Installation Instructions
|
|
- Ophelia Wilkinson
- 5 years ago
- Views:
Transcription
1 Second Kit for the GrandSTAR Jukebox Kit # Purpose: These instructions outline the procedures to install a second 1000W into the GrandSTAR jukebox with the AV controller (shown) or the 4 Channel Preamp. Tools Required: 1/4" Nut Driver Parts Included in this Kit: Installation Instructions Item Part Number Description Qty Power Transformer Assembly Output Transformer Assembly Audio Cable Power Harness #8-32 x 3/8 screw #8-32 x 7/8 screw Assy. 1KW Adaptor Plate Caution Label Terminal Cover Pad Terminal Output Cover 1 12 Installation Instructions Figure 1 Page 1 of 6
2 Tips: Save the screws you remove for later use. Use a hand driver to avoid stripping the screw holes in the wood cabinet. Step-by-step Instructions: 1. Turn the Jukebox power off, and unplug the power cord from the wall outlet. 2. Remove the cover plate and the Audio output cover plate. See Figure 2. Cover Plate Audio Output Cover Plate Figure 2- Remove Cover Plates. 3. Remove the Transformer Cover Plate (bottom right side of cabinet). See Figure 3. Power Transformer Cover Plate. Page 2 of 6 Figure 3- Remove Transformer Cover Plate.
3 4. Install the (Item 7) onto the Adapter Plate (Item 8) using the four #8-32 x 3/8 screws (Item 5). 5. Install the amplifier and adapter plate assembly in the location shown in Figure 4. Use the screws that were removed in Step 2. Install and Adapter Plate Assembly Figure 4- Install and Adapter Plate 6. At the location for the Output Transformer Assembly (Item 2), install four of the #8-32 x 7/8 screws (Item 6) in the location shown in Figure 5. The screws will thread into T-nuts located on the back of the cabinet. Leave the screws loose enough to install the second output transformer assembly. Install four #8-32 x 7/8 screws Figure 5-Install screws for Output Transformer Assembly. Page 3 of 6
4 7. Place the output transformer assembly over the screws. Verify no wires or cables are being pinched between the transformer assembly and the back of the jukebox cabinet and tighten the screws. See Figure 6. Second Audio Output Transformer installed. Figure 6- Audio Output Transformer Assembly installed. 8. Route the wires of the Audio Output Transformer Assembly up thru the cable clamps and across to the 2 nd amplifier. Plug the 2 pin male connector with the green and black wires into the "SPEAKER OUTPUT CHANNEL 1 OR 3" header, and the 2 pin male connector with the brown and black wires into the "SPEAKER OUTPUT CHANNEL 2 OR 4" header of the amplifier. See Figure 7. Harness Routing 2 pin male connectors Figure 7 Connecting the Audio output wires. Page 4 of 6
5 9. Install the transformer assembly (Item 1) in the location shown in Figure 8. Use the screws that were removed in Step 2. Connect the five-pin male connector from the main power harness, into the five pin female connector of the Transformer Assembly. This five-pin connector on the main harness can be located in the right hand corner of the jukebox and is part of the main power harness. See Figure 8. Existing Power Harness with 5 position connector Transformer Assembly Figure 8- Transformer Assembly installed. 10. Connect the Power Harness (Item 4) to the 8 pin Power/Mute header on the amplifier. Route the harness toward the right corner and down thru the cable clamps. Plug the six pin male connector into the six pin female connector of the power transformer. Connect the 3 pin housing to the "Mute3 4"header of the AV Controller or the AMP RESET CH3/CH4 of the 4 Channel Preamp. See Figure 9. AV Controller or 4 Channel Pre-amp 8 pin Power/Mute header 3 pin housing to Mute3 4 or Amp reset CH3/CH4 6 pin male connector Figure 9- Routing the Power Harness. Page 5 of 6
6 11. Connect the 3 foot Audio Cable Assembly (Item 3) to the input jacks on the amplifier. Route the Audio cables toward the right side of the jukebox and down to the AV controller or the 4 channel Preamp using all available cable clamps. Connect the white audio cable to the "CH3" jack and the red audio cable to the "CH4" jack of the AV Controller or the white audio cable to the CH3 INV jack and the red audio cable to the "CH4" jack of the 4 channel Preamp. See Figure 10. Audio cables to Connect audio cables here. AV Controller Figure 10- Connecting Audio Cables. 12. Refer to Section 3 of your GrandSTAR Field Service Manual and the Network Setup Manual section 6.6 for VCU Setup information before connecting speakers to your Output Transformer. Attach the adhesive pads hidden by cover Caution Label Terminal Pad Cover. Figure 11- Installing the Terminal Output Cover 13. After making the speaker connections, remove the backing on the adhesive terminal pads (Item 10) and attach to the Terminal Pad Cover (Item 11) then mount the cover with the remaining two #8-32x7/8 screws. Apply the Caution Label (Item 9) as shown in Figure 11. Page 6 of 6
Installation Instructions
Installation Instructions NGX Dual Kit Kit #26679601 These instructions outline the procedures to install the Dual Kit in your NGX Jukebox. Tools Required 11/32 Nut Driver Parts Included with this Kit:
More informationCONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075
More informationKit# KOV ModBox IR REMOTE CONTROL KIT
ModBox Installation Instructions Kit# KOV-106-000-07 ModBox IR REMOTE CONTROL KIT INTRODUCTION: This kit adds IR Volume and Cancel Control to ModBox Jukeboxes. TOOLS REQUIRED: 1/4" nut driver, Philips
More information1. Mount the echo and tremolo control switches under the keyboard shelf, in a position convenient for the organist.
