CFW09 Vectrue Inverter Variable Frequency Drives

Transcription

1 Vectrue Inverter The WEG Series of incorporates the world s most advanced technology in drives for three-phase AC induction motors. The Vectrue Technology represents a significant advancement, allowing this new generation of WEG VFD s to combine V / F, Sensorless Vector and Closed Loop Vector (with encoder) control techniques all in one product. WEG innovated and simplified braking torque for special applications. Optimal Braking eliminates the need for the dynamic braking resistor in some applications allowing a simpler, more compact and economic solution. Applications Pumps Fans / Blowers Conveyors Compressors Agitators and Mixers Extruders Grizzly Feeders Centrifuges Cranes and Hoists Rollout Tables Presses Saws Standard Features Same programming as all other WEG VFD's V/Hz or Sensorless Vector Control via parameter selection Self Tuning to motor parameters NEMA 1 Enclosure up to 200HP IP20 Finger Safe Enclosure from 250 to 500HP V or V input voltage Single or Three-phase input voltage up to 3HP/230V 150% current overload capacity DC bus connections accessible Detachable Smart Keypad with dual display and Copy Function 32 bit RISC microprocessor controlled PWM output 1.25 / 2.5 / 5 / 10 khz adjustable switching frequency Six isolated programmable digital inputs Three programmable relay outputs (250Vac / 1A) Two non isolated programmable analog inputs Two non isolated programmable analog outputs Protective features: Over current, motor overload, drive over temperature, output phase-to-phase and phase-to-ground short circuit, DC bus over and under voltage, power supply under voltage and phase loss and external fault Optional Features Closed loop vector control Remote keypad with cable and mounting frame RS-232 or RS-485 Serial Interface On/Off line PC programming with Superdrive Fieldbus Comm: Profibus DP, DeviceNet or Modbus RTU* Encoder buffered output Additional digital and analog I/O Dynamic Braking Resistors available for most models *Requires optional RS-232 or RS- 485 Interface Control features: Linear and S amp acceleration and deceleration, local/remote control, DC braking, torque boost, motor slip compensation, electronic pot, preset speeds, adjustable V/Hz profile, maximum and minimum adjustable motor speed limits, three skip frequencies, adjustable output current limit, JOG, ride-thru, flying start and PID regulator Display readings: speed, frequency, voltage, current and torque, output power (kw), last four faults, drive status, digital and analog I/O status, hours powered and hours running Ambient: 32ºF (0ºC) to 104ºF (40ºC), 3300 ft (1000m) altitude, 90% humidity, non- condensing. SuperDrive (G1) compatible A ASK-4WEG Data is subject to change without notice.

2 to 500 HP T 4 G 5 6 Z 1. series 2. Rated Current: 0006 = 6 Amps 0024 = 24 Amps 0240 = 240 Amps 0600 = 600 Amps 3. Number of Phase: T = Three Phase 4. Input Voltage D = VAC G = VAC H = VAC 5. Options: Blank = No additional accessories DB = Factory Added braking chopper 6. End of code: Z Data is subject to change without notice. WEG Automation - Products and Solutions A-27

3 Vectrue Inverter Vectrue Inverter A complete, flexible and compact product NEMA 1 / IP20 Enclosure Optional RS-232 Interface Module for PC Communication Flange for Through Surface Mounting 7 Segment LED Display Detachable Keypad with Multi-language Double Display (LCD + LED) and Copy Function 2 Lines with 16 Characters LCD Display High Performance 32 bit RISC Microprocessor Optional Fieldbus Communication Modules for: - Profibus DP - DeviceNet - Modbus RTU Standard SMD Control Board for all Models 6 Programmable Isolated Digital Inputs 2 Programmable Analog Inputs Optional I/O Expansion Boards for: - RS-485 Serial Interface - Additional Inputs/ Outputs - Encoder Feedback 3 Programmable Relay Outputs Metallic Conduit Connection System 2 Programmable Analog Outputs AC Supply Input Connection Output DC Bus Connection for: - DC Bus Choke - Common DC Bus - Regenerative Rectifier A ASK-4WEG Data is subject to change without notice.

