StringPin Pinsetter with Electrical Requirements

Size: px

Start display at page:

Download "StringPin Pinsetter with Electrical Requirements"

Gerard Logan
5 years ago
Views:

1 Pre-Installation Manual StringPin Pinsetter with Electrical Requirements July 2018 /

2 Brunswick StringPin Pinsetter Electrical Requirements Pre-Installation Manual July 2018 by the Brunswick Bowling Products. All rights reserved. Manual Part No Notice: If available, updates to this manual can be found on-line at Confidential proprietary information. All information contained in this document is subject to change without notice. Brunswick Bowling Products 525 West Laketon Avenue Muskegon, MI U.S.A StringPin Pinsetter Electrical Requirements

3 CONTENTS Introduction...6 Interference Information...6 Surge Suppression...6 Wiring Requirements...6 Wiring Method...6 Grounding...6 Pinsetter Guarding Options...7 European Union Countries...7 Non-European Union Countries...8 Electrical Overview...9 Electrical Sub-Panel Specifications...9 Sub-panel and Surge Suppressor Installation...11 Three Phase Power Panel...11 Single Phase Power Panel...12 Selecting a Surge Suppressor...13 StringPin Pinsetter Overview (Rear Mount Controller)...14 StringPin Pinsetter Overview (Front Mount Controller)...16 Power Outlet Information...18 StringPin Controller...18 StringPin Controller (Rear Mount)...19 StringPin Controller (Front Mount)...20 StringPin Controller Wiring...21 Internal - UL Version...21 Internal - CE Version...22 Input Power - Wye Configuration (380V)...23 Input Power - Delta Configuration (208V/230V)...24 Input Power - With Phase Converter...25 StringPin Pinsetter Electrical Requirements 3

4 IMPORTANT! The information in this manual is a guide. All local codes will need to be considered during the design and building process. NOTE: Dimensions in this Guide have metric conversions and are expressed in meters to the third decimal point for any dimension over a meter and are expressed in millimeters for any dimension under a meter. NOTE: Designated specifications within the planning guide are required for customers within the European Union in order to comply with local, national and European health and safety regulations. Failure to follow these specifications will render the CE Declaration of Conformity and associated warranty null and void. 4 StringPin Pinsetter Electrical Requirements

5 NOTICE TO CUSTOMERS IN THE EUROPEAN UNION! Brunswick s Declaration of Conformity to the Machinery Directive is provided subject to adherence to the specifications provided in this Guide. NOTE: Specifications with the designated CE indicator are required for conformity with the European Union s Machinery Directive and are a prerequisite to Brunswick s provisioning of the Declaration of Conformity and related warranty. Customers who elect to deviate from the designated specifications forfeit Brunswick s warranty in relation to compliance to the Machinery Directive and they take full responsibility for complying with European,national, regional and local regulations. Customers who elect to take these deviations are advised to consult with local worker s health and safety experts before construction. StringPin Pinsetter Electrical Requirements 5

6 INTRODUCTION This document contains the information necessary for the preparation of a site conforming to Brunswick specifications. It is very important the site complies with the requirements specified in the following pages. Any deviations from these specifications could cause problems to your equipment that may be difficult to detect and/or correct. INTERFERENCE INFORMATION CAUTION! This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the installation manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. SURGE SUPPRESSION A transient voltage suppressor (TVSS) is NOT supplied with the pinsetter system, but is suggested. The installation of this TVSS is the responsibility of the customer through a licensed electrician. The TVSS will be located at the pinsetter sub-panel that supplies the electronics. This TVSS is designed for the most demanding environment and incorporates multistage filtration in its design. The Sine Wave tracking series is engineered to remove the more complex disturbances found in the electrical environment, in particular, high and low voltage ringing transients and harmonic activity. NOTE: The surge suppressor wires should be as short as possible, with no coiling when installed on the pinsetter sub-panel. The TVSS is provided with a plastic coupler to insulate the unit from the sub-panel. WIRING REQUIREMENTS Wiring Method The pinsetter control boxes require a permanent wiring connection to the AC supply using rigid conduit. Use of flexible cord for connection to these boxes is not sufficient. Grounding The pinsetter must be connected to a grounded, metal, permanent wiring system; or an equipmentgrounding conductor must be run with the circuit conductors and connected to the equipmentgrounding terminal on the control box. 6 StringPin Pinsetter Electrical Requirements

