SPM Series Addendum to IM Series Manual
|
|
- Sabrina Knight
- 5 years ago
- Views:
Transcription
1 SPM Series Addendum to IM Series Manual Solar Powered Water Softening System First Sales, LLC US Highway 33 N Churubusco, IN Phone (260) Fax (260) SPM Addendum docx
2 1
3 Preinstallation Instructions This water softener has been supplied with a copy of the installation and operating instructions for an IM Series water softener. The installation process is performed the same way with the exception of locating the solar panel. Solar Panel Installation: The solar panel should be mounted at a location that is exposed to natural light. The wiring harness will accommodate locating the panel up to 25 away from the water softener control valve. The wiring should then be routed through the back plate of the control valve and connected to the right side of the circuit board. Ensure that the RED wire from the solar panel is connected to the POSITIVE terminal on the circuit board and the WHITE wire from the solar panel is connected to the NEGATIVE terminal on the circuit board. Battery Connection: The battery pack is not connected to the circuit board to conserve battery power during shipping. After solar panel installation, the battery pack should be connected to the circuit board. The connector is located on the bottom of the control valve circuit board. Battery Power: The SPM Series circuit board has a power conservation feature which turns the display off after approximately 20 seconds of inactivity. The display can be reactivated by pressing any button on the panel. The battery back is shipped with a small charge for initial settings and installation. A fully charged battery will require the solar panel to be exposed to natural light for a period of 24 hours or longer, depending on the light intensity. Programming: The solar powered control valve programming is different from the IM Series unit. Please refer to the appropriate programming instructions on the following pages. 2
4 USER Programming The display can be scrolled through the following screens by pressing the NEXT button: Current Time, volume remaining before regeneration, number of days before regeneration override, current flow rate and total water used since last resetting the meter. Display the current time of day is displayed Buttons press and HOLD either the up or down button to set the CURRENT hour (make sure to pay attention to the AM and PM indicator. to advance to the minutes Buttons press and HOLD either the up or down button to set the CURRENT minutes Display VOLUME REMAINING (800 gallons is displayed). This is a calculated value and cannot be manually adjusted 3
5 Display Days to Regeneration Override is displayed (14 days is displayed) Display Current Flow Rate (2.5 gallons per minute is displayed). This is a calculated value based on the current water use and cannot be manually adjusted. Display Total volume since last reset (1,350 gallons is displayed). This totalizing meter can be reset by pressing and HOLDING the DOWN Arrow. to return to the current time of day. 4
6 INSTALLER Programming The installer programming includes setting the incoming water adjusted hardness (in grains per gallon), setting the day override (factory preset for 14 days) and setting the desired time of regeneration (factory preset for 2:00 AM) Buttons press and HOLD the NEXT and UP buttons simultaneously for 5 seconds Display the incoming water adjusted hardness is displayed Buttons press and HOLD either the up or down button to set the adjusted water hardness Display Days of Regeneration Override is displayed (14 days is displayed) Buttons press and HOLD either the up or down button to set the days override 5
7 Display the TIME OF REGENERATION is displayed (factory preset to 2:00 AM) Buttons press and HOLD either the up or down button to set the TIME OF REGENERATION hour (make sure to pay attention to the AM and PM indicator. to advance to the minutes Buttons press and HOLD either the up or down button to set the TIME OF REGENERATION minutes to return to the current time of day 6
8 CYCLE Programming The cycle times and other programming of valves on SPM Series units are LOCKED at the factory. In order to access this programming you must press and release the DOWN, NEXT, REGEN and UP buttons. After reviewing or adjusting the cycles the programming can be relocked by pressing and releasing the same buttons. Buttons press and release in order Display shows whether programming is now locked or unlocked Cycle Times Listed below are typical cycle times and programming for model SPM30 water softeners. Buttons press and HOLD both buttons for 5 seconds Display shows that the unit is programmed as a water softener Display SOFTENER CAPACITY (20,000 grains [20.0 x 1000] capacity is displayed) Display BACKWASH CYCLE (6 minutes cycle duration is displayed) 7
9 Display BRINE DRAW AND SLOW RINSE CYCLE (45 minutes cycle duration is displayed) Display 2 nd BACKWASH CYCLE (4 minutes cycle duration is displayed) Display RAPID RINSE CYCLE (4 minutes cycle duration is displayed) Display SALT SETTING (6 minutes [9 pound] salt setting is displayed) to return display to Home position 8
PROGRAMMING INSTRUCTIONS
PROGRAMMING INSTRUCTIONS SCROLL UP ARROW DOWN ARROW Display Numbers and letters on display in quotation marks are flashing characters. Owners Instructions: The Display should look as follows before you
More informationProgramming. Power Loss. Meter Operation. Regeneration. Service
Power Loss The AccuSoft circuit board is equipped with a Hi-Cap Capacitor and EEPROM memory chip. The capacitor is capable of maintaining the time, for at least two days, in the event of a power outage.