4 Keypad LED Display Intelligent Keypad Intelligent operator interface with double display, LED (7 segment) and LCD (2 lines with 16 characters), providing optimum distant viewing along with a detailed description of all parameters and messages. LCD Display Selectable Language The language of the LCD display messages can be selected by the operator. English, Spanish and Portuguese are available. REVERSE LED FORWARD LED Keypad Functions LOCAL LED REMOTE LED Oriented Start-up The Oriented Start-up feature was specially created to facilitate and expedite the start-up procedure. At the first power-up or after a reset to factory default parameters, an automatic programming routine guides the operator through a sequence of steps to plug in the minimum parameters necessary for a perfect relationship between drive and motor. Starts the VFD via a controlled acceleration ramp. When running switches the display indication: rpm - Volts - Status - Torque - Hz -Amps Stop the VFD via a controlled deceleration ramp. Resets the VFD after a fault trip has occurred. Increases the speed or parameter number/content. Copy Function This intelligent keypad also incorporates a Copy Function, which allows copying parameters from one drive to others, providing easy and reliable programming repeatability for duplicate applications. Keypad can store two complete sets of user parameters. Decreases the speed or parameter number/content. Switches the display between the parameter number and its content (position/content) for programming VFD A VFD B While pressed the motor is run at JOG speed. FWD/REV key. When pressed reverses the direction of rotation. Keypad Keypad Selects the VFD operating mode as Local or Remote. Data is subject to change without notice. WEG Automation - Products and Solutions A-29

5 NEMA 1 Enclosure and compact product CFW10 CFW08 CFW700 CFW11 Volts 230V 460V HP Drive AMPS CT* VT* CT* VT* Catalog Number Braking Transistor Frame Size Dimensions (in.) H x W x D App. Shpg. Wt. (lbs.) List Price Multiplier Symbol INPUT POWER SUPPLY: SINGLE OR THREE-PHASE - 230V 1 or CFW TDZ X 5.6 X $1,295 V1 2 7 CFW TDZ YES X 5.6 X $1,350 V CFW TDZ X 5.6 X $1,410 V1 INPUT POWER SUPPLY: THREE-PHASE - 230V 3 13 CFW TDZ X 5.6 X $1,440 V CFW TDZ X 7.2 X $1,542 V CFW TDZ YES X 7.2 X $2,020 V CFW TDZ X 7.2 X $2,201 V CFW TDZ X 8.9 X $3,310 V CFW TDZ X 9.8 X $4,400 V CFW TDZ X 13.2 X $6,600 V1 NO use CFW CFW TDZ X 13.2 X $7,222 V1 090XXXTDDBZ CFW TDZ X 13.2 X $9,000 V1 BELOW CFW TDZ X 13.2 X $9,909 V CFW TDZ X 13.2 X $10,590 V CFW TDDBZ (!) X 9.8 X $4,788 V CFW TDDBZ X 13.2 X $6,767 V CFW TDDBZ X 13.2 X $8,063 V CFW TDDBZ YES X 13.2 X $9,490 V CFW TDDBZ (!) X 13.2 X $10,550 V CFW TDDBZ (!) X 13.2 X $12,114 V CFW TDZ EXTERNAL** X 16.1 X $13,750 V CFW TDZ (!) X 16.1 X $19,600 V1 INPUT POWER SUPPLY: THREE PHASE - 460V 1 or CFW TGZ x 5.6 x $1,469 V CFW TGZ x 5.6 x $1,500 V CFW TGZ x 5.6 x $1,556 V1 5 9 CFW TGZ YES x 5.6 x $1,790 V CFW TGZ x 7.2 x $1,880 V CFW TGZ x 7.2 x $2,300 V CFW TGZ x 7.2 x $2,720 V CFW TGZ x 8.9 x $3,873 V CFW TGZ x 9.8 x $4,300 V CFW TGZ x 9.8 x $5,400 V CFW TGZ NO USE CFW x 13.2 x $6,030 V CFW TGZ 09XXXTGDBZ x 13.2 x $7,500 V CFW TGZ BELOW x 13.2 x $8,900 V CFW TGZ x 13.2 x $10,650 V CFW TGZ x 13.2 x $12,500 V CFW TGDBZ x 9.8 x $4,800 V CFW TGDBZ x 9.8 x $6,344 V CFW TGDBZ x 13.2 x $8,317 V CFW TGDBZ YES x 13.2 x $9,300 V CFW TGDBZ x 13.2 x $11,500 V CFW TGDBZ x 13.2 x $13,600 V CFW TGDBZ x 13.2 x $15,900 V CFW TGZ x 16.1 x $17,500 V CFW TGZ x 16.1 x $21,000 V CFW TGZ x 16.1 x $23,000 V CFW TGZ x 27.5 x $29,366 V1 EXTERNAL** CFW TGZ x 27.5 x $31,314 V CFW TGZ x 27.5 x $41,027 V CFW TGZ x 27.5 x $43,970 V CFW TGZ x 27.5 x $50,088 V1 * CT = Constant Torque; VT = Variable Torque ** See Options and Accessories Notes: 1) "HP" rating based on TABLE NEC. ALWAYS compare motor FLA to Nominal AMPS of drive. 2) Above 200HP enclosure is IP20 "finger safe". 3) All 575V drives are non-stocked items, consult WEG for availability. A ASK-4WEG Data is subject to change without notice.

