GAT MT 010. Hand-Held Terminal MANUAL. Version 1.2 English

Transcription

1 Hand-Held Terminal GAT MT 010 Data exchange with the offline terminals and locks - GAT ST GAT ST GAT ST TAC IND MANUAL Version 1.2 English Configuration of the offline terminals and locks Booking evaluation Internal clock quartz-operated USB interface RS 232 for connection of the GAT ST 210, 220, 225, TAC IND Gantner Access Technologies. Security. Efficiency. Comfort.

2

3 Copyright ,, Schruns (Austria). Copyrights: Operating instructions, manuals and software are protected by copyright. All rights are reserved. Copying, duplication, translation, installation in any electronic medium or machine-readable form in whole or in part is prohibited. The sole exception is represented by creation of a back-up copy of software for own use as a safeguard, so far as this is technically possible and recommended by us. Any infringement will render the party committing such infringement liable to compensation payment. Liability: Any claims against the manufacturer based on the hardware or software products described in this manual shall depend exclusively on the conditions of the guarantee. Any further-reaching claims are excluded, and in particular the manufacturer accepts no liability for the completeness or accuracy of the contents of this manual. The right is reserved to make alterations, and alterations may be made at any time without prior notice being given. Trade Marks: Attention is drawn at this point to markings and registered trade marks used in this manual, in particular to the designation LEGIC which is a brand of the Kaba Group.! Important: before commencing installation, commissioning, putting into service and before any maintenance work is carried out, it is essential that the relevant warning and safety instructions in this manual are read! HB_GAT-MT010_EN_12 3

4 4 HB_GAT-MT010_EN_12

5 ! General warning and safety instructions: Dear customer, We congratulate you on having selected a product (device resp. software) of GANTNER Electronic GmbH. So that our product functions in your installation with safety and to your complete satisfaction, we take this opportunity to familiarise you with the following ground rules: 1. Installation, commissioning, operation and maintenance of the product purchased must be carried out in accordance with instructions, i.e. in accordance with the technical conditions of operation, as described in the corresponding product documentation. 2. Before installation, commissioning, operation or maintenance it is therefore essential that you read the corresponding chapter of this manual and observe its instructions. 3. If there are still some points, on which you are not entirely clear, please do not take a chance, but ask the customer adviser responsible for you, or ring the hotline. 4. Where not otherwise specifically laid down, appropriate installation, commissioning, operation and maintenance of the product is the customer s responsibility. 5. Directly on receipt of the goods, inspect both the packaging and the device resp. data carrier itself for any signs of damage. Also check that the delivery is complete (-> accessories, documentation, auxiliary devices, etc.). 6. If the packaging has been damaged in transport or should you suspect that it has been damaged or that it may have a fault, the product must not be put into service. In this case, contact your customer advisor. He will make every effort to resolve the problem as quickly as possible. 7. Installation, commissioning and servicing of our appliances must only be carried out by suitably trained personnel. In particular, electrical connections may only be made by correspondingly qualified specialists. Here, the appropriate installation provisions in accordance with the relative national Electrical Engineers construction regulations (e.g. ÖVE, [Austrian] VDE, [German]...) must be observed. 8. Where not otherwise stated, installation and maintenance work on our appliances is exclusively to be carried out when disconnected from the power supply. This applies in particular to appliances which are normally supplied by low-tension current. 9. It is prohibited to make alterations to the appliances or to remove protective shields and covers. HB_GAT-MT010_EN_12 5

6 10. Do not attempt yourself to repair an appliance after a defect, failure or damage, or to put it back into operation again. In such cases, it is essential you contact either your customer adviser or the hotline. 11. accepts no responsibility for any injuries or damage caused as a result of improper use. 12. Although every care is taken and we are continuously aiming for improvement, we cannot exclude completely the possibility of errors appearing in our documentation. therefore accepts no responsibility for the completeness or the accuracy of this manual. The right is reserved to make alterations, and we may carry out alterations at any time without giving prior notice. 13. Should you discover any fault with the product or in its accompanying documentation, or have any suggestions for improvement, you may confidently approach either your customer adviser or directly. 14. However, even if you just want to tell us that everything has functioned perfectly, we still look forward to hear from you. We wish you a successful application of our appliances. We will be pleased to welcome you as a customer again soon. Contact address / manufacturer: Montafonerstrasse 8 A Schruns/Austria Tel.: Fax: info@gantner.com Web: 6 HB_GAT-MT010_EN_12