More informationINSTALLATION PROGRAMMING MANUAL
INSTALLATION PROGRAMMING MANUAL PURONICS WATER CONDITIONER Model Terminator MP With SilverShield HYgene Bacteriostatic Protection Manufactured by: Puronics Water Systems, Inc. 5775 Las Positas Road Livermore,
More informationMODEL 6600 Upflow - V2.0
Option Setting Level #1 Programming Chart NOTE: 1. Push Program Button once per display. 2. Option setting may be changed by pushing either the Up or Down Arrow Button. 3. Depending on current valve programming
More informationNavigating the Menus and Keypad
Navigating the Menus and Keypad UP button CANCEL (X) button CHECK MARK or OK button DOWN button UP ARROW button: scrolls up the menu DOWN ARROW button: scrolls down the menu CHECK MARK button: selects
More informationSystem Controller Programming Manual
System Controller Programming Manual for V3030 and V3030-01 Version X105.01 or greater Page 2 System Controller Programming Manual System Controller Programming Manual Page 3 Table of Contents General
More informationUser Guide. Chandler Systems
User Guide Chandler Systems TABLE OF CONTENTS Congratulations We know you ll love your improved water quality, leak detection ability and water conservation benefits of your new DROP Water Management System
More informationNX48 and NX51 NXT Stager Controller
NX48 and NX51 NXT Stager Controller Service Manual TABLE OF CONTENTS NXT STAGER DIMENSIONS...2 SYSTEM SPECIFICATIONS 48ES AND 51ES SERIES...2 SYSTEM DEFINITIONS...3 SYSTEM OPERATION IN SERVICE (SYSTEM
More informationTrap and Skeet. Counter System
Counter System Trap and Skeet Instruction Manual Long Range LLC. 26 Tannery Street Franklin, NH 03235 Introduction Long Range s line of Counter Systems keeps tracks of targets launched and effectively
More informationADVANTAGE DKE QUICK START GUIDE. 2 Make sure you have everything shown here. 3. What s what? All important internal components labeled for you
1 of 6 START HERE 1 Carefully unpack box. 2 Make sure you have everything shown here. 3 Unlock and remove front panel of keypad unit, then using carriage bolts and hex nuts, attach unit to pedestal as
More informationSYSTEMAX 2014 MULTIVALVE ELECTRONIC CONTROLLER WITH DEMAND RECALL
MULTIVALVE ELECTRONIC CONTROLLER WITH DEMAND RECALL Service Manual Table of Contents Item Page Introduction and General Description...3 Front Panel View and Description...3 Modes of Operation...4 Front
More information24/7 Sprinkler Monitor. The Ultimate Rain/Freeze Sensor
24/7 Sprinkler Monitor The Ultimate Rain/Freeze Sensor User s Manual PIONEER SALES, LTD. 5529 Redfield St. Dallas, TX 75235 Phone: (214) 276-0306 Fax: (214) 631-4218 Toll Free: 1-(866) 501-7745 1 Table
More informationAE21 SERIES DISPLAY CONTROL TERMINAL
FN:AE21MAN1.DOC AE21 SERIES DISPLAY CONTROL TERMINAL DESCRIPTION The AE21 Series Display Control Terminal is used for implementing various display functions. It consists of a control terminal, the AE21,
More informationSeries B9 and C9 Electronic Metering Pumps. Instruction Manual. Manual No : 1796 Rev. : D Rev. Date : 11/2015
Series B9 and C9 Electronic Metering Pumps Manual No : 1796 Rev. : D Rev. Date : 11/2015 sales@novatech-usa.com www.novatech-usa.com Tel: (866) 433-6682 Fax: (866) 433-6684 Tel: (281) 359-8538 Fax: (281)
