Moulding Selection Guide 2011/2012

Transcription

1 Innovative Solutions / Beautiful Homes $5 2011/2012

2 Green Initiatives MOULDING & MILLWORK INC. AND OUR AFFILIATED BUSINESSES ARE COMMITTED TO SUSTAINABLE BUSINESS PRACTICES. We are proudly promoting the use of certified, low emitting, and recycled wood products, including our new SPERO moulding line. In addition, we are setting up Sustainable Operating Standards, which includes responsible manufacturing processes, chain of custody certifications, recycling programs, energy reduction programs, low carbon emission vehicle fleets, and memberships to regional and national Green councils. Moulding & Millwork, through our manufacturing facilities and affiliates, have the ability to provide products that may contribute to LEED rating points in the following areas: Materials & Resources, 4.1, 4.2, 5.1, 5.2, 7 Indoor Environmental Quality, 4.4 Manufacturing Distribution Locations Contains no urea-formaldehyde Surrey Maple Ridge Calgary Seattle Ferndale Richmond Toronto Lexington Vancouver (2) Edmonton Calgary Saskatoon Regina Winnipeg Toronto (2) Montréal Dartmouth Anchorage Seattle Portland Spokane Chicago Baltimore Pittsburgh Detroit Atlanta Charlotte Orlando Denver Phoenix Salt Lake City Newark Rochester Boston Dallas

3 Table of Contents 1 Green Building Initiative 2 Corporate Map 3 Illustration / Glossary 5 s 8 & Architraves 9 s 14 s 21 Ultralite Supercoat 27 s 28 Coves 28 Corners 29 Chair Rails 31 Full, Half, and Quarter Rounds & Base Shoes 32 Brickmoulds & Lattice 32 Handrails 33 Door Stops 34 Wainscot 34 Base Caps 35 Screen Moulds & Parting Beads 36 Window Stools 36 Miscellaneous Profiles 38 Accessories 39 S4S Boards & Flex Moulding 40 Jambs & Exterior Frames 41 Case/Base Combinations 42 Ceiling Trim 44 Product Index 46 Moulding Gallery WM# 535M /16 x 3-1/2-17 Ultralite Profile Code Profile Sizes Profile Species ARCHITRAVES: In cl assical architecture, it described the main beam resting on the tops of the columns. Today it is often used as a decorative moulding for ornamentation or finishing at the top of windows and doors. BASEBOARDS: s are placed along the wall at the floor. They should be chosen to work in harmony with your casings to finish and tie the room together. s are usually thinner than the casing. BUILD-UPS: Combining two or more moulding profiles to create a new or custom look. Also called stacking, build-ups make it easy to create the look of custom made trimwork without the high cost. CASING: s define the overall character of a room and are often the most visible part of the trim. They are used primarily to cover the gap between drywall and the door or window frame. s are generally thicker than the base mouldings. CROWNS: s are placed along the wall at the ceiling. They come in a wide range of patterns and sizes. s soften the transition from wall to ceiling while adding a distinctive look and charm to your room. FINISH BOARDS: Finish Boards come in either S4S (Surfaced 4 Sides) or S3S (Surfaced 3 Sides) and are used for a multitude of purposes including shelving, window liner, bases, casing, etc. PANEL MOULDS: Panel Moulds are used to frame wall paneling and add an accent to your walls. Often used in furniture construction. RAKE MOULD: Rakes are often used as crowns. In fact, they are sometimes called solid crowns. WAINSCOT: Trimwork installed in the area below a chair rail. Numerous options are available including raised panel, shadow box and beaded. Combined with a chair rail and baseboard, Wainscoting creates a dramatic look to any room. WINDOW STOOL: Also called window sill, a Window Stool is the surface installed below the sash of a window. Trim installed under window stool creates a distinctive look and adds a decorative touch. GLOSSARY OF TERMS BASE SHOES: Base shoes are primarily used to trim flooring materials and are often used in combination with a traditional baseboard to conceal variations between the flooring and the base. However, this versatile profile works great to solve numerous trimming needs. BATTENS/OPEN TRIM: A Batten/Open Trim is a narrow strip of wood used to cover joints or as decorative vertical members over plywood or wide boards. BEADED CEILING: A popular profile used often as wainscot paneling. Combined with a chair rail or cap mould and a baseboard, beaded ceiling makes a distinctive wainscot package. BRICKMOULDS: A Brickmould is mainly used as exterior casing around doors. 2 inches is the most common size, however, 1-1/2 and 1-1/4 inch sizes are available. Brickmoulds can also be used in place of a crown, and as a transition under window sills. BULLNOSE: A term used to describe the eased edges of trim and stops. A single bullnose stop would have one eased edge and a square edge back. A double bull nose stop would have two eased edges. CHAIR RAILS: Chair Rails are practical as well as decorative. Applied to a wall, from 24 to 48 inches up from the floor, they protect the wall from scuffs and dents from the backs of chairs as well as adding a beautiful accent to any room. CORNERS: Corners are used to protect the outside edges of the wall from damage and abrasion. Corners come in a wide variety of sizes and detailing. COVES: Coves are commonly used to soften the transition on inside corners but may be used for a wide range of applications. DENTIL: A moulding pattern with a series of closely spaced rectangular blocks and spaces. Used especially in classic architecture. DOOR STOPS: The Door Stop mouldings are attached to the door jamb on both sides and at the top. It is where the door comes to a rest when it is closed stopping the door from moving any further, and covering the gap that would otherwise appear between the door and the jambs. FULL ROUNDS: Full Rounds are used for numerous purposes and projects. Some of the more common uses are closet poles, curtain rods and towel rods. HALF ROUNDS: A cross section of a Half Round looks like a half circle and is used primarily as decorative trim. It works well as a trim piece for wall paper or to add a decorative pattern to flat panels. This profile can also be used to put a rounded edge on various shelving. HANDRAILS: Handrails provide safety and support. QUARTER ROUNDS: Quarter Rounds come in several sizes and serve a variety of functions. They are most often used with baseboards. RETURN: Term used to indicate the method of carrying a mouldings detail from the front of the moulding back to the wall. Generally a 45 degree cut is made to the front of the long moulding and an opposite 45 is cut on a small piece to carry the detail to the wall. SCREEN MOULD: A very versatile profile; Screen Mould fits a wide variety of needs and uses. Traditionally used to hold mesh screening into wood screens, it also works well as edge trim on various shelving or wood trim for wall paper etc. 4

