ADSGPS V2.22 ADSGPS A1001. GPS 10 Hertz. Force- G 3 Axes. Manual (ENG) ADSGPS V2.2.2 ( ) Alfano, S.A. Tous droits réservés.

Transcription

1 ADSGPS A1001 GPS 10 Hertz Force- G 3 Axes Manual (ENG) ADSGPS V2.2.2 ( ) 1

2 Tracks Management ADSGPS V2.22 ADSGPS Introduction 3 Installation 4 Power supply 4 Battery 5 Power on/off, backlight 6 The «HOME» window 7 Shortcuts 8 The most used symbols 9 Setup (configurations) Power off (Switch off) 10 Bluetooth 10 Track Closed 10 Track Open /trial 11 Track slalom 11 Track rally 11 Display: contrast, LED lighting, temps, backlight 11 Hour/date 12 Driver 12 GPS signal 12 Running counters 13 Peak 13 Graphic Adjustment 13 Recording frequencies 13 Units 14 G-force 14 Default settings 14 Language 14 Update 14 a) GPS creation 15 b) Import via Track Manager 21 c) Import via Bluetooth from a second device ALFANO 21 Start a timing session and use Alfano in race 23 DATA (Menu) Best Time, «Absolute» & «Last Session» 26 DATA 26 The Track used 26 Erasing data 26 DATA 27 Downloading 30 Track detection 31 Race window (layout) 32 Led 37 Accessories & power system 38 Memory 40 GPS reception 41 2

3 Introduction ADSGPS consists of 6 LEDs and 4 buttons. Each button is associated with the corresponding menu displayed on the HOME screen. 3

4 Installation Installing the "ADSGPS" Display 1) For optimal reception quality of the ADSGPS, the antenna located in the compartment at the top right of the ADSGPS must have a good clearance 2)Avoid passing the brake and acceleration cables in front of the antenna. 3) We recommend placing, as far as possible, from the motorcycle gauge (see picture on left). 4) Camera waves (GoPro or other) strongly disrupt GPS waves. A minimum gap of 30 cm is required between the ADSGPS and the camera. Power Supply The ADSGPS is supplied with 2 AA 1.5V batteries but can also work with 2 AA 1.2V rechargeable batteries which offer very good results, with an ALFANO external power supply (Art.Nr.: A4002) connected to a battery of voltage between 6V and 18V, or an ALFANO battery (Art.-No.: A4006). An energy gauge in the home menu shows you the power of the power supply. When the power becomes too weak (used batteries or discharged accumulators), a message warns you. When this message appears, the ADSGPS turns off automatically after 10 seconds. Note: - Remember to check your energy gauge before starting a race if it lasts a long time. - The consumption as well as the discharge speed of the batteries depends on the quality and type of battery, so it is strongly recommended to change the batteries as soon as the prevention message. Use with old batteries will damage the batteries and may damage your ADSGPS. - Value, as an indication, for charged or new batteries: - Average consumption without backlight in race ~25 h autonomy - Average consumption with backlight at 50% (value 5) ~14 h autonomy - Average consumption with 90% backlight (value 9) ~10 h autonomy - More than 100h with the ALFANO battery with backlight at 50% (value5). 4

5 Attention: These values are given for information only, it also depends on the quality of the batteries. Battery The technology applied to our new systems requires a higher energy consumption, the quality of the battery is important, a bad brand can lose its energy after a few months of storage even out of use. There are 3 major families of AA batteries on the market. Salines : they only have about a third of the energy of an Alkaline. Alkalines : these are the most common batteries on the market. Rechargeables : Very good compromise, but the differences in quality from one brand to another are important. A bad brand loses its energy even out of use, and up to 1% per day, moreover, these batteries have a memory effect, if you charge a battery that is half full, with use, you will not be able to use only half of the energy stored, the other half will be lost forever. There are very good rechargeable batteries whose off-duty discharge is less than 12% per year and have little or no memory effect. Examples of recommended brands: SANYO Enellope XX and UNIROSS Hydro, are known by photography professionals IMPORTANT WARNING Always use branded and quality batteries. Never leave the batteries in your device if it is not used within 2 to 3 weeks to prevent battery leakage electronics causing irreparable damage. The guarantee does not work in the event of battery leakage. 5

