(HALT & HASS) Helping to reduce time to market and improve cost efficiency
|
|
- Cassandra Bell
- 6 years ago
- Views:
Transcription
1 Highly Accelerated Life Tests and Highly Accelerated Stress Screens (HALT & HASS) Helping to reduce time to market and improve cost efficiency Chris Bowles TÜV Product Service Tel: +44 (0) TÜV SÜD Product Service GmbH 1
2 What is HALT / HASS? HALT (Highly Accelerated Life Test) and HASS (Highly Accelerated Stress Screen) are recognised as powerful tools for improving product reliability, reducing time to market, reducing warranty costs and increasing customer satisfaction. TÜV SÜD Product Service GmbH 2
3 HALT HALT (Highly Accelerated Life Test) TÜV SÜD Product Service GmbH Hari Mountogianakis
4 HALT In HALT the goal is to over stress the product, induce failures and improve reliability. After uncovering and understanding the failure modes, corrective action can be taken to push out the operating limits of the product as far as possible. A HALT is performed in the early stages of the design progress. HALT is not a test to pass or fail. It is a process of discovery and design optimization. TÜV SÜD Product Service GmbH Hari Mountogianakis
5 HALT Although the failure modes are induced by overstresses, they are typically valid failure modes that would show up in the field. HALT determines the weakest parts in the design of the product. The overstresses applied, are accelerating the precipitation of these failures and allow an early correction in only 3 to 5 days. HALT is the opportunity to find most, if not all of the failures that would show up in qualification testing (often even more). TÜV SÜD Product Service GmbH 5
6 The HALT Environment The stresses applied during HALT are thermal extremes, rapid thermal transitions, vibration, and a combination of thermal and vibration stress. Low temperature step stress. High temperature step stress Rapid thermal cycles Vibration step stress Combined environment cycles TÜV SÜD Product Service GmbH 6
7 The HALT Environment Low temperature step stress TÜV SÜD Product Service GmbH Hari Mountogianakis
8 The HALT Environment High Temperature Step Stress TÜV SÜD Product Service GmbH Hari Mountogianakis
9 Temperature ( C) The HALT Environment Rapid Thermal Cycles 90 Rapid Thermal Cycles Time Elapsed TÜV SÜD Product Service GmbH Hari Mountogianakis
10 The HALT Environment Vibration Step Stress TÜV SÜD Product Service GmbH Hari Mountogianakis
11 The HALT Environment The vibration system is utilises repetitive shock hammers, exiting 6 DOF over a wide bandwidth (2Hz to 10kHz). Vibration in Six Degrees Of Freedom (6DOF) TÜV SÜD Product Service GmbH Hari Mountogianakis
12 Temperature ( C) The HALT Environment Combined Environment Cycles Combined Environment Cycles Vibration (g rms) Time Elapsed TÜV SÜD Product Service GmbH Hari Mountogianakis
13 Typical HALT Failures High/ Low temperature: Marginal components/design and process issues. Thermal Cycles: Thermal coefficient of expansion mismatches, weak solder joints, PCB mounting problems. Vibration: Weak solder joints, poor PCB design, poor component mounting. Combined: All of the above TÜV SÜD Product Service GmbH Hari Mountogianakis
14 HALT Equipment Stress In addition to the HALT environment the equipment under test must be function checked and stressed. Voltage margining Power cycling Frequency changes Clock variations TÜV SÜD Product Service GmbH Hari Mountogianakis
15 Preparing for HALT Sample size is typically 4 to 6 units allowing detailed verification of the failure modes found and insure that no failure mode is missed. A critical factor during HALT is a high resolution monitoring with functional test equipment. It must ensure that relevant functions and signals can be monitored, diagnosed as well as stimulated. Prior to HALT equipment coverings and enclosures may be modified to aid airflow. TÜV SÜD Product Service GmbH 15
16 Preparing for HALT Prepare the correct personnel for the HALT team. It is not advisable to test a complex product with a lot of sub assemblies simultaneously. An ideal HALT on a complex product includes testing of all subassemblies and finally the complete product in a final HALT. TÜV SÜD Product Service GmbH Hari Mountogianakis
17 The HALT Discovery Process The philosophy of HALT is to eliminate the responsible failure modes for operating and destruct limits and to push them further and further out. Maximizing your margins increases your product s life, robustness and reliability. The following diagram shows the graphical presentation of these limits. TÜV SÜD Product Service GmbH 17
18 The HALT Discovery Process Operating and Destruction limit of a product before HALT TÜV SÜD Product Service GmbH 18
19 The HALT Discovery Process The figure helps to understand the HALT technique. For example if a high ripple of the power supply is detected and hundreds of units were tested, the distribution of this failure mode would be as shown on the graph. By increasing the stress until the failure is uncovered, it will be detected during HALT. If the tail of this distribution falls into the operating specifications, the failure mode exists in some of your delivered products. TÜV SÜD Product Service GmbH Hari Mountogianakis
