice. (04/2017 Level sensor, in contact with the product Electrical version 70,5 87,9 113 Medium dependent adjustable mm 2-wire DC Output NAMUR DIN Type KAS N-K-M30--StEx Art. No. KA 1389 Output current active surface free Output current active surface covered Self-inductance (L Self-capacitance (C 5-15 V DC, U i = 15 V DC < typ. 1.5 ma > typ. 3 ma 0.2 mh 250 nf Permitted residual ripple max. 5 % C / CIP 121 C (zero-current Yellow Degree of protection IEC IP 67 Connection cable 2 m, PUR, 2 x 0.75 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (supplied with the sensor O-Ring Viton PG 21 Accessories for mounting (not delivered with the sensor please see our selection of accessories. RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 75

76 Ø25,5 G1" Ø40 Series 40 - NAMUR EN Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 0 DMT 03 ATEX E 048 IECEx BVS II 1G Ex ia IIC T1-T6 Ga II 1D Ex ia IIIC T101 C Da Ex ia IIC T1-T6 Ga Ex ia IIIC T101 C Da High Performance CIP SIP mm Electrical version 2-wire DC NAMUR DIN Type KAS N-K-G1 --StEx Art.-No. KA V DC, U i = 15 V DC Output current active surface free < typ. 1.5 ma Output current active surface covered > typ. 3 ma Self-inductance (L 0.2 mh Self-capacitance (C 250 nf Permitted residual ripple max. 5 % C / CIP 121 C (zero-current Yellow Connection cable 2 m, PUR, 2 x 0.75 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

77 Ø25,5 G1" Ø40 Series 40 - NAMUR EN Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 0 DMT 03 ATEX E 048 IECEx BVS II 1G Ex ia IIC T1-T6 Ga II 1D Ex ia IIIC T101 C Da Ex ia IIC T1-T6 Ga Ex ia IIIC T101 C Da High Performance CIP SIP All specifications are subject to change without notice. (04/ mm Electrical version 2-wire DC NAMUR DIN Type KAS N-K-G1 --StEx Art.-No. KA V DC, U i = 15 V DC Output current active surface free < typ. 1.5 ma Output current active surface covered > typ. 2.5 ma Self-inductance (L 0.2 mh Self-capacitance (C 250 nf Permitted residual ripple max. 5 % C / CIP 121 C (zero-current Yellow Connection cable 5 m, PUR, 2 x 0.75 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 77

78 Ø25,5 G1" Ø40 M12x1 Series 40 - NAMUR EN Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 or use in areas with the risk of gas explosion, zone 0 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor With flange connector M 12 x 1 DMT 03 ATEX E 048 IECEx BVS II 1G Ex ia IIC T1-T6 Ga II 1D Ex ia IIIC T101 C Da Ex ia IIC T1-T6 Ga Ex ia IIIC T101 C Da High Performance CIP SIP mm Electrical version 2-pin DC NAMUR DIN Type KAS N-K-G Y5-StEx Art.-No. KA V DC, U i = 15 V DC Output current active surface free < typ. 1.5 ma Output current active surface covered > typ. 3 ma Self-inductance (L 0.2 mh Self-capacitance (C 250 nf Permitted residual ripple max. 5 % C / CIP 121 C (zero-current Yellow Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (delivered with the sensor Protective clip Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories. All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

79 Ø25,5 G1" Ø40 M12x1 Series 40 - NAMUR EN Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 0 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor With flange connector M 12 x 1 DMT 03 ATEX E 048 IECEx BVS II 1G Ex ia IIC T1-T6 Ga II 1D Ex ia IIIC T101 C Da Ex ia IIC T1-T6 Ga Ex ia IIIC T101 C Da High Performance CIP SIP All specifications are subject to change without notice. (04/ mm Electrical version 2-pin DC NAMUR DIN Type KAS N-K-G Y5-StEx Art.-No. KA V DC, U i = 15 V DC Output current active surface free < typ. 1.5 ma Output current active surface covered > typ. 3 ma Self-inductance (L 0.2 mh Self-capacitance (C 250 nf Permitted residual ripple max. 5 % C / CIP 121 C (zero-current Yellow Connection cable Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (delivered with the sensor Protective clip Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories. RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 79

80 Ø36 G 1/2" Ø15 Series 80 - PNP - StEx - ATEX Process connection: G 1/2 Housing material: PEEK SIP / CIP 121 C Special version with flange. Sealing can be made with a gasket or -tape (not supplied with the sensor DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db Operating distance S n / min. / max. adjustable 4 mm / mm Electrical version 4-wire DC KAS A-K-G1/2 -PEEK-StEx Art.-No. KA V DC Output current max. (I e 2 x ma 2 Hz C / CIP 121 C (zero-current Connection cable 2 m, PVC, 4 x 0.34 mm² Housing material (part in contact with the medium PEEK (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: Varivent Adapter, Welding Socket please see our selection of accessories. 49,3 43,2 73, It is ideal for the level control of liquids, pastes, powders and other bulk materials. This sensor has no moving parts and is not subject to wear or tear and thus there is no down time due to false detections caused by material build-up. Advantages: Measurement is independent of the mounting position Permitted pressure on the active area: 10 bar Process connection G 1/2 All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

