ARIB STD-T64-C.S v1.0. Mobile Equipment(ME) Conformance Testing with CSIM for cdma2000 Spread Spectrum Standards

Transcription

1 ARIB STD-T-C.S00-0 v.0 Mobile Equipment(ME) Conformance Testing with CSIM for cdma000 Spread Spectrum Standards Refer to "Industrial Property Rights (IPR)" in the preface of ARIB STD-T for Related Industrial Property Rights. Refer to "Notice" in the preface of ARIB STD-T for Copyrights

2 Original Specification This standard, ARIB STD-T-C.S00-0 v.0, was prepared by GPP-WG of Association of Radio Industries and Businesses (ARIB) based upon the GPP specification, C.S000-0 v.0. Modification to the original specification None. Notes None. 0

3 GPP C.S00-0 Version.0 January 0 Mobile Equipment (ME) Conformance Testing with CSIM for cdma000 Spread Spectrum Standards 0 GPP GPP and its Organizational Partners claim copyright in this document and individual Organizational Partners may copyright and issue documents or standards publications in individual Organizational Partner's name based on this document. Requests for reproduction of this document should be directed to the GPP Secretariat at secretariat@gpp.org. Requests to reproduce individual Organizational Partner's documents should be directed to that Organizational Partner. See for more information.

4 Revision History Revision Description of Changes Date C.S00-0 v.0 Initial release January 0

5 Table of Contents i

6 ii

7 0 0 0 iii

8 This page intentionally left blank. iv

9 FOREWORD This foreword is not part of this specification. This specification was prepared by the Third Generation Partnership Project (GPP). v

10 This page intentionally left blank. vi

11 0 0 INTRODUCTION. Scope This is the ME Conformance Testing with CSIM specification. The aim of the present document is to ensure interoperability between an ME and a CSIM independently of the respective manufacturer, card issuer or operator as defined in [], [] and []. The present document does not define any aspects related to the administrative management phase of the UICC. Any internal technical realization of either the UICC or the ME is only specified where these are reflected over the interface. This document does not specify which test cases are mandatory or optional. However, to successfully execute a particular test case, its corresponding test requirements and procedures as defined in this document shall be followed.. Document Conventions.. Requirements Shall and shall not identify requirements to be followed strictly to conform to this document and from which no deviation is permitted. Should and should not indicate that one of several possibilities is recommended as particularly suitable, without mentioning or excluding others, that a certain course of action is preferred but not necessarily required, or that (in the negative form) a certain possibility or course of action is discouraged but not prohibited. May and need not indicate a course of action permissible within the limits of the document. Can and cannot are used for statements of possibility and capability, whether material, physical or causal... Numbers The following table describes the conventions used for non-decimal numbers. Convention Description b A single digit binary number bbbbbbbb An -bit binary number hh A single octet hexadecimal number hh hh hh hh hh A multi-octet hexadecimal number Note: If an X is present in a binary or hexadecimal number, then that digit is don t care. 0 Bn represents Byte n of the coding starting from left to right, i.e. MSB to LSB. bn represents Bit n of the byte starting from right to left, i.e. LSB to MSB.. Terminology.. Definitions For the purposes of the present document, the following terms and definitions apply in addition to the terms defined in []: Mobile Equipment: The part of a mobile station that does not include the UIM. Mobile Station: A station, fixed or mobile, which serves as the end user s wireless communication link with the base station. Mobile stations include portable units (e.g., hand-