7 PINSETTER GUARDING OPTIONS European Union Countries LOCAL GUARDING (CE Certified) - Required for customers in the European Union A. 360 degree security perimeter B. Rear Machine/Ball Accelerator Guards C. Front masking unit panel (required) D. Rear Machine Guards E. Top/Motor Drive Guards F. Rear Pinfall Guards G. Side Pinfall Guards H. Ball Accelerator Guard J. Front Table Guard (not shown) K. Pin Station Guard (not shown) StringPin Pinsetter Electrical Requirements 7

8 Non-European Union Countries Brunswick strongly encourages customers to consider upgrading to Brunswick s Advanced Guarding (CE Certified) system. UL GUARDING (UL Certified) Required for customers located outside the European Union A. B. C. D. Rear Machine Guards Front masking unit panel (required) Top/Motor Drive Guards Pin Station Guards LOCAL GUARDING (CE Certified) Required for customers in the European Union & residential installations A. B. C. D. E. F. G. H. J. K degree security perimeter Rear Machine/Ball Accelerator Guards Front masking unit panel (required) Rear Machine Guards Top/Motor Drive Guards Rear Pinfall Guards Side Pinfall Guards Ball Accelerator Guard Front Table Guard (not shown) Pin Station Guard (not shown) StringPin Pinsetter Electrical Requirements

9 Electrical Overview ELECTRICAL SUB-PANEL SPECIFICATIONS IMPORTANT!: All sub-panels and wiring MUST comply with local and national electrical codes. Pinsetter Sub-panel The Pinsetter sub-panel used to power the StringPin pinsetters and other Brunswick equipment must be powered directly from the primary main service sub-panel or transformer. Non-Brunswick equipment including electronic video games, arc welders, HVAC, compressors, etc., cannot share this sub-panel. Scoring Sub-panel The scoring sub-panel must be powered from the main service sub-panel or transformer. Non-Brunswick equipment including electronic video games, arc welders, HVAC, compressors, etc., cannot share this sub-panel. The ONLY type of equipment to be installed in the sub-panels: Pinsetter Sub-panel StringPin Pinsetter Ball Lift Tel-E-Foul Lane Machine Ball Polisher Lightworx Lanescape Video Masking Unit Ticket Depot Scoring Sub-panel Scoring Computer Peripheral Controllers Sync Table Power Supply 32 /43 /49 /55 Overhead Monitors Display Controller HD Video Distribution Center Server Computer Client Computer Automated - Pinball Wizard Digital Signage WARNING! Any Non-Brunswick equipment circuits located in these subpanels will VOID ALL WARRANTY. This includes electronic video games, arc welders, HVAC, compressors, etc. StringPin Pinsetter Electrical Requirements 9

10 PINSETTER SUBPANEL SURGE SUPPRESSOR KEEP WIRES AS SHORT AND STRAIGHT AS POSSIBLE MAIN SERVICE SUBPANEL NEUTRAL BUSS GROUND BUSS 3 PHASE INCOMING 3-PHASE FROM SERVICE MAIN SUBPANEL SCORING SUBPANEL NEUTRAL BUSS NEUTRAL BUSS SURGE SUPPRESSOR KEEP WIRES AS SHORT AND STRAIGHT AS POSSIBLE GROUND BUSS GROUND BUSS NEUTRAL CONDUCTOR EARTH GROUND CONDUCTOR GROUND BUSS RECEPTACLE NEUTRAL EQUIPMENT GROUND CONDUCTOR PHASE Figure 1 IMPORTANT!: Split house centers with multiple sub-panels require a single source of power and ground from main service. 10 StringPin Pinsetter Electrical Requirements

