Test Plan for CDMA Mobile Stations

Transcription

1 Test Plan for CDMA Mobile Stations April 2009 Revision 5.4.1

2 CTIA Certification Program Interested parties may obtain permission to reproduce a limited number of copies by contacting CTIA at: CTIA Certification Program th Street, NW, Suite 600 Washington, DC certification@ctia.org Telephone: CTIA The Wireless Association. All rights reserved. CTIA has granted a license to CTIA Authorized Testing Laboratories to use this Test Plan for the sole purpose of testing wireless products for the CTIA Certification Program. Any reproduction or transmission of all or part of CTIA's Test Plan, in any form or by any means, electronic or mechanical, including photocopying, recording, or any information storage and retrieval system, without the prior written permission of the CTIA is unauthorized and strictly prohibited. Test laboratories that are not CTIA Authorized Testing Laboratories and wish to use CTIA Test Plans must receive written permission from CTIA prior to such use.

3 TABLE OF CONTENTS SECTION 1 INTRODUCTION PURPOSE SCOPE APPLICABLE DOCUMENTS GPP2 / TIA REFERENCE MATRIX TEST OVERVIEW EUT - EQUIPMENT UNDER TEST (MOBILE STATION) MOBILE STATION DOCUMENTATION DEFINITIONS BAND CLASS DEFINITION REVISION HISTORY TEST CASE EXCEPTIONS...10 APPENDIX A - C.S0011-B - RECOMMENDED MINIMUM PERFORMANCE STANDARDS FOR CDMA2000 SPREAD SPECTRUM MOBILE STATIONS...10 APPENDIX B C.S SIGNALING CONFORMANCE TEST SPECIFICATION FOR CDMA2000 SPREAD SPECTRUM SYSTEMS...11 APPENDIX C C.S RECOMMENDED MINIMUM PERFORMANCE STANDARDS FOR CDMA2000 HIGH RATE PACKET DATA ACCESS TERMINAL...11 APPENDIX D C.S0033-A - RECOMMENDED MINIMUM PERFORMANCE STANDARDS FOR CDMA2000 HIGH RATE PACKET DATA ACCESS TERMINAL...12 APPENDIX E C.S RECOMMENDED MINIMUM PERFORMANCE SPECIFICATION FOR C.S SPREAD SPECTRUM MOBILE STATIONS...12 APPENDIX F C.S SIGNALING CONFORMANCE SPECIFICATION FOR CDMA2000 WIRELESS IP NETWORKS...12 APPENDIX G C.S SIGNALING CONFORMANCE TEST SPECIFICATION FOR CDMA2000 HIGH RATE PACKET DATA AIR INTERFACE...13 APPENDIX H C.S SIGNALING CONFORMANCE TEST SPECIFICATION FOR OVER-THE-AIR SERVICE PROVISIONING...13 APPENDIX I C.S SIGNALING CONFORMANCE TEST SPECIFICATION FOR SHORT MESSAGE SERVICE...13 APPENDIX J C.S DATA SIGNALING CONFORMANCE TEST SPECIFICATION FOR CDMA2000 AIR INTERFACE...13 APPENDIX K C.S SIGNALING TEST SPECIFICATION FOR MOBILE STATION EQUIPMENT IDENTIFIER (MEID) SUPPORT FOR CDMA2000 SPREAD SPECTRUM SYSTEMS...14 April 2009 i Revision 5.4.1