4 s s s define the overall character of a room and are often the most visible part of the trim. They are used primarily to cover the gap between drywall and the door or window frame. s are generally thicker than the base mouldings. 433P 9/16 x 3-1/4-17 Primed FJ s define the overall character of a room and are often the most visible part of the trim. They are used primarily to cover the gap between drywall and the door or window frame. s are generally thicker than the base mouldings. 314MI102 15mm x 3-1/4-102 Ultralite MDF Ranch 327PF17 11/16 x 2-1/4-17 Primed FJ 327PI85 11/16 x 2-1/4-85 Primed FJ /16 x 2-1/4 - RDM Solid Pine 327F07 11/16 x 2-1/4-7 Solid Pine 473P 9/16 x 2-1/4-17 Primed FJ 1830PF17 11/16 x 3-1/2-17 Primed FJ 1830MF17 11/16 x 3-1/2-17 Ultralite MDF Beaded 376PF17 11/16 x 2-1/4-17 Primed FJ 376PI85 11/16 x 2-1/4-85 Primed FJ Feather Edge 366MF17 15mm x 2-1/4-17 Ultralite MDF 366MI85 15mm x 2-1/4-7 Ultralite MDF 366FJF17 11/16 x 2-1/4-17 Raw Fingerjoint 366FJI85 11/16 x 2-1/4-85 Raw Fingerjoint 366PF17 11/16 x 2-1/4-17 Primed FJ 366PI102 11/16 x 2-1/4-102 Primed FJ 366PI85 11/16 x 2-1/4-85 Primed FJ /16 x 2-1/4 - RDM Solid Pine 366F07 11/16 x 2-1/4-7 Solid Pine Colonial 356MI85 15mm x 2-1/4-7 Ultralite MDF 356PF17 11/16 x 2-1/4-17 Primed FJ 356PI102 11/16 x 2-1/4-102 Primed FJ /16 x 2-1/4 - RDM Solid Pine 356PI85 11/16 x 2-1/4-85 Primed FJ 356FJI85 11/16 x 2-1/4-85 Raw Fingerjoint 356F07 11/16 x 2-1/4-7 Solid Pine Beaded 445LMF17 18mm x 3-1/4-17 Ultralite MDF 445FJF17 11/16 x 3-1/4-17 Raw Fingerjoint 445PF17 11/16 x 3-1/4-17 Primed FJ 445PI87 11/16 x 3-1/4-87 Primed FJ /16 x 3-1/4 - RDM Solid Pine Colonial 444PF17 11/16 x 3-1/2-17 Primed FJ /16 x 3-1/2 - RDM Solid Pine 390HPF17 1-1/16 x 2-3/8-17 Primed FJ 535MF17 18mm x 3-1/2-17 Ultralite MDF 5 6

5 s s define the overall character of a room and are often the most visible part of the trim. They are used primarily to cover the gap between drywall and the door or window frame. s are generally thicker than the base mouldings. 37LPF17 11/16 x 2-1/4-17 Primed FJ Fluted/Reeded 37PF17 11/16 x 3-1/4-17 Primed FJ 1002P 9/16 x 3-9/16-17 Primed FJ s & Architraves s define the overall character of a room and are often the most visible part of the trim. They are used primarily to cover the gap between drywall and the door or window frame. s are generally thicker than the base mouldings. In classical architecture, an architrave described the main beam resting on the tops of the columns. Today it is often used as a decorative moulding for ornamentation or finishing at the top of windows and doors. Architrave 5010LM 30mm x 5-1/4-16 Ultralite MDF RB3/Delta Howe 523MF17 25mm x 3-1/2-17 Ultralite MDF 523PF17 1-1/16 x 3-1/2-17 Primed FJ /16 x 3-1/2 - RDM Solid Pine 312M3P 13/16 x 3-3/8 x 17 Primed FJ 411M 11/16 x 3-17 Ultralite MDF 462LP 11/16 x 2-3/4-17 Primed FJ 8063MF17 11/16 x 3-1/4-17 Ultralite MDF 9063M 25mm x 4-1/4-17 Ultralite MDF 9053M 25mm x 4-1/2-17 Ultralite MDF /Architrave 523LPF17 11/16 x 3-1/4-17 Primed FJ Baby Howe 0300BPF17 11/16 x 2-1/ BPI85 11/16 x 2-1/4-85 Primed FJ Primed FJ 7 8