11 SUB-PANEL AND SURGE SUPPRESSOR INSTALLATION Three Phase Power Panel Figure 2 StringPin Pinsetter Electrical Requirements 11

12 Single Phase Power Panel CAUTION! THE PHASE CONDUCTOR MUST BE INSTALLED ON A SINGLE PHASE CIRCUIT BREAKER. THE SCORING OVERHEAD CIRCUIT BREAKERS ARE PREFER. POWER PANEL INSULATING SPACER MUST BE INSTALLED SURGE SUPPRESSOR KEEP WIRES AS SHORT AND STRAIGHT AS POSSIBLE NEUTRAL BUSS SINGLE PHASE CIRCUIT BREAKER GROUND BUSS RECEPTACLE FEMALE CAPS MAIN SERVICE SUBPANEL GROUND BUSS 1-PHASE GROUND CONDUCTOR SINGLE PHASE/HOT NEUTRAL CONDUCTOR EARTH GROUND ELECTRODE OR EQUIVALENT CLASS "A" - 5 OHMS OR LESS Figure 3 12 StringPin Pinsetter Electrical Requirements

13 SELECTING A SURGE SUPPRESSOR A flow chart diagram is shown below to assist you in identifying which surge suppressor is needed. Model Voltage/Phase Wye/Delta No. of Wires Brunswick Part No. TK-TT100-3Y208-F 120/208 Three Wye 4 Wire + Ground TK-TT100-3D240-F 120/240 Three Delta 4 Wire + Ground TK-TT100-3Y380-F 220/380 Three Wye 4 Wire + Ground TK-TT160-1S240-FB 120/240 Single Wye 3-wire = Ground StringPin Pinsetter Electrical Requirements 13

14 StringPin Pinsetter Overview (Rear Mount Controller) WITH CURTAIN WALL / MASKING UNIT ONE (1) STRING PIN CONTROLLER IS USED PER PAIR OF LANES AND WHEN LOCATED TO THE BACK OF THE MACHINE, IS MOUNTED TO THE BALL RETURN SIDE OF THE EVEN (RIGHT) LANE ELECTRICIAN TO HARD WIRE POWER CABLE INTO STRINGPIN CONTROLLER USING DROP CORD OR RIGID CONDUIT PER LOCAL CODE. THE STRINGPIN CONTROLLER BOX(ES) MUST BE CONNECTED TO A GROUNDED, METAL, PERMANENT WIRING SYSTEM; OR AN EQUIPMENT-GROUNDING CONDUCTOR MUST BE RUN WITH THE CIRCUIT CONDUCTORS AND CONNECTED TO THE EQUIPMENT-GROUNDING TERMINAL ON THE CONTROL BOX. ALL ELECTRICAL CONNECTIONS MUST COMPLY WITH LOCAL CODE OF THE AREA IN WHICH THE PINSETTER IS BEING INSTALLED (4826 mm) 4-6 (102 mm mm) CURTAIN WALL (BY CUSTOMER) 13 1 (3988 mm) 9 4 (2845 mm) LIGHTING FIXTURE LIGHTING FIXTURE CENTE OVER AISLE 4" (102 mm) FROM CURTAIN WALL /8 (4074 mm) MAIN POWER DROP ELECTRICAL JUNCTION BOX (BY CUSTOMER) 208/380VAC, 50/60 HZ, 3 PHASE 1 9-1/2 (545 mm) RIGID CONDUIT (BY CUSTOMER) OR DROP CORD (BY CUSTOMER) TYPE "S" SERVICE CORD, RUBBER SHEATHED, 4 OR 5 CONDUCTOR, 12 GAUGE 33.35" (847 mm) or 48.85" (1241 mm) OPEN GUARD STRINGPIN CONTROLLER (RIGHT/EVEN LANE) 66 (1676 mm) 20 (508 mm) BOTTOM OF MASKING UNIT 7 9-7/16 (2373 mm) 9 1-1/16 (2770 mm) REMOVABLE LADDER LANE SURFACE 21-5/8" (549 mm) 58-1/2 (1486 mm) 13 6 (4115 mm) PREFER 11 6 (3505 mm) MINIMUM 0 POINT (LANE SURFACE) 17' 1/2" (445 mm) CONCRETE FLOOR FOUNDATION I-JOISTS 70 6 (21590 mm) FROM CURTAIN WALL TO 17' ½" (445 mm) CONCRETE STEP FOUNDATION I-JOISTS NOTE: TOTAL STRING PINSETTER WEIGHT (PER PAIR) 2916 lb. (1322 kg) i SERVICE AISLE 5' (1524 mm) PREFER 3' (915 mm) MINIMUM 60' (18288 mm) HEAD PIN TO PINDECK SIDE OF FOUL LINE 84' 2-1/4" (25660 mm) TO 17 ½ (445 mm) STEP (EDGE OF APPROACH) 85' 3-3/8" (25994 mm) TO 17 ½ (445 mm) STEP (EDGE OF APPROACH) 85' 11-3/4" (26206 mm) TO 17 ½ (445 mm) STEP (EDGE OF APPROACH) WARNING!: CUSTOMERS SHOULD VALIDATE THAT THE SPECIFICATIONS OR ANY DEVIATIONS FROM THESE SPECIFICATIONS COMPLY WITH LOCAL REGULATIONS. NOTE!: Adherence to the designated specifications are required for compliance with the Machinery Directive. Figure 4 14 StringPin Pinsetter Electrical Requirements

