CX-12. DMX 96 Control channel Dimming Controller. User Manual. Lite-Puter Enterprise Co., Ltd. Website:

Transcription

1 ISO 00 CERTIFIED CX- DMX Control channel Dimming Controller User Manual Enterprise Co., Ltd. Website: CX- [EUM-D]

2 ISO 00 CERTIFIED Introduction CHAPTER. FUNCTION - Feature... - Specification... - Dimension... CHAPTER. SPECIFICATION - The feature function of control panel... - The feature function of rear panel... CHAPTER. POWER SWITCH... CHAPTER. CHANNEL - Brightness of control channel... - Modification of brightness of control channel... - Delete brightness of control channel... CHAPTER. SCENE - SCENE setting... - SCENE SCENE loading... CHAPTER. SEQUENCE - SEQUENCE Editing... - SEQUENCE Modify... - CHASE Loading... - CHASE Fade On/Off Setting... - To stop the CHASE execution... CHAPTER. A/B CROSS FADERS SWITCHING - Save SEQUENCE into A/B CROSS FADER... - Load A/B CROSS FADER... - Pause A/B CROSS FADER... CHAPTER. SET FUNCTION - LCD display / system default setting... - output memory card loading / saving... - Channel patch setting / warm up setting... - Lock / Unlock setting... CX- [EUM-D]

3 ISO 00 CERTIFIED Chapter. CX- Feature & Function - Feature Dual control signal output (.) DMX / (.) channel analog signal output 0 - V control channel, and able to control up to CH CH by patch set of PATCH editing function set of scenes pre-set ( set of scenes able to save on every single page function ) set of chase preset Up to scene step on each chase setting set of individual control stick for scenes change (CROSS FADE) Audio control available output external memory card saving / loading ( option ) - Specification Power supply AC 0-0V, -Hz Digital control signal input / output DMX / Digital control channel channel by PATCH able to control CH CH Digital control connector XLR -pin Audio input Internal microphone MAX 0dB output max. value :AC 0mV Gooseneck connector stand XLR -pin, DC +V 0mA Memory card k* Dimension U standard rack (w) x (h)x(d)mm Weight Kg Warning. Recharge the battery at least hours on before start running. ( power switch turn to ON locate on rear panel ). After first use, the saving data may lost if without battery recharge in days! CX- [EUM-D]

4 SPEED 0 FADE 0 0 PUSH 0 AUDIO FADE A CROSSFADER LOAD CHASER LOAD PAUSE B LOAD P US H LAMP VDC ISO 00 CERTIFIED - Dimension 0 CX- CH DMX DIMMING CONSOLE PUSH CX-DMX CONTROL CHANNELS SCENES MEMORIES DIMMERS OUTPUT PROGRAM SEQUENCES BLANK POWER DIRECTOR PLUS F F CLR 0 F F SET PROG CHASE ENTER SC/CH MASTER CLEAR PAGE 0 CX- [EUM-D]

5 ISO 00 CERTIFIED CHAPTER. CX- SPECIFICATION - Introduction of control panel CX- CH DMX DIMMING CONSOLE SPEED CHASER FADE PUSH LAMP VDC AUDIO CX- CONTROL CHANNELS SCENES MEMORIES DIMMERS OUTPUT PROGRAM SEQUENCES DMX POWER BLANK FADE LOAD PAUSE 0 CROSSFADER A B DIRECTOR PLUS F SET CLR F 0 F ENTER F PROG CHASE SC/CH MASTER LOAD LOAD PAGE CLEAR (.) VR ~ VR VR... VR ~ VR (.) P ~ P hot key... P ~ P function The LED on function key display the channel status ( In channel mode ) function In SCENE mode, for SCENE selection function FLASH function LOAD + P - P hot key for chase function (.) Blank...indication / memo for user (.) SPEED / FADE VR...Adjustment of chase speeding / CROSS FADE speeding (.) FADE save key...cross FADE mode use (.) CHASER VR...chase brightness value adjustment (.) LOAD / PAUSE...Load / Pause auto chase mode use (.) A-CROSSFADER VR...Manual chase A execution mode (.) LOAD...Load / Switch Manual chase A mode use (.)B-CROSSFADER VR... Manual chase B execution mode use CX- [EUM-D]

