X2Y - series Surface-mount ceramic EMI filter

Transcription

1 DISCRETE CERAMICS X2Y series Surface mount component June 2002 Rev 6 X2Y - series 2002 July 26 v1.07

2 X2Y Series Table of Contents 1. Introduction, Benefits, Applications 2. Available Capacitances & Voltage Ranges 3. Mechanical Data 4. NP0: 5. X7R: 6. Y5V: Selection Chart Electrical Characteristics Thickness Qualification and Packing quantities Selection Chart Electrical Characteristics Thickness Qualification and Packing quantities Selection Chart Electrical Characteristics Thickness Qualification and Packing quantities 7. Ordering information 8. Recommended Solder lands 9. Insertion loss characteristics and measurement setup 10. Tests & Requirements 11. Revision history

3 X2Y Series X2Y EMI FILTERS Phycomp s X2Y -series is a breakthrough in the design of ceramic multilayer products for decoupling and filtering in an IPD (integrated passive device). X2Y products are comprised of two identical Y-capacitors and one X-capacitor, integrated into a 4-terminal device, which is available in standard MLCC sizes. Thanks to the unique multilayer construction the device provides noise cancellation within the device, reducing ESL from nanohenry to picohenry levels. Using the unique balance between the Y-capacitors and the shielded multilayer structure the X2Y products offer superior decoupling and filtering. The X2Y device performs as a broadband filter enabling better EMC compliance for electrical equipment in a wide range of applications. BENEFITS Broadband Filter and Decoupler: X2Y is effective up to 10 GHz and frequencies beyond. By-pass: Unlike feedthrough capacitors, X2Y devices are in by-pass and only handle the noise current. Superior Balance: 2 closely matched Y-caps provide stable balance over time and temperature. Ultra-low Inductance: typical equivalent series inductance (ESL) to less than 50 picohenries. Ultra-low ESR: typical values of a few milli-ohms. Lower Component and Placement Costs: X2Y can eliminate inductors, ferrites, standard capacitors, resistors and surge devices normally combined to form filter networks in the past. Board Space Reduced: Whether on the PCB board or IC Package, X2Y components allow for design simplification resulting in a substantial reduction of board space needed. APPLICATIONS ing on DC motors Filtered connectors (airbag connectors, RJ-45 connectors) High speed data-line filtering Decoupling of supply-lines in high speed digital circuits Broadband filtering Typical Application Equivalent Circuit Configur at ion Lin e Cy Gr ound Cx Cy Line Fig.1 X2Y Multilayerfilter capacitor

4 X2Y Series

5 X2Y Series QUICK REFERENCE DATA DESCRIPTION Materials Rated Voltage Capacitance range (Y-capacitor) VALUE NP0, X7R, (Y5V, development) 10 V, 16 V, 25 V, 50 V, 100 V (IEC) 0603 series 10 pf to 100 nf 0805 series 10 pf to 470 nf 1206 series 47 nf to 2200 nf 1210 series 100 nf to 4700 nf 1812 series 100 nf to 1000 nf Tolerance on capacitance: 10%, 20%, - 20% / + 80% Test Voltage (DC) for 1 minute: 2.5 x U-rated Sectional specifications IEC , second edition Detailed specification Based on IEC Climatic category (IEC ) NP0 and X7R: 55/125/56, Y5V: 25/085/21 Available Capacitances & Voltage Ranges C (pf) NP0 X7R Y5V NP0 X7R Y5V X7R Y5V X7R Y5V X7R V 100V V V ,000 63V 15,000 25V 63V 100V 18,000 22,000 25V 39,000 16V 63V 100V 47,000 16V 56, ,000 10V 16V 100V 180,000 10V 16V 25V 63V 220,000 16V 270, ,000 25V 390,000 63V 470,000 10V 560, ,000 16V 25V 1,000,000 16V 2,200,000 16V 4,700,000

6 X2Y Series MECHANICAL DATA Physical dimensions Capacitor dimensions CASE T A L W SIZE MIN. MAX. MIN. MAX. C Dimensions in millimeters Dimensions in inches