CONSOLE CONNECTOR KIT 8101 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models A-100, D-100, RT2, RT3 LESLIE Speaker Models 122, 122RV KIT CONTENT Console Connector Assembly 047357 Echo Control
More informationInstallation Instructions
Installation Instructions Kit Core Upgrade-EMB-B75B Without Modem Kit #22166905 These instructions outline the procedures to install the EMB-B75B motherboard into your existing Computer Core Chassis. There
More informationInstallation Instructions. Ecast Mojo B75B Motherboard Upgrade Kit Kit #
Installation Instructions Ecast Mojo B75B Motherboard Upgrade Kit Kit #26684501 This kit contains the parts and instruction to install the B75B Motherboard into your Ecast Mojo jukebox. Tools Required
More informationINSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 7830 FOR USE WITH: LESLIE Speaker Model 130 Various single and double channel organs INSTALLATION INSTRUCTIONS KIT CONTENT Console Connector 137283 Switch Assembly, Cable Assembly,
More informationInstallation Instructions
Installation Instructions IR REMOTE CONTROL KIT #22167904 INTRODUCTION: This kit adds IR Volume and Lighting Control to CD-100L or NSE-1 Jukeboxes that have a 2-Channel Preamplifier TOOLS REQUIRED: 1/4"
More informationInstallation Instructions. Rock-Ola Ecast B75B Motherboard Upgrade Kit Kit #
Installation Instructions Rock-Ola Ecast B75B Motherboard Upgrade Kit Kit #26683901 This kit will not support the Ecast Rock-Ola COIM Board. If your Rock-Ola core computer has the Ecast Rock-Ola COIM board
More informationService & Maintenance
Service & Maintenance Internal Amplifier External (Peavey) Amplifier Core & HDD Monitor UPS Dollar Bill Acceptor Coin Mechanism Cleaning Fans & Filter G1-1 Internal Amplifier Amplifier Removal 1. Disconnect
More informationInstallation Instructions
Installation Instructions Fan Kit #00 These instructions outline the procedures to install a Fan Kit in your MMCD-, MMCD-, and MMCD- Jukeboxes with a previously installed owe JUMP Kit. Tools equired /
More informationNOTE: Read the instructions completely through before beginning actual installation.