12 0 0 0 held personal units) and units installed in vehicles. A mobile station consists of two parts ME and UIM... Acronyms For the purposes of the present document, the following acronyms apply: GPP rd Generation Partnership Project ADF Application Directory File CSIM cdma000 Subscriber Identity Module CS Card Simulator DF Directory File EF Elementary File ME Mobile Equipment MEID Mobile Equipment Identifier MS Mobile Station NS Network Simulator OTAPA Over-the-Air Parameter Administration OTASP Over-the-Air Service Provisioning PIN Personal Identity Number PIN Personal Identity Number PRL Preferred Roaming List SIM Subscriber Identity Module UICC Universal Integrated Circuit Card UIM User Identity Module. References The following standards are referenced in this text. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based upon this document are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. ANSI and TIA maintain registers of currently valid national standards published by them. Normative: [] GPP C.S00-B v.0, cdma000 Application on UICC for Spread Spectrum Systems, January 0. cdma000 is the trademark for the technical nomenclature for certain specifications and standards of the Organizational Partners (OPs) of GPP. Geographically (and as of the date of publication), cdma000 is a registered trademark of the Telecommunications Industry Association (TIA-USA) in the United States.

13 0 [] GPP C.S00-A v.0, UICC-Terminal interface Physical and Logical characteristics for cdma000 Spread Spectrum Systems, January 00. [] ETSI TS 0, V..0, Smart Cards; UICC-Terminal interface; Physical and logical characteristics, October 00. [] GPP C.S00-A v.0, Mobile Equipment (ME) Conformance Testing with R-UIM for cdma000 Spread Spectrum Systems, October 00. [] GPP C.S00-0 v.0, Signaling Conformance Tests for cdma000 Spread Spectrum Systems, September 00. [] GPP TS. V..0, UICC-terminal interface; Universal Subscriber Identity Module (USIM) application test specification (Release ), October 00.

14 This page intentionally left blank.

15 RESERVED RESERVED

16 This page intentionally left blank.

17 ME TEST ENVIRONMENT The following diagram illustrates the test environment involving the ME (the Unit Under Test), a Card Simulator (CS), and a Network Simulator (NS). 0 0 Figure ME Test Environment The NS simulates a cdma000 network and can receive or originate cell phone calls. The CS simulates a UICC containing a CSIM. Alternatively, to perform the logical tests, CSIMs programmed with specific data may be used. The CSIM data is not defined within the initial conditions of the tests unless it differs from the default values defined below. The following sequence of tests confirms: The correct interpretation of data read from the CSIM (cdma000 Subscriber Identification Module) by the ME; The correct writing of data to the CSIM by the ME; The initiation of appropriate procedures by the ME; and The high level protocols. All tests apply to the CSIM application on the UICC.. Definition of Default Values for ME CSIM Interface Testing (Default UICC) A CSIM containing the following default values is used for all tests of this present document unless otherwise stated. For each data item, the logical default values and the coding within the elementary files (EFs) of the CSIM follow. Unless otherwise specified, the coding values are hexadecimal... Values of the EFs under MF The following EFs exist under the UICC Master File (MF) level.... EF DIR (Directory) This EF must contain an AID for the CSIM, i.e. 'A XXXXXXXXXXXXXXXX'.

18 ... EF PL (Preferred Languages) Logically: en (English) Coding: B B E.. Values of the EFs under DFTELECOM/DFMMSS... EF MLPL (MMSS Location Associated Priority List) Logically: Size bytes Coding: B B EF MSPL (MMSS System Priority List) Logically: Size bytes Coding: B B Values of the EFs under ADF-CSIM The following EFs exist under the CSIM Application DF (ADF) level.... EF IMSI_M (IMSI_M) See section.. of [].... EF IMSI_T (IMSI_T) Logically: IMSI_T_CLASSp: Class 0 IMSI_T_S: 000 IMSI_T_S: 0000 IMSI_T p: 0 IMSI_T_PROGRAMMED/ IMSI_T_ADDR_NUMp: IMSI_T has not been programmed, Address 000 MCC_Mp: 0 (India) Coding: B B B B B B B B B B0 0 E 0 A E F EF AD (Administrative Data) Logically: Normal operation No additional information Coding: B B B EF CSIM_ST (CSIM Service Table) Logically: The following table lists the logical values.