7 X2Y Series ELECTRICAL CHARACTERISTICS FOR NP0 Class 1 capacitors; NP0 dielectric; NiSn terminations Unless otherwise stated all electrical values apply at an ambient temperature of 20 ±1 C, an atmospheric pressure of 86 to 106 kpa, and a relative humidity of 63 to 67%. DESCRIPTION Rated voltage UR (DC) 100 V Capacitance range 10 pf to 330 pf Tolerance on capacitance after 1000 hours: ±10% Tan Insulation resistance after 1 minute at U R (DC) Rins > 100 G Temperature coefficient 0 ±30 ppm/k VALUE Notes 1. Measured at 20 C, 1 V and 1 MHz, using a four-gauge method. SELECTION CHART FOR NP0 - Preferred types; other values on request Y capacitor X capacitor Size CAP Voltage rating CAP Voltage rating Thickness CTC Ordering Code (1),(2) pf 100 V 5 pf 200 V 0.60 mm X 0603 KR NP0 0BN pf 100 V 11 pf 200 V 0.60 mm X 0603 KR NP0 0BN pf 100 V 24 pf 200 V 0.60 mm X 0603 KR NP0 0BN pf 100 V 50 pf 200 V 0.60 mm X 0603 KR NP0 0BN pf 100 V 110 pf 200 V 0.60 mm X 0603 KR NP0 0BN pf 100 V 5 pf 200 V 0.85 mm X 0805 KR NP0 0BN pf 100 V 11 pf 200 V 0.85 mm X 0805 KR NP0 0BN pf 100 V 24 pf 200 V 0.85 mm X 0805 KR NP0 0BN pf 100 V 50 pf 200 V 0.85 mm X 0805 KR NP0 0BN pf 100 V 110 pf 200 V 0.85 mm X 0805 KR NP0 0BN pf 100 V 165 pf 200 V 0.85 mm X 0805 KR NP0 0BN 331 Notes 1. Ordering codes for preferred versions (10% tolerance, 180 mm reel). For other packing and tolerance see section Ordering Code. 2. For 12NC ordering codes see conversion table on page 9. Thickness classification and packing quantities for NP0 QUANTITY PER REEL THICKNESS CLASSIFICATION (mm) 8 mm TAPE WIDTH 180 mm; 7" 330 mm; 13" PAPER BLISTER PAPER BLISTER

8 X2Y Series ELECTRICAL CHARACTERISTICS FOR X7R Class 2 capacitors; X7R dielectric; NiSn terminations Unless otherwise stated all electrical values apply at an ambient temperature of 20 ±1 C, an atmospheric pressure of 86 to 106 kpa, and a relative humidity of 63 to 67%. DESCRIPTION VALUE Rated voltage UR (DC) 10 V, 16 V, 25 V, 50 V/63 V and 100 V Capacitance range 1 nf to 1 µf Tolerance on capacitance after 1000 hours: ±10%; 20% Tan ; note 1: 10V: 5% 16V: 3.5% 25V: 2.5% Insulation resistance after 1 minute at U R (DC) Rins x C > 500 seconds Maximum capacitance change as a function of temperature 15% Aging Typical 1% per time decade Notes 1. Measured at 20 C, 1 V and 1 khz, using a four-gauge method. Thickness classification and packing quantities for X7R THICKNESS CLASSIFICATION (mm) QUANTITY PER REEL 8 mm TAPE WIDTH 12 mm TAPE WIDTH 180 mm; 7" 330 mm; 13" 180 mm; 7" PAPER BLISTER PAPER BLISTER BLISTER