6 Turn on, backlight and turn off the ALFANO Backlight : press button 4, bottom right. Backlight: Depending on the setting in the DISPLAY menu in SETUP, the ALFANO is activated in different ways: «OFF» : The ALFANO turns on without the backlighting: "MAN": The ALFANO offers the backlight: To activate it: press «ON», then, possibility to adjust its light output. To not activate it: press "OFF" or do nothing for 3 seconds. "1-9": The ALFANO turns on automatically with the backlight. Finally, the ALFANO is positioned in "HOME". To note: Backlight consumption decreases battery life by +/- 20 to 40%. Turn off in manual: in "HOME", press the same button for 2 seconds. Turn off automatically: he system turns off after being inactive for a time that can be set in SETUP menu Display, from 1 to 60 minutes. 6

7 «HOME» The "HOME" window is the main window of the ALFANO. The menus in this window give access to the settings of the "SETUP" parameters, the visualization of "DATA" data, the detection of tracks when GPS is selected, the choice of race windows (LAYOUTS) and through shortcuts: direct access to the data of the last SESSION, activation or deactivation of the backlight, activation of the Bluetooth module, shutdown of the system. DATA Track detection (Button 1) (Button 2) Gauge status batteries Gauge of memory available Setup (Button 3) Backlight active (Buton 4) Turn Layouts of Racing Performance, road Bluetooth activation Switch off 7

8 Shortcuts Shortcuts allow you to fly over several passes to directly reach a desired display or option. In "HOME": - 1 second press on the button 1 = direct access to the data of the last SESSION. - 1 second press on the button 3 = switch the backlight on or off. - 1 second press on button 4 = activates Bluetooth - 2 seconds press on button 4 = system shutdown 8

9 The most used symbols Buttons 1, 3 : o left and right arrows move from one menu to another, in some cases prolonged pressure allows faster scrolling. p and down arrows allow you to move from one option to another, to change numeric and alphabetical values, in some cases prolonged pressure allows for faster scrolling. Button 2 : allows you to confirm a status and at the same time, in some cases, to move to the next option. Button 4 : o allows you to go back or exit a menu... 9

10 SETUP (configuration) In "HOME", press SETUP: Power off Press "OK" to turn off the ALFANO. Bluetooth Customize the personal code to protect your data during the connection (default code "000000"). the device name and Pin Code are not editable, they are unique for each device. CAUTION: This window does not activate Bluetooth. Closed track 10

11 Management of closed tracks (Detailed in the track Management chapter) Open track Management of open tracks (Detailed in the track Management chapter) Slalom track Management of slalom tracks (Detailed in the track Management chapter) Rally track Management of closed tracks (Detailed in the track Management chapter) Display 11

12 Set: the contrast of the screen, the power of the LEDs, the time for automatic shutdown, Backlight: o "OFF": The ALFANO lights up without. o "MAN": The ALFANO offers it. o o "1-9": The ALFANO automatically turns on with. (Set its light output from 1 to 9). Time / date setting Set the format of the date and time zone, because the date and time are provided by the satellites in GMT, this information is visible only in the presence of these. Pilot Ability to edit up to 3 driver names. The chosen driver will be associated with the TIME SESSION. To choose a driver: select it with the arrows on the left, then press "OK". To change the name of the driver: press "OK" for 3 seconds on the name to be changed. GPS reception Check: the intensity of the satellite signals, GPS coordinates in real time, the date and time in GMT, altitude. Running counters 12