81 G1/2" 18,3 Ø15 Ø22,1 Series 80 - PNP - StEx - ATEX Process connection: G 1/2 Housing material: PEEK For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db EHEDG CIP SIP All specifications are subject to change without notice. (04/ mm Electrical version 4-wire DC KAS A-K-160-G1/2-PEEK-StEx Art.-No. KA V DC Output current max. (I e 2 x ma 2 Hz C / CIP 121 C (zero-current Connection cable 2 m, PVC, 4 x 0.34 mm² Housing material (part in contact with the medium PEEK (FDA 21 CFR Lid PC Accessories (not delivered with the sensor: Varivent Adapter, Welding Socket please see our selection of accessories. 140, ,3 158,8 150 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 20 This capacitive level sensor is EHEDG. It is ideal for the level control of liquids, pastes, powders and other bulk materials. This sensor has no moving parts and is not subject to wear or tear and thus there is no down time due to false detections caused by material build-up. Advantages: EHEDG Measurement is independent of the mounting position Permitted pressure on the active area: 10 bar Process connection G 1/2 81

82 Ø22 Ø26 M12x1 Series 80 - PNP - StEx - ATEX Type of construction Ø 22 mm For use in areas with the risk of dust explosion, zone 20 With flange connector M 12 x 1 DMT 01 ATEX E 157 IECEx BVS II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex ta/tb IIIC T101 C Da/Db CIP SIP Electrical version 4-pin DC KAS A-K-22--Y5-StEx Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PEEK (FDA 21 CFR Accessories (not delivered with the sensor: For matching connectors please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

83 Ø 29,75 ±0,05 Ø25,5 Ø40 Series 80 - PNP - StEx - ATEX Type of construction F30 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 Special version with flange, double gasket for hole basis fitting Ø 30 mm. DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC KAS A-K-F30--StEx Art.-No. KA V DC 2 x ma Typ. 10 ma C Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 83

84 M 30 x1,5 Ø25,5 Ø40 Series 80 - PNP - StEx - ATEX Type of construction M 30 x 1.5 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db Electrical version 4-wire DC KAS A-K-M30--StEx Art.-No. KA V DC 2 x ma C Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

85 M 30 x1,5 Ø25,5 Ø40 Series 80 - PNP - StEx - ATEX Type of construction M 30 x 1.5 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC KAS A-K-M30--StEx Art.-No. KA V DC 2 x ma C Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 85

86 M30x1,5 Ø25,5 Ø40 SW36 M12x1 Series 80 - PNP - StEx - ATEX Type of construction M 30 x 1.5 For use in areas with the risk of dust explosion, zone 20 With flange connector M 12 x 1 DMT 01 ATEX E 157 IECEx BVS II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex ta/tb IIIC T101 C Da/Db Electrical version 4-pin DC KAS A-K-M30--Y5-StEx Art.-No. KA V DC 2 x ma C Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (delivered with the sensor Protective clip Accessories (not delivered with the sensor: For matching connectors please see our selection of accessories. *With sealed potentiometer screw All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

87 M30x1,5 Ø25,5 SW36 Ø40 M12x1 Series 80 - PNP - StEx - ATEX Type of construction M 30 x 1.5 For use in areas with the risk of dust explosion, zone 20 With flange connector M 12 x 1 DMT 01 ATEX E 157 IECEx BVS II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex ta/tb IIIC T101 C Da/Db All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC KAS A-K-M Y5-StEx Art.-No. KA V DC 2 x ma C Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (delivered with the sensor Protective clip Accessories (not delivered with the sensor: For matching connectors please see our selection of accessories. *With sealed potentiometer screw RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 87

88 Ø25,5 M32x1,5 Ø40 Series 80 - PNP - StEx - ATEX Type of construction M 32 x 1.5 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db Electrical version 4-wire DC KAS A-K-M32--StEx Art.-No. KA V DC 2 x ma C Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

89 Ø25,5 G1" SW36 Ø40 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC Type NPN KAS A-K-G1 --StEx Art.-No. KA 0824 Connection diagram No. 3 KAS A-K-G1 --StEx Art.-No. KA 0264 Connection diagram No V DC 2 x ma C Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 89

90 Ø25,5 G1" SW36 Ø40 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db Electrical version 4-wire DC KAS A-K-G1 --StEx Art.-No. KA V DC 2 x ma C Connection cable 5 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

91 Ø25,5 G1" SW36 Ø40 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC KAS A-K-G1 --StEx Art.-No. KA V DC 2 x ma C Connection cable 10 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 91

92 G1" Ø25,5 Ø40 M 12 x1 SW36 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 With flange connector M 12 x 1 DMT 01 ATEX E 157 IECEx BVS II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex ta/tb IIIC T101 C Da/Db Electrical version 4-pin DC KAS A-K-G1 --Y5-StEx Art.-No. KA V DC 2 x ma C Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (delivered with the sensor Protective clip Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

93 G1" Ø26 SW36 Ø40 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 Housing material: PEEK DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC KAS A-K-G1 -PEEK-StEx Art.-No. KA V DC 2 x ma C Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material PEEK (FDA 21 CFR Active surface PEEK (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories ,5 96,5 92,5 113 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 93

94 Ø25,5 G1" SW36 Ø40 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db Electrical version 4-wire DC KAS A-K-G StEx Art.-No. KA V DC 2 x ma C Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and protection Set M32 / # please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

95 Ø25,5 G1" Ø40 M 32 x1,5 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db All specifications are subject to change without notice. (04/2017 Electrical version 4-wire DC KAS A-K-G StEx Art.-No. KA V DC 2 x ma C Connection cable 5 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and protection Set M32 / # please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 95

96 Ø25,5 G1" Ø40 M12x1 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor With flange connector M 12 x 1 DMT 01 ATEX E 157 IECEx BVS II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex ta/tb IIIC T101 C Da/Db CIP SIP Electrical version 4-pin DC KAS A-K-G Y5-StEx Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (delivered with the sensor Protective clip Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories. *With sealed potentiometer screw All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

