MB E/02-E/03-E/04-E F 2 MC-16FX Family MB96640/690/6B0 Evaluation Board Operation Guide

Transcription

1 MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide Doc. No Rev. *A Cypress Semiconductor 98 Champion Court San Jose, CA Phone (USA): Phone (Intnl):

2 Copyrights Cypress Semiconductor Corporation, This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ( Cypress ). This document, including any software or firmware included or referenced in this document ( Software ), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, nonexclusive, nontransferable license (without the right to sublicense) () under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and () under those claims of Cypress s patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage ( Unintended Uses ). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A

3 Preface This document indicates directions for use about the "MB96640/690/6B0 evaluation board" which is the evaluation environment of MB96640/690/6B0 series of a F MC -6FX-6bit microcontroller *. *: Referred to MCU below. Using the product safely This manual contains important information for using this product safely. Be sure to read this manual before using the product, and to follow the directions given in this manual in order to use the product correctly. In particular, thoroughly read "Caution of the product described in this manual" at the start of this document, and perform a thorough safety check before using the product. Store this manual in a safe location where it can easily be accessed at any time while you are using the product. Related Manual You should refer to the following Manual as well: MCU Evaluation Board MB E OPERATION MANUAL Contents - MB96640/690/6B0 Evaluation Board uantity Description Part No. MB96640/690/6B0 Evaluation Board with socket MB E MB96640 Evaluation Board without socket (direct mounted) MB E MB96690 Evaluation Board without socket (direct mounted) MB E MB966B0 Evaluation Board without socket (direct mounted) MB E European RoHS compliance Products with an -E suffix on the part number are European RoHS compliant products. Notice on this document All information included in this document is current as of the date it is issued. Such information is subject to change without any prior notice. Please confirm the latest relevant information with the sales representatives. MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A

4 Preface Target products The available products with this evaluation board are shown below. Series Product Number (not included Package suffix) MB96640 MB96690 MB966B0 MB96F64R, MB96F64A MB96F645R, MB96F645A MB96F646R MB96F647R MB96F69R, MB96F69A MB96F695R, MB96F695A MB96F696R MB96F6B5R, MB96F6B5A MB96F6B6R Caution of the product described in this manual The following precautions apply to the product described in this manual. WARNING Electric shock, Damage Electric shock, Damage Indicates a potentially hazardous situation which could result in death or serious injury and/or a fault in the user s system if the product is not used correctly. Before performing any operation described in this manual, turn off all the power supplies to the system. Performing such an operation with the power on may cause an electric shock or device fault. Once the product has been turned on, do not touch any metal part of it. Doing so may cause an electric shock or device fault. CAUTION Cuts, Damage Damage Damage Damage Damage Damage Damage Indicates the presence of a hazard that may cause a minor or moderate injury, damages to this product or devices connected to it, or may cause to loose software resources and other properties such as data, if the device is not used appropriately. Before moving the product, be sure to turn off all the power supplies and unplug the cables. Watch your step when carrying the product. Do not use the product in an unstable location such as a place exposed to strong vibration or a sloping surface. Doing so may cause the product to fall, resulting in an injury or fault. Do not place anything on the product or expose the product to physical shocks. Do not carry the product after the power has been turned on. Doing so may cause a malfunction due to overloading or shock. Since the product contains many electronic components, keep it away from direct sunlight, high temperature, and high humidity to prevent condensation. Do not use or store the product where it is exposed to much dust or a strong magnetic or electric field for an extended period of time. Inappropriate operating or storage environments may cause a fault. Use the product within the ranges given in the specifications. Operation over the specified ranges may cause a fault. To prevent electrostatic breakdown, do not let your finger or other object come into contact with the metal parts of any of the connectors. Before handling the product, touch a metal object (such as a door knob) to discharge any static electricity from your body. When installing the sub board, align the key positions of main board connector and sub board connector, and fix with the screw set before use. When removing, remove all screws of screw set, then remove the sub board vertically from the main board. Otherwise, the product may be damaged, such as corruption of the connector section. Because the product has no casing, it is recommended that it be stored in the original packaging. Transporting the product may cause a damage or fault. Therefore, keep the packaging materials and use them when reshipping the product. MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 4

5 Contents. Overview Function overview Block diagram Function details Power supply settings Sub clock settings.... UART ch.0 select jumper....4 Mode SW settings OCD (On chip debugger) interface MB96640/690/6B0 Power supply select jumper Other jumper settings Signal monitor Main board connection Power-ON.... FOR TEST USE ONLY, External power supply connection pin.... Power-ON Circuit diagram Recycling China-RoHS Regulation... 4 Revision History... 5 Document Revision History... 5 MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 5