CONSOLE CONNECTOR KIT 7850 INSTALLATION INSTRUCTIONS FOR USE WITH: Various Two-channel Organs LESLIE Speaker Models 705, 705C, 720 KIT CONTENT Console Connector 138488 Switch Assembly, Cable Assembly,
More informationInstallation Instructions
Installation Instructions Ecast EQ to AMI hardware conversion KIT #26683701 This kit is for use in Ecast EQ jukeboxes. Tools Required #2 Phillips screw driver, #1 Phillips screw driver, Small flat blade
More informationInstallation Instructions
Kit #67006 - Conversion Kit TT Allegro MX to AMI Tools needed: Philips screw driver, / & 5/6 nut drivers, Drill Driver with / drill bit Parts included in this kit (see page for a picture of the parts in
More informationVoice Evacuation Control Panel Main Circuit Board Replacement Product Installation Document
Voice Evacuation Control Panel Main Circuit Board Replacement Product Installation Document Document 50795 Rev B 10/10/01 ECN 01-507 This Product Installation Document outlines the replacement of the Main
More informationInstallation Instructions. Ecast View B75B Motherboard Upgrade Kit Kit #
Ecast View B75B Motherboard Upgrade Kit Kit #26683801 This kit will not support the Ecast View COIM Board. If your View core computer has the Ecast View COIM board installed you must order the AMI Hardware
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More informationSection. Placing onlocation
Section Placing onlocation -LocationPower -RouterandotherCustomer Premise Equipment(CPE) -ConnectingSpeakers -IRRemoteControl -WiredRemoteControl -PagingMicrophone Floor Model C1-1 Location Power The DA-9000
More informationInstallation Instructions
Installation Instructions Tools Required Isopropyl Alcohol Dual DI Box for Applications Parts Included with this Kit KIT #26684202 Item Part Number Description Quantity 1 34109402 Dual DI Box Assy 1 2
More informationFC-25/50DA Main Circuit Board Replacement Product Installation Document
FC-25/50DA Main Circuit Board Replacement Product Installation Document Document 51875 Rev A 10/12/01 ECN 01-506 This Product Installation Document outlines the replacement of the Main Circuit Board for
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationREMOTE HEAD ADAPTER INSTALLATION GUIDE
REMOTE HEAD ADAPTER INSTALLATION GUIDE The Remote Head adapter is a valuable accessory for the Uniden BC-780, 785 and 796 scanners. It allows the scanner's control panel to be removed from the radio and
More informationSection. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1
Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.
More informationFITTING INSTRUCTIONS
& This option connects a GL3000 or GL3300 console as a channel expander to a second console with just one or two interconnecting cables. Kit Part No: GL3000-SL1 Single option to install SYS-LINK to one
More informationCREDIT CARD READER for ROWE CD100I CD100J Jukeboxes Installation Instructions Manual
CREDIT CARD READER for ROWE CD100I CD100J Jukeboxes Installation Instructions Manual Part No. This page intentionally left blank Table of Contents INTRODUCTION...5 Tools Required...5 Credit Card Reader
More informationValidator Update Instructions for Rowe BC1200 $1 - $20
Validator Update Instructions for Rowe BC1200 $1 - $20 Kit Overview The purpose of the kit is to replace the Rowe BA50 transport and stacker with a 120 volt Mars validator with a compact mask. The kit
More informationANIxx. Installation Manual.
ANIxx Installation Manual www.audac.eu Introduction WaveDynamics Dante audio network interface The ANIxx are Dante audio network interfaces for use with WaveDynamics supporting amplifiers, supporting two
More informationInstructions to Install Retrofit Kit RVMC 4/5000 Machine (MDB Only)
Instructions to Install Retrofit Kit RVMC 4/5000 Machine (MDB Only) **TURN POWER OFF OF MACHINE BEFORE INSTALLATION** READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION Retrofit Kit Contents PART NAME
More informationMCH WIRE HARNESS WITH QUICK DISCONNECT REPLACEMENT Initial Release 1/31/2013
1. Table of Contents 1. Table of Contents Page 1 2. Remove Failed MCH-103.2 Page 1 3. Install MCH-103.2 to MCH-102NW Page 2 4. Install NC3FX-HD to MCH-103.2 Page 3 5. Install MCH-103.2 Battery Terminal
More informationPhase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationMAIN PCB (The small one)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationAssembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.
Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.