97 G1" Ø29,4 Ø25,4 Ø34 M 12 x1 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 Housing material: PEEK With flange connector M 12 x 1 DMT 01 ATEX E 157 IECEx BVS II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex ta/tb IIIC T101 C Da/Db All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC KAS A-G1-230-PEEK/VA-Y5-StEx Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material PEEK (FDA 21 CFR Active surface PEEK (FDA 21 CFR Lid PC (FDA 21 CFR VA No / AISI 303 Accessories (delivered with the sensor Protective clip Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories , ,5 229,5 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 10,5 97

98 Ø25,5 G1" Ø40 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db Electrical version 4-wire DC KAS A-K-G StEx Art.-No. KA V DC 2 x ma C Connection cable 5 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

99 G 1" Ø26 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor With flange connector M 12 x 1 DMT 01 ATEX E 157 IECEx BVS II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex ta/tb IIIC T101 C Da/Db All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC KAS A-K-G Y5-StEx Art.-No. KA V DC 2 x ma C Connection Connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories ,5 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de 99

100 G1" Ø30,2 Ø25,5 Ø40 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 Special version with flange. Sealing can be made with a gasket or -tape (not delivered with the sensor DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex mb IIC T4 Gb Ex ta/tb IIIC T101 C Da/Db Electrical version 4-wire DC KAS A-K-G StEx Art.-No. KA V DC 2 x ma C Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter and welding socket please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

101 Ø25,5 G1" Ø40 M12x1 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 With flange connector M 12 x 1 DMT 01 ATEX E 157 IECEx BVS II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex ta/tb IIIC T101 C Da/Db All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC KAS A-K-G Y5-StEx Art.-No. KA V DC 2 x ma C Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (delivered with the sensor Protective clip Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories. *With sealed potentiometer screw RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

102 Ø50 Ø25,5 Ø43,5 Ø34,7 Series 70 - NPN - StEx - ATEX Series 80 - PNP - StEx - ATEX Type of construction Triclamp DN 25 For use in areas with the risk of dust explosion, zone 20 For use in areas with the risk of gas explosion, zone 1 DMT 01 ATEX E 157 IECEx BVS II 2 G Ex mb IIC T4 Gb Ex mb IIC T4 Gb II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex ta/tb IIIC T101 C Da/Db Electrical version 4-wire DC Type NPN KAS A-K-Tri--StEx Art.-No. KA 1183 Connection diagram No. 3 KAS A-K-Tri--StEx Art.-No. KA 0421 Connection diagram No V DC 2 x ma C Connection cable 2 m, PVC, 4 x 0.5 mm² Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (not delivered with the sensor: Stainless steel welding nipple DN 25 # , Sealing gasket # , Triclamp mounting clamp # please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

103 Ø50 Ø43,5 Ø25,5 Ø34,7 M12x1 Series 80 - PNP - StEx - ATEX Type of construction Triclamp DN 25 For use in areas with the risk of dust explosion, zone 20 With flange connector M 12 x 1 DMT 01 ATEX E 157 IECEx BVS II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex ta/tb IIIC T101 C Da/Db All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC KAS A-K-Tri--Y5-StEx Art.-No. KA V DC 2 x ma C Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (delivered with the sensor Protective clip Accessories (not delivered with the sensor: Stainless steel welding nipple DN 25 # , Sealing gasket # , Triclamp mounting clamp # and matching connectors please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

104 G1" Ø29,4 Ø25,4 Ø30 M 12 x1 Series 80 - PNP - StEx - ATEX Type of construction G 1 For use in areas with the risk of dust explosion, zone 20 Housing material: PEEK With flange connector M 12 x 1 DMT 01 ATEX E 157 IECEx BVS II 1/2 D Ex ta/tb IIIC T101 C Da/Db Ex ta/tb IIIC T101 C Da/Db Electrical version 4-pin DC KAS A-K-G1 -PEEK-Y5-StEx Art.-No. KA V DC 2 x ma C Connection Flange connector M 12 x 1 Housing material PEEK (FDA 21 CFR Active surface PEEK (FDA 21 CFR Lid PC (FDA 21 CFR Accessories (delivered with the sensor Protective clip Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories. 56,7 44,2 41,2 35,2 6x17 112,7 13 All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

105 Ø22 Ø26 M12x1 Series 80 - PNP Type of construction Ø 22 mm For use in zone 22 With flange connector M 12 x 1 With manufacturer certificate II 3D Ex mc IIIC T101 C Dc IP67 X CIP SIP All specifications are subject to change without notice. (04/2017 Electrical version 4-pin DC KAS A-K-22--Y5-3D Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PEEK (FDA 21 CFR Accessories (not delivered with the sensor: For matching connectors please see our selection of accessories RECHNER Industrie-Elektronik GmbH Gaußstraße D Lampertheim Tel. Tel Fax Fax info@rechner-sensors.de

106 G1" Ø25,5 Ø40 M 12 x1 Series 80 - PNP Type of construction G 1 For use in zone 22 For use in areas where there is a risk of explosion With flange connector M 12 x 1 With manufacturer certificate II 3D Ex mc IIIC T101 C Dc IP67 X Electrical version 4-pin DC KAS A-K-G1 --Y5-3D Art.-No. KA V DC 2 x ma C / CIP 121 C (zero-current Connection Flange connector M 12 x 1 Housing material (FDA 21 CFR Active surface (FDA 21 CFR Lid PA Accessories (not delivered with the sensor: For varivent adapter, triclamp adapter, welding socket and matching connectors please see our selection of accessories All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

107 CAPACITIVE SENSORS KAS S26 LevelMaster Pages Capacitive sensors S26 body size G 1/ Capacitive sensors S26 body size G Capacitive sensors S26 body size G 3/8 115 All specifications are subject to change without notice. (04/2017 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

