Slot / Connector Type

Transcription

1 Photomicrosensor (Transmissive) EE-SX316/3163/3164-P Series EE-SX416/4163/4164-P Series EE-00 1M Slot / Connector Type Photo IC output ( / Light N) Connector with strong lock manufactured by JST. Mates with HR-03. Mounted with M screws Models available for - or 1- power supply. Zener diode mounted for greater noise immunity ( and -Z only). Connector with cable (rder Separately) is available. EE-00 1M (Refer to page.) Be sure to read Safety Precautions on page 3. Features Models with Connectors Eliminate the Need for a Separate PCB ll-in-ne Structure Facilitates Downsizing Models vailable for Mounting on X, Y, and Z xes Models with connectors are available with different mounting directions. Photomicro sensor No PCB designing! Enables downsizing! Control PCB xis X xis Z xis Y pplication ffice utomation Equipment (Copier, Printer) musement Equipment Home ppliances (ir Cleaner) ending Machine, TM 1

2 EE-SX316/3163/3164-P Series EE-SX416/4163/4164-P Series EE-00 1M rdering Information Photomicrosensor ppearance Sensing method Connecting method Sensing distance perture size (H W) (mm) type Power supply configuration Model Side mounting DC -Z 13 L-shaped mounting Transmissive (slot type) Connector mm (Slot width) Emitter 1.4 x 1.4 Detector 1.4 x 0. Photo IC DC 1 DC DC Horizontal mounting 14 1 DC.6 DC Ratings, Characteristics and Exterior Specifications bsolute Maximum Ratings (Ta = C) Item Power supply current Permissible output dissipation perating temperature Storage temperature Symbol -Z Rated value * Even if the specified conditions are met, perform derating of the and current as required by the temperature rating diagram. lso, do not expose the product to freezing or condensation. Exterior Specifications ppearance Item Connecting method Unit Remarks CC 13. DC. DC UT 13. IUT 16 m PUT 80 mw * Topr -0 to +8 C * Tstg -30 to +8 C * Side mounting -Z L-shaped mounting Connector Horizontal mounting Electrical and ptical Characteristics (Ta = C) Item Power supply Current consumption Low-level output High-level output Response frequency Symbol *1. The value of the response frequency is measured by rotating the disk as shown below. 0. mm Dark- N Light- N *. nly with models ending in -Z. Rated value 1 DC model DC model -Z CC 10.8 to 13.DC 4. to. DC ICC L H f 0. mm.1 mm m max. (With and without incident) 0.3 max. (IUT=16 m) (: without incident, : with incident) (CC 0.9 max. (UT=CC, RL=47 kω)) (: with incident, : without incident) 3 khz min. (UT=CC, IUT=16 m * 1) 1 khz min. (UT=CC, IUT=16 m * 1, * ) Disk Weight pprox. 1. g pprox.1.4 g pprox. 1.1 g Material Case Emitter and receiver sections Polybutylene terephthalate (PBT) Polyphenylene sulfide (PPS)

3 EE-SX316/3163/3164-P Series EE-SX416/4163/4164-P Series EE-00 1M Engineering Data (Reference value) Fig 1. llowable Dissipation vs. mbient Temperature Characteristics Fig. Sensing Position Characteristics (Typical) Fig 3. Sensing Position Characteristics (Typical) 100 allowable dissipation Pout (mw) mbient temperature Ta ( C) N FF transistor ( ) FF (N) -3 d1 = 0±0.3 mm CC = 1 Ta = C RL = 47 kω Distance d (mm) d1 (Center of axis) d Light interrupting plate FF (High) transistor N (Low) -3 d = 0±0.7 mm CC = 1 Ta = C RL = 47 kω Distance d (mm) d d (Center of axis) Safety Precautions To ensure safe operation, be sure to read and follow the Instruction Manual provided with the Sensor. CUTIN This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. Precautions for Correct Use Do not use the product in atmospheres or environments that exceed product ratings. Dispose of this product as industrial waste. Precautions for Safe Use Do not use the product with a or current that exceeds the rated range. pplying a or current that is higher than the rated range may result in explosion or fire. Do not miswire such as the polarity of the power supply. therwise the product may be damaged or it may burn. Do not short-circuit the load. therwise explosion or burning may occur. This product does not resist water. Do not use the product in places where water or oil may be sprayed onto the product. 3

4 EE-SX316/3163/3164-P Series EE-SX416/4163/4164-P Series EE-00 1M Dimensions and Internal Circuit Photomicrosensor (Unit: mm) -Z Marked surface (brand, model number, and lot) ptical axis perture width (4.) (14) 1.4. dia. -R1. perture size (H W) (7) Cross section view - (Detector side) Emitter Detector Internal Circuit Manufactured by JST Note: nly with models ending in -Z. (3) () (1) Recommended Mating Connectors: JST (Japan Solderless Terminal) HR-03 Unless otherwise specified, the tolerances are as shown below. Terminal No. Name (1) round (ND) () (UT) (3) Power supply (CC) Dimensions Tolerance 3 mm max. ±0. 3 < mm 6 ±0.4 6 < mm 10 ± < mm 18 ± < mm 30 ±0.4 Note: Dimensions in parentheses are for reference only. -R dia. (6.6) perture size (H W) Emitter Detector Manufactured by JST (3) () (1) (13.) ptical axis Marked surface (brand, model number, and lot) Recommended Mating Connectors: JST (Japan Solderless Terminal) HR perture width 1.4 Cross section view - (Detector side) Internal Circuit Terminal No. Name (1) round (ND) () (UT) (3) Power supply (CC) Unless otherwise specified, the tolerances are as shown below. Dimensions Tolerance 3 mm max. ±0. 3 < mm 6 ±0.4 6 < mm 10 ± < mm 18 ± < mm 30 ±0.4 Note: Dimensions in parentheses are for reference only. 4

5 EE-SX316/3163/3164-P Series EE-SX416/4163/4164-P Series EE-00 1M (4.1) perture size (H W) Emitter Detector ptical axis (14) (8.) Marked surface (brand, model number, and lot) perture width 0.. dia. (7) -R1. Cross section view (Detector side) (1) () (3) Internal Circuit Manufactured by JST Recommended Mating Connectors: JST (Japan Solderless Terminal) HR-03 Unless otherwise specified, the tolerances are as shown below. Terminal No. Name Dimensions Tolerance (1) round (ND) 3 mm max. ±0. () (UT) 3 < mm 6 ±0.4 (3) Power supply (CC) 6 < mm 10 ± < mm 18 ± < mm 30 ±0.4 Note: Dimensions in parentheses are for reference only. Connector with cable (rder Separately) EE-00 1M (1) () 1,000 ±10 (3) 3 ± No. Name (1) Connector, HS for harness () Connector, CT for harness (3) Lead wires Wiring Model/ Specifications Quantity Manufacturer HR-03-S 1 JST SSHL-00TP0. 3 JST UL1061 W6 Connector circuit number Lead-wire color 1 Blue Black 3 Brown 3

6 pplication examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product. Consult your MRN representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or equipment, and be sure to provide the system or equipment with double safety mechanisms. Note: Do not use this document to operate the Unit. MRN Corporation Electronic and Mechanical Components Company Contact: Cat. No. E460-E (1016)()