15 WITH MASKING WALL ONE (1) STRING PIN CONTROLLER IS USED PER PAIR OF LANES AND WHEN LOCATED TO THE BACK OF THE MACHINE, IS MOUNTED TO THE BALL RETURN SIDE OF THE EVEN (RIGHT) LANE ELECTRICIAN TO HARD WIRE POWER CABLE INTO STRINGPIN CONTROLLER USING DROP CORD OR RIGID CONDUIT PER LOCAL CODE. THE STRINGPIN CONTROLLER BOX(ES) MUST BE CONNECTED TO A GROUNDED, METAL, PERMANENT WIRING SYSTEM; OR AN EQUIPMENT-GROUNDING CONDUCTOR MUST BE RUN WITH THE CIRCUIT CONDUCTORS AND CONNECTED TO THE EQUIPMENT-GROUNDING TERMINAL ON THE CONTROL BOX. ALL ELECTRICAL CONNECTIONS MUST COMPLY WITH LOCAL CODE OF THE AREA IN WHICH THE PINSETTER IS BEING INSTALLED (5080 mm) 4-6 (102 mm mm) MASKING WALL (BY CUSTOMER) (4242 mm) 9 4 (2845 mm) LIGHTING FIXTURE LIGHTING FIXTURE CENTE OVER AISLE MAIN POWER DROP ELECTRICAL JUNCTION BOX (BY CUSTOMER) 208/380VAC, 50/60 HZ, 3 PHASE /4 (4324 mm) 1 9-1/2 (545 mm) RIGID CONDUIT (BY CUSTOMER) OR DROP CORD (BY CUSTOMER) TYPE "S" SERVICE CORD, RUBBER SHEATHED, 4 OR 5 CONDUCTOR, 12 GAUGE IMPORTANT! MASKING WALL MUST BE CONSTRUCTED AFTER PINSETTERS ARE INSTALLED. OPEN GUARD STRINGPIN CONTROLLER (RIGHT/EVEN LANE) BOTTOM OF MASKING WALL 20 (508 mm) 7 9-7/16 (2373 mm) 9 1-1/16 (2770 mm) REMOVABLE LADDER LANE SURFACE 22" (559 mm) 60-1/2 (1537 mm) 13 6 (4115 mm) PREFER 11 6 (3505 mm) MINIMUM 0 POINT (LANE SURFACE) 17' 1/2" (445 mm) CONCRETE FLOOR FOUNDATION I-JOISTS 70 (21336 mm) FROM MASKING WALL TO 17' ½" (445 mm) CONCRETE STEP FOUNDATION I-JOISTS NOTE: TOTAL STRING PINSETTER WEIGHT (PER PAIR) 2916 lb. (1322 kg) i SERVICE AISLE 5' (1524 mm) PREFER 3' (915 mm) MINIMUM 60' (18288 mm) HEAD PIN TO PINDECK SIDE OF FOUL LINE 84' 2-1/4" (25660 mm) TO 17 ½ (445 mm) STEP (EDGE OF APPROACH) 85' 3-3/8" (25994 mm) TO 17 ½ (445 mm) STEP (EDGE OF APPROACH) 85' 11-3/4" (26206 mm) TO 17 ½ (445 mm) STEP (EDGE OF APPROACH) WARNING!: CUSTOMERS SHOULD VALIDATE THAT THE SPECIFICATIONS OR ANY DEVIATIONS FROM THESE SPECIFICATIONS COMPLY WITH LOCAL REGULATIONS. NOTE!: Adherence to the designated specifications are required for compliance with the Machinery Directive. Figure 5 StringPin Pinsetter Electrical Requirements 15