7 TABLE OF CONTENTS TABLE OF CONTENTS INTRODUCTION... 9 System Components Short Description Terms CONFIGURATION OF THE DOORS Configure Doors Store the Door Configurations into GAT MT PROGRAMMING THE DATA CARrIERs Authorisation Configuration Programming Data Carriers (Read/Write Mode) OPERATION GAT MT Generally Connection to a Lock/Terminal Main Menu Menu Function "CONFIG" Menu Function "DATA" Menu Function "BOOKINGS" Menu Function "SYSTEM" SERVICE AND MAINTENANCE Inserting and Changing the Batteries FREQUENTLY ASKED QUESTIONS (FAQ) HB_GAT-MT010_EN_12 7

8 TABLE OF CONTENTS 8 HB_GAT-MT010_EN_12

9 INTRODUCTION 1. INTRODUCTION 1.1. System Components CD with USB driver USB Card Reader USB cable (3 m) for PC connection 2 x alkaline AA battery SD memory card (64 MByte) GAT MT 010 download cable for communication with the offline locks/terminals GAT Battery Charger SJ charging device with 4 rechargeable batteries AA Fig. 1.1 System components of the GAT MT 010 set! Alkaline batteries must not be recharged! The GAT Battery Charger SJ hast to be only used for recharging corresponding batteries (rechargeable battereis = accumulators). HB_GAT-MT010_EN_12 9

10 GAT MT 010 INTRODUCTION 1.2. Short Description The GAT MT 010 is a battery-operated hand-held terminal for use with offline access control. With the GAT MT 010 the access authorisations can be loaded into the offline terminals/locks GAT ST 210, GAT ST 220, GAT ST 225 and TAC LEGIC and all bookings can be read from the terminals/locks for later evaluation. Fig. 1.2 Systemfunktion mit GAT MT 010 Figure 1.2 shows the function of the GAT MT 010 in an offline system. The access authorisations will be defined in the PC software GAT Access or GAT Matrix and then copied to the GAT MT 010 with the supplied USB cable or the USB Card Reader (see chapter "2.2. Store the Door Configurations into GAT MT 010"). On the PC where the GAT MT 010 is connected the GAT ST220 Service and the GAT MT 010 Loader must be running and the PC resp. the service must have connection with the configuration software GAT Access/GAT Matrix. GAT Access/GAT Matrix can be installed on the same PC or on another PC/server in the network. Afterwards the authorisations can be loaded into the terminal or locks on site by using the GAT MT 010 download cable. The authorisation data carriers, which are used by the persons for identification in the access system, are defined in GAT Access/GAT Matrix and assigned to the persons. In the read/write mode the defined data for the data carriers will be transmitted to the GAT 10 HB_GAT-MT010_EN_12

11 INTRODUCTION Terminals 2500 in the system and can there be written onto the corresponding LEGIC data carriers via the connected "GAT Reader" antennas. With existing plants when connecting the MT 010 to a door lock automatically also the current reservations will become selected, these then with the next PC connection again to these to transfer Terms Authorisation Card Electronic badge used by a person for non-contact identification (via RFID reader) in an access control system. Authorisation cards can be of different types (e.g. plastic card in check card format, key tag etc.). For simplification the terms card or authorisation card respectively will be used for all kind of data carrier types. Data Carrier Electronic chip which is embedded in an authorisation card and which stores the data for the identifications. Authorisation Data The authorisation data define which persons have access authorisation on which doors (locks) to which conditions or times respectively. (Electronic) Lock Designates in this manual the electronic door locks GAT ST 220, GAT ST 225 and TAC from GANTNER. These are installed at the doors which shall be access controlled (e.g. door or turnstile). Such an electronic lock will then lock and unlock the door depending on the identification and authorisation. Unlike a terminal an electronic lock has the control electronics and unlocking mechanics installed usually in the same housing/place. Terminal A terminal is similar to an electronic lock of GANTNER but at a terminal the unlocking mechanics and the control electronics are usually installed separately. In this manual the terminal GAT ST 210 will be used for the offline access control. HB_GAT-MT010_EN_12 11