20 The HALT Discovery Process Operating and Destruction limit of a product after HALT Lower Destruct Limit Lower Operating Limit Product Specification Upper Operating Limit Lower Operating Limit Operating margin Destruct margin TÜV SÜD Product Service GmbH 20
21 The HALT Discovery Process When the tails are well outside the product specifications, the product ages (fatigue process of all components and parts) and the limits drift and begin to creep into the Specification Limits. Pushing out the stresses until a failure mode occurs, secures a highly accelerated aging, and precipitates failure modes in just a few days, instead of months until they occur in the field. TÜV SÜD Product Service GmbH 21
22 The HALT Discovery Process A root cause failure analysis ensures that failure modes are understood and the failure distribution will never have a tail inside product specifications and will never shift over a time or fatigue. There are two stopping points. Either the limit of the test equipment or the fundamental limits of the technology. After a Root Cause Failure Analysis, you have a clear understanding of the limits and margins of your product and you will know why the failures occur. TÜV SÜD Product Service GmbH Hari Mountogianakis
23 Benefits of HALT Early detection of latent faults Huge savings in warranty costs Reduced time to market Increased reliability Increased customer satisfaction TÜV SÜD Product Service GmbH 23
24 HASS HASS (Highly Accelerated Stress Screen) TÜV SÜD Product Service GmbH 24
25 HASS HASS is a production screen test that is used to make sure that the limits of a product determined in HALT were not decreased after the production. Deliverable units are used. HASS can catch and uncover these failures and verifies that no new weak links have been introduced during production. To design a HASS profile, HALT is absolutely recommended. The Operational and Destruct Limits found there are the basis. During HASS the Combined Environmental Stresses are applied. TÜV SÜD Product Service GmbH 25
26 HASS Typically HASS limits are set to 50% of the vibration limit and 80% of the temperature limits found in HALT. Prior to running a HASS program a HASS proof of screen is run. The HASS proof of screen ensures that no more than 5% of useful life is removed from the product. TÜV SÜD Product Service GmbH 26
27 Benefits of HASS Assures manufacturing process and workmanship integrity. Identify and preclude escape of potentially early life product failures. Detect and correct component variation. Decrease field service and warranty costs. TÜV SÜD Product Service GmbH 27
28 Summary After a clear understanding of the goals in HALT and HASS, this test technique and philosophy gives you the opportunity to identify possible defects contained in your product, at an early point during the design. If executed in a clear and carefully way, the result will be a robust product with increased lifetime and reliability, reduced warranty issues and delighted and satisfied customers. TÜV SÜD Product Service GmbH 28
29 HALT and HASS Thank you TÜV SÜD Product Service GmbH 29
Reliability Qualification Report
Reliability Qualification Report Voltage Controlled Oscillators (VCOs) Phase-Locked Loops (PLL) Products Qualified All VCO Modules in T Packages All VCO Modules in U Packages All VCO Modules in K Packages
More informationQUALITY ASSURANCE FOR SPACE INSTRUMENTS BUILT WITH COTS
QUALITY ASSURANCE FOR SPACE INSTRUMENTS BUILT WITH COTS Peter Buch Guldager, Gøsta G. Thuesen, John Leif Jørgensen ØRSTED*DTU, Measurement and Instrumentation Systems, Building 327, Technical University
More informationStress for SuccESS TM. Environmental Stress Screening Systems for Accelerated Product Development and Production Testing
TM Stress for SuccESS TM Environmental Stress Screening Systems for Accelerated Product Development and Production Testing Q & A What common approach has allowed industry leading manufacturers to maximize
More informationInertial Measurement Unit (IMU) ISIS-IMU (Rev. C)
Inertial Measurement Unit (IMU) ISIS-IMU (Rev. C) Features Fully compensated Inertial Measurement Unit (IMU) DC in digital output Most cost effective IMU - Lowest cost 6 degree of freedom IMU in its performance
More informationAPPLICATION NOTES. Wire Gauge and Distance to Load
The RB, RW and RM series of power supplies were designed as military grade, stand alone devices requiring no external components for operation. The entire series are 60 to 200 khz, fixed frequency, switching
More informationGrayhill, Inc. La Grange, IL
Device Under Test: 62SY15045 Physical Test: Dimensional, Mechanical Vibration, Mechanical Shock Electrical Test: Contact Resistance, Thermal Shock Test Report Number: SP02-1875 Test Start Date: January
More informationPRODUCT SPECIFICATION
SIM Card Connector, Hinged Type, 8 Pin, SMT, 1.50mm Profile. Page 1 SIM Card Connector, Hinged Type, 8 Pin, SMT, 1.50mm Profile. Page 2 1.0 SCOPE. This specification covers performance, tests and quality
More informationThese devices require adequately trained and experienced operating personnel.
