US-IP2. Monitoring Receiver

Transcription

1 US-IP2 Monitoring Receiver (and IP receiver card) Programming Manual 28 / 01 / 2014

2 CONTENT 1. INTRODUCTION SYSTEM STRUCTURE FIRST STEPS...4 Connectors and LED signals SYSTEM PROGRAMMING WITH PC SOFTWARE TROUBLESHOOTING US-IP2 TESTING FIRMWARE UPGRADE AND OTHER FUNCTIONS SYSTEM MESSAGES COMPATIBILITY TECHNICAL DATA

3 1. INTRODUCTION Thank you for choosing our product. This modern and reliable monitoring receiver not only guarantees the highest level of security, but also it is a useful colleague in the life of every monitoring company, because of its user-friendly handling and intelligent functions. To use the highest range of provided functions please read carefully the Installer Manual. For the confident programming and secure usage please keep all warnings in Installer Manual, with highly focusing to security directions. Note: If you use this unit as an IP receiver card, please use the manual of base receiver. 3

4 2. SYSTEM STRUCTURE The US-IP2 monitoring receiver is ideal and cost-effective solution to build-up a monitoring station, where transmission is sent only through IP / GPRS channel. Device has compact size and excellent parameter setting possibilities. The incoming IP communication might be monitored according to client accounts. It provides prominent protection level for the reliable and secure operation. The card version device can be be built into the base receiver unit. With combination of a suitable monitoring software it guarantees not only reliable signal transmission, but also easy to use operator interface. 3. FIRST STEPS Please unpack the device carefully and please check is there any damage on that caused by transport. If there is any obvious damage do not switch on the device, please call the distributor. The basic package contains the following units: US-IP2 monitoring receiver USB cable for PC connection 12 VDC power supply set Installer Manual Before mounting the device to its operation environment, receiver test is recommended. 4

5 Connectors and LED signals There are the following connectors on the backside of the receiver: Power supply connector: 12 VDC power supply connector (always use the original power supply unit provided by manufacturer). Note: In case of the failure of main power supply unit, the device is able to operate with power received through USB cable (if USB current is suitable). But long term usage without main power supply unit is not recommended. Ethernet connector: 100 Mbit Ethernet connector for network cable. Mini USB connector: To connect of the USB port of monitoring PC (serial comm). RS232 connector (only in newer version IP2 receiver): To connect to monitoring PC (serial communication). There are the following connectors on the front side of the receiver: POWER LED: It lights in blue if device is ready to use. IP LINK LED: It lights green if there is connected network. There is slow red flashings if network cable is unplugged. Quick red flashings mean received events. Note: If buzzer is enabled, it sounds with short signals (about 2 beep / sec frequency) if the network connection is unplugged. PC LINK LED: It lights green if there is serial connection (USB) with monitoring software. If there is no connection with monitoring software, this LED is off. Note: If buzzer is enabled, it sounds with short signals (about 4 beep / sec frequency) if the connection with monitoring software is failed. RECEIVER EVENT LED: Amber led flashing means if there is received event through IP network. RECEIVER TROUBLE LED: Slow red flashings show the receiver errors (such as power supply error, monitoring software connection error, IP network error). Note: The buzzer (if enabled) is continuously active during programming. IP LINK, RECEIVER EVENT and RECEIVER TROUBLE leds are blinking during programming. 5

6 4. SYSTEM PROGRAMMING WITH PC SOFTWARE To use the monitoring receiver with monitoring PC connect the mini USB port of receiver to the USB port of the monitoring PC. Driver installation is automatic (from Windows 7). After this the appropriate monitoring software settings should be done (it means usually the serial port and baud rate settings). The process is the following in PC software (example, different in every software type): Start monitoring software Start Setup part and log in (ID: 1, Password: 1) Setup menu Hardware Setup Digital Receiver #1. In pop-up window basically only Receive and process incoming messages option should be enabled, then set the proper COM port (checking in Windows OS: Control Panel / Hardware / Device Manager), then apply changes. After this the COM ERROR should be restored in monitoring receiver, and receiver events are displayed on monitoring software screen. Note: To connect US-IP2 card to monitoring software set Baud Rate value to in monitoring software settings. 6