12 INTRODUCTION Door The term "door" will be used in this manual as combined umbrella term for lock and terminal. For example to configure a door means to configure the terminal or lock that is mounted at the door. Access Control System Comprehends all devices (locks, terminals), data carriers and software which are necessary to perform the access control in a facility. 12 HB_GAT-MT010_EN_12

13 CONFIGURATION OF THE DOORS 2. CONFIGURATION OF THE DOORS 2.1. Configure Doors The single doors (locks and terminals) are configured in the GAT Manager software at the PC and copied into the doors via the GAT MT 010. Following is a short description how the doors are configured. You can find a detailed help about the configuration of the doors in the online help of GAT Manager. Fig Main Window of GAT Manager Define TCP/IP Channels In the main window of GAT Manager in the door list mark the first entry "Communication Channels". Next mark the entry "TCP/IP Communication" in the device library and add it to the door list by clicking on "< Add device". HB_GAT-MT010_EN_12 13

14 CONFIGURATION OF THE DOORS Fig. 2.2 GAT Manager Communication Channels The window "TCP/IP communication settings" will be displayed automatically. Fig. 2.3 TCP/IP Communication Parameter Here the name (e.g. "Offline Doors"), the port to be used (this must not be used by the PC yet) and the IP address of the PC where GAT ST220 Service is installed, must be entered here for the new channel. If the service is installed on the same PC as GAT Manager enter "localhost". Confirm the entered data with "OK". Add New Door In the main window mark the TCP/IP channel to which you want to add a new door (here "Offline Doors"). Next select the entry "GAT Terminal 1002 (ST2xx/TAC/2500)" in the device library on the right side and click onto "< Add device". 14 HB_GAT-MT010_EN_12

15 CONFIGURATION OF THE DOORS Fig. 2.4 GAT Manager Add New Offline Door A new window will be opened where information about the new door have to be entered. Fig. 2.5 GAT Manager Settings for New Offline Door Enter a "Name" for the new door (e.g. "Offline Cylinder 100"). The address must be unique because the doors (locks and terminals) will be identified by these addresses. Mark the device type "ST2xx/TAC" in order to define a new offline door. The serial number is only of importance at online devices and can be ignored. With these steps you can ad the other doors as well. Now every door must be configured. Therefore click with the right mouse button onto an added door in the door list and select "Configuration" from the context menu. The following window will be opened. HB_GAT-MT010_EN_12 15

16 CONFIGURATION OF THE DOORS Fig. 2.6 GAT Manager Door Configuration Enter the unlocking time in seconds. This time determines for how long the terminal/lock unlocks the door after a valid identification. Mark the operation mode of the door. See also table 4.1 at the description of the configuration (chapter 4.3.2). For a GAT ST 210 it is possible to configure the two status inputs (optocouplers) by means of the button "Input Configuration". It is possible to select a function for every input and to enter a designation for the inputs. Fig. 2.7 GAT Manager Configure Inputs of a GAT ST 210 Note: A further description of the functions and settings when adding new doors can be found in the online help of GAT Manager. 16 HB_GAT-MT010_EN_12

17 CONFIGURATION OF THE DOORS 2.2. Store the Door Configurations into GAT MT 010 After the offline doors are configured, the settings are copied to a GAT MT 010 and the GAT MT 010 can then be used to transfer the settings on site into the offline doors. There are two software tools, which are used to transmit the configurations. - The "GAT ST 220 Service" is a Windows service running in the background. This service handles the communication with GAT Manager, to process and prepare the offline configuration data for transfer to a GAT MT 010. The GAT ST 220 Service is installed on the same PC/server where GAT Manager is running. - The "GAT MT 010 Loader" is a tool to copy the configuration data, prepared by the GAT ST 220 Service, into a selectable folder. These data can then be copied to a GAT MT 010 directly or via a SD card. The GAT MT 010 Loader can be installed on the network in a directory with full access rights for all network users that use the tool. It is then possible to start the tool from any PC with access to this directory. The following steps describe, how to load the offline data onto the GAT MT 010. Generally there are two different possibilities: a) 32-bit Windows: 1. Install the supplied USB driver for the GAT MT 010. Note: If the GAT MT 010 is connected the first time, a request for USB driver installation will be displayed. You can find the driver on the supplied driver CD. 2. If the GAT MT 010 is connect to the PC with the USB driver installed, the GAT MT 010 will be recognized and the configuration data will automatically be copied from the PC to the GAT MT 010. On the screen the following window is displayed: Fig. 2.8 Configuration Data are copied to the GAT MT 010 HB_GAT-MT010_EN_12 17