More informationPandora Assembly Instructions With Diamond Systems PC/104 CPUs (Athena, Elektra and Prometheus) November, 2006
Pandora Assembly Instructions With Diamond Systems PC/104 CPUs (Athena, Elektra and Prometheus) November, 2006 Diamond Systems Corp. (650) 810-2500 www.diamondsystems.com This document describes how to
More informationHow To Install: G2500 EMV Upgrade Kit
How To Install: G2500 EMV Upgrade Kit Tools Needed: Phillips Screw Driver Wire Cutter - Begin by verifying the contents of the kit Kit includes: - EMV Card reader (with ground and data cable) - Card reader
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationL-80 SERIES HOME & COMMERCIAL HIGH-TECH ENTERTAINMENT CENTER DIAGNOSTIC ADDENDUM
111 Canfield Avenue Randolph, New Jersey 07869 1-800-LANDICE FAX 973-927-0630 L-80 SERIES HOME & COMMERCIAL HIGH-TECH ENTERTAINMENT CENTER DIAGSTIC ADDENDUM High-Tech Entertainment Center Explosion Part
More informationLandmark Upgrade Kit Installation Instructions
Landmark Upgrade Kit Installation Instructions REMOVING THE LANDMARK BOARD 1 REMOVE POWER FROM UNIT. 2 Disconnect ALL board connections by removing the associated blue blocks (see Figure 1). Include the
More informationRoyal RVV-500 (B) Retrofit Kit
Optipay BV/RC/CC into a Non-Fascia Vending Machine This document contains information for installing and configuring the JCM Optipay DBV-01 Bill Validator, RC-10 Bill Recycler and A-66 Coin Changer into
More informationUSBCNC-SW USB Disk Key reader for CNC Controls Machine Mount instructions for Universal Switcher Version
USBCNC-SW USB Disk Key reader for CNC Controls Machine Mount instructions for Universal Switcher Version 2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla Street Chatsworth, CA 91311
More informationUSBCNC USB Disk Key reader for CNC Controls Machine Mount instructions
USBCNC USB Disk Key reader for CNC Controls Machine Mount instructions 2008-2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 www.calmotion.com Introduction This
More information21 TRACK MAINTENANCE GUIDE
Mountain Engineering II, Inc. 21 TRACK MAINTENANCE GUIDE 1233 Sherman Drive, Longmont, CO 80501-6133 303-651-0277 303-651-6371 (fax) www.mountainengineering.com Table of contents Table of contents...2
More informationE2460GS Oscilloscope Upgrade Kit
Installation Instructions for E2460GS Oscilloscope Upgrade Kit Agilent 1670G-Series Logic Analyzers This kit upgrades either the Agilent Technologies 1670G, Agilent 1671G, Agilent 1672G, or the Agilent
More informationINSTRUCTIONS FOR THE INSTALLATION OF THE INFINITY "L" DISPLAY HOOD (INTO PREVIOUSLY INSTALLED INFINITY "L" SYSTEMS)
Doc. 6001025 Rev B INSTRUCTIONS FOR THE INSTALLATION OF THE INFINITY "L" DISPLAY HOOD (INTO PREVIOUSLY INSTALLED INFINITY "L" SYSTEMS) Rev. B Doc. 6001025 Page 1 of 13 IMPORTANT NOTICE This document covers
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS MicroComm DXI. Intent & Scope This document describes the installation procedure for the IMS-30 Intercom Master Station and the MAI-420 or MAI-20 Master Audio Interface. The earliest
More informationBasketball Shot Clock Set LX2180 Manual
Basketball Shot Clock Set LX2180 Manual 72 Industrial Boulevard Wrightsville, GA 31096 Phone: (800) 445-7843 Fax: (800) 864-0212 www.electro-mech.com LX2180 Revision 5 February 8, 2013 Table of Contents
More informationAssembly Instructions Triton Enclosure for Poseidon With Data Acquisition November, 2007 V0.9 DSC Document #
Assembly Instructions Triton Enclosure for Poseidon With Data Acquisition November, 2007 V0.9 DSC Document #7521002 Diamond Systems Corp. (650) 810-2500 www.diamondsystems.com This document describes how
More informationInstructions for installing your QuiltCam on your Gammill quilt machine.
Instructions for installing your QuiltCam on your Gammill quilt machine. The items include with your QuiltCam Items included in all packages: QuiltCam Control Box, See Figure 1 Power Supply, Figure 2 Video
More informationRF Remote Control Kit
RF Remote Control Kit The Rock-Ola RF Remote control operates via radio and therefore does not need to see the jukebox or even be in the same room. There are over 1000 channels available for reliable operation.
More information9600 PCI EPP Keypad and
9600 PCI EPP Keypad and Card Reader Upgrade TDN 07103-08200 Feb 11, 2011 This upgrade requires software updates for both Canada and the US. Refer to page 6 in this manual and the Triton web site for the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS MicroComm DXI MAI-425 Master Audio Interface. Intent & Scope This document describes the installation procedure for the MAI-425 Master Audio Interface. The earliest version of
More informationThe basic product comes with the IRS5 control board, 3 internal cables, 1 external cable with a 5 volt adapter and a mounting bracket with hardware.
Please read these instructions and watch the Installation Video before you proceed with the installation of the PC-IRS5-01. Installation Video: http://youtu.be/os98e32vhb4 The PC-IRS5-01 Infrared Receiver
More informationLED Lighting Kit For Elara NanoEdge Fixed Frame. Installation Guide. Attention: Read this guide before assembling your screen.