MMA, 2014 PI Ceramic GmbH PD410 Circular PICMA Bender Piezo Actuators Figure 1: Circular PICMA bender actuator (here: PD410.10) INFORMATION Before soldering, installing and operating the actuator, read
More informationLCI User Manual mantracourt.com
LCI User Manual mantracourt.com LCI Load Cell Junction Box with Fault Monitor Contents Chapter 1 Introduction to the LCI... 2 Chapter 2 Installing the LCI... 3 Chapter 3 Setting up the LCI... 4 Sequence
More informationPRODUCT SPECIFICATION
SIM Card Connector, Hinged Type, 6 Pin, SMT, 1.85mm Profile. Page 1 SIM Card Connector, Hinged Type, 6 Pin, SMT, 1.85mm Profile. Page 2 1.0 SCOPE. This specification covers performance, tests and quality
More informationHIGHLY ACCELERATED LIFE TEST REPORT CM2-400-Q-01
HIGHLY ACCELERATED LIFE TEST REPORT CM2-400-Q-01 Prepared for: Mr. Tom Davenport Ampro Computers, Inc. 5215 Hellyer Avenue, Unit 110 San Jose, California 95138 phone: 408.360.0200 tdavenport@ampro.com
More informationTHERMAL AND VIBRATION ISOLATION TECHNIQUES FOR HARD DRIVES AND PCI CARDS
BIOGRAPHY THERMAL AND VIBRATION ISOLATION TECHNIQUES FOR HARD DRIVES AND PCI CARDS Mike Silverman, C.R.E. Managing Partner, Ops A La Carte, LLC Page 1 of 7 Reliability Engineering Services Mike is an experienced
More informationG.R.A.S. 40AP 1/2" Ext. Polarized Pressure Microphone, High Sensitivity
Date 16-11-2016. Page 1 of 8 G.R.A.S. 40AP 1/2" Ext. Polarized Pressure Microphone, High Sensitivity Freq range: 3.15 Hz to 10 khz Dyn range: 16 dba to 149 db Sensitivity: 50 mv/pa The 40AP is an IEC 61094
More informationMini PCI Express & msata Connector
09.Mar.2012 Rev. C Mini PCI Express & msata Connector 1 Scope: 1.1 Contents This specification covers the requirements for product performance, test methods and quality assurance provisions of MINI PCI
More informationG.R.A.S. 40EN 1" Ext. Polarized Pressure Microphone
Date 16-11-2016. Page 1 of 8 Freq range: 2.6 Hz to 8 khz Dyn range: 9.6 dba to 146 db Sensitivity: 50 mv/pa The 40EN is an IEC 61094 WS1P 1" externally polarized pressure microphone. It is a 1" pressure
More informationPRODUCT SPECIFICATION
1.0 SCOPE DDR4 DIMM SOCKET This Product Specification covers the 0.85mm centerline gold plated DDR4 DIMM edge card connector for 1.40 ± 0.10 thick memory modules..0 PRODUCT DESCRIPTION.1 PRODUCT NAME AND
More informationPOWER ELECTRONICS REPAIR & WARRANTY. Taking the risk out of repair & warranty
POWER ELECTRONICS REPAIR & WARRANTY Taking the risk out of repair & warranty Anecto is a leading provider of Power Electronic Engineering Repair and Warranty Programs for the Renewable Energy sector. Leveraging
More informationCompact Inductive Proximity Sensor
SERIES Compact Inductive Proximity Sensor Amplifier Built-in High functionality together with robust housing and flexible cable Miniature is an amplifier built-in inductive proximity sensor having a diameter
More informationGX SERIES. Cylindrical Compact Inductive Proximity Sensor Amplifier Built-in. Robust enclosure and flexible cable types are also available
8 Cylindrical Compact Inductive Proximity SERIES Related Information General terms and conditions... F-7 Glossary of terms... P.86~ selection guide... P.757~ General precautions... P.05 PHOTO PHOTO Conforming
More informationDC 3-wire Cylindrical Inductive Proximity Sensor. Long sensing range
INDUCTIVE SERIES DC 3-wire Cylindrical Inductive Proximity Oil resistant Metal embedding possible Amplifier Built-in GX G-6 High performance and environmental resistance at low price G-8/8U GA-/GH GX GX-U/FU
More informationAIR COOLED MODULAR RECTIFIER
CONTROLLED POWER COMPANY SPECIFICATIONS AIR COOLED MODULAR RECTIFIER Spc1800a1 5JAN1999 SPECIFICATION S-1800-A MODULAR (REMOVABLE AND NON-REMOVABLE MODULES) AIR COOLED RECTIFIER Standard output power range:
More informationTOUGHER THAN THE REST
TOUGHER THAN THE REST The rugged automotive microphone from GRAS Provides accurate data under even the most challenging test conditions. Resists shock, vibration, drop, water, dust and extreme temperatures.