More informationOriginal Greenstar and GS 2 Raven Setup
Original Greenstar and GS 2 Raven Setup Raven Controller Settings needed to communicate with GreenStar System STEP #1: Setting Up Raven Controller Press the DATA MENU button. Press the 1 or 2 Arrow buttons
More information2x2 Switcher for HDMI 1.3
2x2 Switcher for HDMI 1.3 EXT-HDMI1.3-242 User Manual www.gefen.com ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM
More informationDPM Digital DC Power Meter with Data logging capability. User Manual
DPM-3232 Digital DC Power Meter with Data logging capability User Manual Introduction As a digital DC power meter, it measures the real time DC Voltage (5-60V), DC Current (0-60A), Watt, and it also displays
More informationLock Parts. Keys. Key Insertion. Front Unit. Rear Unit. Product Guide. Standard Keypad Bolt Mechanism. Connection Options
Axis locks with a keypad interface are operated by a 4-digit User Code or by an ADA compliant User Key. Manager Keys provide management access and external power. Programming is accomplished via a Programming
More informationInstruction Manual. ROYTRONIC EXCEL Series AD9 Programming Guide Electronic Metering Pumps
Instruction Manual ROYTRONIC EXCEL Series AD9 Programming Guide Electronic Metering Pumps For file reference, please record the following data: Model No: Serial No: Installation Date: Installation Location:
More informationSetup. Programming Instructions. Product Guide
Cue locks with a keypad interface are operated by a -digit User Code or by an ADA compliant User Key. Manager Keys provide management access and external power. Programming is accomplished via a Programming
More informationAEXX SERIES MULTI-FUNCTION CLOCK/TIMERS
FN:XXMFCT1.DOC AEXX SERIES MULTI-FUNCTION CLOCK/TIMERS AEXX SERIES MULTI-FUNCTION CLOCK/TIMERS REV 04/09/09 DESCRIPTION The AEXX Series of Multi-Function Clock/Timers are available with 1, 2.3, 4, 8, or
More informationAMERICAN CHANGER CORP.
AMERICAN CHANGER CORP. 1400 NW 65 TH PLACE Sales: (800) 741-9840 FORT LAUDERDALE, FL 33309 Parts & Service: (888) 741-9840 www.americanchanger.com Fax: (954) 917-5204 AC7076 & AC7076.1 AUDIT PRINTER USER
More informationProduct Guide. Key Button. Pull Handle
Aspire locks with a keypad interface are operated by a 4-7 digit User Code or by an ADA compliant User Key. Manager Keys provide management access and external power. Programming is accomplished via a
More informationMSD IGNITION FOR THE BOMBARDIER DS 650 QUAD PN /PN 4205
MSD IGNITION FOR THE BOMBARDIER DS 650 QUAD PN 05-08-4205/PN 4205 Parts Included: 1 - PN 05-08-4205/PN 4205 Ignition WARNING: During installation, disconnect the battery cables. When Disconnecting, always
More information7500-S Greensand Filter Installation Guide
Clean Water Made Easy www.cleanwaterstore.com 7500-S Greensand Filter Installation Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance your system
More informationProduct Guide. Key Button. Pull Handle
Aspire locks with a keypad interface are operated by a 4-7 digit User Code or by an ADA compliant User Key. Manager Keys provide management access and external power. Programming is accomplished via a
More informationMaster-Touch INSTRUCTION MANUAL. Series 9000MP Multipoint System Series 9600MP System Control Panel Thermal Gas Mass Flowmeters. version 7.