4

5 Section 1 Introduction 1.1 Purpose The purpose of this Test Plan is to define the CTIA Certification Program test requirements for evaluating CDMA Cellular/PCS Mobile Stations in a laboratory environment. The CDMA Certification Forum (CCF) Certification Test Plan for cdma2000 Mobile Stations (CCF-L) is used. Exceptions are noted in this document. Tests are performed against automated commercial test equipment in a laboratory environment. The purpose of these tests is to seek the absolute highest possible level of test coverage under automated, repeatable and fully controllable test conditions. To the maximum extent practical, testing requirements are based upon industry standards referenced in the CCF-L test plan. The most recently published version of the CCF-L test plan at the time the Equipment Under Test (EUT) is entered into the Certification Database shall be used. This Test Plan is part of a CTIA Certification Program as described in a separate document entitled CTIA Certification Program Management Document. (PMD). The PMD defines the full criteria, in addition to laboratory conformance tests, that must be met for CTIA Certification. 1.2 Scope This Test Plan defines general requirements for minimum performance testing and signaling conformance of Mobile Stations incorporating CDMA technologies. This Test Plan does not provide specific test equipment configurations or detailed test procedures by which to execute Certification testing. Such documentation and procedures must be presented by the CTIA Authorized Testing Laboratory (CATL) as part of the CATL authorization process and subsequently maintained and employed by the CATL to remain authorized to conduct Certification testing. This Test Plan does not include the test requirements or test methodology for other Mobile Station standards or technologies (e.g., GSM, UMTS). Aspects of multiple CTIA Test Plans are merged in those cases where a product supports a blend of multiple technologies. April Revision 5.4.1

6 1.3 Applicable Documents The following documents and published addendums are applicable to this Test Plan: CTIA Certification Program Management Document, Revision 5.0, October 2007, CTIA. CDMA Certification Forum (CCF) Certification Test Plan for cdma2000 Mobile Stations TG-CCF_LTest Plan Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations - 3GPP2 C.S0011-C Signaling Conformance Test Specification for cdma2000 Spread Spectrum Systems - 3GPP2 C.S Recommended Minimum Performance Standards for cdma2000 High Rate Packet Data Access Terminal - 3GPP2 C.S Recommended Minimum Performance Standards for cdma2000 High Rate Packet Data Access Terminal - 3GPP2 C.S0033-A Recommended Minimum Performance Specification for C.S Spread Spectrum Mobile Stations - 3GPP2 C.S Signaling Conformance Specification for cdma2000 Wireless IP Networks - 3GPP2 C.S Signaling Conformance Test Specification for cdma2000 High Rate Packet Data Air Interface - 3GPP2 C.S Signaling Conformance Specification for High Rate Packet Data Air Interface - 3GPP2 C.S0038-A Signaling Conformance Test Specification for cdma2000 Spread Spectrum Systems -3GPP2 C.S Signaling Conformance Test Specification for Over-the-Air Service Provisioning - 3GPP2 C.S Signaling Conformance Test Specification for Short Message Service - 3GPP2 C.S Data Signaling Conformance Test Specification For CDMA2000 Air Interface - 3GPP2 C.S0062 Signaling Test Specification for Mobile Station Equipment Identifier (MEID) Support for cdma2000 Spread Spectrum Systems -3GPP2 C.S April Revision 5.4.1

7 Recommended Minimum Performance Standards for cdma Spread Spectrum Mobile Stations, TIA-98-F, September 2005, Telecommunications Industry Association Signaling Conformance Tests for cdma2000 Spread Spectrum Systems, TIA/EIA-898 December 2001, Telecommunications Industry Association Recommended Minimum Performance Standards for cdma2000 High Rate Packet Data Access Terminal, TIA-866-1[E], January 2004, Telecommunications Industry Association Signaling Conformance Standard for cdma2000 High Rate Packet Data Air Interface, TIA-919, May 2002, Telecommunications Industry Association Recommended Minimum Performance Specification for TIA/EIA/IS Spread Spectrum Mobile Stations, TIA-916, April 2002, Telecommunications Industry Association Signaling Conformance Specification for cdma2000 Wireless IP Networks, TIA-918 "Signaling Conformance Test Specification for cdma2000 Air Interface,, TIA GPP documents can be downloaded from the web site 3GPP2 documents can be downloaded from the web site The CTIA PMD can be downloaded from CCF test plan can be downloaded from the web site 1 cdma2000 is a registered trademark of the Telecommunications Industry Association (TIA-USA) April Revision 5.4.1