LED Lighting Kit For Elara NanoEdge Fixed Frame Installation Guide Attention: Read this guide before assembling your screen. INTRODUCTION GETTING STARTED WARNING - Sharp Edges This product may contain
More informationCoin Acceptors, Inc. Installation Instructions for the 4.3 Touch Screen Display
Coin Acceptors, Inc. Installation Instructions for the 4.3 Touch Screen Display Kit # 410930 and 410930-1 DN3800 and DN5800 Publication 928412 1 Hand Drill Utility Knife Step Ladder 5/8 Drill Bit Tools
More informationCAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly
CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the
More informationDelta T Dew Heater for CDK
Delta T Dew Heater for CDK Delta T Dew Heater for CDK12.5 (125902) Your CDK 12.5 Delta T Dew Heater includes the following: QTY 1 Delta T control box w/ mounting bracket attached 1 2.5Amp AC adapter 2
More informationFB2550 to FB2558 Upgrade Kit Revision /18
Bulletin 51438 FB2550 to FB2558 Upgrade Kit Revision 1.0 08/18 Desktop, Rack Mount & Panel Mount Enclosures Instructions (34214 kit) 1. Shut down the FB2550 using the F5 key. 2. Once properly shut down,
More informationAg Leader Technology Insight. Direct Command Installation Spra-Coupe 7000 Series
Note: Indented items indicate parts included in an assembly listed above. Part Name / Description Part Number Quantity Direct Command Spra-Coupe 7000 Kit 4100531 1 Liquid Product Control Module 4000394
More informationDaNI Robot Camera. User Guide V0512
DaNI Robot Camera User Guide 60018 V0512 Materials Included Camera (includes hardware that will not be used) Modem (with power supply that will not be used) Power converter 6" Velcro strip Adhesive tab
More informationASSET LGA1366 Top-side Probe
ASSET LGA1366 Top-side Probe (Manual version 1.1) For gaining test access to the debug port of Intel processors that are designed for use in LGA1366 Sockets (Socket B). These include the Intel Core i7
More informationIon Memory Upgrade. Visit the AMI Entertainment Web site PM
Ion Memory Upgrade Visit the AMI Entertainment Web site http://www.meritgames.com PM0672-04 COPYRIGHT 2011 AMI ENTERTAINMENT NETWORK, INC. Ion Memory Upgrade CONTENTS: QTY PART NUMBER DESCRIPTION 1 EC0146-06
More informationINSTALLATION INSTRUCTIONS. This document describes the installation procedures for the TMM-441 Touchscreen Master Module.
INSTALLATION INSTRUCTIONS MicroComm DXI Intent & Scope This document describes the installation procedures for the. 2 Description The TMM-44 is a desktop unit consisting of a speaker, a gooseneck electret
More informationBL-FLOWSTN-P FlowStation Module Installation Guide
Introduction Baseline s FlowStation is available as an add-on module that is installed inside a pedestal enclosure with a BaseStation 3200 irrigation controller. The FlowStation module comes with a 5-port
More informationEmbedded Automation, Inc. Suite #104, th Street Surrey, BC V3W 1H8 Phone: (604) Fax: (604)
Embedded Automation, Inc. Suite #104, 7485 130 th Street Surrey, BC V3W 1H8 Phone: (604) 596-4999 Fax: (604) 596-4933 www.embeddedautomation.com User Manual Page 1 Table of Contents REVISION HISTORY...
More informationDevices that must be present to control the Wi-Fi Hub.
HV1600 Wi-Fi Hub Instruction Manual (Upgrade Fan Kit). For this Wi-Fi Hub Upgrade Kit to be compatible with your HV1600 fan it must meet the following criteria. The HV1600 serial number must be SN: 12244
More informationEncore XT Manual Gun Upgrade Kit
Instruction Sheet P/N 1600823-01 Encore XT Manual Gun Upgrade Kit 1600834 Introduction Follow these instructions to upgrade your Encore manual spray gun to the improved design of the Encore XT spray gun.