More informationPHASETRONICS. SCR Power Control Specialists. EP1 Series Power Control Single Phase SCR Amps OPERATION & SERVICE MANUAL
PHASETRONICS Specialists EP1 Series Power Control Single Phase SCR 10-50 Amps OPERATION & SERVICE MANUAL Phasetronics, Inc. P.O. Box 5988 1600 Sunshine Drive Clearwater, FL 33765 (727)573-1900 FAX(727)573-1803
More informationCylindrical Compact Inductive Proximity Sensor Amplifier Built-in. panasonic.net/id/pidsx/global
8 PHOTO PHOTO MEASURE Cylindrical Compact Inductive Proximity SERIES Related Information General terms and conditions... F- Glossary of terms... P.576~ panasonic.net/id/pidsx/global guide... P.78~ General
More informationProven Industrial Reliability for Mission-critical Communications
Proven Industrial Reliability for Mission-critical Communications Professional Ethernet networks often deploy rackmount Ethernet switches in a variety of applications. However, a major issue we face is
More informationSimulation Method for Connector Packaging
Simulation Method for Connector Packaging Makoto Sakairi Tadashi Tateno Akira Tamura (Manuscript received December 28, 2009) There is a growing demand for technology that can analyze and test contact reliability
More informationPC Board Sockets. Specifications SOCKETS. Surface Mount, Single Piece construction. Throughboard, Two Piece construction. Materials.
Sockets Contents SMT PCB Sockets Sockets For Ø0.5mm Pin Sockets For Ø0.8mm Pin Sockets For Ø1mm Pin Sockets For Ø2mm Pin Test Sockets IC Socket Strip Dual Row IC Socket Surface Mount, Single Piece construction
More informationCeramic Surface Mount Mounting Pad Dimensions and Considerations
25111 eramic Surface Mount Mounting Pad imensions and onsiderations The objective of this document is to introduce the IP-SM-782 methodology for solder reflow land patterns. The methodology will be extended
More informationTable of Contents. 1 Introduction. 2 Reliability Assurance Overview and Philosophy. 3 Basic Reliability Assurance Program Requirements
Reliability Requirements for Passive Optical Components GR-1221-CORE Table of Contents Table of Contents 1 Introduction 1.1 Scope and Purpose.................................. 1 2 1.2 Changes in the Document..............................
More informationDC 3-wire Cylindrical Inductive Proximity Sensor. Long sensing range
INDUCTIVE SERIES DC 3-wire Cylindrical Inductive Proximity Oil resistant Metal embedding possible Amplifier Built-in GX G-6 High performance and environmental resistance at low price GA-/GH GX GX-U/FU
More informationENVIRONMENTAL REPORT: EXECUTIVE SUMMARY 6/24/09 Testing performed 6/21/09 thru 6/24/09
a subsidiary of SL INDUSTRIES, INC. ISO 9001:2000 CERTIFIED 6050 King Dr., Bldg. A Ventura, CA 93003 TELEPHONE (805) 486-4565 FAX (858) 712-2040 www.slpower.com ENVIRONMENTAL REPORT: EXECUTIVE SUMMARY
More informationTable of contents Page
User Guide Prog-Box Thank you for purchasing a Hacker Brushless Motors product. The MASTER Prog-Box was developed in close cooperation with JETI and incorporates the latest technological developments.
More informationProduct Service. Choose certainty. Add value. Aerospace Services. First class solutions. TÜV Product Service Ltd TÜV SÜD Group
Product Service Choose certainty. Add value. Aerospace Services First class solutions TÜV Product Service Ltd TÜV SÜD Group Overview TÜV Product Service is a preferred supplier to many of the major aircraft
More informationProcelerant CEQM57XT
[Print This Datasheet] Procelerant CEQM57XT FEATURE SUMMARY -25C to 70C Extended Temperature Range Intel Core i5 and i7 Processor options Intel Core i7 610E 2.53GHz Intel Core i7 620LE 2.0GHz Intel Core
More informationOPERATOR MANUAL OSD361 FIBER OPTIC CCTV TRANSMITTER MODULE
OPERATOR MANUAL OSD361 FIBER OPTIC CCTV TRANSMITTER MODULE OSD361 FIBER OPTIC CCTV TRANSMITTER MODULE Document No. 10102303 PAGE 1 INDEX 1 1 TECHNICAL SUMMARY... 3 1.1 BRIEF DESCRIPTION...3 1.1.1 OVERVIEW...
More informationPRODUCT SPECIFICATION. MES3050 Rev A Date 11/06/09 T-Flash Memory Card, Push-Push + SIM Card (6-Pin), Push-Pull (2-in-1 Combo Connector).
