AT61 GSM Text Auto Dialer Manual

Transcription

1 Introduction A6 GSM ext Auto Dialer is an advanced component that when triggered it will send a text message up to 3 different telephone mobile numbers. If the A6 dialer is connected to a Force0 intruder control panel then you have the additional feature to be able to ARM and DISARM via short message text message on your mobile phone. Compatible Networks: Vodafone, EE/Orange, O2 Feature. You can register a maximum three mobile numbers 2. one master code (default pin: 023) to setup/program the dialer 3. amper protect function. 4. Modify pin 5. SMS COMMAND to set control panel going to Arm and disarm mode (Force 0 Panels only) 6. Eight terminals (five input for trigger as: Intruder, PA, ABOR, SE+ and Fire, two input for power supply DC 3V + and DC 3V -, one output terminal PS for to control ARM or DISARM for control panel. 7. GSM receiving signal level indicated on LCD display. Challenger_A6 _Instructions_Rev0

2 Wiring diagram ). he supplied relay module will need to be used with security control panels without communicator outputs. Below diagram illustrating connection to a Force-0 control panel. Force-0 Alarm Control Panel GSM Dialler External F Board IMPORAN NOE: o enable the remote text function for Arm/Disarming and notification of Set/Unset with a compatible Force0 Control Panel, then the below programming options will need to be configured from the Engineering menu on the Force 0 control panel ).Enable below features at Force-0 control panel -[Setup system]->[flag2]->[key switch]->select ON -[Setup system]->[flag2]->[strobe on set]->select ON 2).Once the GSM dialer (mobile phone is set) and is powered on, the preset mobile phone will receive below message SE off FIRE rigger ABOR rigger PANIC rigger 3).If amper or Panic Alarm (PA) is triggered under mode, the preset mobile phone will receive below message INRUDER rigger 4).All trigger of Alarm, amper, Panic Alarm (PA) under SE mode (armed status) will send message of INRUDER rigger 2 Challenger_A6 _Instructions_Rev0

3 2). Connection with Force0 Main Panel with built-in communicators outputs (AP0LEDC, APLEDC, APLCDC) Usage How to setup Force0 Control Panel Key switch function Operate Control panel, setup key switch function Enter Manager program mode Press MANAGER MENU Setup Codes? 3 access. key to require the Manage to authorize Engineer MANAGER MENU Authorise Engr? to accept. It will give a 3hr window to operate the Engineer operation mode. to accept, the accept tone will be generated. Engr Authorised for 3 hours MANAGER MENU Set Chime Zones? RES E to go back mode. 00:26:5 08-Aug Input 4-digit Engineer code and go to 3 LC ENGINEER MENU Setup Programs? Challenger_A6 _Instructions_Rev0

4 Engineer operation widow within 5 seconds. 5 keys go into Setup System function. SEUP SYSEM Flags? 2 keys go into Setup Flags 2 SELEC FLAG 2 Key switch? key accept be selected flag. Key switch OFF or OMI key to toggle ON/OFF, Key switch ON to save. SELEC FLAG 2 PS as Doorbell? RES E to go back mode. 00:26:5 08-Aug GSM Dialer Power on Message NOE: Insert Sim card before applying Power Display software version. LCD GSM DIALER Version: V3.9x Initial GSM module. For initial power will take approx minute to setup GSM module. Init GSM Module. Init GSM Module When no SIM, display SIM not inserted SIM not inserted GSM module has finished, normal display: 08:00 0-Dec When no SIM card inserted or incompatible network: 08:00 0-Dec X 4 Challenger_A6 _Instructions_Rev0

5 When the SIM card requires PIN, or poor signal quality: 08:00 0-Dec Defaulting Panel to Factory Settings You will change the value of all parameters to factory default. CAUION: All configurations of the panel are restored to factory default conditions. o default to factory settings: Power down the GSM LCD Dialler. and hold Power up. 9 keys. LCD GSM DIALER Version: V3.9x Wait about 3 seconds, LCD display Reset NVM OK Reset NVM OK Release press keys and system initial GSM module. Init GSM Module. How to Change USER CODE using self-user code System in Day mode or system in SE mode. 08:00 0-Dec 08:00 0-Dec o enter User Menu Press * * * * Input new code (4-digit) Enter your code ***** to save and return to Day mode. Enter new code **** If the 4-digits is the same as old, then display Duplicate Code press any key return to Day mode and no change code. 08:00 0-Dec Duplicate Code! 5 Challenger_A6 _Instructions_Rev0

