Quick Installation Guide

Transcription

1 Quick Installation Guide 4G Mobile Router & Access Point 150 Mbps Wireless-N w/ USB port HN-MRN1U Version 1.00 (June 12)

2 Package Contents HN-MRN1U with battery USB Power Cable USB/RJ-45 LAN Cable Quick Installation Guide Minimum System Requirements 3G/4G USB MODEM with active subscription 3G/4G USB MODEM is compatible with HN-MRN1U iphone 3G/3Gs or below iphone 30pin connector/usb Cable PC with Ethernet Port and/or Wireless Wireless Adapter for non Wireless-enabled PCs 1

3 4G Mobile Router & Access Point Hardware Description Adjustable USB connector, when not in use, retracts into the 7. WAN/LAN casing of the device, leaving a perfectly flush, rounded (RJ45 Converter Cable required) surface. 8. DC Power Mini USB Slot 2. Power Light 9. Power Switch: Blue : On ON : Turn On 3. Battery Light OFF : Turn Off Blue : Full charge C : Turn to charge Purple : Charging in progress smartphone Red : Battery is weak, need to charge in time No Light : Battery is out of power, or no battery inserted 10. Reset / WPS WPS : 1 Sec pressed 4. WiFi Light Reset : 5 Sec pressed Blue : Wi-Fi is on and no insert WAN/LAN cable Purple : Wi-Fi is on and insert WAN/LAN cable 11. Battery Compartment Red : Wi-Fi is off and insert WAN/LAN cable 5. Signal Light Blue : Signal is strong Purple : Signal is general Red : Signal is weak 6. Network Mode Light 3G Card Access: Red - Always on : Wireless network card incompatible - Flashing 1 time/sec : Network Registering 4 Purple - Always on : registered on 2G network and dialed - Flashing 1time/Sec : registered on 2G network and dialing - Flashing 1time/3 Sec : registered on 2G network, not dialing Blue - Always on : registered on 3G network and dialed - Flashing 1time/Sec : registered on 3G network and dialing - Flashing 1time/3 Sec : registered on 3G network,not dialing WAN Access: No light : Network cable is not plugged or disconnected Blue - Always on : DHCP/ADSL connected - Flashing 1time/Sec : DHCP/ADSL connecting 2

4 How to charge your HN-MRN1U? You should charge your HN-MRN1U when its battery Led is Red or no light. You can charge it via: AC Adapter with USB port USB Power Cable connected to your PC In both cases, make sure the adapter/power cable USB connector is plugged in DC Power Mini USB Slot. Modes of Operation This device can operate in different modes 3G/4G Hotspot iphone Network Tethering Mini AP 3G/4G Hotspot Mode Note: This mode is Default Mode for all users who need to simply and fast connect to 3G/4G Internet wirelessly. Why to use this mode? 1. You have a 3G/4G USB MODEM. You need to share it wirelessly with your friends. Hardware Installation 1. Make sure the battery is installed. 2. Make sure the 3G/4G USB MODEM is compatible with HN-MRN1U. 3. Make sure the SIM card is inserted into your USB MODEM and that you have active subscription. 4. Connect your 3G/4G USB MODEM into the USB port at the top of the Device. 5. Switch the device ON by sliding the power switch to ON position. 3

5 6. Wait until: PWR Led is ON (Stable/Blue) Battery Led is ON (not off: out of power or red: weak) WiFi Led is ON (Stable/Blue) Signal Led is ON (not red: weak signal) Network Mode Led is ON (not red: not registered) 7. Wait until: 3G/4G USB MODEM Led is active similar to same activity when plugged into PC, connected to Network and working. 8. To connect your PC to LogN HN-MRN1U, make sure your PC wireless is ON, search for LogN_xxxx in your PC wireless list, connect. 9. Make sure that your PC Operating System (ex. Windows) tells you are connected to LogN HN-MRN1U wirelessly. Congratulations, you are connected to Internet! Hardware Configuration 10. Open your Internet Browser (ex. Internet Explorer), Type any address It will direct you to the LogN HN-MRN1U Configuration page. 4