Master-Touch version 7.x firmware Series 9000MP Multipoint System Series 9600MP System Control Panel Thermal Gas Mass Flowmeters INSTRUCTION MANUAL 80201501 Addendum Rev. C www.epiflow.com Eldridge Products,
More information4x2 Switcher for HDMI 1.3
4x2 Switcher for HDMI 1.3 EXT-HDMI1.3-442 User Manual www.gefen.com ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM
More informationDigital Lock User Guide
Digital Lock User Guide KEYPAD Keypad digital locks are operated by a 4-7 digit User Code. Manager Keys provide management access and external power. Programming is accomplished via a Programming Key unique
More informationSeven Channel Remote Control
Seven Channel Remote Control Page 1 Versa7 Kit Contents The Versa7 is designed to remotely control up to seven devices, or functions. All seven functions can be controlled with the supplied four button
More informationMETERING/DISPLAY MANUAL
METERING/DISPLAY MANUAL 175W - 750W SINGLE PHASE Series LV EMERGENCY LIGHTING CENTRAL INVERTER Myers Power Products, Inc. 44 South Commerce Way, Bethlehem, PA 18017 1-800-526-5088 (610) 868-3500 Fax: (610)
More informationQUICK START. Installation & Programming Guide
QUICK START Installation & Programming Guide PRECAUTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS. CAUTION - RISK OF ELECTRICAL SHOCK. To prevent electrical shock, turn off power at the circuit breaker
More informationINSTALLATION INSTRUCTIONS 5" SINGLE CHANNEL ULTIMATE TACH
Instr. No. 2650-887C INSTALLATION INSTRUCTIONS 5" SINGLE CHANNEL ULTIMATE TACH MODEL 6871, 6872, 6873, 6874, 6875, 6877 IMPORTANT WEAR SAFETY GLASSES 5 4 6 COPYRIGHT PATENT PENDING 3 7 8 PLAYBACK 9 2 0
More informationFLECK 5810 & 5812 XTR2 WATER SOFTENER OR FILTER CONTROL VALVE SERVICE MANUAL
FLECK 5810 & 5812 XTR2 WATER SOFTENER OR FILTER CONTROL VALVE SERVICE MANUAL 5810 5812 waterpurification.pentair.com TABLE OF CONTENTS OPERATING PARAMETERS... 2 INSTALLATION... 3 START-UP INSTRUCTIONS/FLUSHING
More informationOPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS (gray model# CEI-4710) (blue model# CEI-4700) Please read this manual! This manual contains setup information necessary to achieve proper performance from your Pocket Pro II. 815.874.8001
More informationUser/Installation Manual
User/Installation Manual ADVANTAGE DKLP MODEL 19-100(i) Your Partner in Access Control www.americanaccess.com AAS 2Year Limited Warranty What item(s) this warranty applies to: American Access Systems DKLP
More informationRatio Feeder Series J+ Advanced Pumper Controller
UNPACKING Figure 1 J Plus Controller Please open and inspect your package upon receipt. Your package was packed with great care and all the necessary packing materials to arrive to you undamaged. If you
More informationTwo Wire Back Flush Controller Installation and Operating Instructions Hit Products Corporation Lindsay, CA.
Two Wire Back Flush Controller Installation and Operating Instructions Manufactured by: Hit Products Corporation Lindsay, CA. USA TABLE OF CONTENTS Specifi cations... 4 Wiring Connection... 5 Getting
More informationAEXX-273 SERIES WIRELESS CONTROLLED PACE CLOCKS
FN:273MAN1.DOC AEXX-273 SERIES WIRELESS CONTROLLED PACE CLOCKS DESCRIPTION AEXX-273 Series Wireless Controlled Pace Clocks are available in with 1", 2.3", 4", 8", or 12" high digits, visible from 5 feet
More informationEA-R03 Wireless Keypad Controller Kit Operating Instructions
Package Contents Normal Use EA-R02-202 Receiver EA-R03-103 Wireless Keypad Transmitter Keypad Mounting Packet Power/Auxiliary Connector Wire Harness Lock/Unlock Relay Connector Wire Harness User Instructions
More informationTable of Contents. Owner Dashboard 5
Community Solar Portal Community Solar, also known as Aggregated Net Metering, allows customers to use the output of offsite generation to reduce billed usage at their homes or businesses. Participating
More informationNEBULA X USER MANUAL. Redefining Tradition. Read carefully before using the device and save these instructions.