6 NEMA 1 Enclosure and compact product Volts 575V HP Drive Amps CT* VT* CT* VT* Catalog Number INPUT POWER SUPPLY: THREE PHASE - 575V CFW THZ Braking Transistor Frame Size Dimensions (in.) H x W x D App. Shpg. Wt. (lbs.) CFW THZ x 7.2 x $2,131 V1 YES CFW THZ x 7.2 x $2,229 V1 List Price Multiplier Symbol x 7.2 x $1,607 V CFW THZ x 7.2 x $1,665 V CFW THZ x 7.2 x $2,711 V CFW THZ x 7.2 x $3,023 V CFW THZ x 9.8 x $3,873 V CFW THZ x 9.8 x $4,552 V CFW THZ NO USE CFW x 9.8 x $6,197 V CFW THZ CFW THZ 09XXXTHDBZ BELOW x 13.2 x x 13.2 x $8,258 $9,746 V1 V CFW THZ x 13.2 x $11,600 V CFW THZ x 13.2 x $14,117 V CFW THDBZ x 9.8 x $4,311 V CFW THDBZ x 9.8 x $5,084 V CFW THDBZ x 9.8 x $6,892 V CFW THDBZ YES x 13.2 x $8,965 V CFW THDBZ x 13.2 x $10,497 V CFW THDBZ x 13.2 x $12,576 V CFW THDBZ x 13.2 x $15,992 V1 INPUT POWER SUPPLY: THREE PHASE to 690V CFW THZ 8E 45.1 x 16.1 x $17,182 V CFW THZ 8E 45.1 x 16.1 x $25,211 V CFW THZ 8E 45.1 x 16.1 x $34,172 V CFW THZ 10E 46.7 x 27.6 x $36,040 V1 EXTERNAL** CFW THZ 10E 46.7 x 27.6 x $39,039 V CFW THZ 10E 46.7 x 27.6 x $52,458 V CFW THZ 10E 46.7 x 27.6 x $56,553 V CFW THZ 10E 46.7 x 27.6 x $60,186 V1 Constant Torque; VT = Variable Torque ** See Options and Accessories Notes: 1) HP rating based on TABLE NEC. ALWAYS compare motor FLA to Nominal AMPS of drive. 2) Above 200HP enclosure is IP20 finger safe. 3) All 575V drives are non-stocked items, consult WEG for availability. Data is subject to change without notice. WEG Automation - Products and Solutions A-31