19 Service Description Available n Local Phone book Yes n Fixed Dialing Numbers (FDN) Yes n Extension Yes n Service Dialing Numbers (SDN) No n Extension No n Short Message Storage Yes n Short Message Parameters Yes n HRPD Yes n Category Program for BC-SMS No n0 CDMA Home Provider Name Yes n Data Download via SMS Broadcast (for CCAT) No n Data Download via SMS-PP (for CCAT) No n Call Control (for CCAT) No n GPD-SIP Yes n GPD-MIP Yes n AKA Yes n IP-based Location Services (LCS) No n BCMCS No n Multimedia Messaging (MMS) Yes n0 Extension Yes n MMS User Connectivity Parameters Yes n Application Authentication No n Group Identifier Level No n Group Identifier Level No n De-Personalization Control Keys No n Cooperative Network List No n Outgoing Call Information (OCI) No n Incoming Call Information (ICI) No n Extension No n0 Multimedia Storage No n Image (EF IMG) No n Enabled Services Table Yes n Capability Configuration Parameters (CCP) No n SF_EUIMID-based EUIMID Yes

20 Service Description Available n Messaging and GPD Extensions Yes n Root Certificates Yes n WAP Browser Yes n Java Yes n Reserved for CDG No n0 Reserved for CDG No n IPv No Coding: B B B B B B E C 0 E EF EST (Enable Service Table) Logically: Fixed Dialing Numbers (FDN) disabled. Coding: B EF OTA (OTASP/OTAPA Features) Logically: Number of features: DATA_P_REV: 0 A_KEY_P_REV: 0 SSPR_P_REV: 0 SPL_P_REV: 0 OTASP_P_REV: 0 MMSS_P_REV: 0 Coding: B B B B B B B B B B0 B B B B 0... EF RUIMID (UIM_ID) Logically: Pseudo-UIMID Coding: B B B B B B B B 0 E 0 0 FF FF FF 0

21 ... EF MECRP (ME-specific Configuration Request Parameters) Logically: SCM 0 MOB_P_REV 0 Local Control for Analog 0 Local Control for CDMA 0 Coding: B B B EF ACCOLC (Access Overload Class ACCOLCp) Logically: 0 Derived from last digit of IMSI_M Coding: B EF PRL (Preferred Roaming List) Logically: Size bytes PRL ID 0 Preferred only Default roaming indication 0 Number of Acquisition Records Number of system records Coding: B B B B B B B B B B0 B B B B B B B B E DB 0... EF EPRL (Extended Preferred Roaming List) Logically: Size bytes PRL ID Current Protocol Revision Preferred only Default roaming indication Number of acquisition records Number of records in the Common Subnet Table 0 Number of system records - Coding: B B B B B B B B B B0 B B 00 0 A C B B B B B B B B0 B B B B 0 0B 0 0B

22 B B B B B B0 B B B B B B F0 0 B B B B0 B B B B B B B B B B0 B B EF ADN (Abbreviated Dialing Number) See section..0 of [].... EF PBR (Phone Book Reference file) and Related EFs See section. of [] for EF PBR and related EFs.... EF CDMAHOME (CDMA Home SID, NID) See section.. of [].... EF USGIND (UIM_ID/SF_EUIMID Usage Indicator) See section.. of [].... EF ESN_MEID_ME (ESN_ME) See section.. of [].... EF SPN (CDMA Home Service Provider Name) See section.. of [].... EF SMSCAP (SMS Capabilities) See section.. of [].... EF SMSP (SMS Parameters) See section.. of []....0 EF SIPUPP (SimpleIP User Profile Parameters) See section.. of [].... EF SIPUPPExt (SimpleIP User Profile Parameters Extension) See section.. of [].... EF SIPPAPSS (Simple IP PAP SS) See section.. of [].... Simple IP CHAP SS See section.. of [].