16 StringPin Pinsetter Overview (Front Mount Controller) WITH CURTAIN WALL / MASKING UNIT ONE (1) STRING PIN CONTROLLER IS USED PER PAIR OF LANES AND WHEN LOCATED TO THE BACK OF THE MACHINE, IS MOUNTED TO THE BALL RETURN SIDE OF THE EVEN (RIGHT) LANE ELECTRICIAN TO HARD WIRE POWER CABLE INTO STRINGPIN CONTROLLER USING DROP CORD OR RIGID CONDUIT PER LOCAL CODE. THE STRINGPIN CONTROLLER BOX(ES) MUST BE CONNECTED TO A GROUNDED, METAL, PERMANENT WIRING SYSTEM; OR AN EQUIPMENT-GROUNDING CONDUCTOR MUST BE RUN WITH THE CIRCUIT CONDUCTORS AND CONNECTED TO THE EQUIPMENT-GROUNDING TERMINAL ON THE CONTROL BOX. ALL ELECTRICAL CONNECTIONS MUST COMPLY WITH LOCAL CODE OF THE AREA IN WHICH THE PINSETTER IS BEING INSTALLED (4826 mm) 4-6 (102 mm mm) CURTAIN WALL (BY CUSTOMER) 9 4 (2845 mm) 4 8 (1422 mm) LIGHTING FIXTURE LIGHTING FIXTURE CENTE OVER AISLE MAIN POWER DROP ELECTRICAL JUNCTION BOX (BY CUSTOMER) 208/380VAC, 50/60 HZ, 3 PHASE 4" (102 mm) FROM CURTAIN WALL /8 (4074 mm) 1 9-1/2 (545 mm) 33.35" (847 mm) or 48.85" (1241 mm) DROP CORD (BY CUSTOMER) TYPE "S" SERVICE CORD, RUBBER SHEATHED, 4 OR 5 CONDUCTOR, 12 GAUGE OR RIGID CONDUIT (BY CUSTOMER) OPEN GUARD STRINGPIN CONTROLLER (RIGHT/EVEN LANE) 66 (1676 mm) BOTTOM OF MASKING UNIT 20 (508 mm) 7 9-7/16 (2373 mm) 9 1-1/16 (2770 mm) LANE SURFACE 21-5/8" (549 mm) 58-1/2 (1486 mm) 13 6 (4115 mm) PREFER 11 6 (3505 mm) MINIMUM 0 POINT (LANE SURFACE) 17' 1/2" (445 mm) CONCRETE FLOOR FOUNDATION I-JOISTS 70 6 (21590 mm) FROM CURTAIN WALL TO 17' ½" (445 mm) CONCRETE STEP NOTE: TOTAL STRING PINSETTER WEIGHT (PER PAIR) 2916 lb. (1322 kg) i SERVICE AISLE 5' (1524 mm) PREFER 3' (915 mm) MINIMUM 60' (18288 mm) HEAD PIN TO PINDECK SIDE OF FOUL LINE 84' 2-1/4" (25660 mm) TO 17 ½ (445 mm) STEP (EDGE OF APPROACH) 85' 3-3/8" (25994 mm) TO 17 ½ (445 mm) STEP (EDGE OF APPROACH) 85' 11-3/4" (26206 mm) TO 17 ½ (445 mm) STEP (EDGE OF APPROACH) WARNING!: CUSTOMERS SHOULD VALIDATE THAT THE SPECIFICATIONS OR ANY DEVIATIONS FROM THESE SPECIFICATIONS COMPLY WITH LOCAL REGULATIONS. NOTE!: Adherence to the designated specifications are required for compliance with the Machinery Directive. Figure 6 16 StringPin Pinsetter Electrical Requirements