6 ISO 00 CERTIFIED (.)LOAD...Load / Switch Manual chase B mode use (.)PAGE...PAGE ~PAGE (.)Gooseneck... C+V 0 Ma (.)POWER...power switch (.)BLANK...Pause (.)LCD...LCD display F 0 F F F (.)MASTER VR...Master VR SET (.)CLEAR...output clear (.)F...function key (0.)F...function key (.)F...function key CLR 0 ENTER PROG CHASE SC/CH (.)F...function key (.)SET...function key (.)PROGRAM...function key (.)CHASE...Chase execution (.)SC/CH...scene/channel switch (.)ENTER...enter key (.)0 ~...0 ~ (.)CLR...Clear - REAR PANEL PUSH P U S H ( ) Power switch ( ) fuse ( ) AC 0-0V 0-0 Hz ( ) goosenecks power switch ( ) DMX input ( ) DMX output ( ) memory card ( ) audio input CX- [EUM-D]

7 ISO 00 CERTIFIED CHAPTER Switch Switch on (.) Plug into power source, and turn the power switch on rear panel (.) Turn the power switch on front panel, and check the LCD display status (.) Be sure that the LED on BLANK is off Switch off (.) Turn off the power switch on front panel Battery recharging mode (.) Turn off the power switch on rear panel Battery un-recharge, days duration of save data maintains only Remark The using status will keeping on after power off CX- [EUM-D]

8 ISO 00 CERTIFIED Chapter. CHANNEL - Brightness value STEP- Adjust the MASTER VR to the top (MASTER VR adjust all control channel brightness value) STEP- press SC/CH key, to select the control channel mode (LED show green light on page key) STEP- press PAGE,adjust VR ~ VR,to set CH. 0 ~ brightness value. PAGE START CH0 CHASE FADE ON F/ FADE ON/OFF STEP- press PAGE,adjust VR ~ VR to 0 value, and adjust VR ~ VR to set CH. ~ of brightness value. PAGE START CH CHASE FADE ON F/ FADE ON/OFF STEP- press PAGE,adjust VR ~ VR to 0 value, and adjust VR ~ VR to set CH. ~ of brightness value. PAGE START CH CHASE FADE ON F/ FADE ON/OFF STEP- press PAGE,adjust VR ~ VR to 0 value, and adjust VR ~ VR to set CH. ~ of brightness value. PAGE START CH CHASE FADE ON F/ FADE ON/OFF p.s. when on page function, the VR should be adjust to 0 value, and move the VR key to get the new dimming value CX- [EUM-D]

9 ISO 00 CERTIFIED - Brightness modification STEP- press PAGE (ch-) PAGE START CH0 CHASE FADE ON F/ FADE ON/OFF STEP- adjust VR key to CH0=00 value, and adjust VR key to top CH0=FL, then adjust the VR key to CH0=0 to change the setting. - setting delete adjust VR ~ VR and MASTER VR key to the bottoms 0, and press the CLEAR key on below of MASTER VR key to delete. CX- [EUM-D]

10 ISO 00 CERTIFIED Chapter SCENE - SCENE setting STEP- please refer to the chapter, adjust the dimming value on the control channel. STEP- press PROG F: Scene F: Sequence STEP- press F,and select SCENE mode F: Load F: Clear F: Save STEP- press F,to save the SCENE SELECT [0.. ] SAVE SCENE 0 STEP- press ENTER to confirm the selection ARE YOU SURE?F SAVE SCENE 0 STEP- for further SC --- SC setting, please refer to the setting procedure of above Each PAGE set of SCENE setting available PAGE able to store set of scene CX- [EUM-D]

11 ISO 00 CERTIFIED - SCENE SCENE loading -- use PROG key for SCENE loading STEP- Set all dimming value to 0% (refer to - ) STEP- Adjust MASTER VR key for dimming value STEP- Press PROG, and press F to select the SCENE mode F: Scene F: Sequence STEP- Press F key for SCENE loading F: Load F: Clear F: Save STEP- Press 0 key for number of SCENE loading SELECT [0.. ] LOAD SCENE 0 STEP- Press ENTER to confirmed the scene loading -- use SC/CH key for SCENE loading (FLASH status) PAGE LED SCENE mode PAGE LED CHANNEL mode STEP- Set all dimming value to 0%. (refer to - ) STEP- Adjust the MASTER VR key STEP- Press PAGE CX- [EUM-D]

