GAME OF THRONES SERVICE AND OPERATION MANUAL

Transcription

1 GAME OF THRONES SERVICE AND OPERATION MANUAL WARNING MANUAL #780-50G4-00 GAME OF THRONES PRO #500-55G KICKERS - parts.service@sternpinball.com - facebook.com/sternpinball

2 TABLE OF CONTENTS 1. Setup and Moving SPIKE System and Node Guide Light, Switch, and Driver Reference Electronic Pinouts and Schematics Parts Reference

3 SETUP AND MOVING 1. SETUP AND MOVING 1.1 FIRST-TIME SETUP INSTRUCTIONS 2 2 TOOLS REQUIRED 5 5 CAUTION: AT LEAST TWO (2) PEOPLE ARE REQUIRED TO MOVE AND MANEUVER THE GAME. USE PROPER MOVING EQUIPMENT AND EXTREME CARE WHILE HANDLING. STERN PINBALL MACHINES WEIGH OVER 250LBS BOXED

4 SETUP AND MOVING FIRST-TIME SETUP CONTINUED CAUTION: PLAYFIELD GLASS IS MADE FROM HIGH-STRENGTH TEMPERED GLASS. TEMPERED GLASS IS SENSITIVE TO EXTREME TEMPERATURE SHIFTS AND CORNER NICKS, WHICH CAN CAUSE THE GLASS TO FAIL CATASTROPHI- CALLY. TAKE CARE TO STORE THE GLASS ON ON A SOFT, ROOM-TEMPERATURE SURFACE AND PREVENT THE CORNERS FROM BEING DAMAGED.

5 SETUP AND MOVING FIRST-TIME SETUP CONTINUED LOCATING, LEVELING, AND FINAL SETUP

6 SETUP AND MOVING 1.2 ADJUSTMENTS MENU STANDARD ADJUSTMENTS ID Adjustment Name Default Setting ID Adjustment Name Default Setting 38 39

7 SETUP AND MOVING FEATURE ADJUSTMENTS SPIKE PINBALL SOFTWARE UPDATE INSTRUCTIONS

8 SETUP AND MOVING 1.3 TRANSPORTING THE GAME 1. SECURE THE BACKBOX TOOLS REQUIRED STRAP (500LB OR GREATER) AN ASSISTANT HAND TRUCK CAUTION NEVER TRANSPORT THE GAME IN A MOVING VEHICLE WITH THE BACKBOX RAISED! TWO PEOPLE ARE REQUIRED TO REMOVE THE LEGS! 2. REMOVE THE LEGS AND STAND UP

9 SETUP AND MOVING 1.4 MAINTENANCE REGULAR MAINTENANCE - (MONTHLY/500 GAMES) OVERHAUL MAINTENANCE (5000 GAMES) COMMON PINBALL TOOLS 1.5 MAINTENANCE KITS 1.6 COMMON PARTS 9

10 SPIKE SYSTEM AND NODE GUIDE 2. SPIKE SYSTEM AND NODE GUIDE 2.1 SPIKE SYSTEM OVERVIEW 2.2 NODE BUS CABLING 2.3 SYSTEM POWER COIN-DOOR SAFETY INTERLOCK 2.4 SPIKE NODE ADDRESSES Address Figure SPIKE node addresses for nodes with 3-position DIP switches. Addresses 0-7 are not used by SPIKE nodes with 3-position DIP switches. Address Figure SPIKE node addresses for nodes with 4-position DIP 2.5 SPIKE NODE PROGRAMMING

11 SPIKE SYSTEM AND NODE GUIDE SPIKE SYSTEM AND NODE GUIDE CONTINUED 2.6 SPIKE SYSTEM TERMINOLOGY MULTI GENERAL ILLUMINATION LIGHTING SINGLE LIGHTS FLASHERS DRIVERS OPTOS INPUT/OUTPUT PROTECTIONS FUSES Fuse Rating (Amps) Type Part Number 2.7 COMMON SPIKE NODE BOARDS Description Type Part Number