17 WITH MASKING WALL ONE (1) STRING PIN CONTROLLER IS USED PER PAIR OF LANES AND WHEN LOCATED TO THE BACK OF THE MACHINE, IS MOUNTED TO THE BALL RETURN SIDE OF THE EVEN (RIGHT) LANE ELECTRICIAN TO HARD WIRE POWER CABLE INTO STRINGPIN CONTROLLER USING DROP CORD OR RIGID CONDUIT PER LOCAL CODE. THE STRINGPIN CONTROLLER BOX(ES) MUST BE CONNECTED TO A GROUNDED, METAL, PERMANENT WIRING SYSTEM; OR AN EQUIPMENT-GROUNDING CONDUCTOR MUST BE RUN WITH THE CIRCUIT CONDUCTORS AND CONNECTED TO THE EQUIPMENT-GROUNDING TERMINAL ON THE CONTROL BOX. ALL ELECTRICAL CONNECTIONS MUST COMPLY WITH LOCAL CODE OF THE AREA IN WHICH THE PINSETTER IS BEING INSTALLED (5080 mm) 4-6 (102 mm mm) MASKING WALL (BY CUSTOMER) 9 4 (2845 mm) 5 6 (1676 mm) LIGHTING FIXTURE LIGHTING FIXTURE CENTE OVER AISLE MAIN POWER DROP ELECTRICAL JUNCTION BOX (BY CUSTOMER) 208/380VAC, 50/60 HZ, 3 PHASE DROP CORD (BY CUSTOMER) TYPE "S" SERVICE CORD, RUBBER SHEATHED, 4 OR 5 CONDUCTOR, 12 GAUGE OR /4 (4324 mm) 1 9-1/2 (545 mm) IMPORTANT! MASKING WALL MUST BE CONSTRUCTED AFTER PINSETTERS ARE INSTALLED. RIGID CONDUIT (BY CUSTOMER) OPEN GUARD STRINGPIN CONTROLLER (RIGHT/EVEN LANE) BOTTOM OF MASKING WALL 20 (508 mm) 7 9-7/16 (2373 mm) 9 1-1/16 (2770 mm) LANE SURFACE 22" (559 mm) 60-1/2 (1537 mm) 13 6 (4115 mm) PREFER 11 6 (3505 mm) MINIMUM 0 POINT (LANE SURFACE) 17' 1/2" (445 mm) CONCRETE FLOOR FOUNDATION I-JOISTS 70 (21336 mm) FROM CURTAIN WALL TO 17' ½" (445 mm) CONCRETE STEP NOTE: TOTAL STRING PINSETTER WEIGHT (PER PAIR) 2916 lb. (1322 kg) i SERVICE AISLE 5' (1524 mm) PREFER 3' (915 mm) MINIMUM 60' (18288 mm) HEAD PIN TO PINDECK SIDE OF FOUL LINE 84' 2-1/4" (25660 mm) TO 17 ½ (445 mm) STEP (EDGE OF APPROACH) 85' 3-3/8" (25994 mm) TO 17 ½ (445 mm) STEP (EDGE OF APPROACH) 85' 11-3/4" (26206 mm) TO 17 ½ (445 mm) STEP (EDGE OF APPROACH) WARNING!: CUSTOMERS SHOULD VALIDATE THAT THE SPECIFICATIONS OR ANY DEVIATIONS FROM THESE SPECIFICATIONS COMPLY WITH LOCAL REGULATIONS. NOTE!: Adherence to the designated specifications are required for compliance with the Machinery Directive. Figure 7 StringPin Pinsetter Electrical Requirements 17