7 CFW10 CFW08 CFW700 CFW11 Options and Accessories Dynamic Braking Keypads Keypad Cables Communication *see note Caps I/O Expansion Boards Thru Surface Mounting Remote Stations Description Catalog Number List Multiplier Price Symbol External Dynamic Braking Module for 180A Model (16 X 9 X 10 NEMA 1 Enclosure) DBW010165D36801 $1,902 V1 External Dynamic Braking Module for 211 & 240A Models (16 X 9 X 10 NEMA 1 Enclosure) DBW010240D36801 $2,429 V1 External Dynamic Braking Module for 312, 361,450,515, & 600A Models (16 X 9 X 10 NEMA 1 Enclosure) DBW010300D36801 $2,963 V1 External Dynamic Braking Module for 107,147,211,& 247A Models at 575V (16 X 9 X 10 NEMA 1 Enclosure) DBW020210D50691 (!) $3,702 V1 External Dynamic Braking Module for 315 & 343A Models at 575V (16 X 9 X 10 NEMA 1 Enclosure) DBW020300D50691 (!) $4,882 V1 External Dynamic Braking Module for 418 & 472 Amp Models at 575V (16 X 9 X 10 NEMA 1 Enclosure) DBW020380D50691 (!) $6,052 V1 Standard Keypad with LED & LCD HMI--LCD $202 V1 NEMA 4/IP56 Remote Keypad with LED & LCD HMI--LCDN4 $261 V1 Remote Keypad FRAME KIT KMR- $88 V1 Blank Keypad with Power & Error LED s TCL- $27 V1 3.3ft Remote Keypad Cable CAB-HMI-09-1 $33 V1 6.6ft Remote Keypad Cable CAB-HMI-09-2 $39 V1 10ft Remote Keypad Cable CAB-HMI-09-3 $48 V1 16ft Remote Keypad Cable CAB-HMI-09-5 $72 V1 25ft Remote Keypad Cable (Requires KMR-) CAB-HMI-09-7 $86 V1 33ft Remote Keypad Cable (Requires KMR-) CAB-HMI-0910 $105 V1 Superdrive PC Communication Kit (includes software & hardware accessories) KSD- $156 V1 RS-232 Serial Interface KCS- $84 V1 Profibus DP Communication Kit KFB-PD $993 V1 DeviceNet Communication Kit KFB-DN $872 V1 Ethernet IP Communication Kit (V3.70 or superior) KFB-EN $1,608 V1 DeviceNet Profile Communication Kit (V2.27 or superior) KFB-DD (!)$1,094 V1 External DC Bus Cap Kit 1500uF (includes bleed resistor, mounting bracket, & screws) KIT KCE-/1500uF $114 V1 External DC Bus Cap Kit 4700uF (includes bleed resistor, mounting bracket, & screws) KIT KCE-/4700uF $284 V1 I/O Exp. Board A with Encoder Input, Encoder Output, RS-485 Serial Interface, I4 bit A/D, I4 bit D/A s, Digital Inputs and Outputs + Thermistor (PTC) Input EBA.01- $1,345 V1 I/O Exp. Board A with RS-485 Serial Interface, Digital Inputs and Outputs + Thermistor (PTC) Input EBA.02- $317 V1 I/O Exp. Board A with I4 bit A/D, I4 bit D/A s, Digital Inputs and Outputs + Thermistor (PTC) Input EBA.03- $621 V1 I/O Exp. Board B with Encoder Input, Encoder Output, RS-485 Serial Interface, Isolated Analog Input, Isolated Analog Outputs, Digital Inputs and Outputs + Thermistor (PTC) Input EBB.01- $1,133 V1 I/O Exp. Board B with Encoder Input, Digital Inputs and Outputs + Thermistor (PTC) Input EBB.02- $533 V1 I/O Exp. Board B with Isolated Analog Input, Isolated Analog Outputs, Digital Inputs and Outputs + Thermistor (PTC) Input EBB.03- $634 V1 I/O Exp. Board B with Encoder Input, 5V Power Supply for Encoder, Buffered Outputs for Encoder Signals, RS-485 Serial Port, 24V Digital Input, 2 X 24V OC Digital Outputs, 0 10V/4-20mA Analog Input, 2 X 4-20mA Analog Outputs and PTC EBB.04- $1,413 V1 Thermistor Input I/O Exp. Board B with 2 X 4-20mA Analog Outputs EBB.05- $426 V1 I/O Exp. Board C with Encoder Input, 5-15VDC External Power Supply EBC1.01- $184 V1 I/O Exp. Board C with Encoder Input with internal Power Supply - 5VDC EBC1.02- (!) $511 V1 I/O Exp. Board C with Encoder Input with internal Power Supply - 12VDC EBC1.03- $529 V1 I/O Exp. Board E with RS-485 Serial Interface, Digital Inputs and Outputs + Thermistor (PTC) Input EBE.01- $183 V1 PLC/Motion Control Board PLC1.01 $985 V1 PLC/Motion Control Board PLC2.00 $1,170 V1 Kit for Through Surface Mounting - Size 3 KMF--M3 $17 V1 Kit for Through Surface Mounting - Size 4 KMF--M4 $20 V1 Kit for Through Surface Mounting - Size 5 KMF--M5 $23 V1 Kit for Through Surface Mounting - Size 6 KMF--M6 $26 V1 Kit for Through Surface Mounting - Size 7 KMF--M7 $29 V1 Kit for Through Surface Mounting - Size 8 KMF--M8 $36 V1 Remote Station-includes Start PB, Stop PB, 1-NC and 1-NO contact block, Potentiometer 5k and legends (22mm) replaces CFW-REM Remote Station-includes Start PB, Stop PB, 1-NC and 1-NO contact block, Potentiometer 5k and legends (30mm) replaces CFW-REM CSW-SP3PBS $460 Z5 CSW30-SP3PBS $535 Z5 Notes: (!) Non-Stocked Item, consult WEG for availability *Mobus RTU - Requires optional RS-232 or RS-485 Interface A ASK-4WEG Data is subject to change without notice.

8 Options and Accessories Complete Keypad (Standard) HMI LCD Intelligent Operator Interface with double display (LED and LCD), plain English messages and COPY Function. Local or remote installation. NEMA 4 Remote Keypad HMI LCDN4 NEMA 4/IP55 remote keypad, for installation on panel door or remote operator station in harsh environments, such as splashing or hose-directed water and windblown dust. Maximum cable length: 33ft (10m) Remote Keypad Frame Kit KMR Frame for remote keypad mounting on panel door or operator station. Optional up to 15ft (5m) cable. Maximum cable length; 33 ft (10m) Remote Keypad Cables CAB HMI 09 X Cables with lengths (x) of 3.3, 6.6, 10,,15, 25 and 33ft (1, 2, 3, 5, 7.5 and 10m) 7.5 and 10m must use the KMR frame kit. Special cables available upon request. Remote Control Station-22mm CSW-SP3PBS The remote control station is a 3-hole NEMA 4 pushbutton station with 22mm Start and Stop push buttons and a 5K potentiometer. Alternative configurations are available, consult factory for details. Remote Control Station-30mm CSW30-SP3PBS The remote control station is a 3-hole NEMA 4 pushbutton station with 30mm Start and Stop push buttons and a 5K potentiometer. Alternative configurations are available, consult factory for details. Alternative configurations are available, consult factory for details. RS-232 Serial Interface KCS RS-232 Serial Interface Module to connect the to a PC or other equipment via a RS-232 Serial Link. PC Communication Kit KSD WEG Superdrive is a windows based software program that allows serial (RS-232 or RS-485) communication between a PC and WEG Soft Starters and. Superdrive is an excellent programming, documentation and troubleshooting tool for WEG Soft Starters and VFD s. Superdrive is available for free download at Hardware accessories may be required, depending on the Soft Starter or VFD line. Not available for SSW06. Data is subject to change without notice. WEG Automation - Products and Solutions A-33