8 1.4 3GPP2 / TIA reference matrix The following table is provided for reference to assist in correlating between 3GPP2 Reference Documents, and TIA Reference Documents. 3GPP2 Reference Documents Telecommunications Industry Association Reference Documents Document Detail Document Detail C.S0011-B Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations TIA-98-F Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations C.S Signaling Conformance Test Specification for cdma2000 Spread Spectrum Systems TIA-898 cdma2000 Signaling Conformance Tests C.S Recommended Minimum Performance Standards for cdma2000 High Rate Packet Data Access Terminal TIA-866-1[E] cdma2000 1x-EvDO Minimum Performance Tests C.S0033-A Recommended Minimum Performance Standards for cdma2000 High Rate Packet Data Access Terminal TIA-866-1[E] cdma2000 1x-EvDO Minimum Performance Tests C.S Recommended Minimum Performance Specification for C.S Spread Spectrum Mobile Stations TIA-916 cdma2000 Position Location Minimum Performance Tests C.S Signaling Conformance Specification for cdma2000 Wireless IP Networks TAI-918 Appendix B.2.B = cdma2000 Wireless IP Signaling Conformance Tests Appendix B.2.D = cdma2000 1x-EvDO Wireless IP Signaling Conformance Tests C.S Signaling Conformance Test Specification for cdma2000 High Rate Packet Data Air Interface TIA-919 cdma2000 1x-EvDO Signaling Conformance Tests C.S0038-A Signaling Conformance Specification for High Rate Packet Data Air Interface TIA-919 cdma2000 1x-EvDO Signaling Conformance Tests C.S Signaling Conformance Test Specification for cdma2000 Spread Spectrum Systems TIA1035 "Signaling Conformance Test Specification for cdma2000 Air Interface, C.S Signaling Conformance Test Specification for Over-the-Air Service Provisioning TIA-1044 Signaling Conformance Test Specification for Over-the-Air Service Provisioning C.S Signaling Conformance Test Specification for Short Message Service TIA-1045 Signaling Conformance Test Specification for Short Message Service (SMS)," C.S0062 Data Signaling Conformance Test Specification For CDMA2000 Air Interface TIA-1045 Signaling Conformance Test Specification for cdma2000 Data Services C.S Signaling Test Specification for Mobile Station Equipment Identifier (MEID) Support for cdma2000 Spread Spectrum Systems TIA-1084 Signaling Test Specification for Mobile Station Equipment Identifier (MEID) Support for CDMA2000 Spread Spectrum Systems April Revision 5.4.1

9 1.5 Test Overview All testing shall be conducted as described in the CTIA PMD (see Laboratory Test Procedures section) at a CATL. A current list of CATLs can be found at Products shall be submitted for testing in accordance with the instructions detailed in the CTIA Certification Program Management Document. Tests are to be conducted only if the corresponding features are supported by the mobile station. The manufacturer shall provide to the CATL a list of features supported by the mobile station. Test failures shall be handled as described in the CTIA PMD (see Test Failures section). The test report shall include the minimum information as described in the CTIA PMD (see Laboratory Reporting section) Special Results Reporting Traffic, Paging, and Pilot Channel gain settings shall be verified prior to executing any tests using a code domain analyzer. Measured numbers shall be stated in the test report next to the base station settings. 1.6 EUT - Equipment Under Test (Mobile Station) In accordance with the CTIA PMD, units for test are to be supplied with all required peripherals and accessories. In addition, any auxiliary equipment which is available as part of the product, either for installation or as an option, should be supplied. 1.7 Mobile Station Documentation All documentation associated with the installation and operation of the mobile station shall be supplied in accordance with the CTIA PMD (see Certification Testing Checklist). April Revision 5.4.1

10 1.8 Definitions Term Access Terminal Definition A device providing data connectivity to a user. An access terminal may be connected to a computing device such as a laptop personal computer or it may be a self-contained data device such as a personal digital assistant. An access terminal is equivalent to a mobile station in an IS-2000 system. Mobile Station An entity in the public cellular radio telecommunications service intended to be used while in motion or during halts at unspecified points. Mobile stations include portable units (e.g., hand-held personal units) and units installed in vehicles. April Revision 5.4.1