18 CONFIGURATION OF THE DOORS 3. After successful data transmission the following green window will appear on the screen: Fig. 2.9 Configuration Data are copied successfully to the GAT MT 010! After copying the configuration the GAT MT 010 has to be switched off and on in order to activate the copied data! b) 64-bit Windows or if the USB interface is incompatible with the GAT MT 010: 1. The USB driver doesn t work with 64-bit Windows. In this case the supplied USB card reader can be connected to the PC. No driver needs to be installed. 2. Turn the GAT MT 010 off and eject the SD card. Insert the SD card into the USB card reader. 3. Start "GAT MT 010 Loader". On the Windows status bar you will then see the icon of the loader. 4. Click with the right mouse button onto this icon. From the popup menu select the menu item "Copy data to directory..." and then select the root directory of the SD card. 5. Next you can transfer the saved data onto an SD card. 6. Insert the SD card into the GAT MT 010. Now the configuration data can be written into the locks/terminals directly on site at the respective doors. Note: In case of errors (e.g. cables not connected) a red window with a corresponding error message will be displayed. 18 HB_GAT-MT010_EN_12

19 PROGRAMMIERUNG DER DATENTRÄGER 3. PROGRAMMING THE DATA CARRIERS 3.1. Authorisation Configuration In the GAT Access software the authorisations for the persons, which shall be identified in the access control system, will be configured. A unique data carrier will be assigned to each person. In the read/write mode the authorisation information will be written directly onto the data carriers of the persons. This can be done directly at the PC with a read/write station GAT Writer or via a GAT Terminal In the last case the authorisations will be transmitted to all GAT Terminals 2500 in the access system and the data carriers can then be programmed on site directly at those terminals (see 3.2) Programming Data Carriers (Read/Write Mode) Fig. 3.1 Configuration of authorisation data carriers at GAT Terminal 2500 Hold a data carrier that shall be programmed in front of the antenna of a GAT Terminal The system recognises the data carrier and writes the corresponding access authorisation onto it. During the writing process the LED at the antenna will flash alternately red and orange. After writing the data carrier the LED will be switched to red again and the data carrier can be used from now on as access badge in the facility. Note: If the data carrier is removed too early from the antenna, before the writing process is finished, a peep sound will be generated. You will then have 30 seconds to hold the data carrier back into the antenna field before the writing process will be cancelled. HB_GAT-MT010_EN_12 19

20 OPERATION GAT MT OPERATION GAT MT Generally The GAT MT 010 can be operated with two 1.5 V AA batteries (alkali). Use only leak-proof safe batteries! In order to save battery the GAT MT 010 is switched off when not in use. Before a communication can take place, the GAT MT 010 must therefore be switched on. This takes place by pressing the home key for some time. During the start-up the Gantner Logo will be displayed. After that the start screen will appear and all stored locks will be listed, i.e. all doors will be shown which have been configured in GAT Manager and for which data have been copied onto the GAT MT 010. Fig 4.1- Start Screen of the GAT MT 010 Note: Following the term "door" will be used for a lock or terminal respectively, which gets connected to the GAT MT 010. So when you read "downloading data to a door" it means that the lock or terminal respectively, that is connected to the door, will be downloaded. The battery symbol on the bottom left side shows the current state of the batteries. If the GAT MT 010 is operated with a power supply unit, the battery symbol will not be indicated. The symbol shown in the figure 4.1 means that the battery will soon be empty and should be replaced or recharged as soon as possible. 20 HB_GAT-MT010_EN_12

21 OPERATION GAT MT Connection to a Lock/Terminal The GAT MT 010 will be connected to a door (lock or terminal) by means of the supplied download cable. GAT ST 210 Fig Connection to a GAT ST 210 Remove the cover on the front of the GAT ST 210 and plug-in the download cable of the GAT MT 010 into the socket under the cover. GAT ST 22X Fig Connection to a GAT ST 220 and GAT ST 225 HB_GAT-MT010_EN_12 21