6 s s are placed along the wall at the floor. They should be chosen to work in harmony with your casings to finish and tie the room together. s are usually thinner than the casing. 412M 9/16 x 4-1/4-16 Ultralite MDF s s are placed along the wall at the floor. They should be chosen to work in harmony with your casings to finish and tie the room together. s are usually thinner than the casing. Step Base 631M 12mm x 3-1/4-16 Ultralite MDF 631P 9/16 x 3-1/4-16 Primed FJ 631 9/16 x 3-1/4 - RDM Solid Pine 631FJ 9/16 x 3-1/4-16 FJ Pine 631LP 631LM Step Base 9/16 x 5-1/4-16 Primed FJ 9/16 x 5-1/4-16 Ultralite MDF Ogee Base 620M 12mm x 4-1/4-16 Ultralite MDF 620FJ 9/16 x 4-1/4-16 Raw Fingerjoint 620P 9/16 x 4-1/4-16 Primed FJ 620 9/16 x 4-1/4 - RDM Solid Pine M 15mm x 6-1/2-16 Ultralite MDF 9263M 18mm x 7-16 Ultralite MDF 725P 11/16 x 7-1/4-16 Primed FJ 9253M 18mm x 6-3/4-16 Ultralite MDF 725BM 18mm x 7-1/4-16 Ultralite MDF Ogee Base 623M 12mm x 3-1/4-16 Ultralite MDF 623FJ 9/16 x 3-1/4-16 Raw Fingerjoint 623P 9/16 x 3-1/4-16 Primed FJ 623 9/16 x 3-1/4 - RDM Solid Pine Ogee Base 618M 12mm x 5-1/4-16 Ultralite MDF 618FJ 9/16 x 5-1/4-16 Raw Fingerjoint 618P 9/16 x 5-1/4-16 Primed FJ 618 9/16 x 5-1/4 - RDM Solid Pine Ranch Base 713P 9/16 x 3-1/4-16 Primed FJ 713 9/16 x 3-1/4 - RDM Solid Pine 10

7 s s s are placed along the wall at the floor. They should be chosen to work in harmony with your casings to finish and tie the room together. s are usually thinner than the casing. Speed Base 5180M 15mm x 5-1/4-16 Ultralite MDF 5180FJ 9/16 x 5-1/4-16 Raw Fingerjoint 5180P 9/16 x 5-1/4-16 Primed FJ /16 x 5-1/4 - RDM Solid Pine s are placed along the wall at the floor. They should be chosen to work in harmony with your casings to finish and tie the room together. s are usually thinner than the casing. 151P 9/16 x 5-1/4-16 Primed FJ 414M 15mm x 3-7/8-16 Ultralite MDF Speed Base 163EM 15mm x 5-1/4-16 Ultralite MDF 163ESP 9/16 x 5-1/4-16 Primed FJ 163ES 9/16 x 5-1/4 - RDM Solid Pine 545M 15mm x 5-16 Ultralite MDF Victorian 1692M 15mm x 5-1/4-16 Ultralite MDF /16 x 5-1/4 - RDM Solid Pine Speed Base 4180P 9/16 x 4-1/4-16 Primed FJ 6180P 11/16 x 6-1/4-16 Primed FJ 1692P 9/16 x 5-1/4-16 Primed FJ 163E7M 15mm x 7-1/4-16 Ultralite MDF 11 12

8 s s s are placed along the wall at the floor. They should be chosen to work in harmony with your casings to finish and tie the room together. s are usually thinner than the casing. 526M 9/16 x 5-1/4-16 Ultralite MDF s are placed along the wall at the ceiling. They come in a wide range of patterns and sizes. s soften the transition from wall to ceiling while adding a distinctive look and charm to your room. 433P 9/16 x 3-1/4-17 Primed FJ 60M 18mm x 5-5/16-16 Ultralite MDF 504LMS 11/16 x 7-1/4-16 Ultralite MDF 6140P 11/16 x 6-1/4-16 Primed FJ 688P 9/16 x 5-1/4-16 Primed FJ 92M 9/16 x 7-3/8-16 Ultralite MDF 13 14

9 s s s are placed along the wall at the ceiling. They come in a wide range of patterns and sizes. s soften the transition from wall to ceiling while adding a distinctive look and charm to your room. s are placed along the wall at the ceiling. They come in a wide range of patterns and sizes. s soften the transition from wall to ceiling while adding a distinctive look and charm to your room. 458M 11/16 x 4-5/8-16 Ultralite MDF 45LM 15mm x 5-1/4-16 Ultralite MDF 41M 30mm x 6-5/16-16 Ultralite MDF 665M 11/16 x 6-1/4-16 Ultralite MDF 721M 25mm x 7-1/4-16 Ultralite MDF 677M 11/16 x 7-3/4-16 Ultralite MDF 75P 9/16 x 1-5/8-16 Primed FJ 75 9/16 x 1-5/8 - RDM Solid Pine 15 16