6 . Overview The MB96640/690/6B0 Evaluation Board provides the evaluative environment of the MB96640/690/6B0 series MCU. The whole of the Evaluation Board is shown below. Figure -. MB96640/690/6B0 Evaluation Board MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 6

7 Overview. Function overview This board can mount MCU (with or without socket). The location of the main function is shown as follows. Figure -. MB96640/690/6B0 Evaluation Board function overview Main/Sub connector monitor Sub xtal OCD I/F RS/USB sel (solder side) Main xtal Mode SW MCU monitor socket monitor Main/Sub connector (solder side) monitor External Power supply Connection pin MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 7

8 Overview Table -. MB96640/690/6B0 Evaluation Board function list Function Specification Remarks MCU MB96F640/690/6B0 with socket or direct mounted with socket NPACK00SD-ND HPACK00SD Oscillator Main clock 4MHz Sub clock.768khz with socket External power supply connection External power supply connection pin (DC.V to 5.0V) OCD connector OCD debugger(mb00-0-e) Connection MODE SW MB96640/690/6B0 mode switch NMIX SW MB96640/690/6B0 pin monitor land RS/USB select UART ch.0 connect to RS/USB by pin Jumper for transmission and reception. Main/sub connector 6pins ( rows pins) connector Connect to a connector on the Main board (mounted solder side).54mm pitch MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 8

9 Overview. Block diagram The block diagram of this board is shown below. Figure -. MB96640/690/6B0 Evaluation Board Block Diagram OCD connector Main board 4MHz DCV DC5V DC.V V 5.0V.V MCU (MB96640/ 690/6B0) khz With Socket 00 MODE SW Monitor land USART ch0 RS ch0 USB USART ch RS ch USART ch LIN ch0 USART ch4 LIN ch CAN ch0 CAN ch0 Monitor LED INT SW MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 9

10 . Function details The function details of this board are shown as follows.. Power supply settings Confirm the following jumpers are closed. (J, J4, J5, J4, J6) Figure -. Power supply jumpers location AVCC AVSS VCC_MCU AVRH AVRL MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 0

11 Function details Table -. Power supply jumpers function Jumper Function Setting J [VCC_MCU] Power supply for VCC pin Short-circuit (default) : ON Open : OFF J4 [AVRH] Power supply for AVRH pin Short-circuit (default) : ON Open : OFF J6 [AVRL] Power supply for AVRL pin Short-circuit (default) : ON Open : OFF J4 [AVCC] Power supply for AVCC pin Short-circuit (default) : ON Open : OFF J5 [AVSS] Power supply for AVSS pin Short-circuit (default) : ON Open : OFF. Sub clock settings The sub clock connection can be set as follows by J7 and J4. The settings of these jumpers are shown below. Note: A sub clock oscillator is not mounted in default. (Xtal.768kHz) Figure -. Sub clock setting jumpers location J7 J4 MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A

12 Function details Table -. J7 setting Setting XA connection select - XA connect to sub clock (default) - XA connect to 0 Table -. J4 setting Setting X0A connection select - X0A connect to GND 5-5 X0A connect to sub clock (default) X0A connect to 9 MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A

13 Function details. UART ch.0 select jumper The connection destination of the UART ch.0 signal can be selected by J0/J. These jumpers location and settings are shown below. Figure- UART ch.0 select jumper location J J0 From right to left,, J0:TX, J:RX Table -4. J0, J setting Setting Function select - RSC (default) - USB MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A

14 N O Function details.4 Mode SW settings The selection of the operational mode of MCU can be set by SW as follows. The mode switch location and settings are shown below. Figure -4. Mode SW location Mode SW bit:md, bit:debug Table -5. Mode SW setting (SW) ON OFF Mode SW setting, - MB96640/690/6B0 : serial writer mode MB96640/690/6B0 : user mode (default) MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 4

15 Function details.5 OCD (On chip debugger) interface The MB96640/690/6B0 evaluation board can operate software "Softune" for debugging by connecting Cypress OCD-E (on chip debugger). The OCD connector location and settings are shown below. Figure -5. OCD cable connect location OCD Connector Figure -6. How to connect OCD-E Turn the coaxial cable appended to Cypress OCD- E (MB00-0-E) as shown in a left chart. MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 5