12 IN C+ C- L+ L- R+ R- 1 1 D28 D29 D30 D13 48V 24V 9V 5V LINE OUT +48V S1 RESET GND SCL SDA RST LIGHT, SWITCH, AND DRIVER REFERENCE 3. LIGHT, SWITCH, AND DRIVER REFERENCE PLAYFIELD FRONT CN1 PRO NODE 8 CN14 CN3 NODE 8a BACKBOX POWER CN7 1 CN23 SD CARD NODE 9a SPIKE CPU CN24 BT1 BARY NETSTAT TxD RxD STATUS CN25 1 NODE 0 CN3 CN4 CN18 CN1 1 1 HEADPHONE CPU NODE 0 CN21 CN3 CN22 CN20 CN3 CN22 NODE 9 CN4 CN14 CN4 CN2 CN3 NODE 9b Node Bus Cable (RJ45) Serial Data Cable rr rrt arr 3.1 SPIKE NODE BOARDS CABINET CN13 CABINET NODE 1 NODE 10 CN2 CN3 CN14 CN4 NODE 10a PLAYFIELD REAR ID DIP Address Description Location Part Number 8a 9a 3.2 DRIVER REFERENCE ID Name Node Connector Ret. Pin Ret. Wire Voltage V+ Pin V+ Color Location Type Address Part Number

13 LIGHT, SWITCH, AND DRIVER REFERENCE DRIVER REFERENCE Figure

14 LIGHT, SWITCH, AND DRIVER REFERENCE DRIVER REFERENCE CONTINUED ID Name Node Connector Ret. Pin Ret. Wire Voltage V+ Pin V+ Color Location Type Address Part Number SWITCH REFERENCE ID Name Node Node Ext Conn. Input Pin Input Wire GND Pin Ground Wire Location Type Address Part Number

15 SWITCH REFERENCE CONTINUED ID Name Node Node Ext Conn. Input Pin LIGHT, SWITCH, AND DRIVER REFERENCE Input Wire GND Pin Ground Wire Location Type Address Part Number a 8 8a a a 8 8a 8 8a 8 8a

16 LIGHT, SWITCH, AND DRIVER REFERENCE SWITCH REFERENCE CONTINUED Figure

17 SWITCH REFERENCE CONTINUED ID Name Node Node Ext Conn. 3.4 LIGHT REFERENCE Input Pin LIGHT, SWITCH, AND DRIVER REFERENCE Input Wire GND Pin Ground Wire Location Type Address Part Number ID Name Node Node Ext. Conn. Ret. Pin Ret. Wire Src. Pin Src. Wire Location Type Light Color Address Part Number

18 LIGHT, SWITCH, AND DRIVER REFERENCE LIGHT REFERENCE CONTINUED ID Name Node Node Ext. Conn. Ret. Pin Ret. Wire Src. Pin Src. Wire Location Type Light Color Address Part Number a 3 9 9a 2 9 9a a a

19 LIGHT, SWITCH, AND DRIVER REFERENCE LIGHT REFERENCE CONTINUED Figure

20 LIGHT, SWITCH, AND DRIVER REFERENCE LIGHT REFERENCE CONTINUED ID Name Node Node Ext. Conn. Ret. Pin Ret. Wire Src. Pin Src. Wire Location Type Light Color Address Part Number a 9 9 9a 9 9 9a 9 9 9a 8 9 9a 9 9a 9 9 9a 8 9 9a 9 9a 9 9a 9 9a

21 LIGHT, SWITCH, AND DRIVER REFERENCE LIGHT REFERENCE CONTINUED ID Name Node Node Ext. Conn. Ret. Pin Ret. Wire Src. Pin Src. Wire Location Type Light Color Address Part Number

22 ELECTRONIC PINOUTS AND SCHEMATICS 4. ELECTRONIC PINOUTS AND SCHEMATICS 4.1 SPIKE CPU NODE DIRECT SWITCH MAPPING (CN25) ID Name Conn. Input Pin CONNECTORS Input Wire GND Pin Ground Wire Location Type Address Part Number 2 3 STATUS LEDS ID Connector Type Description COMPONENTS ID S2 Name LED ID Name Color Description 22