23 EF DGC (Data Generic Configurations) See section.. of [].... EF MIPUPP (Mobile IP User Profiles) See section.. of [].... EF MIPUPPExt (Mobile IP User Profiles Extension) See section..0 of [].... Mobile IP SS See section.. of [].... EF MIPFlags (Mobile IP Flags) See section.. of [].... EF GPDOPM (GPD Operation Mode) See section.. of []....0 EF AppLabels (Application Labels) See section.. of [].... EF Model (Device Model Information) See section.. of [].... EF ECC (Emergency Call Codes) See section.. of [].... EF HRPDCAP (HRPD Capabilities) See section.. of [].... EF HRPDUPP (HRPD Access Authentication User Profile Parameters) See section.. of [].... HRPD Access Authentication CHAP SS See section..0 of [].... EF WAPBrowserCP (WAP Browser Connectivity Parameters) See section.. of [].... EF WAPBrowserBM (WAP Browser Bookmarks) See section.. of [].... EF MMSN (MMS Notification) See section.. of [].

24 0... EF MMSICP (MMS Issuer Connectivity Parameters) See section.. of []....0 EF MMSUP (MMS User Preferences) See section.. of [].... EF MMSConfig (MMS Configuration) See section.. of [].... EF RC (Root Certificates) See section.. of [].... EF JDL (Java Download URL) See section.. of []... Default PINs... PIN Key reference: 0 Logically: Coding: B B B B B B B B FF FF FF FF... PIN Key reference: Logically: Coding: B B B B B B B B FF FF FF FF 0... Unblock PIN Key reference: 0 Logically: Coding: B B B B B B B B... Unblock PIN Key reference: Logically: 0 Coding: B B B B B B B B 0

25 ... Universal PIN Key reference: Logically: Coding: B B B B B B B B FF FF FF FF... Unblock Universal PIN Key reference: Logically: 0000 Coding: B B B B B B B B Definition of FDN CSIM The FDN test cases require a different configuration from the one described in the section.. For that purpose, a default FDN CSIM is defined. In general, the values of the FDN CSIM are identical to the default CSIM, with the following exceptions... Values of the EF s (FDN UICC)... EF EST (Enable Service Table) Logically: Fixed Dialing Numbers activated. Coding: B EF FDN (Fixed Dialing Numbers) See section... of [].. Common Initial Conditions The following initial conditions are applicable to all tests unless otherwise stated in a test: The ME is connected to the NS. The ME is connected to the CS (or has an appropriately programmed CSIM). The CS contains the default file structure defined in section.. Both the NS and CS are powered on. Individual tests may contain additional conditions.

26 This page intentionally left blank.

27 0 0 0 ME TEST PROCEDURES The test cases in this chapter are unique to an ME conforming with a CSIM. Chapter 0 contains the test cases that are in common with an ME conforming with an R-UIM []. In general, for each test procedure, the following five () subsections are included: ) Definition ) Traceability ) Initial Conditions ) Procedure ) Minimum Standard Unless otherwise specified, each test case is applicable to all MEs.. ME Interworking, Initialization and Session Termination.. Definition An ME selects the CSIM application and properly initializes itself and the CSIM. The ME also properly terminates the CSIM session and closes the CSIM application... Traceability For Interworking, see sections and... of []. For Initialization, see section... of []. For Session Termination, see section.. of []... Initial Conditions None beyond the common initial conditions... Procedure. Power on the ME.. Wait for the ME initialization to complete.. Verify that the ME performed the following: Did not select DF CDMA (the R-UIM); Selected ADF-CSIM; Read EF ECC; Read EF PL; Verified the user; Read EF AD; Read EF CSIM_ST; Read EF EST; Read EF OTA if ME supports OTASP/OTAPA; Read EF RUIMID;