16 Function details.6 MB96640/690/6B0 Power supply select jumper The MB96640/690/6B0 evaluation board can select the power supply connection for each device by jumper. This setup should be carried out corresponding to the device. It will become a cause of failure if this setup is not appropriate. The jumper location and settings are shown below. Figure -7. Power supply select jumper location Power Supply Select jumper Table -6. Power supply select jumper setting Jumper Function Setting J6 MB96690/6B0 GND MB96690/6B0 should close (other should open) J5 MB966B0 VCC MB966B0 should close (other should open) J4 MB96690 DVCC MB96690 should close (other should open) J MB96690 DVCC MB96690 should close (other should open) J MB96690 GND MB96690 should close (other should open) Note : Make all the jumpers open for MB96640 use. MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 6

17 Function details.7 Other jumper settings These jumpers in the table can control the connection between the MCU pin and the peripheral I/O. Table -7. Signal connection jumpers location Jumper Signal J8 J9 J0 J J J J9 J7 J8 J9 J0 J J J4 J5 J4 J6 RS I/F ch.0 (USB): RX RS I/F ch.0(usb): TX RS I/F ch. : RX RS I/F ch. : TX LIN I/F ch.0 : RX LIN I/F ch.0 : TX LIN_NSLP0 LIN I/F ch. : RX LIN I/F ch. : TX LIN_NSLP CAN I/F ch.0 : RX CAN I/F ch.0 : TX VCC_MCU : MCU power supply AVCC : analog power supply AVSS : analog ground AVRH : analog reference power supply high AVRL : analog reference power supply low MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 7

18 Function details.8 Signal monitor The correspondence of the signal monitor land and the MCU pin number is shown as follows. ( numbers are equal to MCU pin numbers.) Table -8. Monitor land list Pin No. Pin No. Pin No. Pin No MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 8

19 Function details.9 Main board connection The connection of MCU and I/O on the main board is shown below. General-purpose LED The correspondence table for the general-purpose LED mounted on the main board and the MCU pin number is shown below. Table -9. General-purpose LED MONITOR LED Parts number Pin number MB96640/690/6B0 Pin name LED0 LED8 77 P00_ LED LED9 78 P00_4 LED LED 79 P00_5 LED LED 80 P00_6 LED4 LED6 8 P0_0 LED5 LED7 8 P0_ LED6 LED40 84 P0_ LED7 LED4 85 P0_ Interrupt SW The correspondence of interruption SW mounted on the main board and the MCU pin number is shown below. Table -0. Interrupt switch INT SW Parts number Pin number MB96640/690/6B0 Pin name INT0 SW4 89 P0_7 (INT9) INT SW7 90 P0_0 (INT0) INT SW9 9 P0_ (INT) INT SW 9 P0_5 (INT) MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 9

20 Function details NMI SW The correspondence of NMI SW mounted on the main board and the MCU pin number is shown below. Table -. NMI switch NMI SW Parts number Pin number MB96640/690/6B0 Pin name NMI SW 99 NMI Reset SW The correspondence of RESET SW mounted on the main board and the MCU pin number is shown below. Table -. RESET switch Reset SW Parts number Pin number MB96640/690/6B0 Pin name RESET SW 60 RSTX Volume SW The correspondence of Volume SW mounted on the main board and the MCU pin number is shown below. Table -. Volume switch Volume SW Parts number Pin number MB96640/690/6B0 Pin name Volume VR P06_ (AN) MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 0

21 . Power-ON Basically, this board cannot turn on the power supply alone. Mount on the main board (MB E) and use it.. FOR TEST USE ONLY, External power supply connection pin The external power supply connection pin for test use is shown as follows. (VCC =.V to 5.0V) When you connect an external power supply to this pin, and you use alone this board, short-circuit J (DVCC) and J (AVCC). Figure -. External power supply connection pin location VCC GND. Power-ON Follow the user's manual for the Main board (MB E). MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A