NEBULA X Redefining Tradition USER MANUAL Read carefully before using the device and save these instructions. USER MANUAL Table of Contents...Page 1. An Introduction to Your New Nebula.... 2 2. Packaging
More informationSeries 3000 User Manual and Product Features
Series 3000 User Manual and Product Features PN: OXA3501-890000 Revision 1.0 Technical Specifications 1.1 Model Number Description 1. Meter Series S3 Series 3000 meter Figure 1: Series 3000 model number
More informationPick up the handset from the base. You should hear a dial tone and the display on the base should say TALK. If display says
WALL Uniden XDECT 1 of 6 1 Unpack the telephone Remove all components from the box and remove the protective plastic. Remove the printed tag from underneath the base. Basic set-up guide 2 Connect the handset
More informationSecured Series: Hub Plus Kit Single Door Controller Package Installation Manual
Secured Series: Hub Plus Kit Single Door Controller Package Installation Manual This package is designed to simplify the connections to our Secured Series Hub Plus Controller. This will translate into
More informationOwner s Manual. Model 6672A. 600 Series ipad Conversion Kit 6672A-16 1/17
Owner s Manual Model 6672A 600 Series ipad Conversion Kit 6672A-16 1/17 Harvest Tec 6672A Table of Contents Page Introduction 3 Installation of Bluetooth Receiver 3-6 Large Square Baler Power Cable and
More informationWalkLAB HC Professional Conductivity-TDS-Salinity Meter. Operations Manual 15,0,11,4,1,14,5,10,13,2,9,6,3,12,7,8
15,0,11,4,1,14,5,10,13,2,9,6,3,12,7,8 15,0,15,0,1,14,1,14,13,2,13,2,3,12,3,12,11,4,11,4,5,10,5,10,9,6,9,6,7,8,7,8 WalkLAB Professional Conductivity-TDS-Salinity Meter HC 9021 Operations Manual 0 INTRODUCTION
More informationGSM AD05 Slave GSM Auto Dialer- Instruction Manual
GSM AD05 Slave GSM Auto Dialer- Instruction Manual Please read these instructions before you start the installation Features LCD display Programmable 9 x 32 digit phone numbers for each trigger. 10 second
More informationAUTOMATE Paradigm Cut-In Wall Switches
AUTOMATE Paradigm Cut-In Wall Switches 433 MHz AUTOMATE Paradigm wall switches feature a contemporary design and a wirefree deployment, making them retrofit ready for any location. Available in single,
More informationSTC7D. Digital Time Clock for TRC500 & TRC800. Installation, Operation, and Maintenance Manual
STC7D Digital Time Clock for TRC500 & TRC800 Installation, Operation, and Maintenance Manual READ AND SAVE THESE INSTRUCTIONS The purpose of this manual is to aid in the proper installation and operation
More informationOperation Guide CT32 ENGLISH
Operation Guide CT32 The CT32 communicating thermostat operates via a high-quality, easy-to-use touch screen. To set or adjust your CT32, simply touch your finger firmly to the screen. The screen will
More informationINSTALLATION AND OPERATING INSTRUCTIONS DSST SYSTEM
INSTALLATION AND OPERATING INSTRUCTIONS DSST SYSTEM PROPORTIONAL and NON-PROPORTIONAL TOGGLE SWITCH RADIO REMOTE CONTROL SYSTEM MODEL FHSTP/DSSTP SERIES FHST/DSST SYSTEM DESCRIPTION The DSST Wireless Control
More informationAdjustable Timing Control PN 8680
Adjustable Timing Control PN 8680 IMPORTANT: Read the instructions before attempting installation. Parts Included: 1 - Timing Control, PN 8680 1 - Control Knob 1-3/8" Bushing 1-2-Pin Weathertight Connector
More informationAVOUTLET.com. 433 MHz
AUTOMATE Paradigm Cut-In Wall Switches INSTR-MTRF-SW-1C.2C.15LED V1.1 MAR 2017 433 MHz AUTOMATE Paradigm wall switches feature a contemporary design and a wirefree deployment, making them retrofit ready
More informationManual. NanoTron Dual Timer. Installation Maintenance Repair Manual
Manual NanoTron Dual Timer Installation Maintenance Repair Manual Advantage Controls P.O. Box 1472 Muskogee, OK 74402 Phone: 800-743-7431 Fax: 888-686-6212 www.advantagecontrols.com email: support@advantagecontrols.com
More informationDexter Washer Programing. Part # 8533-***-*** 03/14
Dexter Washer Programing 3 PROGRAMMING INSTRUCTIONS: The washer control can be programmed to prompt the user for alternate vend prices, change washer cycle times, temperatures and many other options. This
More informationDESSMANN - FINGERPRINT LOCK
DESSMANN - FINGERPRINT LOCK User Guide V500 & S510 Version 1.5 1 Contents 1 Introduction 3 1.1 Packing List............................................. 3 1.2 Technical Data...........................................
More informationColor-Sensing Connected Components Building Block. Quick Start
Color-Sensing Connected Components Building Block Quick Start Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety
More informationDESSMANN - FINGERPRINT LOCK
DESSMANN - FINGERPRINT LOCK User Guide K6 - K8 Version 1.5 1 Contents 1 Introduction 3 1.1 Packing List............................................. 3 1.2 Technical Data...........................................