7 In normal case programming of the monitoring receiver unit can be done through USB (serial) port. After completing appropriate IP settings programming can be done through Ethernet network as well. Please use Terminal software for programming. The programming steps are bellow: 1. Please start Terminal software. 2. Choose the ET (settings) file according to the device what you want to program: - IP.et US-IP2 Ethernet receiver card programming 3. In Communication / Port Settings menu set the communication port / IP address for programming. 4. With Communication / Read Data menu you can read stored settings from receiver. The highlighted firmware version means the following (hexadecimal format): C 12 (2012) A 10 (October) 02 2 (Second day) 5. Please execute the required settings in Terminal software. Note: The software functions are shown in Terminal help menu. 7

8 6. Click to Communication / Write Data menu to send the modified settings to receiver. Note: During data reading (and sending) receiver firmware version can be checked. 5. TROUBLESHOOTING TROUBLE: Any abnormal operation in functions during the usage of the device. SOLUTION: Firmware upgrade with the newest firmware file usually solve these kind of problems (see Firmware update part in manual). TROUBLE: No connection between monitoring PC and receiver unit. SOLUTION: Check the cable plugging in PC side and in receiver side as well. In monitoring PC Control Panel / Hardware / Device Manager application you can check which COM port appears / disappears in device list during plug / unplug US-IP2 cable. Please check whether COM port setting is correct in monitoring software. Baud rate should be set to in monitoring software settings. TROUBLE: After proper IP configuration receiver events are not coming through IP. SOLUTION: Don't forget to allow used ports in rooter (Port forward menu in rooter). TROUBLE: There are strange internal messages in receiver with 0000 client account. SOLUTION: It is possible that any of the external device (alarm control panel) has 0000 client account. Never use 0000 client account in alarm control panel side. 8

9 TROUBLE: The receiver unit freezes because of any external reason. SOLUTION: Unplug power supply cable and USB cable at the same time, then plug it back. It means hardware reset of the receiver. 9

10 6. US-IP2 TESTING When all setting is finished it is possible to test US-IP2 unit. Testing is also useful to test data sending from an external installation place. The testing software in the given local network can help a lot to check monitoring transmission and find the reason of possible problems. For test please use ipt.exe software in the following way: 1. Enter the IP address or Domain name of the monitoring station. 2. Set the ports for communication with monitoring station (Receive Port = Monitoring transmission port; Shell (Telnet) Port = Remote programming port; Web Server Port = Event list access through web browser port). 3. After click to Test button it can be seen that test is successful (PASS) or not (FAIL). 4. If you want you can change the program settings in Options part: - Enable TCP Test Report = TCP connection test with test message; - Enable UDP Test Report = UDP connection with test message; - Invisible TCP/UDP Test = Test message can't be seen on receiver; 10

11 - Enable AES Crypted Test Report / AES Key = Test of AES encryption function. 11

12 Received events in US-IP2 can be checked easily with a simple web browser access. For this IP address (and port if it is different from 80) of US-IP2 unit should be typed in a web browser (Internet Explorer recommended). Then receiver HTTP page can be seen. Note: For the operation of event list review through web browser the IP ADDRESS and HTTP PORT should be enabled in rooter as well. In Accounts menu you can check the accounts for IP monitoring (if enabled). Additionally you can set individual communication monitoring settings for each user. Event Log Display list of received events. Accounts IP communication monitoring status check. Monitoring period, test code monitoring, encryption might be configured individually for each user. Settings Generally used settings such as: date/time settings, event list export, account list import/export, logo upload, web data file upload (after firmware upgrade). Note: Default password to access settings menu: HD View To better display in wide screen monitor, more parameters. 12