12 ISO 00 CERTIFIED STEP- Press SC/CH to select the SCENE mode. STEP- Press P for SCENE loading. (Flash status) -- Adjust the VR ~ VR key for SCENEloading STEP- Adjust all control channel dimming value to 0% (refer to -) STEP- Adjust the MASTER VR STEP- Press PAGE STEP- press SC/CH to select SCENE mode (LED light on RED on PAGE key ) STEP- Adjust VR key to for SCENE loading -- or -- SCENE speed loading -- Adjust the VR key for dimming function CX- [EUM-D]

13 ISO 00 CERTIFIED Chapter. SEQUENCE / CHASE "SEQUENCE" meaning set of scene or more of scenes for chase setting Function Provide the " CHASE " & " A/B CROSS FADER " control procedures Data memory up to SEQUENCE of memory data and up to step per SEQUENCE setting - SEQUENCE Editing STEP- Press PROG key F: Scene F: Sequence STEP- Press F key to select Sequence mode F: Load F: Edit F: Save F: Clear STEP- Press F key for Sequence editing F / / / =/ + / - /E SEQU.STEP0=S - - press F back to STEP-0 press F forward press F reward press F to save STEP- Use 0 key to select the SCENE, and press ENTER key to confirmed the selection F / / / =/ + / - /E SEQU.STEP0=S - - STEP- according to the STEP- procedures, to continues the SCENE setting, and press F key to complete the editing, and press ENTER to save SELECT [0...] SAVE SEQUENCE0 CX- [EUM-D]

14 ISO 00 CERTIFIED - SEQUENCE Modification STEP- Press PROG key F: Scene F: Sequence STEP- and press F key to select Sequence mode F: Load F: Edit F: Save F: Clear STEP- press F key, and press 0 key to select Sequence SELECT [ 0.. ] LOADSEQUENCE0 STEP- Press ENTER key to confirmed. F: Load F: Edit F: Save F: Clear STEP- Press F key for Sequence setting - CHASE Loading -- CHASE loading EX to load the st set of chase CHASE number = SEQUENCE number STEP- press CHASE key SELECT 0 CHASE: OFF 0 CX- [EUM-D]

15 ISO 00 CERTIFIED STEP- and press 0 to select the CHASE, and press ENTER to confirm the selection SELECT 0 CHASE: OFF 0 STEP- adjust the CHASER FADER VR to the top.(chase dimming value) STEP- adjust SPEED FADER VR for chase speeding, for audio control, the VR key should move to 0% value. -- Use P-P for chase loading STEP- press LOAD/PAUSE key on below of CHASER FADER VR + P keys together, for st set of chase loading, and press P key for the following chase loading Press LOAD/PAUSE key on below of CHASER FADER VR again to pause the chase function, and press the same keys again to continue Refer to -& ~ - of setting procedures, for further chase setting, up to set of chase setting available. And refer to - for chase loading - CHASE Fade On/Off Setting STEP- adjust the CHASER FADER VR or SPEED FADER VR CHS=FL SPEED=FL OFF Step=0 CHASE FADE ON F/:FADE ON/OFF STEP- press F key, to enter CHASE FADE ON MODE. press F key, to enter CHASE FADE OFF MODE. CHS=FL SPEED=FL OFF Step=0 CHASE FADE ON F/:FADE ON/OFF CHS=FL SPEED=FL OFF Step=0 CHASE FADE OFF F/:FADE ON/OFF CX- [EUM-D]

16 ISO 00 CERTIFIED - to stop the CHASE execution function. Press twice CHASE key to stop function. Adjust the CHASE FADER VR key to the 0% value to stop CX- [EUM-D]

