SV-32 Network Security Appliance Quick Start Guide

Transcription

1 SV-32 Network Security Appliance Quick Start Guide This document explains how to set up the SV-32 for use with Security Center 6 Click here for the most recent version of this document. REV. 1

2 Copyright notice 2014 Genetec Inc. All rights reserved. Genetec Inc. distributes this document with software that includes an end-user license agreement and is furnished under license and may be used only in accordance with the terms of the license agreement. The contents of this document are protected under copyright law. The contents of this guide are furnished for informational use only and are subject to change without notice. Genetec Inc. assumes no responsibility or liability for any errors or inaccuracies that may appear in the informational content contained in this guide. This publication may not be copied, modified, or reproduced in any form or for any purpose, nor can any derivative works be created therefrom without Genetec Inc. s prior written consent. Genetec Inc. reserves the right to revise and improve its products as it sees fit. This document describes the state of a product at the time of document s last revision, and may not reflect the product at all times in the future. In no event shall Genetec Inc. be liable to any person or entity with respect to any loss or damage that is incidental to or consequential upon the instructions found in this document or the computer software and hardware products described herein. The use of this document is subject to the disclaimer of liability found in the end-user license agreement. Genetec, Omnicast, Synergis, Synergis Master Controller, AutoVu, Federation, the Genetec stylized G and the Omnicast, Synergis and AutoVu logos are trademarks of Genetec Inc., either registered or pending registration in several jurisdictions. Security Center, Security Center Mobile, Plan Manager, Sipelia and the Security Center logo are trademarks of Genetec Inc. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. All specifications are subject to change without notice. Document information Document title: SV-32 Network Security Appliance Quick Start Guide Document number: EN V6(1) Document update date: November 6, 2014 You can send your comments, corrections, and suggestions about this guide to documentation@genetec.com. ii EN V6(1)

3 Product documentation The product documentation is found in the following location: Genetec Technical Assistance Portal (GTAP). The latest version of the documentation is available from GTAP. Note, you ll need a username and password to log on to GTAP. EN V6(1) iii

4 Technical support Genetec Technical Assistance Center (GTAC) is committed to providing its worldwide clientele with the best technical support services available. As a Genetec customer, you have access to the Genetec Technical Assistance Portal (GTAP), where you can find information and search for answers to your product questions. Genetec Technical Assistance Portal (GTAP). GTAP is a support website that provides in-depth support information, such as FAQs, knowledge base articles, user guides, supported device lists, training videos, product tools, and much more. Prior to contacting GTAC or opening a support case, it is important to look at this website for potential fixes, workarounds, or known issues. You can log in to GTAP or sign up at Genetec Technical Assistance Center (GTAC). If you cannot find your answers on GTAP, you can open a support case online at gtap.genetec.com. For GTAC's contact information in your region see the Contact page at NOTE Before contacting GTAC, please have your System ID (available from the About button in your client application) and your SMA contract number (if applicable) ready. Licensing. For license activations or resets, please contact GTAC at For issues with license content or part numbers, or concerns about an order, please contact Genetec Customer Service at customerservice@genetec.com, or call (option #3). If you require a demo license or have questions regarding pricing, please contact Genetec Sales at sales@genetec.com, or call (option #2). Additional resources If you require additional resources other than the Genetec Technical Assistance Center, the following is available to you: GTAP Forum. The Forum is an easy to use message board that allows clients and Genetec staff to communicate with each other and discuss a variety of topics, ranging from technical questions to technology tips. You can log in or sign up at Technical training. In a professional classroom environment or from the convenience of your own office, our qualified trainers can guide you through system design, installation, operation, and troubleshooting. Technical training services are offered for all products and for customers with a varied level of technical experience, and can be customized to meet your specific needs and objectives. For more information, go to iv EN V6(1)