108 S26 - LEVELMASTER Capacitive Sensors - LevelMaster The capacitive sensors of the 700, 701 (NPN and 800, 801 (PNP type series are designed for the detection of liquids with a dielectric constant (DC εr of 1,25. For these sensors it is the dielectric constant of the product that is our focus of attention. For this reason it is important for the measurement that the active surface of the sensor (PEEK tip is in direct contact with the product that should be detected. The sensor tip must be totally immersed into the product. The Sensors are equipped with our well-tried EasyTeach Function. Both variants are available: ET = EasyTeach by buttom ETW = EasyTeach by wire With EasyTeach the sensitivity adjustment for the product to be detected is very easy and user-friendly. Capacitive sensors can activate directly electronic circuits, PLCs, relays or contactors. Application Example: The capacitive sensors of the type series 700 and 800 reliably detect the level or existence of liquids or pastes, in containers, tube systems or pipelines. Level- or limit value measurement in container Product control in tube systems or pipelines Drain protection of pumps A rich variety of products can be detected, for example: Vegetable oil, mineral oil Vinegar, alcohol, water, beer, syrup, fruit concentrate Ketchup, mayonnaise, mustard And a lot more. Accessories In our portfolio we have a range of FDA ing adapters and process connections. They ensure the hygienic installation and provide the possibility of impeccable cleaning and sterilisation. All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

109 G1/2" Ø18 Ø12,8 M 12 x1 - Model G 1/2 For level control of conductive and/or viscous liquids or pastes, for instance oil, water, ketchup or honey. Ideal for level control in the Food Industry or Pharmaceutical Industry Housing material: Stainless steel (VA Adjustment of the sensitivity with ETW- Function (EasyTeach by wire With flange connector M 12 x 1 Welding sockets and Varivent adapter available for EHEDG mounting. High Performance ETW EasyTeach Stainless Steel CIP SIP EHEDG 100 C 212 F High Temperature All specifications are subject to change without notice. (04/2017 Sensitivity Dielectric constant ε r > 1.25 Electrical version 3-pin DC Normally open Factory setting Water Typ PNP KS /84-S-G1/2-PEEK/VAb-Y3-ETW- Art. No. KA V DC ma Typ. < 30 ma 1 Hz C / CIP 121 C (zero-current Permitted product temperature C Green / orange Degree of protection IEC IP 67, IP 69K * Connection Connector M 12 x 1 Operating pressure Max. 10 bar Housing material Stainless steel VA No / AISI 303 Material active surface PEEK (FDA 21 CFR Material lid - Accessories (not supplied with the sensor: Varivent Adapter art.no , Welding Socket art.no and matching connectors please see our selection of accessories. *Where applicable 26,5 42,5 58, EasyTeachchart: as of 1,25. Liquids, like, juice, wine, chemicals or pharmaceutical Advantages: EHEDG Measurement is independent of the mounting position Permitted pressure on the active area: 10 bar RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de C PNP LED / Orange = A1 Green = A1 + - TEACH Factory reset Initializing Factory reset Adjustment full Initializing full Test

110 Ø30 Ø14 Ø18 Ø40 M12x1 - Model G 1/2 For level control of conductive and/or viscous liquids or pastes, for instance oil, water, ketchup or honey. Ideal for level control in the Food Industry or Pharmaceutical Industry Housing material: Stainless steel VA No / AISI 303 output (NO + NC EasyTeach-Function With flange connector M 12 x 1 High Performance ET EasyTeach Stainless Steel CIP SIP EHEDG 100 C 212 F High Temperature Sensitivity Dielectric constant ε r > 1.25 Electrical version 4-pin DC Type NPN KS /113-A-G1/2-PEEK/VAb-Y5-ET- Art. No. KA 1128 Connection diagram No. 1 Typ PNP KS /113-A-G1/2-PEEK/VAb-Y5-ET- Art. No. KA 1126 Connection diagram No V DC ma Typ. < 20 ma 1 Hz C / CIP 121 C (zero-current Permitted product temperature C Degree of protection IEC IP 67, IP 69K * Connection Connector M 12 x 1 Operating pressure Max. 10 bar Housing material Stainless steel VA No / AISI 303 Material active surface PEEK (FDA 21 CFR Material lid PA Accessories (not supplied with the sensor: Welding Socket and matching connectors please see our selection of accessories. *Where applicable G½" 15,8 10,8 45,8 32, EasyTeachchart: as of 1,25. Liquids, like, juice, wine, chemicals or pharmaceutical Advantages: Measurement is independent of the mounting position Permitted pressure on the active area: 10 bar 1 2 LED / Yellow = A1 Green = A2 Factory reset Initializing Factory reset Adjustment full Initializing full Test All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

111 Ø30 Ø14 Ø18 Ø40 M12x1 - Model G 1/2 For level control of conductive and/or viscous liquids or pastes, for instance oil, water, ketchup or honey. Ideal for level control in the Food Industry or Pharmaceutical Industry Housing material: Stainless steel VA No / AISI 303 output (NO + NC Adjustment of the sensitivity with ETW- Function (EasyTeach by wire With flange connector M 12 x 1 High Performance ETW EasyTeach Stainless Steel CIP SIP EHEDG 100 C 212 F High Temperature All specifications are subject to change without notice. (04/2017 Sensitivity Dielectric constant ε r > 1.25 Electrical version 4-pin DC Type NPN KS /113-A-G1/2-PEEK/VAb-Y10-ETW- Art. No. KA 1134 Connection diagram No. 1 Typ PNP KS /113-A-G1/2-PEEK/VAb-Y10-ETW- Art. No. KA 1130 Connection diagram No V DC ma Typ. < 20 ma 1 Hz C / CIP 121 C (zero-current Permitted product temperature C Degree of protection IEC IP 67, IP 69K * Connection Connector M 12 x 1 Operating pressure Max. 10 bar Housing material Stainless steel VA No / AISI 303 Material active surface PEEK (FDA 21 CFR Material lid PA Accessories (not supplied with the sensor: Welding Socket and matching connectors please see our selection of accessories. *Where applicable G½" 15,8 10,8 45,8 32, EasyTeachchart: as of 1,25. Liquids, like, juice, wine, chemicals or pharmaceutical Advantages: Measurement is independent of the mounting position Permitted pressure on the active area: 10 bar RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de LED / Yellow = A1 Green = A2 Factory reset Initializing Factory reset Adjustment full Initializing full Test