10 s s are placed along the wall at the ceiling. They come in a wide range of patterns and sizes. s soften the transition from wall to ceiling while adding a distinctive look and charm to your room. 52P 9/16 x 2-3/4-16 Primed FJ 52 9/16 x 2-3/4 - RDM Solid Pine s s are placed along the wall at the ceiling. They come in a wide range of patterns and sizes. s soften the transition from wall to ceiling while adding a distinctive look and charm to your room. 47M 15mm x 4-5/8-16 Ultralite MDF 47LP 9/16 x 4-5/8-16 Primed FJ 47L 9/16 x 4-5/8 - RDM Solid Pine 51P 9/16 x 3-1/4-16 Primed FJ 45LFJ 9/16 x 5-1/4-16 Raw Fingerjoint 45LP 9/16 x 5-1/4-16 Primed FJ 45L 9/16 x 5-1/4 - RDM Solid Pine 48 9/16 x 4-1/4 - RDM Solid Pine 48P 9/16 x 4-1/4-16 Primed FJ 48M 9/16 x 4-1/4-16 Ultralite MDF Big Cove 45BCP 9/16 x 5-1/4-16 Primed FJ 45BCM 9/16 x 5-1/4-16 Ultralite MDF 714LP 11/16 x 7-1/4-16 Primed FJ

11 s s s are placed along the wall at the ceiling. They come in a wide range of patterns and sizes. s soften the transition from wall to ceiling while adding a distinctive look and charm to your room. 785M 18mm x 4-5/8-16 Ultralite MDF s are placed along the wall at the ceiling. They come in a wide range of patterns and sizes. s soften the transition from wall to ceiling while adding a distinctive look and charm to your room. 614P 11/16 x 6-1/4-16 Primed FJ 814M 15/16 x 8-3/16-16 Ultralite MDF 714P 11/16 x 7-16 Primed FJ 714M 11/16 x 7-1/4-16 Ultralite MDF 270M 18mm x 6-3/4-16 Ultralite MDF 19 20

12 ULTRALITE SUPERCOAT ULTRALITE SUPERCOAT Mdf MOUldiNGS Ultralite Supercoat Mouldings s & s s 314MI102 15mm x 3-1/4 356M 15mm x 2-1/4 366MF17 15mm x 2-1/4 445LMF17 18mm x 3-1/4 8063M 11/16 x 3-1/4 535MF17 18mm x 3-1/2 1830MF17 11/16 x 3-1/2 9063M 25mm x 4-1/4 ULTRALITE SUPERCOAT Mdf MOUldiNGS Light Weight Installs with Ease Superior Paintability 9053M 25mm x 4-1/2 523MF17 25mm x 3-1/2 5010LM Architrave 30mm x 5-1/4 414M 631M Base 15mm x 3-7/8 12mm x 3-1/4 623M Base 620M Base 618M Base 12mm x 3-1/4 12mm x 4-1/4 12mm x 5-1/4 Superior Workabilty 22 ALL PROFILES AT 50% OF ACTUAL SIZE.

13 Ultralite Supercoat Mouldings s ULTRALITE SUPERCOAT Ultralite Supercoat Mouldings s 49M 15mm x 3-5/8 48M 9/16 x 4-1/4 47M 15mm x 4-5/8 45LM 15mm x 5-1/4 8263M Base 15mm x 6-1/2 9253M Base 18mm x 6-3/4 9263M Base 18mm x 7 725BM Base 18mm x 7-1/4 92M Base 9/16 x 7-3/8 163E7M Base 15mm x 7-1/4 631LM Base 9/16 x 5-1/4 45BCM 9/16 x 5-1/4 60M 18mm x 5-5/16 665M 11/16 x 6-1/4 714M 11/16 x 7-1/4 545M Base 15mm x M Base 15mm x 5-1/4 163EM Base 15mm x 5-1/4 526M Base 9/16 x 5-1/4 1692M Base 15mm x 5-1/4 458M 11/16 x 4-5/8 41M 30mm x 6-5/16 721M 25mm x 7-1/4 677M 11/16 x 7-3/ ALL PROFILES AT 50% OF ACTUAL SIZE. ALL PROFILES AT 50% OF ACTUAL SIZE.

14 Ultralite Supercoat Mouldings s & Misc. ULTRALITE SUPERCOAT Create Your Own Custom Look The Possibilities are Endless! Ultralite Supercoat Installation Instructions Handling Always carry Ultralite Supercoat on edge as this is where the strength of the product is. 4-1/4 48M Please Note As with all wood moulding, a small gap should be left on the mitered corners when applying baseboards. This gap can be easily filled with paintable latex caulking and will allow for the natural expansion and contraction of the baseboard. 5-1/4 4-1/4 545M Storage As with any interior product, Ultralite Supercoat should be stored in a clean dry place. To ensure easy installation, the moulding should be left in the job area for hours to allow them to acclimate. This enables the product to adjust to the relative humidity levels of the work area. This is a good idea to remember for any wood moulding you work with. Cutting 785M 18mm x 4-5/8 814M 15/16 x 8-3/16 270M 18mm x 6-3/4 271M 18mm x 5-1/4 4-1/4 4-1/4 412M 48M 412M Ultralite Supercoat is handled exactly the same as any Fingerjoint Primed moulding. The best way to obtain consistent miter angles when cutting is to use a miter saw with a carbon tip blade. However, you can also obtain good results with a sharp saw & miter box. Finish Ultralite Supercoat Mouldings are primed with a superior two coat process that will permit the use of both water base and solvent base finish coats. Fastening 397M Chair Rail 25mm x 3-1/ M Wainscot 27mm x 1-3/4 222M Wainscot 9mm x 5-3/4 956LWWM Backer 12mm x 5-1/4 5-1/4 30mm 2-1/4 5010LM Architrave 473P Pneumatic Air Nailers: Tank pressure should run between p.s.i. The type of nail preferred is an 18 gauge chisel point T-Nail, 1 to 1-1/2 in length, depending on the profile thickness. Remember, as with any wood moulding, you should try to nail into the wood studs or jamb & also nail into the curved or cove part of the moulding to better hide the nail holes. Should you decide to hand nail, any good quality finishing nail, properly countersunk, will work well. Glue Mitered Corners: As Ultralite Supercoat is more dimensionally stable than regular wood, it is not necessary to toe nail mitered corners. Instead, use a bead of white wood glue to hold the miter corner together. This, along with face nailing the casing, will produce a superior joint that won t pull apart. ALL PROFILES AT 50% OF ACTUAL SIZE.