13 Two counters available: the first accumulates the total time, the second accumulates the distance traveled. Press "OK" for 1 second to reset the selected counter. Peak Allows you to freeze information on the screen, for an adjustable period of time, to have the time to view them. - Setting the lap times display time: from 1 to 60 seconds or fixed. - Setting the display time of the Partial Times: from 1 to 60 seconds or fixed. - - Setting the speed point display time: from 1 to 60 seconds or fixed. Graphic adjustment Set: The height of the bar graphs sized by the time can be set from 0.5 seconds to 10 seconds between the low level and the high level. This is to better observe the time differences between each lap in the DATA menu. Recording frequencies Set: 10 hertz > every 100 ms 5 hertz > every 200 ms 2 hertz > every 500 ms 0 hertz > Null This last option is useful for endurance races. In this case, only split times and lap times are recorded. Note: observe the remaining time and the total available time, these will depend on the chosen frequency Unit 13

14 Set: Imperial (Mph) or Metric (Km / h) G-Force Enable the Force G sensor or not. Note: Force-G sensor data can be analyzed only with the PC Software. Activating the Force-G sensor shortens the memory duration by +/- 30%. Default settings Restore the factory settings, press "OK" for 3 seconds to start the procedure. Note: this procedure clears the tracks and the recorded data. languages Set: French English Italian Deutsch Spanish Portuguese Update 14

15 This menu is to enable Bluetooth to UPDATE the system. All necessary codes are displayed to synchronize with the PC. CAUTION: Some PCs are difficult to connect to a Bluetooth connection, in which case it is best to use the USB-Bluetooth key supplied with the ALFANO. (Details see chapter Update). Track Management " To choose " View or rename an existing track. "New" Create a new track. " Remove " Delete an existing track. " To send " Send an existing track via Bluetooth to another ADSGPS. " To receive " Receive, via Bluetooth, a track from another ADSGPS. Information For the visualization and the logical recording of the data, it is necessary, before using the ALFANO in race, to configure the morphology of the track. This menu consists of creating tracks (80 maximum) and saving them. a) Creation of a GPS track Name of the track Press the button corresponding to 'OK' to enter the name of the new track (11 characters maximum), you can use the 26 letters of the alphabet, 10 digits from 0 to 9 and the space. You must go to the end of the 11 characters to validate the name of the track. 1- GPS position record. 15

16 Press the button corresponding to 'OK' to record the GPS positions. a) Closed track. The recording is done by rolling. Press the button at the top right corresponding to 'Start' as you cross the start line to record the GPS coordinates of the start line. If you wish, you can save the GPS coordinates of 4 partial times by pressing the button at the top right and the GPS coordinates of 5 speed points by pressing the button at the top left. When your turn is complete, the ADSGPS will automatically recognize your starting line and complete the recording of the track. Your new track will then be saved in the memory of the ADSGPS Open track 16

17 Check-in at the start line is stopped. The partial times will be done while driving. Go to the start line and press the button at the top right corresponding to 'OK' to save the GPS coordinates of the start line. If you wish, you can save the GPS coordinates of 4 partial times by pressing the button at the top right and the GPS coordinates of 5 speed points by pressing the button at the top left. A short press on the bottom left button will record the GPS coordinates of the finish line and finalize the recording of the track. Your new track will then be saved in the memory of the ADSGPS End of the registration b) Slalom track The slalom is an open track with several passages on the finish line. The number of passages on the finish line (maximum 4) must be set during the creation of the track. If, for example, the number of finish passes = 2: we will then have the starting line, 2 passages on the finishing line corresponding to the partial times and the 3rd crossing on the finishing line which will finally close the session.. Check-in at the start line is stopped. Go to the start line and press the button at the top right corresponding to 'OK' to save the GPS coordinates of the start line. 17

18 A brief press on the button at the bottom left records the GPS coordinates of the finish line. The split times will be the number of passes on the finish line. End of the registration In the track list, the displayed track will be accompanied by its ID, example: "45D8-23G1" Possibility to replace the name of the track (LAP, TRIAL, SLALOM), in "Tracks List", a pressure of 1 second on the button 'OK', you activate the following window and you repeat the same operations as when you create a new track. Note: only the name can be changed, not GPS positions, ID remains the same. c) Rally track 18