112 Ø14 Ø18 Ø40 M 12 x1 - Model G 1/2 For level control of conductive and/or viscous liquids or pastes, for instance oil, water, ketchup or honey. Ideal for level control in the Food Industry or Pharmaceutical Industry Housing material: Stainless steel VA No / AISI 303 output (NO + NC EasyTeach-Function With flange connector M 12 x 1 High Performance ET EasyTeach Stainless Steel CIP SIP EHEDG 100 C 212 F High Temperature *Where applicable 20,7 15,8 10, , Sensitivity Dielectric constant ε r > 1.25 Electrical version 4-pin DC Type NPN KS /113-A-G1-PEEK/Vab-Y5-ET- Art. No. KA 1129 Connection diagram No. 1 Typ PNP KS /113-A-G1-PEEK/VAb-Y5-ET- Art. No. KA 1127 Connection diagram No V DC ma Typ. < 20 ma 1 Hz C / CIP 121 C (zero-current Permitted product temperature C Degree of protection IEC IP 67, IP 69K * Connection Connector M 12 x 1 Operating pressure Max. 10 bar Housing material Stainless steel VA No / AISI 303 Material active surface PEEK (FDA 21 CFR Material lid PA Accessories (not supplied with the sensor: Varivent Adapter, Welding Socket and matching connectors please see our selection of accessories. EasyTeachchart: as of 1,25. Liquids, like, juice, wine, chemicals or pharmaceutical Advantages: Measurement is independent of the mounting position Permitted pressure on the active area: 10 bar 1 2 LED / Yellow = A1 Green = A2 Factory reset Initializing Factory reset Adjustment full Initializing full Test All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

113 Ø14 Ø18 Ø40 M 12 x1 - Model G 1 For level control of conductive and/or viscous liquids or pastes, for instance oil, water, ketchup or honey. Ideal for level control in the Food Industry or Pharmaceutical Industry Housing material: Stainless steel VA No / AISI 303 output (NO + NC Adjustment of the sensitivity with ETW- Function (EasyTeach by wire With flange connector M 12 x 1 High Performance ETW EasyTeach Stainless Steel CIP SIP EHEDG 100 C 212 F High Temperature All specifications are subject to change without notice. (04/2017 Sensitivity Dielectric constant ε r > 1.25 Electrical version 4-pin DC Type NPN KS /113-A-G1-PEEK/Vab-Y10-ETW- Art. No. KA 1131 Connection diagram No. 1 Typ PNP KS /113-A-G1-PEEK/VAb-Y10-ETW- Art. No. KA 1135 Connection diagram No V DC ma Typ. < 20 ma 1 Hz C / CIP 121 C (zero-current Permitted product temperature C Degree of protection IEC IP 67, IP 69K * Connection Connector M 12 x 1 Operating pressure Max. 10 bar Housing material Stainless steel VA No / AISI 303 Material active surface PEEK (FDA 21 CFR Material lid PA Accessories (not supplied with the sensor: Varivent Adapter, Welding Socket and matching connectors please see our selection of accessories. *Where applicable 20,7 15,8 10, , EasyTeachchart: as of 1,25. Liquids, like, juice, wine, chemicals or pharmaceutical Advantages: Measurement is independent of the mounting position Permitted pressure on the active area: 10 bar RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de LED / Yellow = A1 Green = A2 Factory reset Initializing Factory reset Adjustment full Initializing full Test

114 Ø14 Ø18 Ø40 M 12 x1 - Model G 1 For level control of conductive and/or viscous liquids or pastes, for instance oil, water, ketchup or honey. Ideal for level control in the Food Industry or Pharmaceutical Industry Housing material: Stainless steel VA No / AISI x Normally open output for independent switching points Adjustment of the sensitivity with ETW- Function (EasyTeach by wire With flange connector M 12 x 1 High Performance ETW EasyTeach Stainless Steel CIP SIP EHEDG 100 C 212 F High Temperature Sensitivity Dielectric constant ε r > 1.25 Electrical version 4-pin DC 2 x Normally open Typ PNP KS /113-S-G1-PEEK/VAb-Y10-ETW-E- Art. No. KA V DC ma Typ. < 20 ma 1 Hz C / CIP 121 C (zero-current Permitted product temperature C Degree of protection IEC IP 67, IP 69K * Connection Connector M 12 x 1 Operating pressure Max. 10 bar Housing material Stainless steel VA No / AISI 303 Material active surface PEEK (FDA 21 CFR Material lid PA Accessories (not supplied with the sensor: Varivent Adapter, Welding Socket and matching connectors please see our selection of accessories. *Where applicable 20,7 15,8 10, , EasyTeachchart: as of 1,25. Liquids, like, juice, wine, chemicals or pharmaceutical Advantages: Measurement is independent of the mounting position Permitted pressure on the active area: 10 bar LED / Yellow = A1 Green = A2 Factory reset Initializing Factory reset Adjustment full Initializing full Test All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