More informationRaven Adapter Harness
Note: Indented items indicate parts included in an assembly listed above Quantity by System Part Name/Description Part Number With Switch Box With Built-in Switches Raven Harness Adapter Kit 4100504 1
More informationView Wall Interface. Dynamic Glass INSTALLATION GUIDE. Description. System Requirements. Installation Overview
Description The solution is a compact, wall-mounted interface used for monitoring and changing the tint levels of View Dynamic Glass. The product leverages 802.11-based Wi-Fi technology for connectivity
More informationComputer Assembly (Installing Mother Board & CPU)
Computer Assembly (Installing Mother Board & CPU) IT@SCHOOL HARDWARE TEAM Biju Thiruvananthapuram Sree Kumar Kottarakkara Shamsudeen Attingal Pradeep Mattara Wandoor Pre-Installation Precaution Mother
More informationService Parts Diagrams. For Model: 2000i-DVS with the NEC VT465 Projector 2000i-DVS with the NEC VT470 Projector
Service Parts Diagrams For Model: 000i-DVS with the NEC VT65 Projector 000i-DVS with the NEC VT70 Projector Service Parts Diagrams for the Rear Projection SMART Board 000i-DVS Interactive Whiteboard Identifying
More informationCustom O2+ODAC Soldering Instructions
Custom O2+ODAC Soldering Instructions Preparations The following components should be omitted during basic assembly: R1, R2 D2, D6 BT2 The following components should be omitted based on required customization:
More informationModular Table Power System Installation for Runner Non-folding Plug and Play Tables
Modular Table Power System Installation for Runner Non-folding Plug and Play Tables Topic General Safety Warnings Ganging Hardware Electrical Circuits Table of Contents Page End-to-End (Page 4) End-and-Back
More informationService Parts Diagrams
Service Parts Diagrams For Model: 000i-DVX with the NEC MT00 Projector 000i-DVX with the NEC VT0 Projector 000i-DVX with the NEC VT70 Projector Service Parts Diagrams for the Rear Projection SMART Board
More informationFCB1010 Phantom Power Adaptor
FCB1010 Phantom Power Adaptor The Behringer FCB1010 pedal is normally powered by an external cable that plugs into a standard 120 volt 3-prong wall receptacle. While this works fine, it does require a
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. MINIGRABBER TEST CLIP WITH BANANA JACK Banana Jack built into plunger. RATING:
More informationUpgrade Instructions. P/N Revision A. October Printer Terminal Holder * *
Upgrade Instructions P/N 96-08-0 Revision A October 000 480 Printer Terminal Holder P/N 96-08-0 Revision A *96080* Instructions This terminal holder connects the INTERMEC R 600 Series and 700 Series Computers
More informationCU-8R Installation Instructions
CU-8R Installation Instructions I. Components Model CU-8R is shipped with the following components: QTY Item 1 Stainless Steel Enclosure 2 Lexan Panels 18 Nuts 1 Wall Mount Style Phone with RJ-11 Cable
More informationPoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.
ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power
More informationArrakis Systems 6604 Powell Street / Loveland, Colorado 80538
Arrakis Systems 6604 Powell Street / Loveland, Colorado 80538 Input and Output wiring for the 150sc, 500sc, 2000sc and 2100sc audio consoles. A Input Channel Wiring (Back of Console) 6. Left Input 5. Left
More informationICM-400 Series Intercom Stations
ICM00 Series Intercom Stations. Intent & Scope This document describes the installation procedure for the ICM00 series intercom stations. The ICM00 series intercom stations include intercom stations types
More informationTim Hortons EI30 Ethernet Interface Circuit Board
Tim Hortons EI30 Ethernet Interface Circuit Board INSTALLATION INSTRUCTIONS Replacing the Precidia Unit with the HME EI30 Thank you for purchasing the EI30 Ethernet Interface. The EI30 enables the System
More informationLMH-100 Installation Instructions
Ritron, Inc. 505 West Carmel Drive Carmel, IN 46032 P.O. Box 1998 Carmel, IN 46082 Ph: 317-846-1201 Fax: 317-846-4978 Email: ritron@ritron.com web: www.ritron.com LMH-100 Installation Instructions Ritron
More informationDigital Keypad Introduction
K2 Digital Keypad Introduction The K02 uses the latest microprocessor technology to operate door strikes and security systems that require a momentary (timed) or latching dry contact closure. All programming
More informationCONEC Industrial Ethernet Circular Sealed RJ45 Connector System consists of a RJ45 Plug Kit, a Receptacle Kit and a Protective Cover Assembly.