5 Contents Introduction What is the SV About SV-32 Hardware What is included in the SV-32 kit Hardware components Front view Back panel connections Before you install Keep product packaging Hardware requirements Site requirements Getting started Connecting the SV Default Windows users Logging on Product warranty What is covered What is not covered About product repairs and returns What should I do if the product is not working? How do I return the product? Where to find system information Find Security Center system license information Find the image version EN V6(1) v

6 Introduction Introduction This section provides an overview of the SV-32. For information about SV-32 image version, please see SV-32 Release Notes available on the GTAP Documents page, at What is the SV-32 The SV-32 is a compact-sized network security appliance that comes pre-installed with Genetec s Security Center and Windows Embedded Standard 7. It enables you to quickly deploy a unified or standalone video surveillance and access control system. 1 EN V6(1)

7 About SV-32 Hardware About SV-32 Hardware This section describes what is included in the SV-32 kit, and the hardware components of the SV-32. What is included in the SV-32 kit The SV-32 kit contains the following: SV-32 appliance 12V DC power supply 1x North American power cord 1x EU and 1x UK power cords (supplied with European orders only) HDMI to DVI adapter 3.5mm to RCA audio cable 12V DC power cable with pigtail Two mounting brackets IMPORTANT Verify the content of the box. If any component is missing, please notify Genetec within 30 days. EN V6(1) 2

8 About SV-32 Hardware Hardware components Hardware specifications CPU Chipset Memory Storage Intel Core i7-3555le 64 bit dual core 2.5GHz Intel 7 Series System Controller Hub QM77 8GB DDR3 Internal: 2TB or 4TB Storage Options; 2.5" SATA hard drives 60GB msata drive External: Network Attached Storage (NAS) or external SATA drive (esata) Display HDMI up to 1920 x 1200 DisplayPort up to 2560 x 1600 Audio Ethernet ports 7.1 channel S/PDIF 2x GbE ports USB 2x USB 3.0, 5 Gbps 2x USB 2.0, 480 Mbps Serial Power Operating temperature 1 x RS-232 Ultra mini serial connector 9.5 to 15V DC Up to 35W 0 C to 45 C (32 F to 113 F) with HDD 3 EN V6(1)

9 About SV-32 Hardware Front view All-metal fanless case Power and drive activity LEDs EN V6(1) 4

10 About SV-32 Hardware Back panel connections Audio S/PDIF 7.1 in Audio S/PDIF 7.1 out Power button (auto-reboot) 2x port USB 3.0 2x port USB 2.0 Mini serial (RS-232) 12VDC power esata port DisplayPort HDMI port Dual GbE LAN 4 x 2.5 SATA drive bays 5 EN V6(1)

11 Before you install Before you install This section describes the things you need to know and do before you install the product. Keep product packaging It is best practice to keep the product packaging in case you have to return the product. Hardware requirements To use the SV-32, you need the following items: Ethernet connection Display monitor with a DVI, HDMI, or DisplayPort input and DVI, HDMI, or DisplayPort cable USB keyboard USB mouse Site requirements Prepare the site as follows: Provide adequate ventilation. The SV-32 does not have a fan. Heat dispersion is managed by the aluminum enclosure. CAUTION If you are using multiple SV-32 units, do not stack them on top of one another. Clear space behind the SV-32. To prevent the SV-32 from accidentally turning off, ensure nothing is touching (or is too close to) the power button. EN V6(1) 6

12 Getting started Getting started This section contains the basic procedures to get started using the SV-32. Connecting the SV-32 1 Connect your HDMI monitor to the SV-32 HDMI connector. If required, use the HDMI to DVI adapter or use the Display port. If it is not turned on, then turn on the monitor. 2 Connect the keyboard and mouse to the two USB ports. 3 (Optional) Connect your speakers to the S/PDIF line-out jack. 4 Plug your Ethernet cable into either of the available Ethernet ports. 5 Insert the DC plug into the 12V DC input jack on the SV-32 and turn it clockwise until the plug is secured. 6 Plug the DC power supply into an AC outlet. Note The SV-32 automatically turns on when connected to a power source. Default Windows users When you start up the SV-32, the following two Windows users are created by default: Admin (full admin access) Default password: admin Access to the SV Control Panel Operator (limited access) Default password: operator Access to C: drive Access to Security Desk through a desktop link Cannot access the SV Control Panel Cannot access video drives Cannot modify system settings Start menu contains Computer icon only 7 EN V6(1)