115 Ø14,8 Ø14 Ø40 M12x1 - Model G 3/8 For level control of conductive and/or viscous liquids or pastes, for instance oil, water, ketchup or honey. Ideal for level control in the Food Industry or Pharmaceutical Industry Housing material: Stainless steel VA No / AISI 303 output (NO + NC EasyTeach-Function With flange connector M 12 x 1 High Performance ET EasyTeach Stainless Steel CIP SIP EHEDG 100 C 212 F High Temperature All specifications are subject to change without notice. (04/2017 *Where applicable 10, ,8 44,5 32, ,8 40 Sensitivity Dielectric constant ε r > 1.25 Electrical version 4-pin DC Typ PNP KS /113-A-G3/8-PEEK/VAb-Y5-ET- Art. No. KA V DC ma Typ. < 20 ma 1 Hz C / CIP 121 C (zero-current Permitted product temperature C Degree of protection IEC IP 67, IP 69K * Connection Connector M 12 x 1 Operating pressure Max. 10 bar Housing material Stainless steel VA No / AISI 303 Material active surface PEEK (FDA 21 CFR Material lid PA Accessories (not supplied with the sensor: For matching connectors please see our selection of accessories. EasyTeachchart: as of 1,25. Liquids, like, juice, wine, chemicals or pharmaceutical Advantages: Measurement is independent of the mounting position Permitted pressure on the active area: 10 bar LED / Yellow = A1 Green = A2 Factory reset Initializing Factory reset Adjustment full Initializing full Test RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

116 116 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax All specifications are subject to change without notice. (04/2017

117 type selection in article number order All specifications are subject to change without notice. (04/2017 Art. No. Description Page KAS-80-26/113-A-G1--Z KA0264 KAS A-K-G1 --StEx 89 KA0266 KAS-80-26/113-A-G1--Z KA0277 KAS-80-26/113-A-G1--100C-Z KA0409 KAS-90-26/113-S-G1--Z KA0415 KAS-80-26/113-A-TRI--100C-Z KA0421 KAS A-K-Tri--StEx 102 KA0423 KAS-80-26/200-A-G1--Z KA0431 KAS-80-26/113-A-M22--Z03-1-E- 26 KA0444 KAS A-K-G StEx 94 KA0450 KAS-80-26/113-A-D C-Y KA0549 KAS-80-26/113-A-PFS1--Y KA0566 KAS-80-26/113-A-PFS2--Z KA0620 KAS-80-26/113-A-PFS1--Z KA0626 KAS-80-26/113-A-F C-Y KA0636 KAS-80-26/F30-A-K--StEx 83 KA0639 KAS-90-26/113-S-G1--Y KA0642 KAS-80-26/113-A-G1--Y KA0653 KAS-80-26/200-A-G1--Z KA0655 KAS A-K-G1 --Y5-StEx 92 KA0656 KAS-80-26/113-A-TRI--100C-Y5-1-E- 58 KA0659 KAS A-K-G1 --Y5-3D 106 KA0662 KAS-80-26/113-A-TRI--100C-Y KA0682 KAS-80-26/300-A-G1--Y KA0683 KAS-90-26/113-Ö-TRI--Z KA0684 KAS-90-26/113-S-TRI--Z KA0685 KAS-90-26/113-Ö-G1--Z KA0686 KAS-80-26/200-A-G1--Y KA0687 KAS-80-26/200-A-G1--100C-Y KA0688 KAS-80-26/113-A-G1--100C-Y KA0689 KAS-80-26/113-A-M30--Y KA0694 KAS-80-26/113-A-D C-Y KA0740 KAS N-K-G1-72 KA0764 KAS-80-26/113-A-G1-PEEK-Y5-1-E- 63 KA0767 KAS A-K-G1 -PEEK-Y5-StEx 104 KA0795 KAS A-K-G StEx 100 KA0821 KAS-80-26/113-A-G1--120C-Z02-1-NL 44 KA0824 KAS A-K-G1 --StEx 89 KA0829 KAS A-K-Tri--Y5-StEx 103 KA0837 KAS A-K-G1 --StEx, 5 m 90 KA0843 KAS-80-26/200-A-G1--Z KA0844 KAS-70-26/113-A-G1--Y KA0861 KAS A-G1-230-PEEK/VA-Y5-StEx 97 KA0872 KAS-80-26/113-A-G1-PP-Z02-1-NL 40 KA0933 KAS N-K-G1 --StEx 76 KA0939 KAS-80-26/113-A-F C-Y10-ETW- 28 KA0971 KAS-90-26/113-S-M30-PP-Z02-1-NL 65 KA0981 KAS A-K-G Y5-StEx 96 KA0984 KAS-80-26/113-A-G1--Z02-ETW- 36 KA0991 KAS-90-26/113-S-G1--Z KA0996 KAS-80-26/113-A-G1--Z02-ET-E- 35 KA0998 KAS A-K-M32--StEx 88 KA1013 KAS-90-26/113-Ö-G1--Y KA1025 KAS-70-26/113-A-TRI--100C-Z KA1037 KAS-80-26/113-A-M30--Z03-ETW- 30 KA1038 KAS-80-26/113-A-PFM30--Z03-ETW- 59 KA1078 KAS-70-26/113-A-G1--Z KA1084 KAS-80-26/113-A-G1--Z02-ET- 34 KA1091 KAS-80-26/113-A-G3/4--Z KA1097 KAS-80-26/113-A-G1--Y10-ETW- 38 KA1126 KS /113-A-G1/2-PEEK/VAb-Y5-ET- 110 KA1127 KS /113-A-G1-PEEK/VAb-Y5-ET- 112 KA1128 KS /113-A-G1/2-PEEK/VAb-Y5-ET- 110 KA1129 KS /113-A-G1-PEEK/Vab-Y5-ET- 112 KA1130 KS /113-A-G1/2-PEEK/VAb-Y10-ETW- 111 KA1131 KS /113-A-G1-PEEK/Vab-Y10-ETW- 113 KA1134 KS /113-A-G1/2-PEEK/VAb-Y10-ETW- 111 Art. No. Description Page KA1135 KS /113-A-G1-PEEK/VAb-Y10-ETW- 113 KA1164 KAS A-K-G1 --StEx, 10 m 91 KA1180 KAS A-K-G StEx 98 KA1183 KAS A-K-Tri--StEx 102 KA1190 KAS N-K-G1 --StEx, 5 m 77 KA1214 KAS-80-26/113-A-TRI--100C-Y5-ET- 57 KA1216 KAS N-K-G Y5-StEx 79 KA1228 KAS A-K-G Y5-StEx 101 KA1230 KAS N-K-G C 73 KA1231 KAS N-K-G Y5-StEx 78 KA1236 KAS-80-26/113-Ö-G1--100C-Y KA1243 KS /113-S-G1-PEEK/VAb-Y10-ETW-E- 114 KA1244 KAS A-K-G1/2-PEEK 22 KA1245 KAS A-K-G1/2-PEEK 22 KA1253 KAS A-K-G StEx, 5 m 95 KA1255 KAS-80-26/200-A-G1--Z02-ET- 49 KA1262 KAS A-K-M30--StEx 84 KA1265 KS /113-A-G3/8-PEEK/VAb-Y5-ET- 115 KA1279 KAS A-K-G Y5-StEx 99 KA1280 KAS A-K-M Y5-StEx 87 KA1281 KAS A-K-M30--Y5-StEx 86 KA1282 KAS A-K-G1/2-PEEK-ETW 23 KA1287 KAS-70-26/200-A-G1--Z KA1294 KAS-80-26/416-A-G1-PP/VAc-Z02-ETW- 53 KA1365 KAS A-K-M30--StEx 85 KA1366 KAS A-K-22--Y5-3D 105 KA1375 KAS-80-26/416-A-G1-PP/VAc-Y10-ETW- 54 KA1389 KAS N-K-M30--StEx 75 KA1392 KAS-80-26/113-A-G1-PEEK-Y10-ETW- 39 KA1395 KAS A-K-G1 -PEEK-StEx 93 KA1403 KAS-80-26/113-A-G1--Z02-BS- 33 KA1409 KAS A-K-160-G1/2 -PEEK-StEx 81 KA1410 KAS N-K-PFM22--StEx 74 KA1413 KAS A-K-22--Y5-StEx 82 KA1426 KAS A-K-G1/2 -PEEK-StEx 80 KA1437 KKS /98-S-G1/2-PEEK/VAb-Y3-ETW- 109 KA1441 KAS-80-26/150-A-G1--180C-Z RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