9 X2Y Series SELECTION CHART FOR X7R - Preferred types; other values on request Y capacitor X capacitor Size CAP Voltage rating CAP Voltage rating Thickness CTC Ordering Code (1),(2) nf 100 V 0.5 nf 200 V 0.60 mm X 0603 MR X7R 0BB 102 2,2 nf 100 V 1.1 nf 200 V 0.60 mm X 0603 MR X7R 0BB 222 4,7 nf 100 V 2.4 nf 200 V 0.60 mm X 0603 MR X7R 0BB nf 100 V 2.8 nf 200 V 0.60 mm X 0603 MR X7R 0BB nf 50 / 63 V 5 nf 100 V 0.60 mm X 0603 MR X7R 9BB nf 25 V 11 nf 50 V 0.60 mm X 0603 MR X7R 8BB nf 16 V 24 nf 25 V 0.60 mm X 0603 MR X7R 7BB nf 16 V 28 nf 25 V 0.60 mm X 0603 MR X7R 7BB nf 10 V 50 nf 16 V 0.60 mm X 0603 MR X7R 6BB ,7 nf 100 V 2.4 nf 200 V 0.85 mm X 0805 MR X7R 0BB nf 100 V 5 nf 200 V 0.85 mm X 0805 MR X7R 0BB nf 50 / 63 V 8 nf 100 V 0.85 mm X 0805 MR X7R 9BB nf 50 / 63 V 9 nf 100 V 0.85 mm X 0805 MR X7R 9BB nf 25 V 11 nf 50 V 0.85 mm X 0805 MR X7R 8BB nf 25 V 20 nf 50 V 0.85 mm X 0805 MR X7R 8BB nf 16 V 24 nf 25 V 0.85 mm X 0805 MR X7R 7BB nf 16 V 50 nf 25 V 0.85 mm X 0805 MR X7R 7BB nf 10 V 90 nf 16 V 0.85 mm X 0805 MR X7R 6BB nf 100 V 11 nf 200 V 1.20 mm X 1206 MK X7R 0BB nf 50 / 63 V 24 nf 100 V 1.20 mm X 1206 MK X7R 9BB nf 50 / 63 V 50 nf 100 V 1.20 mm X 1206 MK X7R 9BB nf 25 V 90 nf 50 V 1.20 mm X 1206 MK X7R 8BB nf 16 V 110 nf 25 V 1.20 mm X 1206 MK X7R 7BB nf 16 V 195 nf 25 V 1.20 mm X 1206 MK X7R 7BB nf 10 V 235 nf 16 V 1.20 mm X 1206 MK X7R 6BB nf 10 V 410 nf 16 V 1.20 mm X 1206 MK X7R 6BB nf 100 V 24 nf 200 V 1.20 mm X 1210 MK X7R 0BB nf 100 V 50 nf 200 V 1.60 mm X 1210 MK X7R 0BB nf 50 / 63 V 110 nf 100 V 1.60 mm X 1210 MK X7R 9BB nf 25 V 235 nf 50 V 1.60 mm X 1210 MK X7R 8BB nf 25 V 280 nf 50 V 1.60 mm X 1210 MK X7R 8BB nf 16 V 500 nf 25 V 1.60 mm X 1210 MK X7R 7BB nf 100 V 50 nf 200 V 1.20 mm X 1812 MK X7R 0BB nf 100 V 110 nf 200 V 1.60 mm X 1812 MK X7R 0BB nf 100 V 165 nf 200 V 1.90 mm X 1812 MK X7R 0BB nf 50 / 63 V 235 nf 100 V 1.60 mm X 1812 MK X7R 9BB nf 50 / 63 V 280 nf 100 V 1.90 mm X 1812 MK X7R 9BB nf 25 V 340 nf 50 V 1.20 mm X 1812 MK X7R 8BB nf 25 V 500 nf 50 V 1.60 mm X 1812 MK X7R 8BB 105 Notes 1. Ordering codes for preferred versions (20% tolerance, 180 mm reel). For other packing and tolerance see section Ordering Code. 2. For 12NC ordering codes see conversion table on page 9.

10 X2Y Series ELECTRICAL CHARACTERISTICS FOR Y5V Class 2 capacitors; Y5V dielectric; NiSn terminations Unless otherwise stated all electrical values apply at an ambient temperature of 20 ±1 C, an atmospheric pressure of 86 to 106 kpa, and a relative humidity of 63 to 67%. DESCRIPTION VALUE Rated voltage UR (DC) 16 V Capacitance range 100 nf to 4.7 µf Tolerance on capacitance after 1000 hours: -20% / +80% Tan ; note 1: 12.5% Insulation resistance after 1 minute at U R (DC) Rins x C > 500 seconds Maximum capacitance change as a function of temperature +30% to 80% Aging Typical 7% per time decade Notes 1. Measured at 20 C, 1 V and 1 khz, using a four-gauge method. SELECTION CHART FOR Y5V Y capacitor X capacitor Size CAP Voltage rating CAP Voltage rating Thickness CTC Ordering Code (1),(2) nf 16 V 110 nf 25 V 0.60 mm X 0603 ZR Y5V 7BB nf 16 V 235 nf 25 V 0.85 mm X 0805 ZR Y5V 7BB nf 16 V 1100 nf 25 V 1.20 mm X 1206 ZK Y5V 7BB nf 16 V 2350 nf 25 V 1.60 mm X 1812 ZK Y5V 7BB 475 Notes 1. Ordering codes for preferred versions (180 mm reel). For other packing and tolerance see section Ordering Code. 2. For 12NC ordering codes see conversion table on page 9. Thickness classification and packing quantities for Y5V THICKNESS CLASSIFICATION (mm) QUANTITY PER REEL 8 mm TAPE WIDTH 12 mm TAPE WIDTH 180 mm; 7" 330 mm; 13" 180 mm; 7" PAPER BLISTER PAPER BLISTER BLISTER