More informationCF3000 Dealer Diagnostic Tool Instruction Manual
CF3000 Dealer Diagnostic Tool Instruction Manual Table of Contents: About the CF3000......3 Important Precautions......4 Components....5 Charging the CF3000......7 Licensing the CF3000.......8 Updating
More informationINSTRUCTION MANUAL FN-8118 SCAN HERE
FENIEX // 2018 // INSTRUCTION MANUAL Is this the latest version? SCAN HERE FN-8118 INSTRUCTION MANUAL Feniex Product Copyrights This price List and the mentioned Feniex products include or describe copyrighted
More informationDOUG FLEENOR DESIGN. Model: NODE Ethernet to DMX512 Gateway OWNER'S MANUAL
DOUG FLEENOR DESIGN (805) 481-9599 Model: NODE4 802.3 Ethernet to DMX512 Gateway OWNER'S MANUAL Doug Fleenor Design 396 Corbett Canyon Road Arroyo Grande, CA 93420 (805) 481-9599 Revision 2.0 January 2013
More informationINSTALLATION & USER MANUAL
INSTALLATION & USER MANUAL MODELS EVMS & GSVMS with Rain Sensor 00--0 Fax: 0-- csm@wascoproducts.com www.wascoskylights.com Eastern Facility: Spencer Drive, Unit A, Wells, ME 000 Western Facility: Echo
More informationTITAN S8. Portable Data Acquisition Logger. Product User Guide
TITAN S8 Portable Data Acquisition Logger Product User Guide Table of Contents 2 General Features... 3 Device Overview... 3 External Features... 3 Device Orientation... 4 Device Inputs... 5 Sensor Types
More informationMODEL 9386 MULTI-SPORT TIMER
MODEL 9386 MULTI-SPORT TIMER Instruction Manual Address: 34 Main Street, Whitesboro, NY 13492 Phone: 315-736-3967 Toll Free: 800-383-6060 Fax: 315-736-4058 SCOREBOARDS TIMERS MESSAGE SIGNS VIDEO DISPLAYS
More informationTile Plow Installation Gold Digger
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Tile Plow Kit Soil Max System 4100470 1 Hex head cap screw - M10 x 75mm 2002007-10075
More informationFLECK 5810 & 5812 XTR2 WATER SOFTENER OR FILTER CONTROL VALVE SERVICE MANUAL
FLECK 5810 & 5812 XTR2 WATER SOFTENER OR FILTER CONTROL VALVE SERVICE MANUAL 5810 5812 waterpurification.pentair.com TABLE OF CONTENTS OPERATING PARAMETERS... 2 INSTALLATION... 3 TOUCHSCREEN CONTROL FEATURES...
More informationElecsys ISM-4. Remote Monitoring System
Elecsys ISM-4 Remote Monitoring System Installation and Product Specification Manual ISM4-L1 (Modbus) 81-0049-03 Rev B Page 1 of 15 Elecsys ISM-4 Contents 1 Getting Started... 3 1.1 Applications... 3 1.2
More informationModel: Available in : Sapphire Black and Glacier White
Model: Available in : Sapphire Black and Glacier White 1 Table of Contents Product Image 1 Locking/Unlocking the SmartStat 20 Table of Contents 2 Standby/Away Mode 21 What is a Programmable Room Thermostat?
More informationXEA217 Frequently asked questions.
XEA217 Frequently asked questions. How do I prepare my XEA217 for set-up? Take the XEA217 out of its box, remove the packing materials. Place the XEA217 on a flat stable surface, close to a power outlet.