9 Options and Accessories CFW10 CFW08 PLC / Motion Control Board PLC 1.01 & PLC 2.00 PLC-01 / PLC-02 : WEG Integral PLC The PLC01/02 boards add important PLC (Programmable Logical Controller) functions to the CFW-09, enabling the execution of complex logic program by using the digital and analog inputs and outputs as well as the digital and analog inputs and outputs of the own inverter which can be accessed by the user program. Functions include simple contacts and coils up to functions that uses floating point, such as sum, subtraction, multiplication, division, trigonometry, square root functions, etc. Other important functions are the PID blocks, high-pass and low-pass filters, saturation, comparison. All these functions operate with floating point. Besides the functions mentioned above, the PLC1 provides blocks for motor speed and motor position control, that is a trapezoidal-profile positioning and a S-profile positioning, speed reference generation with trapezoidal acceleration ramp, etc. (Note: when position functions used, the coupling of an encoder on motor shaft is required). All functions can interact with the user through the 100 programmable parameters that can be accessed directly through the inverter HMI. The texts and user units of the programmable parameters can be customized by the WLP. Ethernet IP KFB - EN ProfiBus DP KFB - PD DeviceNet KFB - DN I/O EXPANSION BOARDS EBA.0X - EBB.0X - EBC1.0X - EBE.0X - CFW700 CFW11 Available Features EBA-XX EBB-XX EBC-XX EBE Standard Encoder Input 12VDC Encoder output VDC Analog inputs 10bits Analog inputs 14bits Isolated analog inputs 10bits Isolated digital inputs Isolated PTC input Isolated RS Isolated AO 0..10V - 0/4...20mA Isolated transistor output Analog outputs 14bits Encoder Input ext. supply 5VDC Encoder Input 5VDC Relay outputs 1A 240VAC A ASK-4WEG Data is subject to change without notice.

10 DB Resistors DB Resistors 10% Duty Cycle Volts 230 V 460V HP For Use with CFW-09 Model Number: Catalog Number OHMS WATTS Dimensions H x W x D List Price Multiplier Symbol 1.5 CFW TDZ CFDB39-224* X 5 X 4 $183 V1 2 CFW TDZ CFDB27-298* X 5 X 4 $183 V1 3 CFW TDZ CFDB27-298* X 5 X 4 $183 V1 3 CFW TDZ CFDB X 5 X 4 $183 V1 5 CFW TDZ CFDB22-373* X 5 X 4 $183 V1 7.5 CFW TDZ CFDB X 7 X 5 $319 V1 10 CFW TDZ CFDB X 7 X 5 $319 V1 15 CFW TDZ CFDB X 10 X 5 $481 V1 20 CFW TDDBZ CFDB X 16 X 5 $795 V1 25 CFW TDDBZ CFDB X 10 X 5 $944 V1 30 CFW TDDBZ CFDB X 13 X 5 $1,092 V1 40 CFW TDDBZ CFDB X 10 X 5 $1,508 V1 50 CFW TDDBZ CFDB X 10 X 5 $1,508 V1 1.5 CFW TGZ CFDB * X 5 X 4 $183 V1 2 CFW TGZ CFDB * X 5 X 4 $183 V1 3 CFW TGZ CFDB * X 5 X 4 $183 V1 5 CFW TGZ CFDB47-746* X 7 X 5 $319 V1 7.5 CFW TGZ CFDB47-746* X 7 X 5 $319 V1 10 CFW TGZ CFDB33-746* X 7 X 5 $319 V1 15 CFW TGZ CFDB X 10 X 5 $481 V1 20 CFW TGZ CFDB X 13 X 5 $638 V1 25 CFW TGDBZ CFDB X 10 X 5 $996 V1 30 CFW TGDBZ CFDB X 10 X 5 $996 V1 40 CFW TGDBZ CFDB X 10 X 5 $1,044 V1 50 CFW TGDBZ CFDB X 10 X 5 $1,044 V1 60 CFW TGDBZ CFDB X 10 X 5 $1,389 V1 75 CFW TGDBZ CFDB X 13 X 5 $1,848 V1 100 CFW TGDBZ CFDB X 16 X 5 $2,062 V1 150 CFW TGZ** CFDB X 13 X 10 $2,957 V1 150 CFW TGZ** CFDB X 13 X 10 $3,557 V1 200 CFW TGZ** CFDB X 13 X 10 $3,557 V1 250 CFW TGZ** CFDB X 13 X 15 $5,247 V1 300 CFW TGZ** CFDB X 13 X 15 $5,247 V1 350 CFW TGZ** CFDB X 24 X 24 $6,733 V1 450 CFW TGZ** CFDB X 24 X 30 $9,952 V1 500 CFW TGZ** CFDB X 24 X 30 $9,952 V1 Note: These are non-stocked items, consult WEG for availability. **External DB Transistor Module DBWXXXXD36801 must be ordered Data is subject to change without notice. WEG Automation - Products and Solutions A-35