6 How to Set up the system 08:00 0-Dec he full menu structure for the panel can only be accessed while in Master Program Mode. he structure is shown in the following table: MENU OPIONS Register mobile 2 Set up codes 3 View Event log 4 Set up system How to go into Master Program Mode System work in Day mode or system in SE mode. 08:00 0-Dec 08:00 0-Dec Go into Master Menu Press Master Menu display. Enter your code ***** MASER MENU Register Mobile? =Register Mobile here are 3 Mobile Number can be created in the system,, all are 6-digit and can be set. = Mobile Number, 2 = Mobile Number 2, 3 = Mobile Number 3 How to change Mobile number keys go into Setup Codes function. 3 or OMI or key to select a Mobile Number that you want to program. Note: = mobile number, 3 = mobile number 3 MASER MENU Register Mobile? REGISER MOBILE Mobile Number? 6 Challenger_A6 _Instructions_Rev0

7 key to accept and go into set the mobile number. SEUP MOBILE NUM Set new mobile number: Input new mobile number: SEUP MOBILE NUM to save. or Press key will without change the mobile number and to go to modify next mobile number, if the number is Mobile Number 3, it will leave Register Mobile and go to next menu Setup Codes REGISER MOBILE Mobile Number 3 to return to master menu. MASER MENU Setup Codes? How to delete Mobile number keys go into Setup Codes function. MASER MENU Register Mobile? 3 or OMI or key to select a Mobile Number that you want to set. Note: = mobile number, 3 = mobile number 3 REGISER MOBILE Mobile Number? key to accept and go into set the mobile number. SEUP MOBILE NUM _ OMI key to clear the mobile number display. SEUP MOBILE NUM _ to accept delete the mobile number. or Press key will without change the mobile number and to go to modify next mobile number, if the number is Mobile Number 3, it will leave Register Mobile and go to next menu Setup Codes REGISER MOBILE Mobile Number 3 to return to master menu. MASER MENU Setup Codes? 2= Setup Codes here are 4 user codes can be created in the system, all are 4-digit and can be set to any number from 0000 to he access codes ensure that only authorized users can operate the system. 7 Challenger_A6 _Instructions_Rev0

8 = user, 2 = user 2, 3 = user 3, 4 = master User User 3 codes: he user to user 3 codes have the same operation for testing and Setting and Unsetting, changing their own code. Master code o operate the alarm system you will need to use a code. A code is 4 digits long, and can be any number from 0000 to By default master code is but you should change this as soon as possible. How to change User Code his option allows each of the users to be given a code. keys go into Setup Codes function. 4 or OMI or key to select a code that you want to set. Note: =user, 3 = user 3, 4 = master to accept and go into set the user. 2 key to select Change Code function. key go into Change Code function. MASER MENU Setup Codes? SELEC CODE User? SEUP CODE Change Code? USER CODE **** If no code programmed, then display Input new code (4-digit) USER CODE.... Duplicate Code to save. If the 4-digits is the same as old, then display press any key to leave, it goes to Delete Code Duplicate Code! key will without change the code and exit. key to return to master menu. SEUP CODE Delete Code? How to delete User Code 2 keys go into Setup Codes function. MASER MENU Setup Codes? 8 Challenger_A6 _Instructions_Rev0