6 11. Type admin for user name and password for password when prompted to type them. Changing Wireless Name 12. Select Wireless >> Basic 13. Here you will change the name of your Wireless Network. Type the Wireless Name (SSID) you want your Wireless Network appear with. If you leave it, it will default to LogN_xxxx. Press Apply. Note: Your connection will normally cut for the name of wireless was changed. Search your PC wireless list for the new name, Connect. 5

7 Securing Wireless Connection 14. Select Wireless >> Security. 15. Select from Security Mode drop menu WPA-PSK. 16. Select WPA Algorithms as AES. 17. Type the Password for your Wireless Connection in Pass Phrase, Make it difficult for intruders to guess. The password can be of any character but it should not be less than 8 characters. Press Apply. Note: Your connection will normally cut for a wireless password was introduced. Search your PC wireless list for your wireless name, Type the password when prompted to type it and Connect. 6

8 iphone Network Tethering Mode Why to use this mode? 1. You have a 3G/3Gs or below versions of iphone. You need to share its 3G/4G Connection wirelessly with your friends. Note: This mode has no meaning with iphone4. They can operate in Wireless hotspot mode. Hardware Installation 1. Make sure the battery is installed. 2. Connect the iphone with 30pin connector. 3. Connect your iphone 30Pin connector/usb cable into the USB port at the top of the Device 4. Turn on iphone's Personal Hotspot from Settings>>General>>Personal Hotspots (please select to turn on USB only when prompted in the iphone screen) 5. Switch the device ON by sliding the power switch to ON position. 6. Wait until: PWR Led is ON (Stable/Blue) Battery Led is ON (not off: out of power or red: weak) WiFi Led is ON (Stable/Blue) Signal Led is ON (not red: weak signal) Network Mode Led is ON (not red: not registered) 7. To connect your PC to LogN HN-MRN1U, make sure your PC wireless is ON, search for LogN_xxxx in your PC wireless list, connect. 8. Make sure that your PC Operating System (ex. Windows) tells you are connected to LogN HN-MRN1U wirelessly. Congratulations, you are connected to Internet! 7

9 Hardware Configuration Same like 3G/4G Hotspot Mode Mini AP Mode Why to use this mode? 1. You have Internet cable in home coming from neighborhood but you need Wireless Connection in your home. 2. You have ADSL MODEM with no Wireless Connection. You need wireless connection in your home. 3. You have ADSL MODEM with Wireless Connection in home but it does not cover the entire home. You need another Wireless Access Point to cover uncovered areas. You will link both devices with a cable. Hardware Installation 1. Make sure the battery is installed. 2. If you have a cable coming from neighborhood, connect it to the RJ-45 port of USB/RJ-45 LAN Cable. 3. Connect USB port of USB/RJ-45 LAN Cable to the USB port of the HN-MRN1U 4. Switch on your LogN HN-MRN1U by sliding the power switch to ON position. 5. Wait until: PWR Led is ON (Stable/Blue) Battery Led is ON (not off: out of power or red: weak) WiFi Led is ON (Stable/Blue) Network Mode Led is ON (Stable/Blue) 6. To connect your PC to LogN HN-MRN1U, make sure your PC wireless is ON, search for LogN in your PC wireless list, connect. 8

10 7. Make sure that your PC Operating System (ex. Windows) tells you are connected to LogN HN-APN2 wirelessly. 8. Connect to LogN HN-MRN1U page similar to what learnt in 3G/4G Hotspot Mode. 9. Select Internet >> WAN. 10. Open drop menu of WAN Connection Type and select DHCP, press Apply 11. Connect to LogN HN-MRN1U page similar to what learnt in 3G/4G Hotspot Mode. 12. Select Internet >> Ports Set 9

11 13. Select Set Interface as WAN and press Apply. Congratulations, you are connected to Internet! Power Bank This Device can be used as a Power Bank to charge your Mobile Phones and any USB chargeable devices via its top USB port. 1. Make sure that HN-MRN1U is battery full. 2. Slide the power switch of HN-MRN1U to off position. 3. Simply connect your Mobile Phone USB charging cable to the top USB port of HN-MRN1U. 4. Slide the power switch of HN-MRN1U to C position to start charging your Mobile Phone. Congratulations, you are charging your Mobile Phone! 9

12 Hotline (Egypt): International: Website: Operation Hours: 7days/week 9:00am 9:00 pm (GMT+2)