19 A rally track includes several sectors. The area can be a transfer, a special or a service park. Only special stage times will be stored in the ADSGPS. Each sector must be previously set in the ADSGPS using the log book. You must enter the type of sector (transfer, special or park), for transfers and specials you must enter the time of the trip and its distance. The ADSGPS will then automatically give the average speed to respect the rules of the rally. ("Composition"). Note: the service park areas will only be used to respect a correct chronology of the sectors in relation to the log book. We scroll through the different sectors with the button at the top left corresponding to 'S', we enter the sector to set it with the button at the top right corresponding to 'OK' Example: we set the first sector, we choose "transfer". After setting the sectors, return to the selection menu by pressing the button at the bottom right. Then select "Save. Pos. GPS "and validate by pressing 'OK'. We can then start recording the GPS coordinates of the different sectors. (operation that can be done at another time) 19

20 Registration of the GPS coordinates of the Transfers and Special Areas ("GPS Position Record"), ex: - departures from sectors - the arrivals of the sectors - - If they are specials, it is also necessary the arrival of specials and possibly 4 partial and maximum 5 points of speed for each special, if you wish it. - Scroll through the different sectors with the button at the top left. - Scroll through the different points to be recorded with the button at the bottom left. Once the good sector and the good location selected (departure, arrival, speed, partial, etc....), you have two possibilities to record the GPS positions, ex: 1) Save the GPS positions on the spot by pressing 1 second on 'OK', the ADSGPS will capture the GPS positions and store them. 2) Save the GPS positions manually, for that, press the 'OK' button for 3 seconds. Almost all organizers of Rallye realize the log book by indicating the GPS positions for the departures and arrivals of transfers and specials. In this case, it is possible to insert the GPS positions manually. Tip: Use "Google Earth" to find missing GPS coordinates for speed and partial points. Note: A special behaves like an open track + the transfer zone that follows. Special times are stored in the ADSGPS, the transfer parameters are displayed for information only. 20

21 Example of displaying a special race. Example of transfer display. At the top, we can see the distance remaining before the arrival of the sector. In the middle, the time remaining, at the bottom, the average speed at which the pilot must roll to arrive without penalty. The direction of the arrows indicates to the pilot if it is in advance (arrow directed to the left) or late (arrow directed to the right). The number of arrows indicating to the pilot if the advance or the delay is important is greater or smaller. Important : - To have an optimal time calculation, you must save your point (Start, partial, speed) in a straight line. The orientation of the GPS will then be the best for GPS reception, unlike turns where the bike is lying, is the lower GPS reception. - For closed tracks, the direction is recorded when creating the track. Thus, if you pass the Start line in the opposite direction, the ADSGPS will not trigger the recording of the session. b) Creating a track with TrakManager software This software has been designed to manage your tracks: - Import tracks from an ADSGPS to a PC - Import tracks from the PC to an ADSGPS - Import tracks from the site ALFANO.COM - Create a file of the type "kml" to export the track on Google Earth - Export files "tracks" via internet, etc Create and edit Rally Tracks Procedure: c) Import tracks from another ALFANO, via Bluetooth «ALFANO-1133» «ALFANO-2055» send the track receives the track

22 Press "OK" on "Send" in the track menu. ALFANO is looking for a device. Press "OK" on "Receive" in the track menu. The ALFANO is waiting for connection. 3 4 The ALFANO has found several other ALFANOs, press "OK" on the 2055 device to request a connection. Press "OK" to accept the connection. 5 6 Choose the track from those stored in its memory and confirm with "OK". 7 Appears the name of the track to receive, press "OK" to accept the track. To note : tracks transferred between systems via Bluetooth identify themselves with a small icon Successful transfer. Note: The ID (identification) of the tracks. For each track created with the ADSGPS or with the software "TrackManager" the track will be accompanied by its ID, this identification will be composed of 8 alphanumeric (example: 58F4-45K6), this will be unique, if several ADSGPS use the same ID track, they will have the advantage of making precise comparisons that is to say: the partial times, the points of speed, the lap times will be captured with the same GPS coordinates. 22