15 s s are placed along the wall at the ceiling. They come in a wide range of patterns and sizes. s soften the transition from wall to ceiling while adding a distinctive look and charm to your room. Coves Coves are commonly used to soften the transition on inside corners but may be used for a wide range of applications. Cove 100P 11/16 x 11/16-16 Primed FJ /16 x 11/16 - RDM Solid Pine Cove 86 9/16 x 1-5/8 - RDM Solid Pine Corners Corners are used to protect the outside edges of the wall from damage and abrasion. Corners come in a wide variety of sizes and detailing. 49M 15mm x 3-5/8-16 Ultralite MDF 49LFJ 9/16 x 3-5/8-16 Raw Fingerjoint 49LP 9/16 x 3-5/8-16 Primed FJ 49L 9/16 x 3-5/8 - RDM Solid Pine Outside Corner /8 x 1-1/8 - RDM Solid Pine 205F08 1-1/8 x 1-1/8-8 Solid Pine Outside Corner /16 x 11/16 - RDM Solid Pine 206F08 11/16 x 11/16-8 Solid Pine M 18mm x 5-1/4-16 Ultralite MDF 28

16 Chair Rails Chair Rails are practical as well as decorative. Applied to a wall, from 24 to 48 inches up from the floor, they protect the wall from scuffs and dents from the backs of chairs as well as adding a distinctive accent to any room. Colonial Chair Rail 397M 25mm x 3-1/2-16 Ultralite MDF 397P 1 x 3-1/2-16 Primed FJ Chair Rails & Backers Chair Rails are practical as well as decorative. Applied to a wall, from 24 to 48 inches up from the floor, they protect the wall from scuffs and dents from the backs of chairs as well as adding a distinctive accent to any room. Chair Rail Backer 956WWP 7/16 x 4-1/4-16 Primed FJ 956WW 7/16 x 4-1/4 - RDM Solid Pine 390SDM Colonial Chair Rail 11/16 x 2-5/8-16 Ultralite MDF Colonial Chair Rail 390P 11/16 x 2-5/8-16 Primed FJ /16 x 2-5/8 - RDM Solid Pine Chair Rail 392P 1 x 2-3/8-16 Primed FJ x 2-3/8 - RDM Solid Pine Chair Rail 302P 1 x 2-3/4-16 Primed FJ /4 x 2-3/4 - RDM Solid Pine Chair Rail 297P 11/16 x 3-16 Primed FJ Chair Rail 390HPF17 1-1/16 x 2-3/8-17 Primed FJ 29 Chair Rail 300P 1-1/16 x 3-16 Primed FJ /16 x 3 - RDM Solid Pine Chair Rail Backer 956LWWM 12mm x 5-1/4-16 Ultralite MDF 30

17 Full, Half & Quarter Rounds & Base Shoes Quarter Rounds come in several sizes and serve a variety of functions. They are most often used with baseboards. A cross section of a Half Round looks like a half circle and is used primarily as decorative trim. It works well as a trim piece for wall paper or to add a decorative pattern to flat panels. This profile can also be used to put a rounded edge on various shelving. Full Rounds are used for numerous purposes and projects. Some of the more common uses are closet poles, curtain rods and towel rods. Base Shoes are primarily used to trim flooring materials and are often used in combination with a traditional baseboard to conceal variations between the flooring and the base. This versatile profile works great to solve numerous trimming needs. Base Shoe 129P 7/16 x 11/16-16 Primed FJ 129 7/16 x 11/16 - RDM Solid Pine Brickmoulds & Lattice A Brickmould is used as exterior casing around doors. 2 inches is the most common size. A Lattice is a thin strip of flat moulding commonly used to hide seams and trim edges. It is available in a multitude of widths and is useful for a wide variety of projects. Brickmould 176P 5/8 x 1-5/8-17 Primed FJ 176PI85 5/8 x 1-5/8-85 Primed FJ Brickmould 180P 1-1/4 x 2-17 Primed FJ 180LPVCF18 1-1/4 x /2 PVC Quarter Round 108 1/2 x 1/2 - RDM Solid Pine Lattice 267 1/4 x 1-3/8 - RDM Solid Pine 267I102 1/4 x 1-3/8-102 Solid Pine Lattice 266 1/4 x 1-1/2 - RDM Solid Pine 266I102 1/4 x 1-1/2-102 Solid Pine Quarter Round /16 x 1-1/16 - RDM Solid Pine Handrails Handrails provide safety and support. Quarter Round 106P 11/16 x 11/16-16 Primed FJ 106PF08 11/16 x 11/16-8 Primed FJ /16 x 11/16 - RDM Solid Pine 106F08 11/16 x 11/16-8 Solid Pine Full Round /16 - RDM Solid Pine /16 - RDM Solid Pine Half Round /16 x 1-1/2 - RDM Solid Pine 122 3/8 x 11/16 - RDM Solid Pine Handrail 240P 1-1/4 x 2-1/4-17 Primed FJ Handrail /2 x 1-11/16 - RDM Solid Pine 31 32