9 4 or OMI or key to select a code that you want to set. Note: =user, 3 = user 3, 4 = master to accept and go into set the user. SELEC CODE User? 2 key to select Delete Code function. SEUP CODE Delete Code? key will go into delete the user code function. Delete the Code? Press PG for yes key will delete the user code or press key to cannel and go to modify next code. If the code is Master codes, it will leave Setup Codes and go to next menu View Event Log. Press to return to master menu. SELEC CODE Master Code? MASER MENU View Event Log? 3 = View Event Log he event log gives displays of all the events that have taken place. he events are organised by date and time. Up to 43 events can be stored in the memory. When the log reaches 43 events any new events will overwrite the oldest events. he system is known as FILO (First In Last Out). o view the event log: Under Master Menu 3 key to select View Event Log function. MASER MENU View Event Log? to accept and most recent event shown first. FIRE rigger 08:2 05-Dec 43 View older event log using OMI or 2 key. View newer event log using or 3 key. PANIC rigger 08:2 04-Dec 42 FIRE rigger 08:2 05-Dec 43 View oldest event log using key. INRUDER rigger 08:08 0-Dec 0 View newest event log using 4 key. 9 FIRE rigger 08:2 05-Dec 43 Challenger_A6 _Instructions_Rev0

10 9 to select clear all alarm events. Clear Event Log Press PG for yes or Press to accept. to cancel and go to next menu Setup System. MASER MENU Setup System? 4 = How to Setup System How to Setup Set ime he time can be modified in hours, minutes in the format HH:MM. you must set it correctly, or else System will generate an error tone and not save the changes. 4 keys go into Setup System function. MASER MENU Setup System? SEUP SYSEM Set ime? to select Set ime function. Set ime HH:MM 00:00 set new time to 2:02 to accept. Display current time number keys. Set ime HH:MM 2:02 MASER MENU Set Date? to save it and clear second time, or press to cancel, it will exit and go to Set Date. How to Setup Set Date he date can be changed in day, month, year format DD/MM/YY. he method of set date is the same as how to set time. e.g. Set current system date: MASER MENU Setup System? Challenger_A6 _Instructions_Rev0

11 4 keys go into Setup System function. 2 to select Set Date function. to accept, display current date. Enter system date: Day/Mon/Year(6-digits) SEUP SYSEM Set Date? Date: DD/MM/YY 25/04/ number keys. Date: DD/MM/YY 28/04/7 to save it, or press to cancel, it will exit and go to Reset NVM?. SEUP SYSEM Reset NVM? How to Restore to factor value using menu You will change the value of all parameters to factory default value when you set it. CAUION: All configurations of the panel are restored to factory default conditions. o default to factory settings: 4 keys go into Setup System function. MASER MENU Setup System? 3 to select Reset NVM function SEUP SYSEM Reset NVM? go into Reset NVM function. to accept and restore to factory setting value. Reset NVM Press PG for yes MASER MENU Register Mobile? Finished and return to next option. How to Exit Master Program Menu key return to top of Master menu. key to exit Master program mode, return to Day mode, and two accept beep sound are heard. MASER MENU Setup Codes? 08:00 0-Dec Challenger_A6 _Instructions_Rev0

12 How to ARM or DISARM Mode Note: Make sure the Force0 Control Panel Key switch function is ON. ARM mode, send a SMS text message to the A6 dialer telephone number as following (case insensitive): User pin code (4-digital) + ARM (arm) e.g. 023 ARM DISARM mode, send a SMS text message to the A6 dialer telephone number as following (case insensitive): User pin code (4-digital) + DISARM (disarm) e.g. 023 disarm GSM send SMS format to mobile as following: Action event SMS content Note ARM action* Mobile number + release on Mobile number Sent SMS ARM command. DISARM action* Mobile number + release off Mobile number Sent SMS DISARM command. FIRE input FIRE trigger PA input PANIC trigger IN input INRUDER trigger SE high level input* SE On SE low level input* SE Off ABOR input ABOR trigger * available for control panel without communicators Due to our policy of continuous improvement we reserve the right to change specification without prior notice. Errors and omissions accepted. hese instructions have been carefully checked prior to publication. However, no responsibility can be accepted by Challenger Security Products for any misinterpretation of these instructions. Distributed by: CHALLENGER SECURIY PRODUCS 0 SANDERSONS WAY, BLACKPOOL, FY4 4NB enquiries@challenger.co.uk Website: 2 Challenger_A6 _Instructions_Rev0