More informationLAKEWOOD INSTRUMENTS REMOTE WINDOWS SOFTWARE
LAKEWOOD INSTRUMENTS REMOTE WINDOWS SOFTWARE USER S MANUAL Lakewood Instruments 7838 North Faulkner Road, Milwaukee, WI 53224 USA Phone (800) 228-0839 Fax (414) 355-3508 http://www.lakewoodinstruments.com
More information*520886* IntelliTouch Pool & Spa Control System MobileTouch Wireless Controller. User s and Installation Guide. P/N Rev A
pool/spa control system IntelliTouch Pool & Spa Control System MobileTouch Wireless Controller User s and Installation Guide P/N 520886 - Rev A *520886* i MobileTouch Wireless Controller kit contents The
More information7 Day Digital Programmer 2 Channel Surface Mount
7 Day Digital Programmer 2 Channel Surface Mount Model: TRT036N Installation & Operating Instructions 1. General Information These instructions should be read carefully and retained for further reference
More informationOperator s Manual. Morbark Integrated Control System Woodhog Series Model 2600
Operator s Manual Morbark Integrated Control System Woodhog Series Model 2600 Contents Introduction 4 Parts Identification 6 Display Module Display Pages 9 Main Page 11 Engine Information Page 12 Hydraulic
More informationMSD Enhancer Ignition for the Honda TRX400EX PN /PN 4203
MSD Enhancer Ignition for the Honda TRX400EX PN 05-00-4203/PN 4203 Parts Included: 1 - Programmable Enhancer Ignition 1 - Y-Splice 1 - MSD Coil Assembly 1 - Black Ground Wire 1 - Ignition Mounting Brackets
More informationAg Leader Technology. DirectCommand Installation Hardi 20-pin Interface Kit (Sprayer Chassis Mount)
Part Name / Description Part Number Quantity DirectCommand Hardi Sprayer Kit 4100882 1 Dust Receptacle 8-pin 2002975-8C 1 Installation Instructions 2006335 1 Quick Reference Card- Liquid Application 2002831-38
More informationS-500 Snow Machine User Manual English
S-500 Snow Machine User Manual English 2016 Antari Lighting and Effects Ltd. 2 User Manual Safety Information Please read the following safety information carefully before operating the machine. Information
More informationDPM-3221 Digital DC Power Meter with data logging capability.
Introduction DPM-3221 Digital DC Power Meter with data logging capability. User Manual As a digital DC power meter, it measures the real time DC Voltage (5-60V), DC Current (0-200 A with the correct shunt),
More informationSCHMIDT MODEL G4 TAXIMETER PROGRAMMING MODULE OPERATORS INSTRUCTIONS. Version 5, 1 st February 2011
SCHMIDT MODEL G4 TAXIMETER PROGRAMMING MODULE OPERATORS INSTRUCTIONS. Version 5, 1 st February 2011 The Model G4 Programming Module The Schmidt Model G4 Taximeter Programming Module is a multifunction
More informationNIDEC-SHIMPO INSTRUMENTS
Series FGE-XY Force Gauges Operation Manual NIDEC-SHIMPO INSTRUMENTS Do not operate or store instrument in the following locations: Explosive areas, near water, oil, dust or chemicals; areas where the
More informationSeries FGE-XY Force Gauges Operation Manual
Series FGE-XY Force Gauges Operation Manual Do not operate or store instrument in the following locations: Explosive areas, near water, oil, dust or chemicals; areas where the temperatures can exceed 104
More informationSelf Sustaining Arduino
Description This document is a tutorial for creating a self sustaining Arduino board, by harnessing solar energy. It would be incorporated with a rechargeable 9V battery. What makes this unique is that
More informationT2 863 Transmitter, R2 863 Receiver 863 MHz Portable FM Listening System - Europe
T2 863 Transmitter, R2 863 Receiver 863 MHz Portable FM Listening System - Europe QUICK SETUP GUIDE MAN 182E Operating Instructions 1. Open the battery compartment by sliding the compartment door away
More informationETHERNET IRRIGATION CONTROLLER. Irrigation Caddy Model: ICEthS1. User Manual and Installation Instructions
ETHERNET IRRIGATION CONTROLLER Irrigation Caddy Model: ICEthS1 User Manual and Installation Instructions I R R I G A T I O N C A D D Y M O D E L : I C E T H S 1 User Manual and Installation Instructions
More information212iL Rev. 1.1
212iL 1 International Electronics, Inc. 427 Turnpike Street Canton, Massachusetts 02021 212iL (illuminated Luxury) Keypad Single Unit Keypad- Control Installation Manual Features: 120 User Capability Illuminated