Page 1 Page 2 1.0 SCOPE. This specification covers performance, tests and quality requirements for the 2-in-1 Combo Connector MES3050 (T-Flash Push-Push + SIM 6-Pin Push-Pull). 2.0 PRODUCT NAME AND PART
More informationHelium-Neon Laser Heads 1100 Series
COMMERCIAL LASERS Helium-Neon Laser Heads 1100 Series Key Features Long operating life Low noise Exceptional beam-pointing stability Long-term amplitude stability Applications Flow cytometry Metrology
More informationHelium-Neon Laser Heads Series
1100 Series www.lumentum.com Data Sheet The Lumentum 1100 Series red helium-neon laser products offer low noise, high power stability, and long life for the most demanding applications. With more than
More informationTriax Accelerometer for Route-Based Vibration Analysis
Machinery Health Triax Accelerometer for Route-Based Vibration Analysis A newly-developed triax accelerometer developed specifically for route-based vibration data acquisition for industrial machinery
More informationVCXO Performance Tradeoffs in PLL Designs
September 21, 2011 VCXO Performance Tradeoffs in PLL Designs Table of Contents 1 Introduction...2 2 Basic PLL architecture...2 2.1 PLL as a frequency tracker/filter...2 3 Effects of VCXO parameters on
More informationData Sheet for Linear Sensors
MDCG MDCL MDCT-Plug MDCT-Cable With integrated electronics Probe, ball joints, loose push rod (loose core) Measuring strokes from 2 to 0 mm Cable or plug connection Supply voltage ± 1 V or 24 V Output
More informationModel NPN output PNP output Standard. configuration
Slot-type Photomicrosensor (Non-modulated) *1 EE-SX4/6 CSM_EE-SX4_6_DS_E 1 Global Standard Slot-type photomicrosensors with 0- to 100-mA direct switching capacity. Series includes models that enable switching
More informationTS1000T Ceramic Evaluation Board (CEB1000_1)
TS1000T Ceramic Evaluation Board (CEB1000_1) These ceramic evaluation boards for the high-temperature TS1000T-series accelerometers are optimized evaluation boards designed to allow users to quickly and
More informationCHAPTER 5 RANDOM VIBRATION TESTS ON DIP-PCB ASSEMBLY
117 CHAPTER 5 RANDOM VIBRATION TESTS ON DIP-PCB ASSEMBLY 5.1 INTRODUCTION Random vibration tests are usually specified as acceptance, screening and qualification tests by commercial, industrial, and military
More informationAlun D. Jones.
Environmental Screening Alun D. Jones www.micross.com Why? Environmental screening is intended to determine whether a particular device or batch of devices can survive in a given environment, for a known
More informationOCT 17 Rev A
Product Specification 108-133085 05OCT 17 Rev A The product described in this document has not been fully tested to ensure conformance to the requirements outlined below. Therefore, TE Connectivity (TE)
More informationLCI Load Cell Junction Box with Fault Monitor
LCI Load Cell Junction Box with Fault Monitor User Manual www.mantracourt.co.uk The LCI Load Cell Failure Alarm Manual Chapter 1 Introduction to the LCI...2 Chapter 2 Installing the LCI...3 Figure 2.1
More informationQualification Strategies of Field Programmable Gate Arrays (FPGAs) for Space Application October 26, 2005
Qualification Strategies of Field Programmable Gate Arrays (FPGAs) for Space Application October 26, 2005 Douglas Sheldon Harald Schone Historical FPGAs have been used in spacecraft for over 10 years.
More informationGRAS 40AO 1/2" Prepolarized Pressure Microphone
GRAS 40AO 1/2" Prepolarized Pressure Freq range: 3.15 Hz to 20 khz Dyn range: 20 db(a) to 163 db Sensitivity: 12.5 mv/pa GRAS Sound & Vibration A/S Skovlytoften 33, 2840 Holte, Denmark www.gras.dk The
More informationAI-917-A0. Analogue Input Module (4x 0-20 ma)
General Specifications GS48D17A00-00E-N AI-917-A0 Analogue Input Module (4x 0-20 ma) GENERAL Figure 1 This module has four analogue inputs and four logic pulse outputs. AI-917-A0 Analogue Input Module
More informationS e l e c t i v e S o l d e r i n g S y s t e m S E H O S E L E C TL I N E - C. Total Solutions. SEHO SelectLine-C
Total Solutions for Soldering Processes and Automated Production Lines SEHO SelectLine-C S e l e c t i v e S o l d e r i n g S y s t e m S E H O S E L E C TL I N E - C Patented by SEHO: Ultrasonic Cleaning
More informationCHIP ON BOARD (COB) MODULE 1 WITH 8-BIT MCU KEYBOARD CONTROLLER
PRELIMINARY PRODUCT SPECIFICATION CHIP ON BOARD (COB) MODULE WITH 8-BIT MCU KEYBOARD CONTROLLER FEATURES Device ROM (KB) Low Power Consumption I/O Lines Speed (MHz) Z86K5 4 32 4-5 Z86C5 4 32 4-5 Z0865
More informationINSTRUCTION MANUAL. SIL 3 Switch/Proximity Detector Repeater Relay Output, Termination Board Models D6032S, D6032D
D603S D603D INSTRUCTI MANUAL SIL 3 Switch/Proximity Detector Repeater Relay, Termination Board Models D603S, D603D D603 SIL 3 Switch/Proximity Detector Repeater Relay G.M. International ISM0400 General
More informationPerformance Specifications. Frequency Stabilities Parameter Min Typ Max Units Condition
PX-400 Clock Oscillator PX-400 PX-400 Features Commercial and MIL models Fully RoHS Compliant * No Pure-Tin Temperature range from 0 C to 70 C to -55 C to +125 C Standard 4 and 14 pin DIP hermetic packages
More informationModular and Scalable Power Converters in the UPS Industry
A-PDF Split DEMO : Purchase from www.a-pdf.com to remove the watermark Modular and Scalable Power Converters in the Industry Ian Wallace Eaton Corporation, Innovation Center 1 Eaton Overview Eaton Electric
More informationThese devices require adequately trained and experienced operating personnel.