13 7. FIRMWARE UPGRADE AND OTHER FUNCTIONS It is recommended to upgrade regularly firmware of the unit to use new functions and eliminate possible bugs. Firmware upgrade can be done by the following steps: 1. Get the latest firmware files from your distributor (ip.ipx file). 2. Save settings from the IP card planned to update with Terminal software (please check 4. System programming with PC software chapter). Please close monitoring software if it is running. 3. Start Receiver Uploader program for firmware upgrade. 13

14 4. Choose item IP Card for upgrade (1. STEP), then NEXT. 14

15 5. The following window will pop up if you use IP Card update. 6. Choose the COM port where IP card is connected. Note: The baudrate should be set to in case of IP card update. IP card update through Ethernet is only possible through local network. 7. After clicking to Connect menu, then Load File menu you should select ip.ipx firmware file for update. 8. Upgrade process can be started with Update button. Click To Disconnect button at the end of update proccess. 9. Do not forget to send back the saved IP card settings at the end of the upgrade (please check 4. System programming with PC software chapter). 10. To use new functions it might be required to get the latest Terminal software with the newest ET (setup) files please download and use newest version. 15

16 Web browser menu of IP card can only be uploaded on the web browser site of IP card. Upload is possible in Data Upload menu. If the web browser site cannot be uploaded from any reason, you can use IP address then /mpfsupload command for data upload (for example: /mpfsupload) of ip.bin file. Default upload password:

17 8. SYSTEM MESSAGES System Message Code Description DATAFILE MODIFY B1 IP receiver card web browser data file modified SETTING MODIFY B2 IP receiver card settings changed PROGRAM MODE PROGRAM END COM ERROR COM RESTORED B3 B4 B5 B6 IP receiver card programming through serial port / IP network IP receiver card programming through serial port / IP network end IP receiver card communication error on USB port (with monitoring software) IP receiver card communication restore on USB port (with monitoring software) TCP/IP ERROR B7 IP receiver card TCP/IP network error TCP/IP RESTORED B8 IP receiver card TCP/IP network restored TIME/DATE SET B9 IP receiver card date and time set FIRMWARE UPDATE B0 IP receiver card firmware updated LAN ERROR BB IP receiver internal LAN connection (gateway) test failed LAN RESTORED BC IP receiver internal LAN connection (gateway) test OK RECEIVER RESET BD IP receiver card restarted IP WAN ERROR BE IP receiver external WAN connection test failed IP WAN RESTORE BF IP receiver external WAN connection test OK BATTERY ERROR 11 Receiver internal battery voltage error BATTERY OK 12 Receiver internal battery voltage restore RECEIVER STOP 19 Receiver shutdown before planned restart REC. OVERHEAT 33 Receiver overheat event IPFORW ERROR 51 Communication error in IP event forwarding IPFORW OK 52 Communication restore in IP event forwarding CPM COMM ERROR 53 Communication trouble with receiver CPM bus CPM COMM OK 54 Communication restore with receiver CPM bus IPSERVER STOP 57 IP receiving server stop in receiver IPSERVER START 58 IP receiving server start in receiver 17

18 AC ERROR 81 AC error in receiver power supply AC RESTORE 82 AC restore in receiver power supply IP ERROR 1692 There is no IP communication from the given client account within the defined time range (comm. lost) 18

19 IP RESTORE 3692 Z0 Z9 IP communication restored for the given client account where communication was lost The given client account was deleted on web browser The given account was modified on web browser Note.: System messages are sent with 0000 client account (except IP ERROR / IP RESTORE messages, which are sent with the given client account where IP communication was lost). 9. COMPATIBILITY US-IP2 receiver is compatible with the following communicators and monitoring software types: Monitoring software The device can work with the most generally used monitoring software packages, please consult with your distributor about recommended monitoring PC software. IP communicators Please consult with your distributor about recommended devices. GPRS communicators Please consult with your distributor about recommended devices. 19

20 10. TECHNICAL DATA Product Power supply Maximum current consumption Event buffer Monitored IP devices Ethernet connector Operating temperature Sizes (W / L / H) Weight US-IP ma about 250 ma up to events up to accounts 100 Mbit 10 C / +30 C 40% relative humidity 110 x 190 x 35 mm 300 g 20