22 OPERATION GAT MT 010 Remove the cover that protects the download socket. This cover is located on the side of the GAT ST 220 resp. 225 housing which is mounted on the inside of the door (secured area, housing without button). Plug-in the download cable of the GAT MT 010 into the socket under the cover. TAC Lock Fig Connection to a TAC Plug-in the download cable of the GAT MT 010 into the socket at the bottom side of the TAC housing which is mounted on the inside of the door (secured area, housing without button). 22 HB_GAT-MT010_EN_12

23 OPERATION GAT MT Main Menu By pressing the menu key (green) in the starting window the main menu is displayed: Data exchange with locks/terminals Booking evaluation Configuration of the locks/terminals Configuration of the GAT MT 010 ON / OFF Home Back Scroll OK Fig Main Menu of GAT MT 010 The following functions can be selected with the display keys: DATA: CONFIG: - Download of configurations to doors - Read-out bookings from doors Here the following actions can be performed with the connected door: - Set address - Read-out battery information - Read information - Set time and date - Set mode - Processed GAT ST 2xx (list of the doors that have been loaded already) - Always Open mode - Silent mode BOOKINGS: - Display of all bookings in the GAT MT 010 HB_GAT-MT010_EN_12 23

24 OPERATION GAT MT 010 SYSTEM: Indication and setting of different functions of the GAT MT Display system information - Set date / time - Set display contrast - Set beeper volume - Set display language - Test the plugged-in SD memory card - Reset to factory settings (Attention: stored data will be deleted with this reset. - PC-Config. Mode (configuration via PC) For communication with an offline terminal/lock a programming card must be used to set the terminal/lock into the programming mode! If the programming mode is active the LED at the terminal/lock will blink alternately green and red Menu Function "CONFIG" With this menu function different data of the connected door can be set or read and different functions of the door can be run. By pressing the key "CONFIG" (red) the following list menu will be displayed: CONFIG. 12:21:17.Set Address. Read Battery Data GAT ST 2xx Info Set Date/Time [ ] or [ ] - select desired option 1/ 6 [ ] - run the selected option 8 options are selectable: 24 HB_GAT-MT010_EN_12

25 OPERATION GAT MT 010 Set Address ADDRESS 10:47:55 MANUAL LIST The address of the connected door can be set by entering the address "manually" or by selecting one address from a list. To enter an address manually press the menu key "MANUAL": ADDRESS 12:21:17 Address for GAT ST 2xx: QUIT OK [ ] or [ ] - decrease / increase the number at the cursor position [ [OK] ] or [ ] - move cursor one place to the left / right (green) - writes the address into the door Read Battery Data BATTERY 12:21:17... Info display (displayed for approx. 3 seconds) Ident. Total : Ident./Month : Lifetime : > 30d Batt. Months : Offline Cylinder The first two lines show the number of identifications at the current door and how many identifications took place at the door per month in average. HB_GAT-MT010_EN_12 25

26 OPERATION GAT MT 010 The estimated remaining life time of the battery will be calculated and displayed. Line four shows how many months the battery has been in use. Note: The indicated battery lifetime is an estimation due to the usage frequency of the offline cylinder/lock so far. GAT ST 2xx Info ST 2XX INFO 12:21:17... Info display (displayed for approx. 3 seconds) 100-Offline Cylinder Serialno.: Software : 02.1a Hardware : T :12:57 The type of connected terminal/lock and its serial number, software and hardware version will be displayed. The last line shows the current date and the time of the connected terminal/lock. Set Date/Time With this menu option the time and the date of the connected door can be read and set. DATE/TIME 12:21:17 Time: DD.MM.YY hh:mm:ss :21: QUIT OK [ ] or [ ] - decrease / increase the number at the cursor position [ [OK] ] or [ ] - move cursor one place to the left / right (green) - writes the new date into the door 26 HB_GAT-MT010_EN_12

