Service Tool ECA-ST 101

Transcription

1 User Guide *087R9746* *vijen102* Service Tool ECA-ST 101 Software for operation of the ECL Apex 10 controller VI.JE.N1.02 Danfoss 11/2004 DH-SMT VI.JE.N1.02 Danfoss 11/2004 DH-SMT

2 ECA-ST 101A/B VI.JE.N1.02 Danfoss 11/2004 DH-SMT VI.JE.N1.02 Danfoss 11/2004 DH-SMT

3 Table of Contents Introduction...2 Prior to installation...3 How to install the program...4 How to start the program...5 Navigation...6 Authorization...8 DH-SMT VI.JE.N1.02 Danfoss 11/2004 1

4 ECA-ST 101A Introduction The service tool ECA-ST 101 is used for the configuration and setting of your district heating controller ECL Apex 10. In this user guide you are given a brief explanation of the possibilities offered by the service tool ECA-ST 101. The aim is that you become familiar with displays and navigation principles on a general level. The service tool is the browser which informs you about parameters, settings, status and alarms. Technical documentation for the ECL Apex 10, service tool and extension modules is available on the enclosed CD or can be downloaded from the Danfoss Internet site: Prior to installation Min PC requirements Intel Pentium or equivalent processor Windows 98, Windows 2000, Windows NT, Windows Me or Windows XP 128 MB RAM 500 MB free hard disk space Min PDA requirements HP ipac 38xx, 39xx Windows Pocket PC 64 MB RAM 64 MB SD-card (optional) For certain PDA types installation and program setup will be lost if the battery is drained. 2 VI.JE.N1.02 Danfoss 11/2004 DH-SMT

5 Cables Between PC and ECL Apex 10 controller: Order code no. 080Z0262 Between PDA cable and ECL Apex 10 controller or between null modem cable and ECL Apex 10 controller: Order code no. 080Z0261 Connection of the PDA - RS 232 cable with PDA plug: Is to be delivered by the PDA supplier. ECL Apex 10 PC / PDA / Modem (max. 15 m) DH-SMT VI.JE.N1.02 Danfoss 11/2004 3

6 How to install the program Insert the ECA-ST 101 disk into your CD ROM drive. In most systems the install program will automatically start immediately afterwards. If the installation window does not appear automatically, run the Install.exe program in the Programs directory of the ECA-ST 101 disk. Once the setup program is initialized, a Wizard will guide you through the installation process. Installation on PC 1. Choose Install Software on my Desktop PC Installation on PDA 1. Ensure that you have the Jeode Runtime program from Insignia a. If you have the ECA-ST 101B, proceed with step 2 b. If you have the ECA-ST 101A, install the Jeode runtime program in accordance with your software supplier s instructions. 2. Connect the PDA to a PC which has installed a synchronization program (supplied with the PDA) 3. Choose Install Software on my Pocket PC 4 VI.JE.N1.02 Danfoss 11/2004 DH-SMT

7 How to start the program 1. Connect the ECL Apex 10 to the device on to which the Service Tool is installed. 2. Switch on the supply for the controller. 3. Start the Service Tool: a. PC users: Choose Programs District Heating Service Tool b. PDA users: Choose Programs Service Tool When the program detects a new controller, system settings will be downloaded. This operation will take a couple of minutes. 4. Choose Direct in the Plant selection 5. Select user level: There are four user levels ranging from Default user (no logon) who is only allowed to read to Supervisor (SUPV) who has the highest authority. 6. Logon: The first time you enter the Service Tool, use 123 as access code. This is default from factory and can be used at all user levels until it is changed. After logon it is possible to operate the ECL Apex 10. Data and settings are described in the User guide: ECL Apex 10 and the Technical manual. DH-SMT VI.JE.N1.02 Danfoss 11/2004 5

8 Navigation Change user Log on to set / adjust the controller. Log off to prevent unauthorized use Circuit selection Each button accesses settings and data concerning the specific circuit Schedules Operation mode of the controller on a weekly / holiday basis Return to overview The button takes you back to the shown overview display Log function Historical and actual (trends) data Alarm bell An alarm is active 6 VI.JE.N1.02 Danfoss 11/2004 DH-SMT

9 Controller address Scroll down menu Choice of circuits Page navigation +/- buttons change page Communication Green icon: Controller is online Yellow icon: Connection being established Red icon: Controller is offline Configuration Accesses the setup menu Alarms List of active / cleared alarms and event log DH-SMT VI.JE.N1.02 Danfoss 11/2004 7

10 Authorization To get access to this menu you must be logged on as SUPV. Only as Supervisor you are able to create and authorize other users and change their access codes. There are four different user levels: Default (DFLT) Readout only. Logon is not required. Daily user (DAIL) The typical daily user is the person responsible for the daily operation of the heating system. The daily user can change operational data, read and cancel alarms. Service user (SERV) The typical service user is the installer or service engineer, who installs and runs in the heating system. The service user can change more radical settings. Supervisor (SUPV) The typical supervisor is the system designer, who has the top-level responsibility for the heating system. The supervisor has the exclusive rights to authorize other users. How to get authorized Choose SUPV in the Logon to Service Tool display and enter the access code (ex factory the SUPV access code is set to 123 ). Push the configuration button and choose Authorization. It is now possible to create and authorize new users and change their access codes. 8 VI.JE.N1.02 Danfoss 11/2004 DH-SMT

11 How to create new users 1. Choose»Add«to insert a new user 2. Give the new user a»user name«, max length 4 characters 3. Give the new user a User ID between 0 and 999, which has not been used already 4. Choose an Access code between 0 and Select the preferred Language 6. Assign the User profile for the new user 7. Select how the measurement unit ( Unit ) has to be displayed. End this session by pushing the OK button DH-SMT VI.JE.N1.02 Danfoss 11/2004 9

12 10 VI.JE.N1.02 Danfoss 11/2004 DH-SMT

13 DH-SMT VI.JE.N1.02 Danfoss 11/