11 X2Y Series ORDERING INFORMATION Components may be ordered by using either a simple 15-digit clear text code or Phycomp s unique 12NC. Table 1 Conversion table: Clear text code - 12NC code NP0 and X7R size Capacitance Rated Capacitance Tolerance Voltage 12 NC TC SIZE Value CTC ORDERING CODE ORDERING CODE Y-CAP Y-CAP Y-CAP QUANTITY PER REEL NP pf 10% 100 V X 0603 KR NP0 0BN NP pf 10% 100 V X 0603 KR NP0 0BN NP pf 10% 100 V X 0603 KR NP0 0BN NP pf 10% 100 V X 0603 KR NP0 0BN NP pf 10% 100 V X 0603 KR NP0 0BN NP pf 10% 100 V X 0603 KR NP0 0BN NP pf 10% 100 V X 0805 KR NP0 0BN NP pf 10% 100 V X 0805 KR NP0 0BN NP pf 10% 100 V X 0805 KR NP0 0BN NP pf 10% 100 V X 0805 KR NP0 0BN NP pf 10% 100 V X 0805 KR NP0 0BN NP pf 10% 100 V X 0805 KR NP0 0BN NP pf 10% 100 V X 0805 KR NP0 0BN X7R nf 20% 100 V X 0603 MR X7R 0BB X7R ,2 nf 20% 100 V X 0603 MR X7R 0BB X7R ,7 nf 20% 100 V X 0603 MR X7R 0BB X7R ,6 nf 20% 100 V X 0603 MR X7R 0BB X7R nf 10% 50 / 63 V X 0603 KR X7R 9BB X7R nf 20% 50 / 63 V X 0603 MR X7R 9BB X7R nf 20% 25 V X 0603 MR X7R 8BB X7R nf 20% 16 V X 0603 MR X7R 7BB X7R nf 20% 16 V X 0603 MR X7R 7BB X7R nf 10% 10 V X 0603 KR X7R 6BB X7R nf 20% 10 V X 0603 MR X7R 6BB X7R ,7 nf 20% 100 V X 0805 MR X7R 0BB X7R nf 10% 100 V X 0805 KR X7R 0BB X7R nf 20% 100 V X 0805 MR X7R 0BB X7R nf 20% 50 / 63 V X 0805 MR X7R 9BB X7R nf 20% 50 / 63 V X 0805 MR X7R 9BB X7R nf 20% 25 V X 0805 MR X7R 8BB X7R nf 20% 25 V X 0805 MR X7R 8BB X7R nf 20% 16 V X 0805 MR X7R 7BB X7R nf 10% 16 V X 0805 KR X7R 7BB X7R nf 20% 16 V X 0805 MR X7R 7BB X7R nf 20% 10 V X 0805 MR X7R 6BB X7R nf 10% 100 V X 1206KK X7R 0BB X7R nf 20% 100 V X 1206 MK X7R 0BB X7R nf 10% 50 / 63 V X 1206 KK X7R 9BB X7R nf 20% 50 / 63 V X 1206 MK X7R 9BB X7R nf 10% 50 / 63 V X 1206 KK X7R 9BB X7R nf 20% 50 / 63 V X 1206 MK X7R 9BB X7R nf 10% 25 V X 1206 KK X7R 8BB X7R nf 20% 25 V X 1206 MK X7R 8BB X7R nf 20% 16 V X 1206 MK X7R 7BB X7R nf 20% 16 V X 1206 MK X7R 7BB X7R nf 10% 10 V X 1206 KK X7R 6BB X7R nf 20% 10 V X 1206 MK X7R 6BB X7R nf 20% 10 V X 1206 MK X7R 6BB