23 Note: as soon as a Rally track is modified on the ADSGPS or with the "TrackManager" software, another ID is automatically assigned to it. Only rally tracks can be modified. For other types of track, once created, only the names can be changed (their structure and ID does not change). Another annotation: With the software "TrackManager" it is possible to lock a Rally track to no longer be able to modify it. A small closed lock will appear to the right of the name of the Rally. Start a timing session and use the Alfano in the race The ALFANO must be in "HOME" with the appropriate track. As soon as the starting zone is detected and if the speed is above 20km / h, the ALFANO starts the timing and records the data of these sensors for the closed tracks. For other types of tracks, stop in the departure zone, confirm the start, the recording will start as soon as the speed exceeds 10km / h. With the button above right, change the "Layout" window. 23

24 With the top left button, turn on or off the backlight. If the speed is zero, STOP is displayed, press one of the two bottom buttons to stop the timing and return to "Home". If the speed is zero for 10 minutes, the ADSGPS automatically stops the session. - For open tracks and slalom, position yourself at the starting line and stop. - Then press the button at the top right corresponding to 'OK' to activate the start. - For the rally, position yourself at the starting line and stop. The system automatically locates the start zone and indicates the membership of this zone. You can see the type and the number of the sector. The Rally may have several identical sectors. For this, the system will display, according to the course of the Rally, the right sector. But if it is not the case, you have the possibility to choose the correct sector, for that, maneuver the buttons of left. - Then press the button at the top right corresponding to 'OK' to activate the start. 24

25 The departure is then activated. The recording will start as soon as a speed greater than 5 km / h is detected. Speed detected, recording starts. You are then in the race. - A short press on the button at the bottom right makes it possible to change the type of display. - Pressing the button on the bottom left for one second stops the recording. a. «STOP» Fin de course - For open tracks, slalom and Rally, the ADSGPS stops the recording as soon as it crosses the finish line. This window will be displayed for 5 seconds. - Then, the completed time of the race will appear for 30 seconds to finally return to the home menu. - A brief press on one of the 4 buttons makes it possible to return more quickly to the home menu before the end of the 30 seconds. 25

26 - For closed tracks, the ADSGPS will show your best lap time and best lap time for 5 seconds, then return to the home menu. Note: if the race has not been completed and / or the first lap has not been completed by a closed track, no information will be visible in the DATA menu. b. «STOP» Missed race In "HOME", press the "DATA" button 1: - If you want to stop recording before the end of the race, then press the button at the bottom left for 1 second, this window is displayed for 3 seconds. - If the ADSGPS detects no more speed for 10 minutes, it will automatically stop the session / race to return to the home menu DATA (Menu) «BEST TOURS» This window shows for 5 seconds for the closed tracks, the best Absolute time among all the sessions and the best time of the Last SESSION, then return to "HOME". Press "OK" in this window to display the data analysis menu. See below. 26

27 «Saved Data» In "DATA" are all the data recorded on the track that is displayed in the center of the window, by default this is the last used track. Press "OK" to analyze this data. «Tracks used» Tracks with recorded data will be visible in this drop-down menu. Press "OK" to open the list, use the left arrows to choose, press "OK" to confirm. «Total data erasure». Press "OK", then press "OK" again for 3 seconds in the confirmation window that follows. Note: this command executes the total erasure of the recorded data of all the tracks DATA (Data) Press "OK" on the DATA icon: «BEST TOURS» «THEORETICAL TOUR» «SESSIONS» «Best Tours» and «Theoretical tour» are calculated on all Sessions. "Sessions" are listed by date and time. The last Session is selected by default. 27