11 DB Resistors DB Resistors 20% Duty Cycle - NEMA 1 Enclosure CFW10 CFW08 CFW700 CFW11 Volts 230 V 460V HP For Use with CFW-09 Model Number: Catalog Number OHMS WATTS Dimensions H x W x D List Price Multiplier Symbol 1.5 CFW TDZ CFDB39-224* X 5 X 4 $183 V1 2 CFW TDZ CFDB27-298* X 5 X 4 $183 V1 3 CFW TDZ CFDB27-448* X 7 X 5 $319 V1 3 CFW TDZ CFDB X 7 X 5 $319 V1 5 CFW TDZ CFDB22-746* X 7 X 5 $319 V1 7.5 CFW TDZ CFDB , X 10 X 5 $481 V1 10 CFW TDZ CFDB , X 16 X 5 $795 V1 15 CFW TDZ CFDB X 13 X 5 $1,092 V1 20 CFW TDDBZ CFDB X 10 X 5 $1,215 V1 25 CFW TDDBZ CFDB X 10 X 5 $1,403 V1 30 CFW TDDBZ CFDB X 10 X 5 $1,403 V1 40 CFW TDDBZ CFDB X 13 X 5 $1,870 V1 50 CFW TDDBZ CFDB X 13 X 5 $1,870 V1 1.5 CFW TGZ CFDB * X 5 X 4 $183 V1 2 CFW TGZ CFDB * X 5 X 4 $183 V1 3 CFW TGZ CFDB * X 7 X 5 $319 V1 5 CFW TGZ CFDB47-746* X 7 X 5 $319 V1 7.5 CFW TGZ CFDB * 47 1, X 10 X 5 $481 V1 10 CFW TGZ CFDB * 33 1, X 13 X 5 $638 V1 15 CFW TGZ CFDB X 10 X 5 $944 V1 20 CFW TGZ CFDB X 10 X 5 $944 V1 25 CFW TGDBZ CFDB X 10 X 5 $1,293 V1 30 CFW TGDBZ CFDB X 10 X 5 $1,385 V1 40 CFW TGDBZ CFDB X 13 X 5 $1,708 V1 50 CFW TGDBZ CFDB X 16 X 5 $2,032 V1 60 CFW TGDBZ CFDB X 13 X 10 $2,595 V1 75 CFW TGDBZ CFDB X 13 X 10 $2,957 V1 100 CFW TGDBZ CFDB X 13 X 10 $3,557 V1 150 CFW TGZ** CFDB X 13 X 15 $5,644 V1 150 CFW TGZ** CFDB X 24 X 18 $6,706 V1 200 CFW TGZ** CFDB X 24 X 18 $6,706 V1 250 CFW TGZ** CFDB X 24 X 30 $9,516 V1 300 CFW TGZ** CFDB X 24 X 30 $9,516 V1 350 CFW TGZ** CFDB X 24 X 37 $13,717 V1 400 CFW TGZ** CFDB X 24 X 38 $14,084 V1 500 CFW TGZ** CFDB X 24 X 38 $14,084 V1 Note: These are non-stocked items, consult WEG for availability. **External DB Transistor Module A ASK-4WEG Data is subject to change without notice.