MMa, 2017 PI Ceramic GmbH PL112 PL140 Rectangular PICMA Bender Piezo Actuators Figure 1: Different rectangular PICMA bender actuator models INFORMATION Before soldering, installing and operating the actuator,
More informationSDQR 108. Preliminary
PD69012 12 Ports AF/AT PoE Device Qualification Report Table of Contents 1. Introduction 3 2. Product Information 3 3. IC Design and Manufacturing Flow Chart 4 4. Qualification Tests Results 5 5. Package
More informationUTS UTS. UTS provides a connection that performs faster, easier, safer and more reliable, it makes :
Company Profile UTS Contents Company profile... 2 Contents... 3 Description... 3 Overview TRIM TRIO... 4 Major features & benefits 5-9 Contact styles... 5 Rapid and secure locking system... 6 Rapid and
More informationElectronics Cooling Using Conduction Convection Radiation from Heat Sinks to Heat Pipes - CFD Consulting Services
Electronics Cooling Using Conduction Convection Radiation from Heat Sinks to Heat Pipes - CFD Consulting Services Predictive Engineering s CFD Consulting Experience Electronics cooling can be as simple
More informationTÜV SÜD Industrie Service GmbH. Maximising efficiency of power stations and plants.
TÜV SÜD Industrie Service GmbH Maximising efficiency of power stations and plants. Maximising efficiency, increasing safety and availability at TÜV SÜD, we know what is important for power stations and
More informationFeatures. Applications
Ultra-Precision 1:8 CML Fanout Buffer with Internal I/O Termination General Description The is a 2.5V/3.3V precision, high-speed, fully differential CML 1:8 fanout buffer. The is optimized to provide eight
More informationTETRIS 2500 High Impedance Active Probe. Instruction Manual
TETRIS 2500 High Impedance Active Probe Instruction Manual Copyright 2018 PMK GmbH All rights reserved. Information in this publication supersedes that in all previously published material. Specifications
More informationLine reactors SINAMICS. SINAMICS G130 Line reactors. Safety information 1. General. Mechanical installation 3. Electrical installation
Safety information 1 General 2 SINAMICS SINAMICS G130 Mechanical installation 3 Electrical installation 4 Technical specifications 5 Operating Instructions Control version V4.7 04/2014 A5E00331462A Legal
More informationBuffer module CP-B 24/20.0, ultra-capacitor based Accessory for power supplies (e.g. switch mode power supplies CP range)
Data sheet Buffer module CP-B 24/20.0, ultra-capacitor based Accessory for power supplies (e.g. switch mode power supplies CP range) The CP-B 24/20.0 serves to ensure a shortterm uninterrupted power supply
More informationDisplacement Sensors High Performance Displacement Transducers S Series
Displacement Sensors High Performance Displacement Transducers S Series Description The S Series Displacement Sensor is the accumulation of many years experience gained from Solartron s pedigree of producing
More informationWasp Embedded Controller
Wasp Embedded Controller Wasp16/32/64 Hardware Reference Guide PCB Rev 1.0 WASP16 WASP32 WASP64 MC433 Hardware Reference Guide Manual Revision 0.85 Table of Contents Warranty Statement...2 1.0 Introduction....4
More informationUSER S MANUAL ENTITY. Energy Meter TRINITY. Entity Operational Manual
USER S MANUAL ENTITY Energy Meter This document contains the latest technical information about ENTITY which is a micro-controller based Energy Meter. The unit is tested against latest "MTE" Standard Model
More informationVariTrans P Standard-Signal Isolators
VariTrans Standard-Signal Isolators Warranty Defects occurring within 5 years from delivery date shall be remedied free of charge at our works (carriage and insurance paid by sender). The professional
More informationPRODUCT SPECIFICATION
Dual SIM Card Connector, Retainer Type, 8-Pin, SMT, 3.0mm Profile Page 1 Dual SIM Card Connector, Retainer Type, 8-Pin, SMT, 3.0mm Profile Page 2 1.0 SCOPE. This specification covers performance, tests
More informationHelium-Neon Laser Heads 1100 Series
COMMERCIAL LASERS Helium-Neon Laser Heads 1100 Series Key Features Long operating life Low noise Exceptional beam-pointing stability Long-term amplitude stability Applications Flow cytometry Metrology
More informationHB5M. Hollow Bore Optical Encoder Page 1 of 5. Description. Mechanical Drawing. Features
Description HB5M Page 1 of 5 The HB5M is a hollow bore (hollow shaft / thru-bore) optical encoder with a machined aluminum enclosure and an anodized protective finish. The HB5M optical incremental encoder
More informationSM320A~SM3200A SCHOTTKY DIODE REVERSE VOLTAGE 20 TO 200V FORWARD CURRENT 3.0A