18 Door Stops The Door Stop mouldings are attached to the door jamb on both sides and at the top. It is where the door comes to a rest when it is closed stopping the door from moving any further, and covering the gap that would otherwise appear between the door and the jambs. Wainscot Trimwork installed in the area below a chair rail. Numerous options are available including raised panel, shadow box and beaded. Combined with a chair rail and baseboard, Wainscoting creates a dramatic look to any room. Wainscot 850M 27mm x 1-3/4-8 Ultralite MDF Wainscot 222M 9mm x 5-3/4-10 Ultralite MDF Door Stop 887FJF07 3/8 x 1-1/4-85 Raw Fingerjoint 887PI102 3/8 x 1-1/4-102 Primed FJ 887PF07 3/8 x 1-1/4-85 Primed FJ 887 3/8 x 1-1/4 - RDM Solid Pine Door Stop 916FJI102 3/8 x 1-3/8-102 Raw Fingerjoint 916FJF07 3/8 x 1-3/8-7 Raw Fingerjoint 916PF17 3/8 x 1-3/8-17 Primed FJ 916PI102 3/8 x 1-3/8-102 Primed FJ 916PF07 3/8 x 1-3/8-85 Primed FJ 916 3/8 x 1-3/8 - RDM Solid Pine 916I102 3/8 x 1-3/8-102 Solid Pine 916F07 3/8 x 1-7/8-7 Solid Pine Base Caps Door Stop 856F07 3/8 x 1-3/8-7 Solid Pine Base Cap /16 x 1-1/8 Solid Pine 33 Ogee Cap 163P 11/16 x 1-3/8-16 Primed FJ /16 x 1-3/8 - RDM Solid Pine Base Cap /16 x 1-1/4 - RDM Solid Pine 34

19 Screen Moulds & Parting Beads A very versatile profile; Screen Moulds fit a wide variety of needs and uses. Traditionally used to hold mesh screening into wood screens, it also works well as edge trim on various shelving or wood trim for wall finishes. Parting Beads are used in a wide range of applications including filling gaps and transitioning heights. This profile may also be used in a variety of craft projects. Window Stools Also called window sill, a Window Stool is the surface installed below the sash of a window. Trim installed under window stool creates a distinctive look and adds a decorative touch. Stool 1021P 11/16 x 5-1/4-16 Primed FJ 1021WP Stool 11/16 x 7-1/4-16 Primed FJ Parting Bead 254 1/2 x 3/4 - RDM Solid Pine S4S Baluster /16 x 1-5/8 - RDM Solid Pine Misc. Profiles These profiles have a wide variety of uses. Screen Bead 142 1/4 x 3/4 - RDM Solid Pine 142F08 1/4 x 3/4-8 Solid Pine Mullion 984 3/8 x 1-1/8 Solid Pine 984I102 3/8 x 1-1/8-102 Solid Pine 35 Screen Bead /16 x 1-1/4 - RDM Solid Pine Screen Bead 1217P 1/2 x 1-7/16-16 Primed FJ Mullion 985 1/2 x 2-1/4 - RDM Solid Pine 987L 3/8 x 1-3/8 Solid Pine 987LI102 3/8 x 1-3/8-102 Solid Pine Mullion 989 3/8 x 1-1/2 - RDM Solid Pine 989I102 3/8 x 1-1/2-102 Solid Pine 36

20 Misc. Profiles These profiles have a wide variety of uses. Accessories These profiles have a wide variety of uses. Backband /16 x 1-1/8 - RDM Solid Pine Rosette-Bullseye R /16 x 3-3/4 x 3-3/4 Solid Pine R3A1 7/8 x 2-1/2 x 2-1/2 Solid Pine R4S 7/8 x 3-3/4 x 3-3/4 Solid Pine Backband /16 x 1-5/8 - RDM Solid Pine Shingle 212B2P 11/16 x 2-1/2-16 Primed FJ Plinth Block PB30 7/8 x 3-3/4 x 6 Solid Pine PB /8 x 2-1/2 x 6 Solid Pine 37 Picture Mould 273P 11/16 x 1-3/4-16 Primed FJ Chamfer Strip 995 3/4 x 3/4 - RDM Solid Pine 38