22 4. Circuit diagram J0 WL--P (RS:pin-pin short) (USB:pin-pin short) R 005 0kohm 5% R 005 0kohm 5% C 5 0uF 5V C uF 5V C uF 5V C uF 5V WL--P J0 WL--P J WL--P J8 WL--P J J4 X0A 4 P04_0 (P04_0/X0A) 5 6 WLW--PW C pF 50V P04_6 J P04_7 J WL--P 690:DVCC 690:GND DVCC VCC_MCU 5 8 L BLMPG600SN 50 J4 WL--P C7 5 0uF 5V C uF 5V C 005 0pF 5V 4 5 C 5 0uF 5V C uF 5V WL--P J7 WL--P J8 WL--P J SW MD DEBUG CHS-0B 9 J4 J5 C J uF 6V WL--P 690:DVCC 6B0:VCC L BLMPG600SN 50 R ohm % CN7 HIFFB-6DA-.54DSA(7) R5 Non-Mount 005 Mohm 5% C uF 5V C 0 uf 6V C uF 5V J WL--P (RS:pin-pin short) (USB:pin-pin short) C uF 5V C6 5 0uF 5V C uF 5V U- MB96640 (NPACK00SD-ND) MB96640 (NPACK00SD-ND) 00pin socket type : NPACK00SD-ND (Socket Head : HPACK00SD) WL--P J WL--P J WL--P J9 WL--P J0 WL--P J OCD R CN 005 4ohm 5% HRM-00-4B(40) R ohm X 005 0kohm 5% R CN6 HIFFB-6DA-.54DSA(7) C6 005 pf 5V J7 PM--P 4 C pF 50V 0 J6 WL--4P R 005 Mohm 5% 4 C8 5 0uF 5V C uF 5V R5 Non-Mount 005 Mohm 5% C uF 5V R4 Non-Mount 005 Mohm 5% D RN6GTR A K C5 5 0uF 5V C uF 5V C uF 5V C uF 5V C uF 5V U- J5 P7_0 WL--P MB96F640 MainCLK IF C AT-49_4MHz_SK 005 0pF 50V C 005 0pF 50V J8 PM--P R 005 0ohm J7 WL--P R ohm J4 R7 WL--P ohm % R 608 0ohm % J5 WL--P J WL--P R8 R9 R R V0 84 C uF 5V R9 005 Mohm 5% C0 005 pf 5V C4 0 uf 6V C4 5 0uF 5V 5 J WL--P 9 J WL--P (CAN_TX0) P0_5 (CAN_TX) J6 WL--P R4 Non-Mount 005 Mohm 5% C uF 5V VCC_MCU AVSS AVCC R 005 0kohm 5% VCC MB96F640 Monitor pin (xx-yy =.54mm pitch) P0_7 P_0 P_ P_ P_ P_4 P_5 P_6 P04_4 P04_5 P06_ P06_ P06_4 P06_6 P06_7 AVRH AVRL P05_0 P05_ P05_ P05_4 P05_6 P05_7 P08_0 P08_ P08_ P08_ P08_4 P04_6 P04_7 P08_5 P08_6 P08_7 P09_0 P09_ P09_ P09_ P7_ P7_ P0_0 P0_ P0_ P0_ DEBUG_IF P7_0 MD X0 X X0A XA RSTX P_0 P_ P_ P_ P_4 P_5 P_6 P_7 P_0 P_ P_7 P00_0 P00_ P00_ P00_ P00_4 P00_5 P00_6 P00_7 P0_0 P0_ P0_ P0_ P0_4 P0_5 P0_6 P0_7 P0_0 P0_ P0_5 P0_0 P0_ P0_ P0_ P0_4 P0_5 P0_6 AVRH AVRL 99 MB96F640 MODE SET/OCD IF VCC DEBUG_IF MD R4 VCC MD 005 0kohm 5% X0 4MHz MB96F640 SubCLK IF khz XA (P04_/XA) P04_ DVCC P7_ P7_ Power Div IF VCC_MCU VCC Non-Mount LED CL-90G VCC_MCU VCC_MCU AVCC (CN7-5,6pin) AVCC AVRH AVRL AVRH AVRL 0 AVCC AVSS VCC DVCC_M AVCC DVCC_M DVCC DVCC VCC_MCU AVSS Main/Sub CN VCC P_5 [R8-R] 005 0kohm 5% P0_ P0_ P0_5 P_0 P0_6 P0_0 P0_6 P0_4 P0_4 P0_7 RSTX AVCC VCC +V VCC P06_ P0_0 P0_5 P00_4 P00_6 P0_ P0_ J5 WL--4P P0_7 P0_ P00_ P00_5 P0_0 P0_ DVCC_M +V0 P_4 C Non-Mount Non-Mount Vss P0_7/INT/SIN P_0/INT/SOT P_/INT/SCK P_/PPG0/TIN0/FRCK P_/PPG/TOT0/WOT P_4/SIN0/INT6 P_5/SOT0/ADTG/INT7 P_6/SCK0/CKOTX0 P04_4/PPG/SDA0 P04_5/PPG4/SCL0 P06_/AN/INT5/SIN5 P06_/AN/FRCK0 P06_4/AN4/IN0/TTG0/TTG4 P06_6/AN6/TIN/IN4_R P06_7/AN7/TOT/IN5_R AVcc AVRH AVRL AVss P05_0/AN8 P05_/AN0/OUT P05_/AN/OUT Vcc Vss P05_4/AN/INT_R/WOT_R P05_6/AN4/TIN P05_7/AN5/TOT P08_0/AN6 P08_/AN7 P08_/AN8 P08_/AN9 P08_4/AN0/OUT6 P04_6/SDA P04_7/SCL P08_5/AN/OUT7 P08_6/AN/PPG6_B P08_7/AN/PPG7_B P09_0/PPG8_R/AN4 P09_/PPG9_R/AN5 P09_/PPG0_R/AN6 P09_/PPG_R/AN7 P7_/PPG_R P7_/PPG_R P0_0/SIN/TIN/INT/AN8 P0_/SOT/TOT P0_/SCK/PPG6 P0_/PPG7 Vcc Vss DEBUG IF P7_0 MD X0 X Vss P04_0/X0A P04_/XA RSTX P_0 P_/PPG0_R P_/PPG_R P_/PPG_R P_4/PPG_R P_5/PPG4_R P_6/FRCK0_R/ZIN P_7/IN0_R/AIN P_0/IN_R/BIN P_/OUT_R P_7/INT_R P00_0/INT_R/FRCK P00_/INT4_R P00_/INT5_R Vcc Vss P00_/INT6_R/PPG8_B P00_4/INT7_R/PPG9_B P00_5/IN6/TTG/TTG6/PPG0_B P00_6/IN7/TTG/TTG7/PPG_B P00_7/INT4 P0_0/SCK7 P0_/CKOT/OUT0/SOT7 P0_/CKOTX/OUT/INT5/SIN7 P0_/PPG5 P0_4/SIN4/INT8 P0_5/SOT4 P0_6/SCK4/TTG P0_7/CKOTX_R/INT9/TTG/ZIN0/SCK7_R P0_0/CKOT_R/INT0/TTG4/AIN0/SOT7_R P0_/IN7_R/CKOT0_R/INT/BIN0/SIN7_R P0_5/OUT0_R/INT/SIN5_R P0_0/PPG4_B P0_/PPG5_B P0_/PPG4_B/SOT5_R P0_/PPG5_B/SCK5_R P0_4/RX0/INT4 P0_5/TX0 P0_6/INT0/NMI Vcc MODE GND X0A Oscillator DT-8_.768kHz_SK Oscillator XA 0 690/6B0 Jumper MB96F640 C-pin 690/6B0:GND (CN6-,5,6pin) VCC_MCU VCC_MCU GND AVRH AVRL AVCC AVRH AVSS AVRL AVCC AVSS Stand-alone J-J short (LIN_TX0) (LIN_NSLP0) (LIN_TX) (RS_TX0) (RS_TX) (NMI_SW) RS/USB_TX AVCC (LIN_RX0) (LIN_NSLP) (LIN_RX) (CAN_RX0) (CAN_RX) (RS_RX0) (RS_RX) (RESET) +5V0 (Volume_SW) (INT_SW) (INT_SW) (LED) (LED) (LED5) (LED7) (USB_RX0) +V VCC GND DVCC_M +V0 (INT_SW0) (INT_SW) (LED0) (LED) (LED4) (LED6) (USB_TX0) RS/USB_RX C C C MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A