320A~3200A DESCRIPTION The 320A~3200A are available in A Package. ORDERING INFORMATION Package Type Part Number 320A 340A 360A 380A A 3100A 3120A 3150A 3200A Note 5,000pcs/Reel AiT provides all RoHS Compliant
More informationXU1-DC DC voltage relay. (June 1998) Manual XU1-DC (Revision New)
XU1-DC DC voltage relay (June 1998) Manual XU1-DC (Revision New) Woodward Manual XU1-DC GB Woodward Governor Company reserves the right to update any portion of this publication at any time. Information
More informationSolve Data Acquisition Compatibility Problems by Combining Features and Performance
Solve Data Acquisition Compatibility Problems by Combining Features and Performance By Brendan Whelan, Design Manager, Signal Conditioning Products Linear Technology Corp. Modern data acquisition and signal
More informationIn North America call toll free: Fax
WTS Inclinometer All-weather radio telemetry Inclinometer system Features Advanced MEMS inclinometer design for ultra-reliability and performance Distortion free digital 2 way radio system for data integrity
More informationMini PCI Express Card Socket
Mini PCI Express Card Socket Document No: Page: 1 of 4 1. Scope This specification covers the material and performance requirements for the Mini PCI Express Card Socket series. 2. Applicable documents
More informationInternational PV Quality Assurance Task Force
International PV Quality Assurance Task Force Solar ABCs Meeting, Dallas, TX Sarah Kurtz, John Wohlgemuth NREL Tony Sample EC-JRC Masaaki Yamamichi AIST James Amano SEMI Oct. 21, 2011 NREL is a national
More informationBurson Audio DA-160 Audio DAC User Manual
Burson Audio DA-160 Audio DAC User Manual www.bursonaudio.com Want free warranty extension? Please read page 7 for details. Burson Audio U1 U2 C T H L THANK YOU...3 TEAM BURSON...3 UNPACKING...4 THE ACCESSORY
More informationDP500IP 1AC/ DP500IP 3AC Manual
DP500IP 1AC/ DP500IP 3AC Manual IP67 Power Supply Content 1) General safety instructions... 4 2) Technical Data... 6 3) Installations... 6 4) Function and Signals... 7 5) Service Center / Rapair... 8 6)
More informationDatamate High-Reliability Connectors
Datamate High-Reliability Connectors Industry recognised, British Standard approved Datamate is the field-proven high-reliability range of choice for many industries. Approved to British Standard 9525-F0033
More informationD6030S - D6030D INSTRUCTION MANUAL. D SIL 3 Switch/Proximity Detector Repeater Relay Output. Models D6030S, D6030D
D600S - D600D INSTRUCTI MANUAL SIL Switch/Proximity Detector Repeater Relay, DIN Rail, Models D600S, D600D D600 - SIL Switch/Proximity Detector Repeater Relay G.M. International ISM0- Characteristics General
More informationUniStream Uni-I/O Modules
UniStream Uni-I/O Modules Technical Specifications UIS-08TC This guide provides specifications for Unitronics Uni-I/O module UIS-08TC. This module comprises: 8 inputs Uni-I/O modules are compatible with
More informationTILT & TIP-TILT STAGES - PRODUCT AND WARRANTY INFORMATION
TILT & TIP-TILT STAGES - PRODUCT AND WARRANTY INFORMATION Version : 3.3 Date 02/07/15 CEDRAT TECHNOLOGIES URL: http://www.cedrat-technologies.com 59, Chemin du Vieux Chêne-Inovallée Email: actuator@cedrat-tec.com
More informationWTS Inclinometer. All-weather radio telemetry Inclinometer system. Features. WTS Wireless Inclinometer. Dimensions
WTS Inclinometer All-weather radio telemetry Inclinometer system Features Advanced MEMS inclinometer design for ultra-reliability and performance Distortion free digital 2 way radio system for data integrity
More informationHSP line ESD protection for high speed lines. Applications. Description. Features. µqfn 4 leads. Benefits. Complies with following standards
2-line ESD protection for high speed lines Datasheet - production data Benefits High ESD robustness of the equipment Suitable for high density boards Complies with following standards MIL-STD 883G Method
More informationSolder Column Qualification for Ceramic Column Grid Array (CCGA) White Paper. Aeroflex Colorado Springs October 2006, Revised July 2008
Solder Column Qualification for Ceramic Column Grid Array (CCGA) White Paper Aeroflex Colorado Springs October 2006, Revised July 2008 Introduction The aerospace industry continues to require increasing
More informationPM2 SERIES. Convergent Reflective Micro Photoelectric Sensor. Convergent reflection sensing ensures stable detection. Hardly affected by background
PHOTO PHOTO USE MEASUREMENT STATIC CONTROL Micro Photoelectric SERIES Related Information General terms and conditions... F- Glossary of terms... P.39~ selection guide... P.~ General precautions... P.0
More informationGX-5SU(B) is just 5.4 mm 0.213in in diameter, the smallest in existing DC two-wire sensors. It saves you space.