27 OPERATION GAT MT 010 Change Mode A lock/terminal can work in different modes. You can select the mode with this menu option. MODE 12:21:17. Stand Alone Mode. (Read Only Unique) (Read Write Mode) FID Only Mode QUIT 1/ 7 [ ] or [ ] - select mode [ ] - confirm selection -> marker "O" will be set (" ") Designation Installation Mode Stand Alone Mode FID Only Mode Read Only Unique Read Only Card Read Write Mode Hotel Mode Function At delivery the terminal/lock is in installation mode. By programming a programming and deleting data carrier into the terminal/lock the terminal/lock will change from installation mode to the stand alone mode. User data carriers are configured with programming and deleting data carriers directly at the door. Using the site number of the Gantner time/access segment or identification and authorisation check. Configuration of the doors in GAT Manager and copying of authorisations and configurations from the PC to the doors by means of the GAT MT 010. For authorisation check the unique number of the data carriers will be used. Configuration of the doors in GAT Manager and assignment and change of the authorisations in the GAT Access. For authorisation check the coded GANTNER chip number of the data carriers will be used. Authorisations are stored on the authorisation data carriers of the users. Therefore a write station is necessary (e.g. GAT Writer 5200, GAT Writer 5100, GAT Terminal 2500) Authorisation check performed with data carrier and version number. Additional category classification (e.g. normal guest, cleaning personell, manager) and "privacy function". HB_GAT-MT010_EN_12 27

28 OPERATION GAT MT 010 Processed GAT ST2xx All doors, that have already been loaded, can be listed. PROC. DOORS 12:21:17... Info display (displayed for approx. 3 seconds) 022-Maindoor :10:55 _T_0022.ini [ ] or [ ] - scroll through the list of already processed doors [ ] - exit with this key Always Open Mode With this menu item the Always Open Mode can be activated. ALWAYS OPEN 12:21:17... Indication of current state of the lock Always open Mode:. Activated.. Deactivated QUIT [ ] or [ ] - select desired function [ ] - confirm selection -> marker "O" will be set (" ") If a lock is set to the Always Open Mode it is possible to permanently unlock the door by reading the same data carrier two times within 2 seconds at the lock. The door will then remain unlocked until one more identification is performed with the same data carrier. The Always Open Mode is only available for locks which are working in Stand Alone Mode or FID Only Mode. 28 HB_GAT-MT010_EN_12

29 OPERATION GAT MT 010 Silent Mode SILENT MODE 12:21:17... Indication of current state of the lock Silent Mode:. Activated.. Deactivated QUIT [ ] oder [ ] - select desired function [ ] - confirm selection -> marker "O" will be set (" ") If a lock is set to the Silent Mode the internal beeper will be deactivated. In this case no acoustic signal will be generated in case of an identification at the lock Menu Function "DATA" With this menu function the corresponding configuration data, which has been defined on the PC, can be loaded into the connected door. First the connected lock/terminal must be set into the programming mode. Else the message "GAT ST 2xx is not in program mode" will appear on the display. By pressing the key "DATA" (yellow) the following will be displayed: Connected door will automatically be recognised! DATA 12:21:17 GAT ST 2xx: 100-Offline Cylinder Load Data? NO YES [YES] or [NO] (green) - data will be loaded into the indicated door (here "100-Offline Cylinder") (red) - back to the main menu HB_GAT-MT010_EN_12 29

30 OPERATION GAT MT 010 After loading is completed or if no configuration data for the connected door is stored in the GAT MT 010 it is possible to read-out the bookings that are stored in the door by using the menu item DATA. These bookings will then be deleted in the door. BOOKINGS 12:21:17 No Data for 100-Offline Cylinder available! Read Bookings? NO YES [YES] or [NO] (green) - read bookings (red) - back to the main menu The read bookings can be displayed with the menu function "BOOKINGS" Menu Function "BOOKINGS" A lock and a terminal store internally a booking for every occurred event (operation, error message etc). Stored bookings can be displayed with the menu function "BOOKINGS". SELECT 12:21:17... Info display (displayed for approx. 3 seconds) No Bookings available! [ ] or [ ] - scroll through the list of bookings [ ] - exit with this key Note: In order to display the bookings of a door they must first be transmitted from the door to the GAT MT 010. This can be done with the menu function "DATA" (see Menu Function "DATA"). For each door the max. 500 bookings will be shown, also if more bookings are stored in a doors. 30 HB_GAT-MT010_EN_12