12 X2Y Series Continuation of table 1 Conversion table: Clear text code - 12NC code size X7R and Y5V TC SIZE Capacitance Value Capacitance Tolerance Rated Voltage Y-CAP Y-CAP Y-CAP CTC ORDERING CODE 12 NC ORDERING CODE QUANTITY PER REEL X7R nf 10% 100 V X 1210 KK X7R 0BB X7R nf 10% 50 / 63 V X 1210 KK X7R 9BB X7R nf 20% 50 / 63 V X 1210 MK X7R 9BB X7R nf 20% 25 V X 1210 MK X7R 8BB X7R nf 10% 25 V X 1210 KK X7R 8BB X7R nf 20% 25 V X 1210 MK X7R 8BB X7R nf 10% 16 V X 1210 KK X7R 7BB X7R nf 20% 16 V X 1210 MK X7R 7BB X7R nf 20% 100 V X 1812 MK X7R 0BB X7R nf 20% 100 V X 1812 MK X7R 0BB X7R nf 20% 100 V X 1812 MK X7R 0BB X7R nf 10% 50 / 63 V X 1812 KK X7R 9BB X7R nf 20% 50 / 63 V X 1812 MK X7R 9BB X7R nf 20% 50 / 63 V X 1812 MK X7R 9BB X7R nf 10% 25 V X 1812 KK X7R 8BB X7R nf 20% 25 V X 1812 MK X7R 8BB X7R nf 20% 25 V X 1812 MK X7R 8BB Y5V nf +20%/-80% 16 V X 0603 ZR Y5V 7BB Y5V nf +20%/-80% 16 V X 0805 ZR Y5V 7BB Y5V nf +20%/-80% 16 V X 1206 ZK Y5V 7BB Y5V nf +20%/-80% 16 V X 1812 ZK Y5V 7BB Ordering Code: Clear Text Code X2Y- Series Clear Text Codes (CTC) X 0805 K K X7R 9 B B 104 Code 1 Series Name X = X2Y series Code 2-5 Size Code EIA mm 0603 (1608M) 0805 (2012M) 1206 (3216M) 1210 (3225M) 1812 (4532M) Code 6 Capacitance tolerance K= 10% M= 20% Z= -20~+80% Code 7 Packing Style Code 8-10 TC Material NP0 X7R Y5V R= Paper Tape Reel 7 inch P= Paper Tape Reel 13 inch K= Embossed Plastic Tape Reel 7 inch F= Embossed Plastic Tape Reel 13 inch B= Bulk Bag Code 11 Rated Voltage 5=6.3V 6=10V 7=16V 8 =25V 9 =50V 0 =100V Code 12 Termination B=Ni-Barrier Code Capacitance Value (2 significant digits + number of zeros). The 3rd digit: Letter R is Decimal Point 0=1 1=10 2=10 2 3=10 3 4=10 4 5=10 5 6=10 6 Code 13 Process Code N= NP0 B = X7R and Y5V

13 X2Y Series RECOMMENDED DIMENSIONS OF SOLDER LANDS Reflow soldering CASE SIZE (EIA) FOOTPRINT DIMENSIONS (mm) Placement Accuracy (mm) A B C D E F Wave soldering CASE SIZE (EIA) FOOTPRINT DIMENSIONS (mm) Placement Accuracy (mm) A B C D E F

14 X2Y Series INSERTION LOSS CHARACTERISTICS Measurement setup X2Y series through measurement ICM X2Y fixture - Vector Network Analyzer: R&S ZVM 10 MHz - 20 GHz. - X2Y test fixture: ICM X2Y 10GHz series thru test fixture. - Measurement frequency range: 10 MHz - 10 GHz. - TRL calibration. - S-parameter files in Touchstone format available for simulation. Insertion loss curves (S21) Insertion Loss (S21) 0603 and 0805 X2Y series nF nF nF 100nF nF nF Frequency [MHz]

15 X2Y Series Insertion Loss (S21) 1206 and 1210 X2Y series nF nF uF nF nF Frequency [MHz] 0.0 Insertion Loss (S21) 1812 X2Y series nF 470nF nF nF Frequency [MHz]