Revised Sept-28-2009 Sealed Industrial Ethernet Circular IP67 Cat. 5e RJ45 Connector System Instructions CONEC Industrial Ethernet Circular Sealed RJ45 Connector System consists of a RJ45 Plug Kit, a Kit
More informationService Parts Diagrams. For Model: 2000i-DVX with the the NEC VT595 MT1060 Projector
Service Parts Diagrams For Model: 000i-DVX with the the NEC VT595 MT060 Projector 000i-DVX Serial numbers with 000i-DVX-R-5000 the NEC VT560 Projector and higher 000i-DVX Serial numbers with 000i-DVX-R-0000
More informationQuick Installation Guide
Nextiva HDR 1800 High-Definition Receiver Version 1.0 Quick Installation Guide All users should read the Nextiva HDR 1800 User Guide for complete details on installation, usage and functionality. This
More informationMK-MANTA I. Model MK-Manta I Core Drill Owner s Manual Parts List & Operating Instructions. serial number CAUTION
please record the serial number of your drill in this block. serial number For your one (1) year warranty to be effective, complete the warranty card (include the serial number) and mail it in as soon
More informationIndustrial IP67-rated 4-Port 10/100/1000T at PoE + 2-Port 10/100/1000T. Managed Ethernet Switch. (-40~75 degrees C) IGS-604HPT-RJ
Industrial IP67-rated 4-Port 10/100/1000T 802.3at PoE + 2-Port 10/100/1000T Managed Ethernet Switch (-40~75 degrees C) IGS-604HPT-RJ Quick Installation Guide Table of Contents 1. Package Contents... 3
More informationReachFree ID Installation Instructions for Wash Select II. Unitec
ReachFree ID Installation Instructions for Wash Select II Unitec www.startwithunitec.com Proprietary Information and Materials of Unitec Inc. Such proprietary information and materials may not be disclosed
More informationFloppy Disk To USB. Converter Installation and. Operation Manual
Floppy Disk To USB Converter Installation and Operation Manual Kit Price $125.00 Plus Shipping Why Should I Change My Floppy Drive To A USB Drive? You won't ever need floppies anymore and yet you'll be
More informationPlasma Panel Replacement Guide DU-42PX12X
Plasma Panel Replacement Guide DU-42PX12X Panel Replacement: At this point, the panel has been determined to be defective and replacement is necessary. Upon receiving the replacement panel, it must be
More informationSouthwest Community Education. Computer and AV Setup Guide
Southwest Community Education Computer and AV Setup Guide Authored by Carl Schroedl 8/19/2009 Contents Before You Start... 3 About this Guide... 3 Getting Help... 3 AV Kit Inventory... 4 Equipment Setup...
More informationEASTERN LABS. Instructions Model RM /25/2007. Operation. Junction Box Assembly. Different Types of Switch Installations
EASTERN LABS Instructions Model RM-1205 04/25/2007 Operation Junction Box Assembly Different Types of Switch Installations Counter Mounting Suggestions Operation Total Counter Mix Counter Thru counter
More informationHDMI Upgrade for the Showcase DVD
THE LEADER IN AUDIO ENGINEERING for the Showcase DVD INSTALLATION AND SETUP GUIDE Getting Started THERE ARE NO USER- SERVICEABLE PARTS INSIDE ANY KRELL PRODUCT. Krell authorizes this HDMI upgrade to the
More informationStar Trac Fitness E-ST 5090 Stepper. Install Guide
Star Trac Fitness E-ST 5090 Stepper Install Guide STAR TRAC E-ST STEPPER Install Guide E-ST 5090 E Series Stepper ASSEMBLY AND SETUP The following parts are included with the base STAR TRAC E-ST STEPPER:
More informationREMOVE COVERS. 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer.
REMOVE COVERS 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer. 3. Fully open the Top Cover. 4. Release the tab on the right
More informationMegatouch FORCE Monitor Chassis Board Replacement
Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis
More informationWall Mount Kit for Touch Panel Controller. Installation Guide
Wall Mount Kit for Touch Panel Controller Installation Guide Table of Contents Getting Started... 1 SKUs Used... 2 Connections... 3 Powering a Touch Panel Controller... 3 Communication Connections... 3
More informationMAIN PCB (The small one with the square cut out from one side)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationFlying Tickets FT Operation & Service Manual. Version 1.0. * Read this manual before use
Flying Tickets FT-65-1001 Operation & Service Manual Version 1.0 * Read this manual before use Flying Ticket Manual V1.0 General Remark If you encounter any difficulties or if you need support on how to
More information