31 OPERATION GAT MT Menu Function "SYSTEM" With this menu function the GAT MT 010 will be configured. By pressing the key "SYSTEM" (green) in the main menu the system menu will appear: SYSTEM 12:21:17.System Info. Date/Time Display Contrast Beeper Volume 1/ 8 [ ] or [ ] - move cursor to the desired option [ ] - select the option with this key In the system menu 8 options are selectable. These will be described below: System Info SYSTEM INFO 10:47:55 INFO VOLTAGE By pressing the "INFO" key (yellow) the serial number, software and hardware version and further information about the GAT MT 010 will be displayed: GAT MT :21:17... Info display (displayed for approx. 3 seconds) Serialnb.: Software : Hardware : CoPr. : 01.1 HB_GAT-MT010_EN_12 31

32 OPERATION GAT MT 010 By pressing the "VOLTAGE" key (blue) information about the actual supply voltages of the GAT MT 010 will be displayed: VOLTAGE 12:21:17... Info display (displayed for approx. 3 seconds) V-External : 11.40V V-Battery : 02.30V V-Internal : 02.97V Power Supply Unit V-External shows the voltage value of the currently external voltage supply (if connected, e.g. a pluggable power supply unit), V-Battery is the current voltage value of the battery and V-Internal is the voltage value that is currently used internal by the GAT MT 010 for processing. Date/Time With this menu option the time and the date of the GAT MT 010 can be set and/or read. Note: Control the date and time periodically! The internal clock of the GAT MT 010 can differ from the real time after long operation.! The clock (time) of the GAT MT 010 will not be adjusted automatically with the PC clock. DATE/TIME 12:21:17 Time: DD.MM.YY hh:mm:ss :21: QUIT OK [ ] or [ ] - decrease / increase the number at the cursor position [ ] or [ ] - move cursor one place to the left / right [OK] (green) - sets the input date and time in the GAT MT HB_GAT-MT010_EN_12

33 OPERATION GAT MT 010 Display Contrast With this menu option you can set the brightness/contrast of the GAT MT 010 display. [ [OK] ] or [ ] - move cursor one place to the left / right to decrease / increase the contrast of the display (green) - Stores the selection Beeper Volume With this menu option you can adjust the volume of the internal beeper of the GAT MT 010. [ [OK] ] or [ ] - move cursor one place to the left / right to decrease / increase the volume of the internal beeper (acoustic signal) (green) - Stores the selection Language With this menu option you can select the display language of the GAT MT 010. LANGUAGE 11:25:12.English. German QUIT HB_GAT-MT010_EN_12 33

34 OPERATION GAT MT 010 [ ] or [ ] - Select Language [ ] - Confirm Selection -> Marker "O" will be set (" ") Test SD-Card With this menu option the memory card in the GAT MT 010 can be tested. SD-CARD 12:21:17 Test SD-Card? NO YES [YES] or [NO] (green) - Start SD-card test (red) - Back to the system menu SD-CARD 12:21:17 No Errors with SD-Card! Indication if the memory card is ok. Else an error message will be displayed. In the case of an error check the memory card (dirty, defect?) and replace it by a new card in case the error cannot be solved. 34 HB_GAT-MT010_EN_12

35 OPERATION GAT MT 010 Factory settings With this menu option the GAT MT 010 can be reset to factory settings.! With a reset to factory settings all data and configuration changes in the GAT MT 010 will be deleted and the GAT MT 010 will be reset to the state at delivery time. FACTORY 12:21:17 Reset device to factory settings? NO YES [YES] (green) - Confirm the reset to factory settings (if desired) or [NO] (red) - Back to the system menu FACTORY 12:21:17 Do you really want to reset the device? NO YES [YES] (green) - If you are really sure to reset to factory settings confirm again or [NO] (red) - Back to the system menu FACTORY 12:21:17 All Data deleted and device set to manufacture settings! Now the GAT MT 010 is again in the state how it was on delivery time. The display language is set to english as default. Please select your desired language with the option "Language" in the menu "SYSTEM" (see page 32). HB_GAT-MT010_EN_12 35

36 OPERATION GAT MT 010 PC-Config. Mode In the PC Configuration Mode the GAT MT 010 can be loaded with data or new software. This menu option will only be used by Gantner Electronic GmbH for internal purposes. If the PC Configuration Mode is active this will be signalised by an arrow moving right/left. [QUIT] (red) -Press this key in order to end the PC Configuration Mode and set the GAT MT 010 back to normal operation. 36 HB_GAT-MT010_EN_12