DC 2-wire Cylindrical Inductive Proximity SERIES Amplifier Built-in High performance & ease of use Robust in tightening The tightening torque has been improved to approx. four times greater than that of
More informationSliceMaster (Multi-site recording system)
Experts in Electrophysiology & Imaging High Throughput SliceMaster (Multi-site recording system) Higher throughput, optimal sample use www.scientifica.uk.com/slicemaster www.scientifica.uk.com 2 SliceMaster
More informationRequirements for editing 8D Reports
Requirements for editing 8D Reports (jochen.keidel) (daniel.bihlmaier) Seite 1 von 8 Version Date Comment 1 15.11.2017 Translation into English Index 1 Guideline... 3 2 Content and form for processing
More informationScienceDirect. Vibration Response Prediction of the Printed Circuit Boards using Experimentally Validated Finite Element Model
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 144 (2016 ) 576 583 12th International Conference on Vibration Problems, ICOVP 2015 Vibration Response Prediction of the Printed
More informationPLD Series +5V Laser Diode Drivers
PLD Series +5V Laser Diode Drivers General Description The PLD series of Laser Diode Drivers combines the high performance you expect from a Wavelength component with two distinct improvements: low voltage
More informationIn the HALT testing the product performed quite well, but there are some areas that need investigation and corrective action:
March 6, 2006 Ms. Sandra Mandawe LGC Wireless, Inc. 2540 Junction Avenue San Jose, CA 95134 Dear Ms. Mandawe, Attached is the Highly Accelerated Life Test Report for the Technologic Systems TS-7250. Testing
More informationSeries PC 3.5 precision subminiature connectors
Series PC 3.5 precision subminiature connectors Description Content HUBER+SUHNER PC 3.5 connectors are precision connectors for use in microwave applications up to 26.5 GHz. They are especially suitable
More informationEfficient and Power Saving Driving Methods for High Power LEDs in General Lighting Applications
Efficient and Power Saving Driving Methods for High Power LEDs in General Lighting Applications Conference Electronic Displays 2011 March 2-3 Nürnberg Georg Machon RoodMicrotec Stuttgart Based on essential
More informationMar11 Rev C
Product Specification 108-1956 11Mar11 Rev C PC/104 and PC/104-Plus Connector Systems 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the TE Connectivity
More informationEDG Port Industrial 10/100 Mbps Ethernet Switch. User Manual
EDG-6528 8-Port Industrial 10/100 Mbps Ethernet Switch User Manual Copyright The documentation and the software included with this product are copyrighted 2005 by Advantech Co., Ltd. All rights are reserved.
More informationOVP2. The Over-Voltage Protector 2 (OVP2) Technical Literature
The Over-Voltage Protector 2 (OVP2) Technical Literature INTRODUCTION The Over-Voltage Protector (OVP) design has been established since 1999 as the premier explosion-proof (Division 1) protection device
More informationReal-Time Automation Controllers (RTACs) Economical, multifunctional, compact real-time automation control
SEL-3505/3505-3 Real-Time Automation Controllers (RTACs) Economical, multifunctional, compact real-time automation control RTAC versatility facilitates easy event collection, protocol conversion, and secure
More informationHelium-Neon Laser Heads 1100 Series
COMMERCIAL LASERS Helium-Neon Laser Heads 1100 Series Key Features Long operating life Low noise Exceptional beam-pointing stability Long-term amplitude stability Applications Flow cytometry Metrology
More information