18 POWER OUTLET INFORMATION StringPin Controller POWER REQUIREMENTS - STRINGPIN PINSETTER CONTROLLER (LANE PAIR) VOLTS HERTZ AC/DC PHASE AMP WATTS CIRCUIT REQUIREMENT CUSTOMER RESPONSIBILITY BRUNSWICK RESPONSIBILITY /60 AC /60 AC WIRE WITH INSULATED GROUND (EARTH) 3 WIRE WITH INSULATED GROUND (EARTH) ALL POWER CABLING - CIRCUIT REQUIREMENTS - STRINGPIN CONTROLLER NON-ISOLATED GROUND SUB PANEL TOTAL WIRES PER CIRCUIT LANE PAIRS PER CIRCUIT WIRE SIZE BREAKER SIZE 380VAC 3-PHASE 208VAC 3 PHASE 5 (INCLUDES GROUND (EARTH) 4 (INCLUDES GROUND (EARTH) 2 12 GAUGE 16A 2 12 GAUGE 20A OUTLET LOCATION - STRINGPIN PINSETTER (PER LANE PAIR) ONE JUNCTION BOX 18 StringPin Pinsetter Electrical Requirements

19 StringPin Controller (Rear Mount) Figure 8 StringPin Pinsetter Electrical Requirements 19

20 StringPin Controller (Front Mount) Figure 9 20 StringPin Pinsetter Electrical Requirements

21 STRINGPIN CONTROLLER WIRING Internal - UL Version E-STOP POWER TO CONTROLLER PCB RESET LED (GREEN) POWER ON LED () GRN RESET LED (GREEN) V+ V+ V+ V+ V- V- V- V- POWER ON LED () POWER SUPPLY GRN RC RCG POK P FG N L GRN/ 2nd CONTACTOR A1 21 nc 5L3 3L2 1L nc no A2 22 6T3 4T2 2T1 GRN A1 21 nc 5L3 3L2 1L nc no A2 22 6T3 4T2 2T1 1st CONTACTOR GRN/ POWER TO HV PCB StringPin Pinsetter Electrical Requirements 21

22 Internal - CE Version E-STOP 2 1 POWER TO CONTROLLER PCB V- V- V- V- V+ V+ V+ V+ POWER SUPPLY L N FG P POK RCG RC GRN S11 S21 Y32 A Reset Fault Out Power In1 In2 PNOZ S3 A S12 S22 S34 GRN/ GRN A1 21 5L3 3L2 1L nd CONTACTOR A2 22 6T3 4T2 2T1 GRN GRN RESET LED (GREEN) POWER ON LED () RESET LED (GREEN) A1 21 5L3 3L2 1L A2 22 6T3 4T2 2T1 POWER ON LED () 1st CONTACTOR GRN/ POWER TO HV PCB 22 StringPin Pinsetter Electrical Requirements