23 D28 D29 D30 D13 ELECTRONIC PINOUTS AND SCHEMATICS SPIKE CPU NODE 0 CONTINUED AUDIO PINOUTS ID Type Pin Description Minimum Impedance Max Power (RMS) POWER IN 1 1 9V 5V 48V 24V LINE OUT 1 1 C+ C- L+ L- R+ R- CN SPIKE CPU AMPLIFIED AUDIO OUT CN4 CN18 CN1 HEADPHONE 1 +48V CN23 GND +5V CN24 S1 RESET BT1 BATTERY RxD NETSTAT TxD STATUS DIP S2 USB CN21 CN20 GND SCL SDA RST SD CARD Figure SPIKE CPU Node connector detail. CN25 1 SPIKE NODE BUS CN3 CN22 COIN DOOR SERVICE SWITCH WIRING COUNTRY CODES (DIP S2) DIP S2 Country Figure Service switch wiring. Note that the Cabient Node must be present and CN10 and CN12 connected for the Coin Door Service Switches to function correctly. 23

24 ELECTRONIC PINOUTS AND SCHEMATICS 4.2 NODE 1 CABINET

25 ELECTRONIC PINOUTS AND SCHEMATICS 4.3 LOWER PLAYFIELD 48V 8-DRIVER PINOUT NODE CN3 CN Driver Node CN1 GREEN ORANGE BLACK NEUTRAL CN11 ON CN9 CN7 CN5 F1A 125V 7A TIME LAG CN4 CN2 CN14 CN12 CN10 CN8 CN6 F1B TOP GREEN ORANGE BLACK NEUTRAL ID Type Pin Description Wire Color ID Type Pin Description Wire Color

26 ELECTRONIC PINOUTS AND SCHEMATICS 4.4 MID PLAYFIELD 48V 4-DRIVER PINOUT NODE GREEN ORANGE BLACK NEUTRAL F1A CN Coil NODE CN1 CN11 CN9 CN7 CN5 ON 125V 7A TIME LAG CN CN2 CN14 CN13 CN16 CN15 F1B ID Type Pin Description Wire Color ID Type Pin Description Wire Color

27 ELECTRONIC PINOUTS AND SCHEMATICS 4.5 UPPER PLAYFIELD 48V 4-DRIVER PINOUT NODE GREEN ORANGE BLACK NEUTRAL F1A CN Coil NODE CN1 CN11 CN9 CN7 CN5 ON 125V 7A TIME LAG CN CN2 CN14 CN13 CN16 CN15 F1B ID Type Pin Description Wire Color ID Type Pin Description Wire Color

28 ELECTRONIC PINOUTS AND SCHEMATICS 4.6 SERIAL 16 LED BOARD 9A SERIAL 16 LED BOARD 9B ID Type Pin Description Wire Color ID Type Pin Description Wire Color

29 ELECTRONIC PINOUTS AND SCHEMATICS 4.8 SERIAL 16 LED BOARD 10A THROUGH OPTO RECIEVER ID Type Pin Description Wire Color ID Type Pin Description Wire Color MAIN POWER SUPPLY LED +V ADJ ID Type Pin Description Wire Color

30 ELECTRONIC PINOUTS AND SCHEMATICS 4.11 POWER DISTRIBUTION BOARD POWER PLUG WIRING CAUTION TO MAINTAIN SAFETY, GROUND WIRE FROM LINE FILTER IS TO BE MOUNTED FIRST ON GROUNDING STUD AND SECURED WITH NUT. ALL OTHER GROUNDS MAY THEN BE ATTACHED TO GROUNDING STUD. REPLACE ALL FUSES WITH CORRECT CURRENT RATINGS! NORTH AMERICA NEMA 5-15 PREWIRED OUTLET FUSE ID Type Pin Description Wire Color POWER SUPPLY POWER DIST. BILL VALIDATOR (USER INSTALLED OPTION) INTERNATIONAL POWER SUPPLY POWER DIST. LINE FUSES LINE FILTER GROUNDING STUD LINE FILTER GROUNDING STUD LINE CORDS Part Number L G N L G N ON/OFF SW ON/OFF SW FUSE Description Line Voltage (Region) Fuse Type Part Number Current