16 X2Y Series TEST AND REQUIREMENTS IEC / CECC CLAUSE IEC TEST METHOD TEST PROCEDURE REQUIREMENTS 4.4 Mounting The capacitor may be mounted on printed-circuit boards or ceramic substrates by applying reflow soldering (including vapour phase soldering) or conductive adhesive 4.5 Visual inspection and dimension check Any applicable method using x 10 magnification Capacitance Class 1: 1000 pf; f = 1MHz 1000 pf; f = 1kHz NP0: measuring voltage 1V at 20 o C No visible damage In accordance with specification Within specified tolerance Class 2: For all capacitors f = 1 khz X7R: measuring voltage 1V at 20 o C Y5V: measuring voltage 1V at 25 o C Tan Class 1: 1000 pf; f = 1MHz 1000 pf; f = 1kHz NP0: measuring voltage 1V at 20 o C In accordance with specification Class 2: For all capacitors f = 1 khz X7R: measuring voltage 1V at 20 o C Y5V: measuring voltage 1V at 25 o C Insulation resistance At U R (DC) for 1 minute In accordance with specification Voltage proof 2.5 x U R for 1 minute No breakdown or flashover Temperature Between minimum and In accordance with characteristic maximum temperature 4.8 Adhesion A force of 5 N applied for 10 s to the line joining the terminations and in a plane parallel to the substrate 4.9 Bond strength of plating on end face Mounting in accordance with CECC , paragraph 4.4 Conditions: bending 1 mm at a rate of 1 mm/s, radius jig 340 mm specification No visible damage No visible damage C/C: class 1: within 10% class 2, X7R: within 10% class 2, Y5V: within 30%

17 X2Y Series IEC / CECC CLAUSE 4.10 Tb IEC TEST METHOD Resistance to soldering heat Resistance to leaching TEST PROCEDURE REQUIREMENTS Precondition: 120 to 150 o C for 1 minute; o C for s in a static solder bath o C for 30 1 s in a static solder bath 4.11 Ta Solderability Zero hour test, and test after storage (20 to 24 month) in original packing in normal atmosphere; Unmounted chips completely immersed for s in a solder bath at o C 4.12 Na Rapid change of temperature Preconditioning, class 2 only; NP0 / X7R: -55 to +125 o C; 5 cycles Y5V: -25 to +85 o C; 5 cycles The termination shall be well tinned after recovery. C/C: class 1: within 0.5% or 0.5pF whichever is greater class 2, X7R: -5% and 10% class 2, Y5V: -10% and 20% Using visual enlargement of x 10, dissolution of the termination shall not exceed 10% The termination shall be well tinned No visual damage after 48 hours recovery; C/C: class 1: within 1% or 1pF class 2, X7R: within 15% class 2, Y5V: within 20%

18 X2Y Series IEC / CECC CLAUSE IEC TEST METHOD 4.14 Ca Damp heat, Steady state TEST PROCEDURE REQUIREMENTS Initialisation: 48 hours after U R at 40 o C for 1 hour (for initial value measurement); hours at 40 o C; 90 to 95 % RH; U R applied No visual damage After recovery: Class 1: 1 to 2 hours Class 2: 24 hours C/C: class 1: within 2% or 1pF, whichever is greater class 2, X7R: within 15%, 20% class 2, Y5V: within +30 / -40% tan : class 1: 2 x specified value class 2, X7R: 7% class 2, Y5V: 15% 4.15 Endurance Preconditioning, class 2 only: 1000 hours at upper category temperature at: 1.5 x U R R ins : Class 1: 2500 M or R ins x C R 25 s, whichever is less Class 2: 1000 M or R ins x C R 25 s, whichever is less No visual damage after 24 hours recovery: C/C: class 1: within 2% or 1pF, whichever is greater class 2, X7R: within 20% class 2, Y5V: within +30 / -40% tan : class 1: 2 x specified value class 2, X7R: 7% class 2, Y5V: 15% R ins : Class 1: 4000 M or R ins x C R 40 s, whichever is less Class 2: 2000 M or R ins x C R 50 s, whichever is less

19 X2Y Series REVISION HISTORY Revision Date Change Description Notification Rev Sep Published on web Rev Jul Product range extended in all materials and sizes -Insertion loss measurements added Rev Jul Correction selection guide -Ordering info for a range of 10% versions added