28 Once your session is selected, you have the partial times and speed points displayed for the first lap of your session, you can select and analyze all the laps of your session using the two left buttons. Bar graphs represent your lap times. The lower left display shows your lap time, and the lower right clock indicates the difference between the selected lap and the best lap. BEST TOURS (on all sessions) Press "OK" on "BEST TOURS", this menu is to compare the best lap of the LAST SESSION with the best ABSOLUTE turn, press the double arrow to alternate the data of these two laps. "BEST TOURS" This window shows the absolute best time among all the sessions and the best time of the last session. THEORETICAL TOUR (on all sessions) Press "OK" on "THEORETICAL TOUR" This window shows the best partials performed on all sessions, and then calculates the theoretical time. Press "OK" on the desired partial to access the tower belonging to it. SESSIONS Press "OK" on the desired "SESSION". The complete analysis of the SESSION is done in 4 steps: Step 1 (only for closed tracks) Step 2 Step 3 Step 4 Best Tr./ Tr. Theoretical Tours / Races Acceleration / braking Graphical Analysis of the chosen SESSION of the chosen SESSION of the TOUR / COURSE chosen TOUR chosen 28

29 Step 1 "BEST LAP" (only for closed tracks) The best round of the SESSION with the best partial black background (only for closed tracks). Press to display the tour with the other best match. Press again on to display the theoretical turn of the SESSION "THEORETICAL TOUR". Press "OK" to display the "Step 2" window Step 2 "The TOURS" of the SESSION The cursor is automatically positioned on the best lap, the bar graphs represent the number of turns and the height indicates the time difference between each lap. The time difference between the low level and the top of the bar-graphs can be set in the "SETUP" menu 29

30 Use the arrows from the bottom to move from one turn to another, a long press allows fast scrolling, or from the top to display the times of the partials and speed points. Each round is accompanied by its time and the time difference from the best lap of the session with these times and Max / Min: SPEED. Press "OK" on the desired tour to continue the analysis in "Step 3". Step 3 "Acceleration / braking" View the acceleration and deceleration parameters for each lap. Step 4 "Graph Analysis" For a careful analysis, this option allows you to view the tour chosen in (step 2), step by step, according to the recording frequency chosen in the "SETUP": Speed (with graph). Use the arrows to go around the tour, a long press allows fast scrolling. The displayed curve is that of the speed. downloading (Download) There are currently 3 software compatible with ADSGPS: ADSGPSDATA TRACKMANAGER VISUALDATA The analysis software "ADSGPSDATA" also allows to recover the data of the ALFANO (See instructions for use of the Software). The VISUALDATA allows to download the closed track data and to export the data in format.xls or.csv to synchronize the data with the videos (GoPro or other...) The TRACKMANAGER allows you to manage your tracks. A database with more than 120 tracks around the world is available on the site at the following address: 1) Press button 4 for 1 second to activate the Bluetooth of the ALFANO 30

31 A window appears with the necessary information for the synchronization of these two devices. Enter this data + the personal password, configurable in the "SETUP". The transfer control is done from the Analysis software. This window confirms the connection with the PC. Track detection This menu is accessible by pressing the button at the top right when you are in the home menu and allows quick detection of tracks registered in the ADSGPS. This menu shows you, within a radius of 2 km maximum, the 3 nearest tracks recorded in the ADSGPS. You can then choose the track on which you want to ride. It must of course that the tracks were created beforehand or downloaded from the Database of our site. Note: If you select a rally, the ADSGPS automatically chooses the sector of this closest rally in a radius of 2km. It searches sectors every 20 seconds and switches automatically on the nearest, so the driver just chooses his rally, the selection of the special or transfer will be automatically. 31

32 In "HOME", press the button 4: RUNNING windows "Layouts" - Performance - Route - Course a. Performance There is a special menu to measure the performance of your vehicle. 32