12 and CFW11 Line & Load Reactors Line and Load Reactors 3% Z (Impedance) NEMA 1 Enclosure Volts 230V 460V HP Reactor AMPS Catalog Number Dimensions H x W x D App. Shpg. Wt. (lbs.) List Price Multiplier Symbol 3 12 LRW012D3N1 8 x 8 x 6 16 $436 V LRW018D3N1 8 x 8 x 6 16 $512 V LRW025D3N1 13 x x $590 V LRW035D3N1 13 x x $634 V LRW045D3N1 13 x x $756 V LRW055D3N1 13 x x $890 V1 25/30 80 LRW080D3N1 13 x x $905 V LRW100D3N1 13 x x $1,086 V LRW130D3N1 13 x x $1,175 V LRW160D3N1 13 x x $1,424 V LRW200D3N1 13 x x $1,488 V LRW002G3N1 8 x 8 x 6 11 $387 V1 2/3 4 LRW004G3N1 8 x 8 x 6 11 $394 V1 5 8 LRW008G3N1 8 x 8 x 6 14 $425 V LRW012G3N1 8 x 8 x 6 16 $452 V LRW018G3N1 8 x 8 x 6 16 $519 V LRW025G3N1 13 x x $634 V1 20/25 35 LRW035G3N1 13 x x $654 V LRW045G3N1 13 x x $855 V LRW055G3N1 13 x x $948 V1 50/60 80 LRW080G3N1 13 x x $1,179 V LRW100G3N1 13 x x $1,168 V LRW130G3N1 13 x x $1,468 V LRW160G3N1 13 x x $1,994 V LRW200G3N1 13 x x $1,758 V LRW250G3N1 24 x x $2,990 V LRW320G3N1 24 x x $3,233 V LRW400G3N1 24 x x $4,962 V1 350/ LRW500G3N1 47 x 26.5 x $6,768 V1 450/ LRW600G3N1 47 x 26.5 x $7,329 V1 750/ LRW1000G3N1 available upon request $10,651 V1 Note: These are non-stocked items, consult WEG for availability. Data is subject to change without notice. WEG Automation - Products and Solutions A-37

13 Technical Data Power Supply Voltage Three Phase V: 220 / 230 V (+10%, -15%) - 1 ø up to 3HP without de-rating V: 380 / 400 / 415 / 440 / 460 / 480 V (+10&, -15%) Frequency 50 / 60 Hz +/- 2 Hz (48 62 Hz) Phase Unbalance Up to 3% Cos (Displacement Power Factor) Greater than 0.98 Enclosure Control Performance Control Inputs Control Outputs Communication Safety Degree of Protection NEMA 1 / IP 20 (sizes 1 to 8) IP 20 (Sizes 9 and 10) Finishing Color Plastic Cover Light Gray PANTONE 413C (sizes 1 and 2) Metallic Cover and Sides Light Gray RAL 7032 (sizes 3 to 10) Power Supply Microprocessor PWM Technique Control Modes Switching Frequency Frequency Range Overload Capacity Base Dark Gray RAL 7022 (sizes 3 to 10) Switched Mode Power Supply Fed from the DC Link 32 bit RISC Technology SVM Sine wave PWM (Space Vector Modulation) Software Implemented Current, Flux and Speed Regulators (Full Digital) Scalar (Voltage Source V/F) Sensorless Vector (without encoder) Flux Vector with Encoder 1.25 / 2.5 / 5.0 / 10 khz Hz for V / F and Vector with Encoder Control (60 Hz ) Hz for V / F and Vector with Encoder Control (50 Hz ) Hz for Sensorless Vector Control (50 or 60 Hz ) 150% for 60 seconds, every 10 minutes 180% for 1 second every 10 minutes Efficiency Greater than 97% Speed Control V / F Mode Regulation (with Slip Compensation) 1% of Rated Speed Resolution : 1 rpm (keypad reference) Speed Regulation Range : 20:1 Sensorless Vector Mode Regulation : 0.5% of Rated Speed Resolution : 1 rpm (keypad reference) Range : 100:1 Flux Vector Mode wih Encoder Regulation with: 10 bit Analog Reference: +/- 0.1% of Rated Speed 14 bit Analog Reference: +/- 0.01% of Rated Speed1 Digital Reference (Ex: Keypad or Serial): +/- 0.01% of Rated Speed Range : Down to 0 rpm Torque Control Flux Vector Modes Regulation: +/- 10% of Rated Torque Range : 0 150% of Rated Torque Analog 2 Programmable Differential Inputs (10 bit) : 0 10 V, 0 20 ma or 4 20 ma (Non isolated) 1 Programmable Isolated Bipolar Input (14 bit) : V, 0 20 ma or 4 20 ma with expansion board EBA.01 1 Programmable Isolated Input (10 bit) : 0 10 V, 0 20 ma or 4 20 ma with expansion board EBA.01 Digital 6 Programmable Isolated Input : 24 Vdc 1 Programmable Isolated Input : 24 Vdc with expansion board 1 Programmable Isolated Input : 24 Vdc (for PTC Thermistor) with expansion board Encoder 1 Differential Input, with 12 Vdc Internal Isolated Power Supply (14 bit resolution) 1 Analog 2 Programmable Outputs (11 bit) : 0 10 V (Non isolated) 2 Programmable Bipolar Outputs (14 bit) : V 1 2 Programmable Isolated Outputs (11 bit) : 0 20 ma or 4 20 ma 1 Relay 2 Programmable Outputs, Form C Contacts (NO/NC) : 240 Vac, 1 A 1 Programmable Output, Form A Contact (NO) : 240 Vac, 1 A Transistor 2 Programmable Isolated Outputs (Open Collector) : 24 Vdc, 50 ma 1 Encoder 1 Isolated Differential Encoder Signals Output : 5 15 Vdc External Power Supply 1 Serial RS-232 with KCS- Kit 1 RS-485, Isolated, with EBA, EBE or EBB Board 1 Field Bus Profibus DP, DeviceNet or Modbus RTU, with KFB kits 1 Protections DC Link Over Voltage Output Short Circuit DC Link Under Voltage Output Ground Fault VFD Over Temperature External Fault Over Temperature 1 Self-diagnosis Fault Output Over Current Programming Error Overload (i x t) Serial Communication Fault Dynamic Braking Resistor Overload or Encoder Connection Fault CPU / EPROM Error (Watchdog) Power Supply Phase Fault (30 A and above models) Encoder Fault Keypad Connection Fault A ASK-4WEG Data is subject to change without notice.