28 0 0 0 Sent the Store_ESN_MEID_ME command (EF ESN_MEID_ME has the ME s ESN_ME or MEID); Wrote to EF MECRP; Read EF GCIK if ME supports AKA.. If supported by the ME, verify that the ME performed the following: Read EF SP; Read EF IMSI_M and EF IMSI_T; Read EF ACCOLC; Read EF PRL if ME supports only SSPR_P_REV = ; Read EF EPRL if ME supports SSPR_P_REV ; Wrote to EF Model if EF Model is present; Read EF MLPL if ME supports MMSS_P_REV ; Read EF MSPL if ME supports MMSS_P_REV.. Verify that the ME sent a STATUS command with P = 0.. Power off the ME.. When the ME sends a STATUS command with P = 0 (Session Termination Indications), verify that the ME performed the following: Wrote to EF GCIK if ME supports AKA... Minimum Standard The ME shall comply with the requirements in steps,, and of the procedure.. MSID, MCC, and IMSI Use the test procedure specified in section.. of [] with the following exceptions: Substitute R-UIM with CSIM Substitute Removable UIM_ID_Usage Indicator with UIM ID usage indicator.. PIN Handling Use all of the test procedures specified in section. of [], substituting Terminal with ME and UICC simulator with CS.. Fixed Dialing Number (FDN) Use all of the test procedures specified in sections.... of [] with the following substitutions: ) USIM and SIM/USIM with CSIM ) USS and SS with NS ) Terminal with ME In addition, the appropriate NS settings shall be used in place of the GSM-specific settings identified in [] and the rehabilitation of EF LOCI is not applicable.

29 0. Global Service Redirection between Band Classes Use the test procedure specified in section.. of []... Minimum Standard Verify in steps d and h of the test procedure that the ME read EF ACCOLC.. Phone Book Procedures Use the test procedure specified in section. of [], substituting USIM with CSIM.. UICC Presence Detection Use the test procedure specified in section. of [], substituting generic call setup with voice call setup in section...

30 This page intentionally left blank. 0

31 0 0 0 TESTS IN COMMON WITH R-UIM The test cases in this chapter are in common with the R-UIM []. For all the tests described in this chapter, use the Common Initial Conditions specified in section. of this document and not the Common Initial Conditions specified in section. of []. In all test cases, substitute R-UIM with CSIM in all references to []. Some test cases may require additional substitutions.. MS Identification.. Mobile Station Identifier Use the test procedure specified in section.. of []... MS Displaying the Roaming Indicator Use the test procedure specified in section.. of [].. UIM_ID/ESN_ME Selection.. Removable UIM_ID Usage Indicator Use the test procedure specified in section.. of []... ESN Management Use the test procedure specified in section.. of []... MEID Management Use the test procedure specified in section.. of [] but only for Initial Conditions A... EUIMID and MEID Use the test procedure specified in section.. of [].. Security-related commands.. SSD Update Use the test procedure defined in section.. of []... Authentication Calculation for Global Challenge Use the test procedure defined in section.. of [] with the additional substitution of Run CAVE with Authenticate Run CAVE... Unique Challenge While the Mobile Station is in Idle State Use the test procedure defined in section.. of [] with the additional substitution of Run CAVE with Authenticate Run CAVE... Unique Challenge While the Mobile Station is in Mobile Station Control on the Traffic Channel State Use the test procedure defined in section.. of [] with the additional substitution of Run CAVE with Authenticate Run CAVE.

32 0 0.. Generate Key/VPM Use the test procedure defined in section.. of [] with the additional substitution of Run CAVE with Authenticate Run CAVE.. Reserved. OTASP/OTAPA Functionality.. PRL Download Use the test procedure specified in section.. of []... OTASP/OTAPA Commands Use the test procedure specified in section.. of []... EPRL Download Use the test procedure specified in section.. of [].. Reserved. Reserved. Reserved. Reserved.0 Reserved. Reserved. Reserved. Reserved. Reserved. Abbreviated Dialing Numbers (ADN) Use the test procedure specified in section. of [].. Reserved. Reserved. Reserved. Reserved.0 Reserved