33 0-100km/h in seconds meters in seconds meters in seconds meters in seconds Maximum speed km/h in seconds km/h in seconds Deceleration/ braking km/h in seconds To activate the performance menu, go on a track and stop. Pressing the button at the top right corresponding to 'OK' activates the performance menu, the ADSGPS waits for you to leave. As soon as a speed higher than 0 is detected, the ADSGPS calculates the performance of the vehicle. It is then necessary to make an acceleration, to reach at least 160 km / h, to traverse at least 1000 meters, and to brake from 100 to 0 km / h to obtain THE TOTALITY of information. You can also do this test over shorter distances or with lower speeds. The parameters meters, meters and km / h will remain null if you do not reach the minimum values of distance and speed. Note: It is important to perform acceleration and braking at the limit of the vehicle to get information closer to reality. b. Route This menu gives you only approximate values, the speed in real time, the distance traveled as well as the elapsed time. Pressing the right button, one second will reset the distance or elapsed time. Pressing the lower left button returns to the home menu. This display cannot be used in race mode, no recording is done in this menu. Note: This counter is independent of the total counter of the analysis menu. Note: after detection of zero km / h for 5 minutes the system returns to the home page. c. Race Display 33

34 There are currently 16 different types of display. Pressing the button at the bottom right scrolls through the different displays. A short press on the lower left button validates your default display. It will be possible to change the display running while driving with the same button at the bottom right. Each "Layout" is numbered to facilitate the choice, this figure with the word "confirm" appears only a few seconds. Press the "Confirm" button to choose it, even if this word is no longer visible on the screen. Race windows Course «1» Lap time display BEST display if you have just made the best lap time. Course «2» Lap time display Display time difference from best lap time and previous turn Course «3» Lap time display Display of the number of laps Display time difference from best lap time and previous turn 34

35 Course «4» Lap time display Display of the number of laps Display time difference from the best time Course «5» Lap time display Sector display Display time gap compared to the best current sector Course «6» Lap time display Display of the number of laps Course «7» Reverse lap time display vs. best lap time Display time difference from the best time Course «8» Time display accumulated on sectors Display of the number of laps Display time gap accumulated on the sectors compared best time accumulated. Course «9» Best lap time display Display time gap compared to the best lap Lap time display Display of the number of laps Time display Sector display Display time gap compared to the best current sector 35

36 Course «10» Best lap time display Speed display Lap time display Display of the number of laps Time display Sector display Display time gap compared to the best current sector Course «11» Speed point display Lap time display Display of the number of laps Time display Sector display Display time gap compared to the best current sector Course «12» Distance display Lap time display Display of the number of laps Time display Sector display Display time gap compared to the best current sector Course «13» Sector display Time display Display time deviation from the best lap or time difference from the best current sector Display of the number of laps Lap time display Course «14» Display of the number of laps Course «15» Sector display Time display Display time gap compared to the best current sector Display of the number of laps Lap time display 36

37 Course «16» Lap time display Display of the number of laps Speed display LED The ADSGPS has 6 leds, 2 red on the ends and 4 white centered. The 4 white LEDs light up 5 seconds when you make the best turn. These same 4 LEDs flash for 5 seconds when you perform the best partial. The 2 red leds are alarms. : - The right one flashes when your batteries become weak. Only a little energy remains. - The right one flashes when your memory is full, you can still roll but the ADSGPS will only record your lap times and not all samples. You will no longer have the plot on the ADSGPSDATA software, and your memory gauge will be full. You can adjust the power of the LEDs in the Setup / Display menu. The 4 white LEDs light up at the beginning of a session, this makes it possible to synchronize the data of the ADSGPS with the videos (Dashware). Use the VisualData software to export your data in.csv or xls format and then use Dashware. 37

38 Power Systems and Accessories Batteries A4019 Alkaline PROCELL 1.5V model «AA/R6» A4018 Rechargeable UNIROSS, 2050 mah Hybrio 1.2V A4016 Charger UNIROSS from 100 to 240V 50/60Hz 38

39 ! Without memory effect! A4017 ALFANO Rechargeable Block mah Li Ion 3.7V (Water Proof) 75x40x40mm Comes with a charger 100 to 240V 50 / 60Hz and a bag A

