SIGFOX END- PRODUCT FILING REQUIREMENT

Transcription

1 August 15th 2017 SIGFOX END- PRODUCT FILING REQUIREMENT Public use

2 Revision History Revision Number Date Author Change description 0.1 August 30 th, 2017 B.Ray Initial spec Content I. Introduction Acronyms and abbreviations Scope Introduction... 5 II. Project information General information... 8 II. Device information Online information in BUILD Documentation and test report upload in Build certification page i. Product based on a Sigfox Verified module Documentation upload Test report upload ii. Product based on a Sigfox Verified reference design Documentation upload Test report upload iii. Product based on another Sigfox Ready product (similarity) Documentation upload iv. Development solution based on a Sigfox Verified Module or Reference Design Documentation upload... 14

3

4 1. Introduction

5 I. Introduction 1. Acronyms and abbreviations - CE: European Commission - CW: Continuous wave - DUT: Device Under Test - EIRP: Effective Isotropic Radiated Power - EIRS: Effective Isotropic Radiated Sensitivity - ETSI: European Telecommunications Standards Institute - ERP: Effective Radiated Power - FCC: Federal Communications Commission - GFSK: Gaussian Frequency Shift Keying - PER: Packet Error Rate - RC: Radio Configuration - RF: Radio Frequency - RX: Receive - TX: Transmit 2. Scope This document applies to Sigfox partners planning a Sigfox Ready TM filing for an endproduct. This document intents to describe the filing requirements for every end-product going through a Sigfox Ready TM filing. 3. Introduction Filing is checked and approved by Sigfox SA through the BUILD platform at the BUILD certification page. However, some information related to the project and to the product itself needs to be filled prior to the filing submission as there are key for the product filing. (*) this mark indicates that the filed is mandatory for filing

6

7 2. Project information

8 II. Project information 1. General information Company name (*) Company address (*) Company URL Country (*) Technical contact HW/SW (*) o Name o address o Phone Sales contact at Sigfox

9 3. Device information

10 II. Device information 1. Online information in BUILD Commercial product name (should not include neither Sig nor Fox in its name) (*) Product brief description (*) Product URL Product version (*) Product datasheet URL Embedded sensors o Button o Accelerometer o Temperature ambient/room o Temperature external o Humidity / hygrometer ambient o Humidity / hygrometer wall/soil o CO2 o CO o GPS o Light o Pulse o Voltage o Proximity o Magnetometer o Tensometer o Reed switch o Infrared / PIR or active o Flood o Smoke o Ultrasonic o Wind / Anemometer o Water flow / consumption o Gas flow / consupmtion o Electricity flow / consumption o Gyroscope o Microphone o Geophone o Radiation alpha o Radiation beta o Radiation gamma o Radiation xrays o VOC o NOx o Hall effect o Barometer

11 o Pluviometer o Combustible gases o Other: Indoor / outdoor / industrial / living area usage o Indoor o Outdoor IP 44 o Outdoor IP 65 o Industrial usage o Living/office area usage o Personal/animal wear usage o Other: Other connectivity technologies used o LoRa o NB IoT o Bluetooth o WiFi o RFID o Ethernet o GSM o NFC o ZigBee/ZWave o IQRF o WMBus o Other: Vertical market (*) o Agriculture & Environment o Automotive & Fleet o Eval kit o Health o Home & Lifestyle o Industry o Public sector o Retail, Finance, other services o Utilities Modem manufacturer name (*) Reference of embedded transceiver, ref design or module (*) End-product operating temperature min and max Modem communication type (*) o Uplink only o Uplink and downlink Radio configuration (*) o RC1 o RC2 o RC3 o RC4 Supply (*) o Battery

12 Type Alkaline LiMNO2 LiSOCl2 LiPol/LiFePol Other Size AA AAA Coin cell Thin-soft-prismatic Other Brand Accessibility User replaceable User not replaceable Battery total voltage Count (1, 2 batteries) Total battery capacity in mah Typical number of messages per battery/charge cycle: o External power supply Type Reference Voltage o Harvesting product Solar panel Thermo electrical Antenna (*) o Internal o External o Connectorized o Type ½ wave Wire Wip PCB printed ¼ wave Helical Ceramic Fractal PIFA Other: Enclosure (*) o Plastic ABS (Acrylonitrile Butadiene Styrene) PC (Polycarbonate) o Metallic

13 o Other: Certification type (*) o Sigfox Ready End Product Certification Certification sub-type (*) o Product based on Sigfox Verified Module o Product based on SigfoxVerified Reference Design o Product based on another Sigfox Ready product (similarity) o Development solution based on a Sigfox Verified Module / Reference Design Sigfox Verified Modem certificate (*) Sigfox Verified Firmware revision (*) Sigfox Verified Library revision (*) Sigfox identifier in Sigfox cloud (*) Certification test house (*) o Emitech o TUV o 7layers o Eldorado o CTCadvanced o Dekra Radiation test date planned with test house Payload encryption activation by Sigfox Library (specific configuration required) (*) o Yes o No 2. Documentation and test report upload in Build certification page (*) i. Product based on a Sigfox Verified module Documentation upload Product datasheet Battery or power supply datasheet Antenna datasheet or antenna characteristics if internal design (polarization, gain (dbd or dbi), bandwidth, impedance, efficiency, Ros or VSWR, radiation pattern, connector type...) Picture of end-product in its environment (normal use) Internal photo of end-product with antenna to modem output path Test report upload Radiation test report from Sigfox accredited test house with EIRP and radiation pattern measurement Radiated sensitivity from Sigfox accredited test house (optional)

14 ii. Product based on a Sigfox Verified reference design Documentation upload Product datasheet Battery or power supply datasheet Antenna datasheet or antenna characteristics if internal design (polarization, gain (dbd or dbi), bandwidth, impedance, efficiency, Ros or VSWR, radiation pattern, connector type...) Picture of end-product in its environment (normal use) Internal photo of end-product with antenna to modem output path PCB layout of the Sigfox reference design section Bill of material (BOM) of the Sigfox reference design section Shematic of the Sigfox reference design section Test report upload Radiation test report from Sigfox accredited test house with EIRP and radiation pattern measurement Radiated sensitivity (optional) iii. Product based on another Sigfox Ready product (similarity) Documentation upload Similarity checklist showing comparison of the reference product and the product to be certified iv. Development solution based on a Sigfox Verified Module or Reference Design Documentation upload Product datasheet Battery or power supply datasheet Antenna datasheet or antenna characteristics if internal design (polarization, gain (dbd or dbi), bandwidth, impedance, efficiency, Ros or VSWR, radiation pattern, connector type...) Picture of end-product in its environment (normal use) Internal photo of end-product with antenna to modem output path For development solution based on reference design only : a. PCB layout of the Sigfox reference design section b. Bill of material (BOM) of the Sigfox reference design section c. Shematic of the Sigfox reference design section