21 Finish Lumber (S4S) S4S is an acronym that stands for Surfaced 4 Sides and designates dimensional lumber that has been planed on all sides. This versatile product can be used both as a moulding and as a high-grade project board. Ultralite MDF Primed Fingerjoint Raw Fingerjoint Solid Pine Chinese Fir - Gesso Primed Flat Jambs 4-5/8 x 81 BELOW DADO 4-5/8 x 81-1/4 BeloW DAdo 4-5/8 x 97 BELOW DADO 4-7/8 x 81 BELOW DADO 4-7/8 x 97 BELOW DADO 5-1/4 x 81 BELOW DADO RAW FJ X x X x 5-1/4 x 97 BELOW DADO PFJ X X X x x X X CLEAR VENEER X 7-1/4 x 97 BELOW DADO 21/32 x 3-1/2 23/32 x 3-1/2 18mm x 3-1/2 21/32 x 5-1/2 23/32 x 5-1/2 ULTRALITE MDF 16 X X X X X RAW FJ Edge 16 X X X X X SOLID PINE RDM /4 3/4 3/4 3/4 3/4 Chinese Fir - gesso primed 16 x x x x x 18mm x 5-1/2 21/32 x 7-1/4 23/32 x 7-1/4 18mm x 7-1/4 21/32 x 9-1/4 23/32 x 9-1/4 18mm x 9-1/4 21/32 x 11-1/4 23/32 x 11-1/4 18mm x 11-1/4 Split Jambs 4-5/8 x 81 (2-1/2 MALE MEMBER) 4-5/8 x 81 (2-3/4 MALE MEMBER) RAW FJ X X 4-5/8 x 97 (2-1/2 MALE MEMBER) PFJ X X X Flex Moulding BY: Exterior Frames KERFED & DADO 1-1/4 x 4-9/16 x 82-1/4 BELOW DADO 1-1/4 x 4-9/16 x 98-1/4 BELOW DADO 1-1/4 x 5-1/4 x 82-1/4 BELOW DADO 1-1/4 x 5-1/4 x 98-1/4 BELOW DADO WE HAVE A LARGE SELECTION OF FLEXIBLE MOULDINGS IN STOCK MOULDED TO MATCH MOST M&M PROFILES. ALSO, THE ABILITY TO PRODUCE ANY PATTERN CUSTOM FIT TO YOUR SPECIFICATIONS PFJ X X X X True Radius Round Top Half Circle True Radius Quarter Circle True Radius Full Circle ARC Eyebrow Segment 39 40

22 Case/Base Combinations Ceiling Trim option 1 option 2 option 3 Ceiling Trim Option #1 Ceiling Trim Option #2 #8063M #411M #535M #8263M #412M #545M #623M #47M #412M #41M option 4 option 5 option 6 #523M #366 #9053 #163EM7 #631 #9253 Ceiling Trim Option #3 Ceiling Trim Option #4 #48 #48 option 7 #356 #163E7M option 8 #473 #713 option 9 #9063 #92 #545 #623 #

23 Ceiling Trim Product Index Ceiling Trim Option #5 Ceiling Trim Option #6 0300B Architrave 11/16 x 2-1/ /16 x 3-1/4 37L 11/16 x 2-1/ mm x 6-5/16 45BC 9/16 x 5-1/4 45L 15mm x 5-1/4 45L 9/16 x 5-1/ mm x 4-5/8 pg 8 pg 7 pg 7 pg 15 pg 17 pg 15 pg 18 pg 18 47L 9/16 x 4-5/8 48 9/16 x 4-1/ mm x 3-5/8 49L 9/16 x 3-5/8 51 9/16 x 3-1/4 52 9/16 x 2-3/ mm x 5-5/ /16 x 1-5/8 pg 18 pg 17 pg 27 pg 27 pg 17 pg 17 pg 14 pg Cove 9/16 x 1-5/8 92 9/16 x 7-3/8 100 Cove 11/16 x 11/ Quarter Round 1-1/16 x 1-1/ Quarter Round 11/16 x 11/ Quarter Round 1/2 x 1/2 116 Half Round 11/16 x 1-1/2 122 Half Round 3/8 x 11/16 #163E7 #41 #545 #60 pg Base Shoe 7/16 x 11/16 pg & 180L Brickmould 1-1/4 x 2 pg Screen Bead 1/4 x 3/4 pg Outside Corner 1-1/8 x 1-1/8 pg /16 x 5-1/4 pg Outside Corner 11/16 x 11/16 pg Ogee Cap 11/16 x 1-3/8 pg Shingle 11/16 x 2-1/2 pg E Speed Base 15mm x 5-1/4 9/16 x 5-1/4 pg Wainscot 9mm x 5-3/4 pg E7 Speed Base 15mm x 7-1/4 pg Handrail 1-1/2 x 1-11/16 pg Base Cap 11/16 x 1-1/8 pg Full Round 1-7/16 pg Brickmould 5/8 x 1-5/8 pg Full Round 1-5/16 pg 32 pg 28 pg 28 pg 37 pg 34 pg 32 pg 31 pg Handrail 1-1/4 x 2-1/4 249 Balluster 11/16 x 1-5/8 254 Parting Bead 1/2 x 3/4 266 Lattice 1/4 x 1-1/2 267 Lattice 1/4 x 1-3/ mm x 6-3/ mm x 5-1/4 273 Picture Mould 11/16 x 1-3/4 Ceiling Trim Option #7 Ceiling Trim Option #8 pg 32 pg 35 pg 35 pg 32 pg 32 pg 20 pg 27 pg Backband 11/16 x 1-1/8 289 Backband 1-1/16 x 1-5/8 297 Chair Rail 11/16 x Chair Rail 1-1/16 x Chair Rail 1 x 2-3/4 1-1/4 x 2-3/ /16 x 3-3/ mm x 3-1/4 327 Ranch 11/16 x 2-1/4 pg 37 pg 37 pg 29 pg 29 pg 30 pg 8 pg 6 pg Colonial 15mm x 2-1/4 11/16 x 2-1/ mm x 2-1/4 11/16 x 2-1/4 376 Beaded 11/16 x 2-1/4 390 Chair Rail 11/16 x 2-5/8 390H 1-1/16 x 2-3/8 390H Chair Rail 1-1/16 x 2-3/8 390SD Chair Rail 11/16 x 2-5/8 392 Chair Rail 1 x 2-3/8 pg 5 pg 5 pg 6 pg 29 pg 6 pg 30 pg 29 pg 29 #620 #60 #8263 # Chair Rail 25mm x 3-1/2 1 x 3-1/2 pg L Beaded 18mm x 3-1/ /16 x 3 pg /16 x 4-5/ /16 x 4-1/4 pg /16 x 2-3/ mm x 3-7/8 pg /16 x 2-1/ /16 x 3-1/4 pg 5 504L 11/16 x 7-1/ /16 x 3-1/4 pg /Architrave 25mm x 3-1/2 1-1/16 x 3-1/2 444 Colonial 11/16 x 3-1/2 pg 5 523L /Architrave 11/16 x 3-1/4 445 Beaded 11/16 x 3-1/4 pg /16 x 5-1/4 pg 6 pg 16 pg 8 pg 5 pg 14 pg 8 pg 8 pg mm x 3-1/ mm x /16 x 6-1/4 618 Ogee Base 12mm x 5-1/4 9/16 x 5-1/4 620 Ogee Base 12mm x 4-1/4 9/16 x 4-1/4 623 Ogee Base 12mm x 3-1/4 9/16 x 3-1/4 631 Step Base 12mm x 3-1/4 9/16 x 3-1/4 631L Step Base 9/16 x 5-1/4 pg 6 pg 11 pg 20 pg 10 pg 10 pg 10 pg 10 pg /16 x 6-1/ /16 x 7-3/ /16 x 5-1/4 713 Ranch Base 9/16 x 3-1/ /16 x 7 11/16 x 7-1/4 714L 11/16 x 7-1/ mm x 7-1/ /16 x 7-1/4 pg 16 pg 16 pg 13 pg 10 pg 19 pg 18 pg 15 pg 9 725B 18mm x 7-1/ mm x 4-5/ /16 x 8-3/ Wainscot 27mm x 1-3/4 856 Door Stop 3/8 x 1-3/8 887 Door Stop 3/8 x 1-1/4 916 Door Stop 3/8 x 1-3/8 3/8 x 1-7/8 956WW Chair Rail Backer 7/16 x 4-1/4 pg 9 pg 19 pg 19 pg 34 pg 33 pg 33 pg 33 pg