14 Technical Data Ambient Conformities Temperature Humidity Altitude EMC Directive 89 / 336/ EEC EN LVC 73/23/EEC IEC 146 UL 508 C EN ºF (40ºC), up to 122ºF (50ºC) with 2% / ºC Output Current De-rating 5 90% Non Condensing ft (1000 m) (up to ft (4000 m) with 10% / 1000 m Output Current De-Rating Electromagnetic Compatibility Industrial Environment EMC - Emission and Immunity Low Voltage Directive Semiconductor Inverters Power Conversion Equipment Electronic Equipment for use in power installations EN Saftey Requirements for Electrical Equipment for Measurement, Control and Laboratory Use Certifications UL (USA) and cul (Canada) Underwriters Laboratories Inc. USA Keypad Control Features and Options CE (Europe) Programming Commands Monitoring Standard Options Phoenix Test - Labs GmbH - Germany General VFD Functions Programming Start / Stop, Increase / Decrease Speed, JOG, FWD/REV and Local/Remote Speed Reference (rpm) Output Current (A) Speed (rpm) Output Voltage (Vac) Speed Proportional Value (Ex: ft/min) VFD Status Output Frequency (Hz) Digital Inputs Status DC Link Voltage (Vdc) Transistor Outputs Status Torque (%) Relay Outputs Status Output Power (kw) Analog Inputs Value Hours Powered Up (h) Four Last Faults Hours Enabled (h) Fault Messages Keypad with LCD + LED displays (HMI:--LCD) Password to protect VFD programming LCD display language selection: English, Spanish and Portuguese Control mode selection (via parameter): V / F, Sensorless Vector or Vector with Encoder Fault auto-diagnosis and auto-reset Parameters reset to factory or user default VFD Self-tning to motor and load (Vector Modes) Specific unit indication (Ex: I/s, th, %, etc) slip compensation (V / F Mode) Manual and automatic Torque Boost (V / F Mode) Adjustable V / F Curve (V / F Mode) Minimum and maximum speed limits Output current limit Adjustable motor overload protection Digital gain and offset adjustments for the analog inputs Digital gain adjustments for the analog outputs JOG function JOG +/ JOG - function (momentary speed increase/decrease, phase shift) COPY function (VFD / Keypad or Keypad / VFD) Comparison functions for the digital outputs: N*> Nx; N> Nx; N < Nx; N = 0; N = N*; Is > Ix; Is < Ix; T > Tx and T < Tx Where: N = speed; N* = Speed reference is; Is = Output current and T = torque Linear and S independent acceleration and deceleration ramps, two sets of ramps DC Braking Optimal Braking (Vector Modes) Built-in dynmanic braking transistor - Models up to 45A / V and 30A / V Multi-speed function (up to 8 preset speeds) Speed Profiling function Hour meter and Wattmeter PID regulation (for automatic control of level, pressure, flow, etc.) FWD / REV selection Local / Remote operation selection Flying start function (restart with tne motor spinning) Skip speed (critical speed rejection) Ride-through (operation during momentary power loss) Built-in dynamic braking transistor: Models A / V and A / V Remote keypad cable (3.3, 6.6, 10,16, 25 and 35ft) Blank keypad for local installation Blank keypad for remote installation Remote Keypad frame kit I/0 Expansion Boards FieldBus Communications Kit (Mounted inside VFD) WEG Automation - Products and Solutions Data is subject to change without notice. A-39