118 Type selection in description order Art. No. Description Page KA1216 KAS N-K-G Y5-StEx 79 KA1231 KAS N-K-G Y5-StEx 78 KA0740 KAS N-K-G1-72 KA1230 KAS N-K-G C 73 KA0933 KAS N-K-G1 --StEx 76 KA1190 KAS N-K-G1 --StEx, 5 m 77 KA1389 KAS N-K-M30--StEx 75 KA1410 KAS N-K-PFM22--StEx 74 KA0844 KAS-70-26/113-A-G1--Y KA1078 KAS-70-26/113-A-G1--Z KA1025 KAS-70-26/113-A-TRI--100C-Z KA1287 KAS-70-26/200-A-G1--Z KA1245 KAS A-K-G1/2-PEEK 22 KA0824 KAS A-K-G1 --StEx 89 KA1183 KAS A-K-Tri--StEx 102 KA0450 KAS-80-26/113-A-D C-Y KA0694 KAS-80-26/113-A-D C-Y KA0939 KAS-80-26/113-A-F C-Y10-ETW- 28 KA0626 KAS-80-26/113-A-F C-Y KA1392 KAS-80-26/113-A-G1-PEEK-Y10-ETW- 39 KA0764 KAS-80-26/113-A-G1-PEEK-Y5-1-E- 63 KA0872 KAS-80-26/113-A-G1-PP-Z02-1-NL 40 KA0688 KAS-80-26/113-A-G1--100C-Y KA0277 KAS-80-26/113-A-G1--100C-Z KA0821 KAS-80-26/113-A-G1--120C-Z02-1-NL 44 KA1097 KAS-80-26/113-A-G1--Y10-ETW- 38 KA0642 KAS-80-26/113-A-G1--Y KAS-80-26/113-A-G1--Z KA1403 KAS-80-26/113-A-G1--Z02-BS- 33 KA0996 KAS-80-26/113-A-G1--Z02-ET-E- 35 KA1084 KAS-80-26/113-A-G1--Z02-ET- 34 KA0984 KAS-80-26/113-A-G1--Z02-ETW- 36 KA0266 KAS-80-26/113-A-G1--Z KA1091 KAS-80-26/113-A-G3/4--Z KA0431 KAS-80-26/113-A-M22--Z03-1-E- 26 KA0689 KAS-80-26/113-A-M30--Y KA1037 KAS-80-26/113-A-M30--Z03-ETW- 30 KA1038 KAS-80-26/113-A-PFM30--Z03-ETW- 59 KA0549 KAS-80-26/113-A-PFS1--Y KA0620 KAS-80-26/113-A-PFS1--Z KA0566 KAS-80-26/113-A-PFS2--Z KA0656 KAS-80-26/113-A-TRI--100C-Y5-1-E- 58 KA0662 KAS-80-26/113-A-TRI--100C-Y KA1214 KAS-80-26/113-A-TRI--100C-Y5-ET- 57 KA0415 KAS-80-26/113-A-TRI--100C-Z KA1236 KAS-80-26/113-Ö-G1--100C-Y KA1441 KAS-80-26/150-A-G1--180C-Z KA0687 KAS-80-26/200-A-G1--100C-Y KA0686 KAS-80-26/200-A-G1--Y KA0653 KAS-80-26/200-A-G1--Z KA1255 KAS-80-26/200-A-G1--Z02-ET- 49 KA0423 KAS-80-26/200-A-G1--Z KA0843 KAS-80-26/200-A-G1--Z KA0682 KAS-80-26/300-A-G1--Y KA1375 KAS-80-26/416-A-G1-PP/VAc-Y10-ETW- 54 KA1294 KAS-80-26/416-A-G1-PP/VAc-Z02-ETW- 53 KA0636 KAS-80-26/F30-A-K--StEx 83 KA0861 KAS A-G1-230-PEEK/VA-Y5-StEx 97 KA1409 KAS A-K-160-G1/2 -PEEK-StEx 81 KA1366 KAS A-K-22--Y5-3D 105 KA1413 KAS A-K-22--Y5-StEx 82 KA1426 KAS A-K-G1/2 -PEEK-StEx 80 KA1244 KAS A-K-G1/2-PEEK 22 KA1282 KAS A-K-G1/2-PEEK-ETW 23 KA0444 KAS A-K-G StEx 94 KA1253 KAS A-K-G StEx, 5 m 95 KA0981 KAS A-K-G Y5-StEx 96 Art. No. Description Page KA1180 KAS A-K-G StEx 98 KA1279 KAS A-K-G Y5-StEx 99 KA0795 KAS A-K-G StEx 100 KA1228 KAS A-K-G Y5-StEx 101 KA1395 KAS A-K-G1 -PEEK-StEx 93 KA0767 KAS A-K-G1 -PEEK-Y5-StEx 104 KA0264 KAS A-K-G1 --StEx 89 KA1164 KAS A-K-G1 --StEx, 10 m 91 KA0837 KAS A-K-G1 --StEx, 5 m 90 KA0659 KAS A-K-G1 --Y5-3D 106 KA0655 KAS A-K-G1 --Y5-StEx 92 KA1280 KAS A-K-M Y5-StEx 87 KA1262 KAS A-K-M30--StEx 84 KA1365 KAS A-K-M30--StEx 85 KA1281 KAS A-K-M30--Y5-StEx 86 KA0998 KAS A-K-M32--StEx 88 KA0421 KAS A-K-Tri--StEx 102 KA0829 KAS A-K-Tri--Y5-StEx 103 KA1013 KAS-90-26/113-Ö-G1--Y KA0685 KAS-90-26/113-Ö-G1--Z KA0683 KAS-90-26/113-Ö-TRI--Z KA0639 KAS-90-26/113-S-G1--Y KA0409 KAS-90-26/113-S-G1--Z KA0991 KAS-90-26/113-S-G1--Z KA0971 KAS-90-26/113-S-M30-PP-Z02-1-NL 65 KA0684 KAS-90-26/113-S-TRI--Z KA1437 KKS /98-S-G1/2-PEEK/VAb-Y3-ETW- 109 KA1134 KS /113-A-G1/2-PEEK/VAb-Y10-ETW- 111 KA1128 KS /113-A-G1/2-PEEK/VAb-Y5-ET- 110 KA1131 KS /113-A-G1-PEEK/Vab-Y10-ETW- 113 KA1129 KS /113-A-G1-PEEK/Vab-Y5-ET- 112 KA1130 KS /113-A-G1/2-PEEK/VAb-Y10-ETW- 111 KA1126 KS /113-A-G1/2-PEEK/VAb-Y5-ET- 110 KA1135 KS /113-A-G1-PEEK/VAb-Y10-ETW- 113 KA1127 KS /113-A-G1-PEEK/VAb-Y5-ET- 112 KA1265 KS /113-A-G3/8-PEEK/VAb-Y5-ET- 115 KA1243 KS /113-S-G1-PEEK/VAb-Y10-ETW-E- 114 All specifications are subject to change without notice. (04/ RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de