24 Product Index 956LWW Chair Rail Backer 12mm x 5-1/4 984 Mullion 3/8 x 1-1/8 985 Mullion 1/2 x 2-1/4 987L Mullion 3/8 x 1-3/8 989 Mullion 3/8 x 1-1/2 995 Chamfer Strip 3/4 x 3/ /16 x 3-9/ Stool 11/16 x 5-1/4 Making Interiors Spectacular Moulding Gallery pg 30 pg 36 pg 36 pg 36 pg 36 pg 37 pg 7 pg W Stool 11/16 x 7-1/ Base Cap 11/16 x 1-1/ Screen Bead 9/16 x 1-1/ Screen Bead 1/2 x 1-7/ mm x 5-1/4 9/16 x 4-1/ /16 x 3-1/ /16 x 4-1/4 5010L Architrave 30mm x 5-1/4 pg 35 pg 34 pg 35 pg 35 pg 12 pg 6 pg 11 pg Speed Base 15mm x 5-1/4 9/16 x 5-1/ /16 x 6-1/ /16 x 6-1/ /16 x 3-1/ mm x 6-1/ mm x 4-1/ mm x 4-1/ mm x 6-3/4 pg 11 pg 13 pg 11 pg 7 pg 9 pg 7 pg 7 pg mm x 7 PB30 Plinth 7/8 x 3-3/4 x 6 PB78212 Plinth 7/8 x 2-1/2 x 6 R375 Bullseye Rosette 1-1/16 x 3-3/4 x 3-3/4 R3A1 Bullseye Rosette 7/8 x 2-1/2 x 2-1/2 R4S Bullseye Rosette 7/8 x 3-3/4 x 3-3/4 pg 9 pg 38 pg 38 pg 38 pg 38 pg 38 Storage, Handling and Preparation of all Mouldings and S4S Boards Until the time this product has been correctly final coated (after painting or staining) and installed, in conformance with all paint manufacturer recommendations as well as the highest and best building practices, respectively, for intended use, it must be continuously and effectively protected from exposure to direct sunlight, ground contact and the elements. It should be stored only in a dry, clean location and transported only if fully protected from water. As a final preparation before installation: (a) indoors, the product must be acclimated to the environment by storing it in the installation space for at least 3 days (with both faces exposed to the air in that space); (b) outdoors, every surface lacking both primer and final coat must be effectively coated to achieve protection recommended by the paint manufacturer respecting intended use. 45

25 Making Interiors Spectacular Moulding & Millwork is North America s leading supplier of mouldings. We offer the largest and most innovative selection of quality products. Take advantage of virtually endless possibilities. MOULDING & MILLWORK INC. ORLANDO Suite Southland Blvd. Orlando, FL t t f Printed 03/11