23 Input Power - Wye Configuration (380V) GRN/ 2nd CONTACTOR A1 21 nc 5L3 3L2 1L nc no A2 22 6T3 4T2 2T1 GRN A1 21 nc 5L3 3L2 1L nc no A2 22 6T3 4T2 2T1 1st CONTACTOR GRN/ POWER TO HV PCB L1 L2 L3 N 3- PHASE INPUT GROUND ELECTRICIAN TO HARD WIRE POWER CABLE INTO SAFETY CONTROLLER AND PINSETTER CONTROL BOX(ES) USING RIGID CONDUIT. THE CONTROL BOX(ES) MUST BE CONNECTED TO A GROUNDED, METAL, PERMANENT WIRING SYSTEM; OR AN EQUIPMENT-GROUNDING CONDUCTOR MUST BE RUN WITH THE CIRCUIT CONDUCTORS AND CONNECTED TO THE EQUIPMENT-GROUNDING TERMINAL ON THE CONTROL BOX. ALL ELECTRICAL CONNECTIONS MUST COMPLY WITH LOCAL CODE OF THE AREA IN WHICH THE PINSETTER IS BEING INSTALLED. X Y X Y Z N PHASE X PHASE Y PHASE Z NEUTRAL Z N StringPin Pinsetter Electrical Requirements 23

24 Input Power - Delta Configuration (208V/230V) GRN/ 2nd CONTACTOR A1 21 nc 5L3 3L2 1L nc no A2 22 6T3 4T2 2T1 GRN A1 21 nc 5L3 3L2 1L nc no A2 22 6T3 4T2 2T1 1st CONTACTOR GRN/ L1 L2 L3 N POWER TO HV PCB X Y Z INSTALL JUMPER GROUND ELECTRICIAN TO HARD WIRE POWER CABLE INTO SAFETY CONTROLLER AND PINSETTER CONTROL BOX(ES) USING RIGID CONDUIT. PHASE X PHASE Y PHASE Z THE CONTROL BOX(ES) MUST BE CONNECTED TO A GROUNDED, METAL, PERMANENT WIRING SYSTEM; OR AN EQUIPMENT-GROUNDING CONDUCTOR MUST BE RUN WITH THE CIRCUIT CONDUCTORS AND CONNECTED TO THE EQUIPMENT-GROUNDING TERMINAL ON THE CONTROL BOX. Y ALL ELECTRICAL CONNECTIONS MUST COMPLY WITH LOCAL CODE OF THE AREA IN WHICH THE PINSETTER IS BEING INSTALLED. X Z 24 StringPin Pinsetter Electrical Requirements

25 Input Power - With Phase Converter GRN/ 2nd CONTACTOR A1 21 nc 5L3 3L2 1L nc no A2 22 6T3 4T2 2T1 GRN A1 21 nc 5L3 3L2 1L nc no A2 22 6T3 4T2 2T1 1st CONTACTOR GRN/ L1 L2 L3 N POWER TO HV PCB SL1 T3 SL2 INSTALL JUMPER 3- PHASE INPUT GROUND ELECTRICIAN TO HARD WIRE POWER CABLE INTO SAFETY CONTROLLER AND PINSETTER CONTROL BOX(ES) USING RIGID CONDUIT. THE CONTROL BOX(ES) MUST BE CONNECTED TO A GROUNDED, METAL, PERMANENT WIRING SYSTEM; OR AN EQUIPMENT-GROUNDING CONDUCTOR MUST BE RUN WITH THE CIRCUIT CONDUCTORS AND CONNECTED TO THE EQUIPMENT-GROUNDING TERMINAL ON THE CONTROL BOX. ALL ELECTRICAL CONNECTIONS MUST COMPLY WITH LOCAL CODE OF THE AREA IN WHICH THE PINSETTER IS BEING INSTALLED. SINGLE PHASE L-2 L-1 3 PHASE T-1 CONVERTER T-3 T-2 3-PHASE MAGNETIC STARTER (PROVIDED BY CUSTOMER) L-1 T-3 L-2 SL-1 T-3 SL-2 SL-1 T-3 SL-2 POWER PANEL StringPin Pinsetter Electrical Requirements 25

GS-Series Pinsetters and Associated Brunswick Bowling Equipment

Pre-Installation Manual GS-Series Pinsetters and Associated Brunswick Bowling Equipment Electrical Requirements January 2017 / 10-095400-041 Brunswick GS-Series Pinsetters and Associated Brunswick Bowling