13 Getting started Limited desktop icons (recycle bin, libraries) Cannot shut down/restart Windows Logging on The first time you start the SV-32, you are automatically logged in as the Operator user and the SV Control Panel and SV-32 setup wizard will open to guide you through the initial setup of your system. What you should know You will only be logged on to Windows automatically the first time the machine is started. After that, a Username and Password is required to log on to the machine. The SV Control Panel will only open automatically the first time the machine is started. After that, a user will be prompted to enter Admin credentials to have access to the SV Control Panel. To log on to SV Control Panel: 1 When prompted, enter the admin user credentials. 2 Click Connect. The SV Control Panel opens. For more details about using the SV Control Panel to configure your system, see the SV Control Panel User Guide. This guide is accessible by clicking the Control Panel: User guide (PDF) link on the About page in the SV Control Panel, or from the GTAP Documents page, at EN V6(1) 8

14 Product warranty Product warranty This section explains what is covered and what is not covered by the product warranty. What is covered Genetec guarantees the product against defects in materials and assembly in the course of normal use and service, for a period of 3 years from the date of shipment. Genetec Hardware Warranties cover the product Hardware. Please contact Genetec Technical Assistance for more information. What is not covered The following items are not covered by the Genetec Standard Hardware Warranty: Any equipment not furnished by Genetec which is attached to or used in conjunction with a product. A product which is used with any ancillary equipment that is not furnished by Genetec. Shipping cost to return a product to Genetec. Defects or damage resulting from customer's improper testing, operation, installation, maintenance, modification, alteration, or adjustment. Defects or damage from misuse, accident or neglect. Defects or damage resulting from use of the product in a manner other than its normal and customary manner. Defects or damage resulting from drilling holes, adding decals or other adhesives, or by painting the product. Defects or damage due to lightning or other electrical discharge. Product that is disassembled or repaired in such a manner as to adversely affect performance or prevent adequate inspection and testing to verify any warranty claim. Modification or abuse of, or tampering with, the product. Normal wear and tear. Installation, maintenance, or service of the product. 9 EN V6(1)

15 About product repairs and returns About product repairs and returns This section explains the product return process. What should I do if the product is not working? Contact Genetec Technical Assistance for troubleshooting. An RMA form will be issued to you if the problem cannot be resolved. For information, see Technical support on page iv. How do I return the product? If a replacement unit is required, you must complete the RMA form provided by Genetec Technical Assistance before being issued an RMA number. Once you are given a number, you can then return the defective unit. The customer is responsible for all return shipping charges, and Genetec will pay the shipping charges to send the repaired product back to the customer. IMPORTANT If no problem is found with the unit, the customer is invoiced. Where to find system information You need to have all system information on hand when contacting Genetec Technical Support, such as the System ID number and image version. Find Security Center system license information 1 Open the SV Control Panel. If you re not logged on as the Admin user, you will be prompted to enter admin credentials. 2 Click About. The information is displayed under License. You can also click Show full license for more detailed information. Find the image version 1 Open the SV Control Panel. If you re not logged on as the Admin user, you will be prompted to enter admin credentials. 2 Click About. The image version is listed beside Software revision under System. EN V6(1) 10

16 Compliance statements FCCID VQF-RT3090-1T1R CE EN V1.6.1 ( ) and EN V1.2.1 ( ) SV 32 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: - This device may not cause harmful interference, and - This device must accept any interference received, including interference that may cause undesired operation. Any changes or modification to the product not expressly approved by Genetec could void the user s authority to operate this device. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from which the receiver is connected. Consult the dealer or an experienced radio/tv technician.