11 1.9 Band Class Definition The following is a list of the band classes defined in TIA-1030: Band Class 0 (800 MHz band) Band Class 1 (1900 MHz band) Band Class 2 (TACS band) Band Class 3 (JTACS band) Band Class 4 (Korean PCS band) Band Class 5 (NMT-450 band) Band Class 6 (IMT-2000 band) Band Class 7 (700 MHz cellular band) Band Class 8 (1800 MHz band) Band Class 9 (900 MHz band) Band Class 10 (Secondary 800 MHz band) Band Class 11 (400 MHz European PAMR band) Band Class 12 (800 MHz PAMR band) April Revision 5.4.1

12 1.10 Revision History Test Plan for CDMA Mobile Stations Date Revision Purpose/Change January 1998 Draft 1.0 Issued For Comments February 1998 Draft 1.1 Issued For Comments June 1998 Release 1.2 Changed to reflect IS-98-B Included CDMA Environmental Tests Calibration Procedure Added Added Analog Call Setup Modified CDMA Results Tables Added Thermal Shock January 1999 Draft 1.3 (not released) General Reformat Simplified Table/Figure Referencing Extensive Review and Update of Existing Procedures November 1999 Release 2.0 (not released) CDMA testing now reflects use of TAS hardware and software Added support for 8924C idle and soft handoff tests All tests now reflect TIA/EIA-98-B General revision of procedures February 2000 Release 2.1 CDMA Authentication added Acoustics reflect new B&K 6713 Editorial changes made November 2001 Release 3.0 Certification program restructured Replaces previously titled Test Plan for 800 MHz AMPS & Cellular/PCS CDMA Wireless Subscriber Stations October 2002 Release 3.1 Updated applicable documents to latest specifications Added acronyms table Updated 1x and position location tests to reflect latest specifications Added TIA/EIA-898 references to signaling conformance tests Identified signaling conformance tests as informational-only Clarified system performance tests and added CDG35 test matrices Editorial changes November 2003 Release 3.2 Updated reference to document Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations to Version TIA/EIA-98-E Deleted reference to TIA/EIA-98-E, Ballot Version Updated PMD reference to Rev. 3.0 Corrected TIA-919 title Revised signaling conformance test requirements Provided roadmap for future test requirements April 2004 Release 4.0 Expanded Test Coverage, including 1x-EvDO & Position Location Removed test cases; updated test matrices; added hybrid test Added Test Process section and safe-for-network test report format Identified safe for network test cases in test matrices Revised test coverage to reflect CATL input on test capability Clarified radiated test coverage requirements Allowed testing per spirit of CDG References 35 & 64 Updated PMD reference to Rev. 3.1 April Revision 5.4.1

13 Date Revision Purpose/Change October 2004 Release 4.1 Updated test matrices Updated document references Clarified two-part test process Updated position location testing Renamed hybrid test to TIA-916 test and updated January 2005 Release 4.2 Updated test matrices May 2005 Release 4.3 Updated test matrices October 2005 Release 4.4 Updated test matrices Updated PMD reference to Rev. 4.2 Added Temperature Designator October 2006 Release 5.0 Reformatted to reference CCF-L Certification Test Plan November 2006 Release 5.1 Revised Environmental test requirements Clarified CCF-L test plan version requirements Updated PMD reference to Rev. 4.3 November 2006 Release 5.2 Added Environmental test requirements back into requirements for C.S0033 December 2006 Release 5.3 Added requirement to test all band classes supported by the device Fixed incorrect reference to C.S Took out test cases 10.6, 13.5 and 4.1 in C.S Updated PMD reference to Rev. 4.4 January 2008 Release 5.4 Added 3GPP2 references C.S0043-0, C.S0060-0, C.S0061-0, C.s0062, C.S and OMA-ETS-MMS-V1_ April 2009 Release Deleted 3GPP2 reference OMA-ETS-MMS-V A - Enabler Test Specification for MMS and ME conformance test for R- UIM 3GPP2 C.S0048. Deleted requirement that for CTIA Certification, the device must be tested in all bands supported by the product. April Revision 5.4.1