17 ISO 00 CERTIFIED Chapter A/B CROSS FADERS Scene switching "A/B CROSS FADER" set of individual scene control VR In SEQUENCE mode, use A/B CROSSFADER to execute the manual chase function. - To save the SEQUENCE to A / B CROSS FADER EX To load the Sequence to A CROSS FADER STEP- Press LOAD key on below of A CROSS FADER + P keys together to save the current sequence into A CROSS FADER. - To load A / B CROSS FADER data Function press the Load key on below of A/B CROSS FADER The Fader time of A/B CROSS FADER control by SPEED VR key, according to -, to load the saving data from the SEQUENCE by A CROSS FADER. STEP- Adjust SPEED / FADE VR key, and press FADE to confirmed the speed setting, adjust the speed VR key, and press FADE key for modification STEP- Press A CROSS FADER VR to the top, and press LOAD key for loading Function : use A/B CROSS FADER VR According to the setting procedures of above, use the A CROSS FADER VR key for further setting - To pause the A / B CROSS FADER Adjust the A CROSS FADER VR key to the 0% value, and press LOAD key to pause / stop CX- [EUM-D]

18 ISO 00 CERTIFIED Chapter Other function setting - LCD display / default setting -- Power switch of LCD background lighting STEP- Press SET F : Setup F : Patch F : Xio F : Lock STEP- and press F F : Lcd F : Reset system STEP- and press F F : Backlight F : Concen STEP- and press F for brightness of LCD background lighting, press F again to save. F : Backlight F : Concen -- LCD contrast adjustment STEP- refer to STEP-,press F key to adjust the contrast of LCD, and press F again to confirmed. F : Backlight F : Concen CX- [EUM-D]

19 ISO 00 CERTIFIED -- DATA delete STEP- press SET F : Setup F : Patch F : Xio F : Lock STEP- and press F F : Lcd F : Reset system STEP- and press F Reset All Data! Are You Sure? F STEP- and press F to delete all data, the BLANK will be activate, press BLANK key to continue the further setting. * DESK BLACK OUT * CX- V.0 ( C ) - BY LITE PUTER The display will be blinking - External memory card save / load STEP- Press SET F : Setup F : Patch F : Xio F : Lock STEP- and press F F : Read F : Save press F for external memory loading press F for external memory saving CX- [EUM-D]

20 ISO 00 CERTIFIED - Channel patch setting / warm up setting -- Channel patch setting ( up to set of setting ) EX To patch DIMMER0channel to CH0 of CX- STEP- Press SET F : Setup F : Patch F : Xio F : Lock STEP- and press F F:DMXin F:DMXo F:Wrmup STEP- and press F F : Load F : Edit F : Save F : Clear STEP- and press F F/ / / =/ + / - /d DIMMER00<=CH0 press F to DIMMER 00 press F DIM to + press F DIM to - press F DIM address selection STEP- Press F for DIM staring address : : : DIMMER00<= press F DIMMER0 press F DIMMER press F DIMMER STEP- Press F for DIMMER0<=CH-- F/ / / =/ + / - /d DIMMER0<=CH-- CX- [EUM-D]

21 ISO 00 CERTIFIED STEP- key 0, for DIMMER0<=CH0, and press ENTER key to confirmed the setting, the DIMMER0 had PATCH to CX- CH0 F///=/+/-/d DIMMER0<=CH0 STEP- press SET to escape F : Load F : Edit F : Save F : Clear STEP- press F the save ( set of setting available F~F ) STEP- press F to load the patch data from F~F STEP- press F to delete the date, and back to the default setting -- Warm up setting 0~% STEP- press SET F : Setup F : Patch F : Xio F : Lock STEP- and press F F:DMXin F:DMXo F:Wrmup STEP- and press F F : ALLCh F : LoadSc F :Clr. F : to select all channel warm up setting. F : SCENES loading. F : to delete the last step scene setting 0 CX- [EUM-D]

22 ISO 00 CERTIFIED - Lock / unlock function -- password setting STEP- press SET F : Setup F : Patch F : Xio F : Lock STEP- and press F F : Pgm. F : Key F SET, PROG key lock F all function key lock STEP- press F to lock PROG key LOCK PROGRAM: PASSWORD : 0000 Enter digit number, or enter of default password setting STEP- press ENTER key to confirmed the setting -- unlock press SET,and press digit number of password XXXX and press ENTER to unlock CX- [EUM-D]