More informationTile Plow Installation O Connell
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Tile Plow Kit O Connell System 4100471 1 Hex head cap screw 3/8-16 x 3 2002003-38300
More informationRenewable Energy. Getting Started With the LEGO Energy Meter
Renewable Energy Getting Started With the LEGO Energy Meter de LEGO Group. 2010 The LEGO Group. 1 Table of Contents 1. Energy Meter Overview... 3 2. Attaching the Energy Storage... 3 3. Charging and discharging
More information1411 S. Roselle Rd. Schaumburg, IL Phone (847) Fax (847)
The Touch Screen Control System consists of two components, the Touch Screen (TS) and the Switch Panel Module(SPM). The PowerQuest system can control the switching of 8 circuits. 6 circuits are predefined
More informationWATCHMINDER3 TO START A NEW WATCH
WATCHMINDER3 1 Mode/Set 2 Scroll Up-Push and hold down to scroll up quickly 4 Light-Stays on for 5 seconds Negative Pole for Recharging 3 Scroll Down-Push and hold down to scroll down quickly TO START
More informationSMART SHOT CONTROLLER FLUID USERS GUIDE
SMART SHOT CONTROLLER FLUID USERS GUIDE Pg. 2 SMART SHOT CONTROLLER FEATURES 3 SMART SHOT CONTROLLER FEATURES 3 SMART SHOT CONTROLLER CONFIGURATIONS 4 FLOAT/SENSOR WIRING 5 TOP AND BOTTOM FLOAT/SENSOR
More informationCOMPLETE INSTALLATION & PROGRAMMING GUIDE
COMPLETE INSTALLATION & PROGRAMMING GUIDE INSTALLATION & PROGRAMMING GUIDE Required Parts for installation - EVOALL 'Standalone" remote start system - MYCAR Telematics kit - HRN-MCAR-01 Main harness (included)
More informationSERVICE MANUAL MODEL SSW-521-D2-ADA
SSW-521-D2-ADA-SPK1.07UNVLr3-ADA-ISSUE4.0 SERVICE MANUAL FOR MODEL SSW-521-D2-ADA STAINLESS STEEL HANDS FREE WALL TELEPHONE WITH OPTIONAL ADA FEATURE AND OPTIONAL SECOND-NUMBER AUTO-DIAL FEATURE EQUIPPED
More informationModel IMP-22G2,H Low Cost Slave Clock Impulser Converts your slave clock to a working timepiece without modifying its original mechanism.
Model IMP-22G2,H Low Cost Slave Clock Impulser Converts your slave clock to a working timepiece without modifying its original mechanism. The PIEXX IMP-22G2, H allows you to put your slave clock back into
More informationTABLE OF CONTENTS TABLE OF CONTENTS... 1 MANUAL REVISION HISTORY... 2 IMPORTANT SAFETY NOTICE...
TABLE OF CONTENTS TABLE OF CONTENTS... 1 MANUAL REVISION HISTORY... 2 IMPORTANT SAFETY NOTICE... 3 1.0 General Information... 5 1.1 System Components... 5 1.2 Specifications... 5 1.2.1 Torque Ranges...
More informationAUTOMATION. Operator s Manual. PG5 Digital Pressure Gauge
AUTOMATION P R O D U C T S GROUP, INC. Operator s Manual PG5 Digital Pressure Gauge DOC. 9003264 Rev. A1 3/10 Tel: 1/888/525-7300 Fax: 1/435/753-7490 www.apgsensors.com E-mail: sales@apgsensors.com PG5
More informationProgramming and Installation Manual
Flow Meters 100 East Felix St. South, Suite 190 Fort Worth, Texas 76115 800.235.1638 Fax: 817.921.52822 www.blancett.com Specifications Power Supply: - 1 D size 1.5 Volt Alkaline Battery - 4-20mA Loop
More informationLock Orientation - Views. Keys. Key Insertion. Product Guide. Keypad Key Managed. Horizontal - Handle on Right. Vertical
Sola locks with a keypad interface are operated by a -digit User Code or by an ADA compliant User Key. Manager Keys provide management access and external power. Programming is accomplished via a Programming
More informationOperation Guide CT101
Operation Guide CT101 PG 1 The CT101 communicating Z-Wave thermostat operates via a high-quality, easy-to-use touch screen. To set or adjust your CT101, simply touch your finger firmly to the screen. The
More informationRobot Light V2. User Manual
Robot Light V2 User Manual 2 Please read over this manual before operating the light. Introduction Unpacking: Thank you for purchasing the Robot Light V2. Every Robot Light V2 has been thoroughly tested
More informationProgramming/Troubleshooting Instructions
Programming/Troubleshooting Instructions E5400LN Cylindrical Series & E890 Exit Device Trim Series E8850FL Mortise Series Operational Modes Secure Normal locked state. Any assigned user code can gain access.
More information