14 1.11 Test case exceptions Below is a list of Test Cases that differ between the CTIA Certification requirements, and the CCF Certification requirements. In order to fulfill CTIA Certification requirements, these exceptions must be followed in addition to testing to the CCF-L Test Plan. Appendix A - C.S0011-B - Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations C.S0011-B 1.3 Fundamental Channel Test Mode 1 (F/R RC1) X Fundamental Channel Test Mode 2 (F/R RC2) X Fundamental Channel Test Mode 3 (F/R RC3) X Supplemental Channel Test Mode 3 (Fwd RC3) X Fundamental Channel Test Mode 4 (F-RC4 & R-RC3) X Supplemental Channel Test Mode 4 (Fwd RC4) X Fundamental Channel Test Mode 5 (F-RC5 & R-RC4) X Supplemental Channel Test Mode 5 (Fwd RC5) X Band Class 0 (800 MHz band) X Band Class 1 (1900 MHz band) X 5 2 Environmental Requirements 5.1 Temperature and Power Supply Voltage 5.2 High Humidity 5.3 Vibration Stability 5.4 Shock Stability 2 For CTIA Certification, Environmental tests require that Low/Mid/High Channels be tested. April Revision 5.4.1

15 Appendix B C.S Signaling Conformance Test Specification for cdma2000 Spread Spectrum Systems C.S Miscellaneous Air Interface Tests Logging Tests X 4 Power Control Tests Hardware Flow Control X 13 High Speed Packet Data Mobile Station Originated Short Data Burst X Mobile Station Terminated Short Data Burst X 14 Over-The-Air Services 14.2 OTAPA Service Request Processing for a Mobile Station in Mobile Station Idle State X 14.4 OTAPA Service Request Processing Interrupted by User Action X Appendix C C.S Recommended Minimum Performance Standards for cdma2000 High Rate Packet Data Access Terminal C.S Environmental Requirements 10.1 Temperature and Power Supply Voltage X 10.2 High Humidity X 10.3 Vibration Stability X 10.4 Shock Stability X 3 Tests, , are not required 4 For CTIA Certification, Environmental tests require that Low/Mid/High Channels be tested. April Revision 5.4.1

16 Appendix D C.S0033-A - Recommended Minimum Performance Standards for cdma2000 High Rate Packet Data Access Terminal C.S0033-A 5 Environmental Requirements 7.1 Temperature and Power Supply Voltage X 7.2 High Humidity X 7.3 Vibration Stability X 7.4 Shock Stability X Appendix E C.S Recommended Minimum Performance Specification for C.S Spread Spectrum Mobile Stations C.S No discrepancies N/A Appendix F C.S Signaling Conformance Specification for cdma2000 Wireless IP Networks C.S No discrepancies N/A 5 For CTIA Certification, Environmental tests require that Low/Mid/High Channels be tested. April Revision 5.4.1

17 Appendix G C.S Signaling Conformance Test Specification for cdma2000 High Rate Packet Data Air Interface C.S No discrepancies N/A Appendix H C.S Signaling Conformance Test Specification for Over-the-Air Service Provisioning C.S No discrepancies N/A Appendix I C.S Signaling Conformance Test Specification for Short Message Service C.S No discrepancies N/A Appendix J C.S Data Signaling Conformance Test Specification For CDMA2000 Air Interface C.S0062 No discrepancies N/A April Revision 5.4.1

18 Appendix K C.S Signaling Test Specification for Mobile Station Equipment Identifier (MEID) Support for cdma2000 Spread Spectrum Systems C.S No discrepancies N/A April Revision 5.4.1