37 SERVICE AND MAINTENANCE 5. SERVICE AND MAINTENANCE 5.1. Inserting and Changing the Batteries If the batteries in a GAT MT 010 are (nearly) empty, operation is no longer possible. A battery change is necessary. Batteries to be used are 2 x 1.5 V / type AA LR16 (alkaline). The batteries are inserted below the cover at the bottom of the housing. Figure Inserting batteries at the GAT MT 010! Pay attention to the correct polarity and orientation of the batteries when inserting them! A battery change may not last longer than 5 minutes, since otherwise the date and time set in the GAT MT 010 will be lost. In this case time and date must be set again (see section Menu Function "SYSTEM", page 30).! Do not dispose batteries with domestic waste! Dispose batteries in an eco-friendly way, e.g. through a municipal battery collecting box. HB_GAT-MT010_EN_12 37

38 SERVICE AND MAINTENANCE 38 HB_GAT-MT010_EN_12

39 FREQUENTLY ASKED QUESTIONS (FAQ) 6. FREQUENTLY ASKED QUESTIONS (FAQ) Here you can find some important and frequently asked questions concerning the GAT MT 010. If you have any questions about the operation and function of the GAT MT 010 after reading this manual and you also don t find the answer to your question in this section please contact your dealer or the GANTNER Hotline. The GAT MT 010 doesn t recognize the attached lock or terminal. - Make sure that all cables are connected firmly at the correct places. - Make sure that the lock/terminal is set to programming mode. No door names are displayed on the GAT MT Check the directory settings in the software "GAT ST 220 Service" (in the file "ST220Service.ini"). The GAT MT 010 isn t recognised when connected to the PC. - Connect the GAT MT 010 to another USB socket of the PC. - Deactivate the anti virus software. Data aren t displayed anymore at the GAT MT 010 after copying or during operation. - Switch the GAT MT 010 off and then on again. - Make sure that the SD memory card is firmly plugged in. Data cannot be copied to the GAT MT Make sure that the SD memory card is firmly plugged in. - Test the SD memory card for possible errors. HB_GAT-MT010_EN_12 39

40 FREQUENTLY ASKED QUESTIONS (FAQ) 40 HB_GAT-MT010_EN_12

41

42 Specifications: Power Supply: - Pluggable PS Unit: 10 to 15 VDC (pos. pole inside) - Battery: 2 x 1.5 V / type AA - LR16 (Alkaline) Current Consumption: Typ. 100 ma at 12 VDC Max. 130 ma at 12 VDC Power Supply Unit: Prim.: 230 VAC/50 Hz, 22 VA Second.: 12 VDC, max ma Internal Clock: Quartz operated real time clock (RTC) accuracy: < ±0,25 sec. per day at +25 C Program Memory: 2 MByte Flash Main Memory: 16 MByte SDRAM Booking Memory: SD card with 64 MByte Display: Monochrome, graphic capable LC display with background lighting, 128 x 64 pixel Dimensions: Input: - 4 function keys with function description on the display in plain text - 2 cursor keys - 1 "start" key - 1 "OK" key - 1 "back" key Acoustic Signal: Built-in beeper USB Interface: Standard 1.1, plug type B, for connection to a PC RS 232 Interface: DB 15, for connection to GAT ST 210, -220, -225, TAC Material: Plastic Protective System: IP 50 Weight: 260 g Operating Temperature: 0 C up to +60 C Storage Temperature: -25 C up to +70 C Relative Humidity: 0% up to 90% at +25 C (non-condensing) Ordering Information: Designation GAT MT 010 Hand-held terminal for GANTNER offline locks/terminals GAT MT 010 Set GAT MT 010 and GAT Battery Charger SJ GAT MT 010 Cable Cable for communication between GAT MT 010 and doors GAT MT 010 Configuration Cable Cable for communication between GAT MT 010 and PC Part No Valid as of March 28 th 2012 until revocation. Subject to technical modifications! Part No.: Deutschland (Germany) Montafonerstr. 8 Phone: +49 (0) /21 A-6780 Schruns / Austria info-de@gantner.com Phone: +43 (0) Fax: +43 (0) Branch Dubai info@gantner.com Phone : +971 (0) info-me@gantner.com