31 5. PARTS REFERENCE 5.1 PLAYFIELD RUBBER PARTS RUBBER O-RINGS PARTS REFERENCE ID Qty Size (ID) Size (OD) Durometer Color Part Number Figure Rubber o-ring part numbers and usage. ID: Inner less bounce, and more durable. ID Qty Description Color Part Number 2 Figure Other rubber part numbers and usage 5.2 RUBBER SIZE CHART Figure Rubber o-ring part locations Figure Rubber ring inner diameter sizing tool. Hold ring up to chart and read largest size on inside of ring. Dimensions are In-

32 PARTS REFERENCE 5.3 PLAYFIELD ASSEMBLIES, TOP Figure

33 PARTS REFERENCE 5.4 PLAYFIELD ASSEMBLIES, BOTTOM Figure

34 PARTS REFERENCE 5.5 BACKBOX PARTS Figure EXTERNAL SPEAKER PANEL PARTS G Figure INTERNAL

35 PARTS REFERENCE 5.7 CABINET PARTS

36 PARTS REFERENCE 5.8 FRONT MOLDING ASSEMBLY G BALL TROUGH ASSEMBLY F BALL SHOOTER ASSEMBLY

37 PARTS REFERENCE 5.11 FLIPPER ASSEMBLY, LEFT ND 5.12 FLIPPER ASSEMBLY, RIGHT ND Figure Figure

38 PARTS REFERENCE 5.13 AUTO LAUNCH ASSEMBLY BANK DROP TARGET ASSM W/ RIGHT ANGLE CONN

39 PARTS REFERENCE 5.15 KICKER ASSEMBLY ND PT SWITCH ASSEMBLY XX BALL DEFLECTOR ASSEMBLY S/U TARGET ASSEMBLY

40 PARTS REFERENCE 5.19 RIGHT RAMP ASSEMBLY LEFT RAMP ASSEMBLY

41 PARTS REFERENCE 5.21 POP BUMPER ASSEMBLY XX Part Number Description Qty

42 PARTS REFERENCE 5.22 DOWN POST ACTUATOR ACTUATOR & FULCRUM ASSY

43 PARTS REFERENCE 5.24 RAM ASSEMBLY ASSEMBLY, ELEC GAT, B.P. MT XX

44 PARTS REFERENCE 5.26 DRAGON SOLENOID ASSEM RIGHT WIREFORM ASSEMBLY RAPTOR TOY ASSEMBLY

45 PARTS REFERENCE 5.29 BALL GUIDE ASSEMBLY # THRONE ASSEMBLY BALL GUIDE ASSEMBLY #

46 PARTS REFERENCE 5.32 RAPTOR WING ASSEMBLY DRAGON ASSEMBLY DRAGON PRO ASSEMBLY

47 PARTS REFERENCE 5.35 BACK PANEL ASSEMBLY

48 SPECIFICATIONS 6. SPECIFICATIONS SPECIFICATIONS, MECHANICAL, GAME SETUP Imperial Metric SPECIFICATIONS, MECHANICAL, BOXED SPECIFICATIONS, ELECTRICAL SPECIFICATIONS, ENVIRONMENT 6.1 GAME DIMENSIONS

49 SPECIFICATIONS 6.2 WARRANTY STERN PINBALL INC LIMITED WARRANTY WARRANTY DISCLAIMER PARTS SUBSTITUTIONS FCC CLASS A SUBPART J COMPLIANCE NOTICE RF INTERFERENCE NOTICE COPYRIGHT AND INTELLECTUAL PROPERTY 6.3 WARNINGS, COMPLIANCE, AND LEGAL NOTICES PHOTOSENSITIVE SEIZURES HEALTH WARNING

50 1-800-KICKERS FACEBOOK.COM/STERNPINBALL GAME OF THRONES PRO MODEL G4-01 MANUAL PART G4-00 *780-50G4-00*