119 Customer proximity guaranteed! Rechner Sensors has daughter and sister companies in China, Great Britain, Italy, Canada, South Korea and in the U.S.. Furthermore we have representative offices in over 50 countries. For the addresses of our sales partners please visit our website. You will find the addresses under the category contact. Canada GREAT BRITAIN ITALY People s Republic of China Rechner Automation Inc 348 Bronte St. South - Unit 11 Milton, ON L9T 5B6 Tel Fax contact@rechner.com Rechner (UK Limited Unit 6, The Old Mill 61 Reading Road Pangbourne, Berks, RG8 7HY Tel Fax info@rechner-sensors.co.uk Rechner Italia SRL Via Isarco Bolzano (BZ Office: Via Guelfa Bologna Tel Fax info@rechneritalia.it Rechner Sensors SIP Co.Ltd. Building H, No. 58, Yang Dong Road Suzhou Industrial Park Jiangsu Province Tel Fax assist@rechner-sensor.cn Republic of Korea (South United States of America Rechner-Korea Co. Ltd. A-1408 Ho, Keumgang Penterium IT Tower, Hakeuiro 282, Dongan-gu Anyang City, Gyunggi-do, Seoul Rechner Electronics Ind. Inc Inducon Corporate Drive, Suite 5 Sanborn, NY Tel Fax sensor@rechner.co.kr Tel Fax contact@rechner.com All specifications are subject to change without notice. (04/2017 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D Lampertheim Tel Fax info@rechner-sensors.de