33 0 0. Reserved. Suggested Slot Cycle Index Use the test procedure specified in section. of [].. Service Provider Name Use the test procedure specified in section. of [].. Reserved. Application Labels.. Application Labels Present on CSIM Use the test procedure specified in section.. of []... Application Labels Not Present on CSIM Use the test procedure specified in section.. of [].. Device Model Information Use the test procedure specified in section. of [].. Emergency Numbers Use the test procedure specified in section. of [].. SMS Capabilities.. SMS Retries Use the test procedure specified in section.. of []... Sending SMS on Access Channel Use the test procedure specified in section.. of []... Sending SMS on Traffic Channel Use the test procedure specified in section.. of []... Sending EMS messages Use the test procedure specified in section.. of [].. SMS Messages on CSIM.. Automatically Storing Received SMS in CSIM Use the test procedure specified in section.. of []... Saving SMS in CSIM Use the test procedure specified in section.. of [].

34 0 0.. Reading SMS from CSIM Use the test procedure specified in section.. of []... Deleting SMS in CSIM Use the test procedure specified in section.. of []..0 SMS Parameters on CSIM.0. Saving SMS Parameters in CSIM Use the test procedure specified in section.0. of []..0. Reading SMS Parameters in CSIM Use the test procedure specified in section.0. of []..0. Deleting SMS Parameters in CSIM Use the test procedure specified in section.0. of [].. SMS Status on CSIM Use the test procedure specified in section. of [].. Simple IP.. PAP and CHAP Authentication Use the test procedure specified in section.. of []... Multiple User Profiles Use the test procedure specified in section.. of []... Prioritization among User Profiles Use the test procedure specified in section.. of [].. Mobile IP.. Mobile IP Registration Retries Use the test procedure specified in section.. of []... Mobile IP Re-registration Threshold Use the test procedure specified in section.. of []... Mobile IP to SimpleIP Fallback Use the test procedure specified in section.. of []... Mobile IP MN-HA 00bis Authentication Use the test procedure specified in section.. of [].

35 0 0.. Mobile IP Pre Rev Handoff Optimization Use the test procedure specified in section.. of []... Mobile IP PPP Re-sync during Hand-down from xev-do Rev 0 to x Use the test procedure specified in section.. of []... Mobile IP Re-registration for Extending Mobile IP address lifetime Use the test procedure specified in section.. of [].. Data Configurations.. Data Dormant Mode Timer Use the test procedure specified in section.. of []... Hysteresis Activation Time Use the test procedure specified in section.. of []... EPZID Use the test procedure specified in section.. of [].. HRPD Access Authentication Use the test procedure specified in section. of [].. WAP Browser Connectivity Parameters Use the test procedure specified in section. of [].. WAP Browser Bookmarks Use the test procedure specified in section. of [].. MMS Issuer Connectivity Parameters Use the test procedure specified in section. of [].. MMS Configurations.. Maximum Message Size Use the test procedure specified in section.. of []... MMS Retries Use the test procedure specified in section.. of []... MMSC Timeout Use the test procedure specified in section.. of [].

36 0.0 MMS Notifications.0. Reading and Using MMS Notification in CSIM Use the test procedure specified in section.0. of []..0. Automatically Storing MMS Notification in CSIM Use the test procedure specified in section.0. of []..0. Forwarding MMS Notifications Use the test procedure specified in section.0. of []..0. Deleting MMS Notification from CSIM Use the test procedure specified in section.0. of [].. MMS User Preferences.. Reading and Using MMS User Preferences Use the test procedure specified in section.. of []... Updating MMS User Preferences Use the test procedure specified in section.. of [].. Root Certificates Use the test procedure specified in section. of [].. Java Use the test procedure specified in section. of [].