40 Complete power system A4002 Battery power supply 7-18 V Accessories A5001 A5002 Memory Also remember to check the available memory with the memory gauge in the home menu or the remaining time in the setup ---> REC menu. in order not to saturate the memory when you ride. 40

41 i. You can record up to 99 sessions per track. ii. You can record up to 327 sessions on all channels. iii. You can record a maximum of 99 laps per closed-track session, if you exceed, a new session will start automatically. (Example: iv. The maximum time is 1 hour per lap for closed, open and slalom tracks. Important note : - When the memory gauge in the main menu is full, the memory is almost full, one is automatically in endurance mode, one then records only the lap times, partial times with minimum and maximum, but not the samples. - When the memory gauge in the main menu is filled and flashing, the memory is full, so you cannot start a new session until the data has been erased. GPS reception When switching on your ADSGPS, it will wait for the GPS signal. The wait time at the reception depends on several parameters: - The environment in which the ADSGPS is located (building, forest, etc....) - The Cold Start or Warm Start: The ADSGPS captures the signal more quickly when it is used regularly, in fact, the longer the GPS stays off, the longer the waiting time before capturing the signal will be long at the next start, this is due to the GPS download (ephemeris, etc.) when it is off for several days. This waiting time can therefore vary from a few seconds to several minutes. Information regarding the quality of GPS reception: - It depends on the environment (building, forest, mounting) - The weather does not influence the satellite reception (overcast or clear sky). - Positioning of the ADSGPS (the antenna must be at the maximum towards the sky) - Antenna clearance (avoid metal boxes, brake cable / acceleration) just in front of the antenna). The GPS captures its real position from 3 satellites.. The higher the number of satellites captured, the better the accuracy of the position, and therefore the more precise timing times. We recommend timing from at least 8 satellites, otherwise the accuracy of the times cannot be guaranteed. As indicated in the Setup menu, the satellite gives us the GMT time and date, so set the time zone according to the position where the ADSGPS is in the Setup / Time and Date Setup menu. 41

42 Warranty All our devices have been thoroughly tested in the factory and are covered by a 24-month warranty against manufacturing defects. The guarantee comes into effect from the date of purchase. The date of purchase is the date indicated on the invoice / receipt issued at the time of purchase by the reseller. The manufacturer agrees to repair and replace, at no charge, parts with manufacturing defects during the warranty period. Defects that have not been clearly attributed to the material or workmanship will be examined at one of our authorized service centers or at our head office and billed based on the results. The guarantee does not apply in case of opening of the device, accidental damage, negligence or improper use, in case of improper installation, incorrect or not in accordance with the instructions in the manual and in case phenomena independent of the standards of operation and use of the device. The guarantee is canceled in the event of repair or manipulation by unauthorized third parties. The intervention under warranty does not entitle you to replace the device or extend the warranty. The warranty operation is carried out at one of our authorized service centers or at our headquarters. In the latter case, the piece must be sent to us free of charge, that is to say that the transport costs are borne by the user. The manufacturer declines all responsibility for damage to persons or property caused by improper installation or use of the device. Product Changes Alfano SA applies a method of continuous development. Therefore, Alfano SA reserves the right to make changes and improvements to any product described in this document, without notice. Damages and responsibilities The products being used under the sole direction and responsibility of the customer, the latter will bear the damage that the products could undergo or cause. No compensation will be granted for deprivation of enjoyment, ALFANO can not be held responsible for the direct or indirect consequences of their exploitation or their inuse. The obligations of ALFANO are obligations of means and not of result. Scrapping Disposal of the machine must be done in an environmentally friendly manner. The chronometer and its accessories have a lot of plastic parts. When the stopwatch or one of its accessories no longer works, they must be treated in accordance with the legislation of the country. Just like the old batteries that must be disposed of in accordance with the regulations in force in your country. 42

43 Rue de l Industrie, 3b 1400 NIVELLES (BELGIUM) 43