23 5. Recycling Valid for European Union Countries: According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Cypress Semiconductor Europe GmbH Warehouse / Disposal Monzastraße 4a 65 Langen Gültig für EU-Länder: Gemäß der Europäischen WEEE-Richtlinie und deren Umsetzung in landesspezifische Gesetze nehmen wir dieses Gerät wieder zurück. Zur Entsorgung schicken Sie das Gerät bitte an die folgende Adresse: Cypress Semiconductor Europe GmbH Warehouse / Disposal Monzastraße 4a 65 Langen MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A

24 6. China-RoHS Regulation Compliance with Administration on the Control of Pollution Caused by Electronic Information Products of the People s Republic of China 这标记是按照 006 年 月 8 日公布的 [ 电子信息产品污染控制管理办法 ] 以及 SJ/T64-006[ 电子信息产品污染控制标识要求 ] 在中国销售的电子信息产品的环保使用期限 如遵守关于这产品的安全或使用上的注意, 在这期限内 ( 从生产日期起算 ) 不会因产品中的有害物质漏到外部 或发生突然变异, 而引起环境污染和对人体或财产的重大影响 产品中有毒有害物质或元素的名称及含量 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) 印刷线路板 电源 : 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 规定的限量要求以下 : 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 规定的限量要求 MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 4

25 Revision History Document Revision History Document Title: MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide Document Number: Revision Issue Date Origin of Change Description of Change ** /4/0 MITK Initial release *A 04/9/06 MITK Migrated Spansion Guide from SS v0-Eto Cypress format MB E/0-E/0-E/04-E F MC-6FX Family MB96640/690/6B0 Evaluation Board Operation Guide, Doc. No Rev. *A 5