37 Appendix A APPLICABILITY MATRIX (INFORMATIVE) The following table summarizes the applicability of test cases in terms of testing the ME with a CSIM having a particular C.S00 revision. Test Case C.S00-0 -A -B. ME Initialization No No Yes. MSID, MCC, and IMSI Yes Yes Yes. PIN Handling Yes Yes Yes. Fixed Dialing Number (FDN) Yes Yes Yes. Global Service Redirection between Band Classes Yes Yes Yes. Phone Book Procedures Yes Yes Yes. UICC Presence Detection No No Yes.. Mobile Station Identifier Yes Yes Yes.. MS Displaying the Roaming Indicator Yes Yes Yes.. Removable UIM_ID Usage Indicator Yes Yes Yes.. ESN Management Yes Yes Yes.. MEID Management Yes Yes Yes.. EUIMID and MEID Yes Yes Yes.. SSD Update Yes Yes Yes.. Authentication Calculation for Global Challenge Yes Yes Yes.. Unique Challenge While the Mobile Station is in Idle State Yes Yes Yes.. Unique Challenge While the Mobile Station is in Mobile Station Control on the Traffic Channel State Yes Yes Yes.. Generate Key/VPM Yes Yes Yes.. PRL Download Yes Yes Yes.. OTASP/OTAPA Commands Yes Yes Yes.. EPRL Download Yes Yes Yes. Abbreviated Dialing Numbers (ADN) Yes Yes Yes. Suggested Slot Cycle Index Yes Yes Yes. Service Provider Name Yes Yes Yes.. Application Labels Present on CSIM No Yes Yes.. Application Labels Not Present on CSIM No Yes Yes. Device Model Information No Yes Yes. Emergency Numbers Yes Yes Yes

38 C.S00 Test Case -0 -A -B.. SMS Retries No Yes Yes.. Sending SMS on Access Channel No Yes Yes.. Sending SMS on Traffic Channel No Yes Yes.. Sending EMS messages No Yes Yes.. Automatically Storing Received SMS in CSIM Yes Yes Yes.. Saving SMS in CSIM Yes Yes Yes.. Reading SMS from CSIM Yes Yes Yes.. Deleting SMS in CSIM Yes Yes Yes.0. Saving SMS Parameters in CSIM Yes Yes Yes.0. Reading SMS Parameters in CSIM Yes Yes Yes.0. Deleting SMS Parameters in CSIM Yes Yes Yes. SMS Status on CSIM Yes Yes Yes.. PAP and CHAP Authentication Yes Yes Yes.. Multiple User Profiles No Yes Yes.. Prioritization among User Profiles No Yes Yes.. Mobile IP Registration Retries Yes Yes Yes.. Mobile IP Re-registration Threshold Yes Yes Yes.. Mobile IP to SimpleIP Fallback Yes Yes Yes.. Mobile IP MN-HA 00bis Authentication No Yes Yes.. Mobile IP Pre Rev Handoff Optimization No Yes Yes.. Mobile IP PPP Re-sync during Hand-down from xev-do Rev 0 to x No Yes Yes.. Mobile IP Re-registration for Extending Mobile IP address lifetime No Yes Yes.. Data Dormant Mode Timer No Yes Yes.. Hysteresis Activation Time No Yes Yes.. EPZID No Yes Yes. HRPD Access Authentication Yes Yes Yes. WAP Browser Connectivity Parameters No Yes Yes. WAP Browser Bookmarks No Yes Yes. MMS Issuer Connectivity Parameters Yes Yes Yes.. Maximum Message Size No Yes Yes.. MMS Retries No Yes Yes.. MMSC Timeout No Yes Yes.0. Reading and Using MMS Notification in CSIM Yes Yes Yes

39 C.S00 Test Case -0 -A -B.0. Automatically Storing MMS Notification in CSIM Yes Yes Yes.0. Forwarding MMS Notifications Yes Yes Yes.0. Deleting MMS Notification from CSIM Yes Yes Yes.. Reading and Using MMS User Preferences Yes Yes Yes.. Updating MMS User Preferences Yes Yes Yes. Root Certificates No Yes Yes. Java No Yes Yes

40 This page intentionally left blank. 0